DHP-302_A1_ Manual_v1.10
Contents
1. Ethernet LED D Link A solid light indicates a connection on CEED the Ethernet port The LED blinks during data transmission Throughput LED A solid green light indicates that the master device has detected another Powerline device on the network Green LED Power Line speed gt 20Mbps non master unit Amber LED Power Line speed lt 20Mbps or gt 6Mbps non master unit Red LED Power Line speed lt 6Mbps or link is down non master unit D Link DHP 302 User Manual 5 Section 1 Product Overview Hardware Overview Connection Depressable push button Press to secure your network Refer to page 8 for more information Ethernet Port Connect CAT5 Ethernet cable to the DHP 302 Ethernet port D Link DHP 302 User Manual Section 2 Installation Hardware Installation Power Plug in the DHP 302 into an AC wall outlet or power strip Note Power source is confirmed when the green LED Power Indicator on the DHP 302 is illuminated Connect the Ethernet Cable Connect the included Ethernet cable to the network cable connector located on the DHP 302 and attach the other end of the Ethernet cable to the network or PC Network Connectivity is confirmed when the green LED Indicator on the DHP 302 located left of the Power LED is illuminated YOUR NETWORK SETUP POWERLINE DIGITIAL MEDIA r HD ADAPTER POWERLINE Second Floor R HD ADAPTER DESKTOP PC CABLE DSL2. Good powerline connection Suitable for data and Internet activity connection Scan Scan the powerline network for PLC nodes Check the AutoScan box to scan the network periodically Note Network ID can be changed to prevent unauthorized access to your powerline network Make sure the Network ID of the devices within your powerline network are the same to enable data transmission D Link DHP 302 User Manual 16 section 3 Configuration security This section shows the security configuration of the DHP 302 You can modify any of the parameters and click Save Setting to save your configuration D Link Powerline HD Utility D Link Powerline Setup Security Qos System PLC Node configuration Device Name Devices Network ID D Link or Each PLC node in the network must use the same Network ID Save Settings version 1 0 Device Name Show name of devices that have been discovered Default is Device 1 Device 2 etc Max 16 characters 0 9 A Z case sensitive ie Living room Bedroom etc Network ID Powerline Network Name Max 10 characters 0 9 A Z case sensitive Default is D Link Helpful Hints This is the current configuration of selected PLC node Complete the information for selected PLC node and then click button It s recommended to create your own Network ID for network security purpose The Metwork ID allows you to protect your network from unauthorized P
3. InstallShield Wizard 12 1 Welcome to the InstallShield Wizard for D Link Powerline HD Utility The InstallShield Wizard will install D Link Powerline HD Utility on your computer To continue click Next Click Next gt Cancel D Link DHP 302 User Manual 11 Section 2 Installation D Link Powerline HD Utility InstallShield Wizard Choose Destination Location Select folder where setup will install files stall Stel Click Next D Link Powerline HD Utility InstallShield Wizard InstallShield Wizard Complete D Link Powerline HD Utility installation is complete Launch D Link Powerline HD Utility Bancel Click Finish D Link DHP 302 User Manual 12 section 3 Configuration Configuration After you have completed the D Link Powerline Utility installation wizard double click the D Link Powerline HD Utility icon on your desktop to start the configuration of the DHP 302 Double click the D Link Powerline HD Utility icon D Link Powerline HD Utility The utility provides you with the option of setting your own dcii d ii unique Network ID and the ability to prioritize traffic passing through the network The color of text on the Device Name Powerine BEE ne Network ID MAG and Location columns represent the lt The assistant status of powerline network M AutoScan Finished Device Hame Network ID MAC Location Quality 9959 think more nodes
4. Synchronization complete After a few seconds successful synchronization should occur This is visible when the remote adapters AP LED switches off indicating that it is securely configured The local adapter AP LED however will continue to remain solidly lit and the throughput LED should turn Green Remote Adapter Local Adapter Note When adding more adapters repeat steps 1 to 3 At the end of this process only the local adapter should have the AP LED lit Also the adapters will keep their security settings even after the power is removed from the units To reset switch off any adapter security back to default Depress and hold up to 15 seconds the push button until the AP LED turns off This will reset the unit back to the factory default settings D Link DHP 302 User Manual 10 Section 2 Installation Using the Setup Wizard Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process Insert the D Link DHP 302 CD into your CD ROM drive If the CD Autorun function does not automatically start on your computer click Start gt Run In the Run command box type D DHP302 exe where D represents the drive letter of your CD ROM If it does start proceed to the next screen Click on Install Utility nm View QIG View Manual Adobe Reader Support The InstallShield Wizard will begin the DHP 302 software installation D Link Powerline HD Utility
