Untitled
Contents
1. measurement limit To pull backwards can make the meter remove from the 11 lead on teat as shown in Figure C please try to keep the meter transducer domain perpendicular to the lead when moving away Measuring HV Current Measuring LV Current Under HOLD mode press HOLD button to cancel HOLD function and return to normal testing mode Under data reference mode press POWER button for more than 3 seconds to exit from data reference mode returning to normal testing mode Under PEAK testing mode press POWER button to exit from PEAK testing mode returning to normal testing mode After data deletion it will return to normal testing mode automatically Attention For the sake of safety when test has A been finished please remove the meter away from the lead on test 12 3 PEAK Test PEAK test the maximum current test The meter will make automatic comparison on the changes in measured current indicating the maximum value and maintain it when the meter is removed away from the lead on test the test result will be kept consistently suitable for the circuit test on those LCD data hard to be read directly Under the normal testing mode press PEAK button PEAK indication light will be bright enter PEAK testing mode That means the meter will display and automatically keep the maximum valu2. Storage Temperature 10 C 60 C Below 70 Rh and Humidity e 32mm 1m Section 5 Sections imension Insulation AC 100KV rms Between insulation rod and Intension clamp core Structure Anti Dripping Type II V Structure 1 Double input toroid including the boot area 2 ETCR9000 Tester 3 LCD Display 4 PEAK Test Indication 5 PEAK Key 6 POWER Key 7 HOLD Key 8 ETCR9000B Receiver 9 Insulation Rod Connector 10 POWER Indication 11 ETCR9000B Testers ey iS A A E H L VOLTAGE CLAMP METER ue VOLTAGE CLAMP METER BIS AR REPEINER 4 lt _ _ te a e 6 TQ O ey T_ lay ETCR9000 ETCR9000B 9000B Receiver VI LCD Display 1 LCD Display Screen D 3 4 6 1 AC symbol 2 Low battery symbol e e ES Es a Pee 3 Date storage symbol 9 mn Fl a a 6 4 Date access symbol 8 shala m lL IQ 5 2 digit storage data serial number pe 6 Unit symbol 7 Date locked symbol 8 Decimal system radix point 9 4 Digit LCD digital display 2 Explanation for Special Symbols 1 Eh Low battery symbol when the voltage of battery is lower than 4 8V this symbol display please replace battery in time 2 OL A This symbol indicates that the current on test has exceeded the maximum measurement limit of the meter 3 MEM Memory mode it will display during the data storage process 4
3. accident Dangerous The operator must strictly abide by the safety rules Otherwise there is electric injury danger causing personal damage or casualty accident Warning It must strictly abide by the safety rules Otherwise it may cause personal damage or casualty accident Alternating Current AC Direct Current DC lll Series Model Range of Jaw Model Accuracy Description measurement Specification ETCR 9000 0 0mA 1000A 0 1mA 48mm base ETCR 9000B 0 0mA 1000A 0 1mA 48mm wireless IV Technical Specification High voltage AC current measurement low Function voltage AC current leakage current measurement on line AC current supervision Power Supply DC6V Alkaline Dry Battery 1 5V AAA X 4 Test Method Clamp CT Integral Method Transmission B Model Wireless Transmission the maximum Method distance for direct transmission is about 30m P 4 digital LCD display backlight function Display Mode suitable for dark place E ECO 47mmx28 5mm imension ena W H T 76mmx255mmx31mm imension Clamp Diameter peer Sampling About 2 times second Speed Range of o 0mA 1000A 50 60Hz Auto Identification measurement Resolution 0 1mA Shift 0 0mA 1000A Automatic Shift 0 0mA 299mA 1 3dgt Test Accuracy 0 30A 49 9A 1 5 5dgt 23 C 45 C 50 0A 199 9A 2 0 5dgt Below 80 RH 0094 6004 4 3 5dgt 601A
4. danger causing personal damage or equipment damage Dangerous It cannot be used to measure the circuit over 1000A voltage Otherwise there is electric injury danger causing personal damage or equipment damage General Test In the process of test LCD will display the tested current value real time and LCD data will vary with the current change When the tester is removed away from the lead on test it does not preserve the test result LCD display will return to zero In normal testing mode it is suitable for close distance measurement convenient for circuit test by direct read of LCD data Before test firstly to connect insulation rod which must be connected in right position and then to connect tester avoiding the impact of meter to ground surface Make sure to use specially equipped insulation A rod to connect with the meter After test it should incline the insulation rod accordingly on drawing in Firstly to tear down the tester and then the insulation rod avoiding the impact of meter to ground surface After normal boot place the lead in the middle of clamp transducer domain as shown in Figure A with the meter transducer domain perpendicular to the lead pushing the meter forwards to clamp the lead on test showing the result on LCD display If showing OL A it means the lead current on test has exceeded the maximum volume on the level Please select a higher gear level or a meter with greater