5. should be shown e Green text Powerline network is encrypted with a non default Network ID connected and click button Check box ta scan all e Red text Powerline network is encrypted with the en default Network ID Bare Fe stren ath plug the device directly into e Grey text Powerline network is not connected due to se renee a different Network ID of power strips and extension COrds version 1 0 Copyright 2009 D Link Inc All Rights Reserved D Link DHP 302 User Manual 13 section 3 Configuration Red text on the Device Name Network ID MAC amp Location columns mean that the powerline network is encrypted with the default Network ID D Link Follow the steps below to encrypt the network with a non default Network ID e Single click on the nodes that you want to IRE change D Link e Once all the nodes you want to encrypt with a Powerline Setup Security QoS System non default Network ID are highlighted click PLC Node configuration the Security page Device Name e Change to different Network ID pas Press Save Settings Network ID D Link or Each PLC node in the network must use the same Network ID Save Settings version 1 0 D Link DHP 302 User Manual Helpful Hints This is the current configuration of selected PLC node Complete the information for selected PLC node and then click button It s recommended to create your own Network ID for ne
6. MODEM C WIRED GIGABIT POWERLINE ROUTER HD ADAPTER First Floor D Link DHP 302 User Manual Section 2 Installation Push Button Security Plug in all the adapters to be configured Note It is strongly recommended to designate the local adapter as the one that is directly connected to your router This local adapter will act as the security key master in the network Each additional adapter you proceed to add afterwards will be referred to as a remote adapter Local adapter Press and hold the push button down until the local adapter AP LED begins to flash Wait until the AP LED stops flashing up to 30 seconds At this point the local adapter is now assigned as the master adapter in your network Press and hold the button To proceed securing the remote adapters follow the 3 step process below Local Adapter Local Adapter D Link DHP 302 User Manual Section 2 Installation 1 Local adapter Begin by pressing the push button until its AP LED starts to flash During this flashing phase the adapter is actively waiting for other adapters to sync Press and hold the button Local Adapter 2 Remote additional adapters Push the button on the remote adapter until the AP LED begins flashing It is important to ensure the local adapter AP LED is still in the flashing state while you do this Press and hold the button Remote Adapter D Link DHP 302 User Manual Section 2 Installation 3
7. USER MANUAL VERSION 1 1 s p o p p P POWERLINE HD Table of Contents Table of Contents Product OvervieW vwcisccecicttccsteceatidennsscsscavessenstsruddotenacsexe 3 PENNE ve 3 System Requirements 5 5 55555555555 5555 555555555559 3 Introduction sonnnnnenenonononennnnererererrrrerrrrrererererereene 4 FMS 4 Hardware Overview rrarnnrrnrrrernerrnrnnrnurnnennrnnnnnsnnsee LES rae e E E E 5 COMMS 6 1 0 EEE NE 6 Hardware Installation axnnvnnrnnnnnnnnnnennnnnnnnnnnnnennennenn 7 Push Button Security secctes cect cusssautenametectacaseeeieaceses 8 Using the Setup Wizard ennrnnnnnnnnnnvnnennnnnnnnnnnnnnenn 11 OVATE RUN OU aces Ses sce ete eects 13 SetUp asrisataguausnareone 580 850 839 15 Slo 0 EEE 17 Application QOS rerernnnrrarerarerernnvenurerernnverunennenneen 18 Advanced QOS rrrarnnnnnnrnnnnnnrrnvnnnennenurnnnereeruneneeneen 19 SEE 20 Troubleshooting 5 5 5 5 5 55 5 555555555555 955 1 Technical 5866 8 0 5 22 D Link DHP 302 User Manual Section 1 Product Overview Package Co
8. f Service Me Application Gos for traffic passing through your l network E BitTorrent 21 Adopt Application QoS or Advanced QoS and then click Rule 1 Destination port 206 Priority pinned to f 581 882 883 584 885 586 B87 888 Ker applications use or fe E E UOP User 208 5 Datagram No prioritization Frotocohfor data transfer while database applications use TCP Transmissian Rule 1 priority is higher than Rule 2 Control Protocol for data transfer Save Settings version 1 0 Copyright 2009 D Link Inc All Rights Reserved Rule Select the traffic type UDP or TCP to have priority 802 1p use prioritization bits in Layer 2 frames Port Input the port number to have priority Priority Input port priority from 1 to 6 The highest priority is 6 and the lowest is 1 Note Rule 1 has priority over Rule 2 D Link DHP 302 User Manual 19 section 3 Configuration system D Link Powerline HD Utility D Link Powerline Setup Security QoS System Power Saving M Enable Power Saving Save Factory Reset Reset Upgrade Firmware Firmware Version D Link Powerline v1 00 Firmware File Browse 85161618 16128 881 2185 Version 1 0 Helpful Hints To enable power saving mode check the box and click button Click button to reset the node to initial factory settings All previ
9. k adapters reset the utility and start configuring the adapter again D Link DHP 302 User Manual 21 Appendix A Technical Specifications Network Ports e One 10 100 Ethernet port EMC e FCC Part 15 Class B e CE Class B e C Tick AC Input e 100 240VAC 50 60Hz Safety e UL 60950 D Link DHP 302 User Manual Technical Specifications Encryption e 3DES Operation Temperature e 0 C 40 C Storage Temperature e 10 C 70 C Humidity e Operation 10 90 RH e Storage 5 90 RH 22
10. ntents e D Link DHP 302 Powerline HD Ethernet Adapter e CAT5 Ethernet Cable e CD ROM with Software and Manual e Quick Installation Guide System Requirements e Windows Vista XP with Service Pack 2 or 2000 with Service Pack 4 e PC with 233MHz Processor 64MB Memory e Ethernet Adapter 100MBit s D Link DHP 302 User Manual Section 1 Product Overview Introduction D Link announces a fast 200Mbps Powerline HD Ethernet Adapter which allows you to network your home computers networking devices and gaming devices through the most pervasive medium in your house the electric powerlines and share Internet connections printers transfer files play games and more This kit can be used to network two Ethernet enabled devices with a 10 100Base T adapter through powerlines Features e Provides Ethernet to Powerline Connection e Fast Data Transfer Rate of Up to 200Mbps e One 10 100 Ethernet port e Plug amp Play Easy Installation e Easy to use Management Software e Configurable QoS for video streaming VolP and Gaming e Firmware Upgrade Support e Push button security e Throughput LED e Power Saving mode e LLTD Support Windows Vista D Link DHP 302 User Manual 4 Section 1 Product Overview Hardware Overview LEDs AP LED A solid light indicates that the device is the master unit in the powerline network Power LED A solid light indicates that the device is receiving power
11. ously defined settings will need to be re configured To upgrade the firmware click button and then locate the firmware file Finally click button to proceed With the power saving mode enabled and the ethernet link activity being down for 15 minutes the DHP 302 will automatically go into stand by mode When the master unit is in stand by mode the throughput LED will blink red intermittently To reset your configuration password please click Reset to restore the password to the factory default value D Link DHP 302 User Manual 20 section 4 Troubleshooting Troubleshooting Powerline HD utility does not start correctly Reinstall the utility Powerline HD utility does not detect the PowerLine HD Network Switch Please make sure your Powerline HD Network Switch is correctly plugged and connected to the computer or network device e can t configure any parameter of the PowerLine HD Network Switch an error is shown when I try to configure it Please make sure you have not unplugged the PowerLine HD Network Switch while configuring it e changed the connection cable to another Network adapter and now the utility does not work correctly Please restart the utility each time you disconnect the connection cable e Pm having a lot of problems configuring my network you are having many problems configuring the network with two or more PowerLine HD Network Switch please make a reset to all of the Networ
12. owerline network Use Default button Select to reset the Network ID to the default value D Link D Link DHP 302 User Manual section 3 Configuration Application QoS D Link Powerline HD Utility D Link 1e Liuality of service will allow Quality of service you to set priorities for traffic passing through your network Adopt Application QoS or Advanced Glos and then click C Advanced QoS Rule 1 no prioritization Y button Multimedia applications use UbP User Datagram ie No prioritization 2 Protocoljfor data transfer while database applications use TCR Transmission Rule 1 priority is higher than Rule 2 Control Protocol for data transfer Save Settings version 1 0 The Quality of Service QoS screen will allow you to set priorities for traffic passing through your network By default all types of traffic are assigned the same priority Multimedia applications use UDP User Datagram Protocol for data transfer while database applications use TCP Transmission Control Protocol for data transfer Application QoS Select an application from the drop down menu of predefined QoS rules to apply QoS automatically Click the Save Settings button to apply your settings D Link DHP 302 User Manual 18 section 3 Configuration Advanced QoS D Link Powerline HD Utility D Link Powerline Setup Security Qos System Aart at 1e duality of i Service will allow Quality o
13. twork security purpose The Network ID allows you to protect your network from Unauthorized Powerline network 14 section 3 Configuration Setup D Link Fowerline HD Utility D Link Powerline Setup Security QoS System Network Info O AutoScan Finished Device Name Network ID MAC Location Quality Version 1 0 This screen shows the current configuration of the DHP 302 Helpful Hints The assistant has detected the following nodes In the electric network If you think more nodes should be shown make sure the nodes are connected and click button Check box to scan all nodes within the network periodically For better signal strength plug the device directly into a wall outlet avoiding the use of power strips and extension cords Device Name Show name of devices that have been discovered Default is Device 1 Device 2 etc Max 16 characters 0 9 A Z case sensitive ie Living room Bedroom etc Network ID Powerline Network Name The default ID is D Link Max 10 characters 0 9 A Z case sensitive MAC MAC Address of detected node Location Local or Remote nodes D Link DHP 302 User Manual 15 section 3 Configuration Quality Network connection quality of the connected node e Three circles Best powerline connection Suitable for HD video stream connection e Two circles Better powerline connection Suitable for SD video stream connection e One circle
Download Pdf Manuals
Related Search