5. s data in storage Press HOLD button to exit from data reference mode returning to normal testing mode During the exit it will display End symbol Data Deletion Under data reference mode press PEAK POWER button to delete all the data in storage and return to normal testing mode During the deletion of data it will display dEL symbol Data Transmission B Type has the function of wireless data transmission When the Meter under testing mode the test result will be transferred to receiver by wireless transmission and the receiver will display test result real time being clear at a glance Only under testing mode the meter will transmit If the receiver has not received emission signals it will display no symbol dynamically B Type Transferred ETCR9000B Type Wireless transmission test data a straight line distance of about 30 meters can penetrate the floor to receive data B Operation of Receiver Note For ETCR9000B only 1 Power On Off Press POWER button to power on the instrument will displays the LCD screen entering normal testing mode If LCD display is relatively dark after power on it is possible that battery voltage is a bit lower Please replace battery 15 minutes after powering on the meter if it remains idle an auto power off procedure starts to preserve the battery life and LCD will continue flash until the complete switch off takes p
6. the cover board to replace brand new qualified batteries on It should pay special attention on the battery specification and polarity cover the board well and fasten the two screws 3 Press POWER button to check whether the meter can be powered on normally If not please repeat the operation according the step 2 16 Battery cover Battery cover Loosen Tighten RE O O O O IX Accessories Tester 1PCS Receiver ETCR 9000B special 1PCS Insulation Rod 1M Section 5 Sections Meter Box 1PCS i 4 PCS or 8 Battery Alkaline Dry Battery AAA PCS User s Manual Maintenance Card SET Conformity Certificate 17 A Manufactured by ETCR Electronic Technology Company Address F 3F No 4 Pengshang Zhifu Road Jiahe Baiyun District Guangzhou Guangdong China Post Code 510440 Tel 86 20 62199556 62199554 Fax 86 20 62199550 E mail info etcr cc Website www etcr cc
7. 1000A 4 5dgt 99 Groups during storage the symbol MEM Data Storage gives indication FULL mark will flash to indicate the memory has been full Circuit Voltage Peak Test for the circuit below 60KV operated with insulation rod Automatically maintain the height of the test ES Maintenance value usually in the test mode press PEAK key PEAK lights that is to keep open the PEAK function then press PEAK key to cancel this function Data Preservation Under general test mode press HHOLD button to preserve data HOLD symbol display then press HOLD Key to cancel this function Data Access MR symbol indicates it can read the stored data by turning upwards and downwards Overflow Exceed measurement range overflow function Display OL A symbol display No signal When the receiver has not received transmit Indication signal it will display no symbol About 15 minutes after booting the meter will i shut down automatically in order to decrease the battery consumption Battery Voltage When the battery voltage is below 4 8V the symbol of battery voltage EH will show to remind to replace battery Tester About 335g Including battery total Weight quality of meter about 2 5Kg including insulation rod and battery Work Temperature 10 C 40 C Below 80 Rh and Humidity
8. ETCR HLVOLTAGECLAMP METER ETCR 9000 ETCR 9000B Guangzhou ETCR Electronic Technology Co Ltd CONTENT Warming tas ail ed oni eae ents 1 LAB SP OURO GUC OI st ista 3 ll Electrical SYMONS rca 4 Hh Series Mode econ 4 IV Technical Specification nacido te 5 NU a 7 Mi LCR DI dd 8 VIL Operation isa 10 A Tester Oporto dae Eo o des de ta to o Lu Da La To Eo 10 1 POwer OnO arroetan a e r r ar 10 2 General Teta AR 10 3 PEAK Te ia 13 4 Data A A 13 Di Data MCmory s ceisessdosceds sdeseues irrita led dad decia siesta n ES 13 6 Data Reverence a a e nein then sei a eaten te ataness 13 7 Data Deli 14 63 5 Data TransmissiOnssiit ch te thsaes ote cts te hens gute cate ahanes A gedhensh ance ease teen 14 B Operation of RCC hacks cizsciencsesssesdseatensseassenscvacseendunstanceaaceesdinds 14 ko Power OVA 14 Z Data Recopa 15 Biv Data Manten decidi 15 gt Data Memory TN 15 5 Data Reference 6 Data Deletion VIII Replacing Batteries IX Accessories A Warning AN Thanks for your purchase of ETCR9000 H L Voltage Clamp Meter of our company In order to make better use of this product please make sure to Read this manual in detail and the operator must totally understand this manual and be in proficient in operation of this meter before making test on spot Sirictly comply with the security rules and notice items l
9. Full symbol when the storage memory has been filled with 99 groups of data it will display FULL symbol by flash which means it cannot continue to store data 5 MR data access symbol which is displayed during looking up data meanwhile it will display the serial number of data in storage 6 End exit symbol it will display during the exit 8 7 dEL data delete symbol it will display when deleting data 8 no None received signal instructions dynamic display it may not in test mode or adjust the location and distance from receiver 3 Display Demonstration 1 The current on test is 0 002A 2mA 2 Locked display Data The data is automatic stored as group 3 The current on test is 160 5A 3 The current on test is 571A Low battery symbol please replace 4 Look up data of group 3 in storage The current on test is 160 5A 5 FULL flash display Storage is full of 99 groups E lt can t store more unless delete storage 6 dEL Indication of data delete 1 End Indication of exit 8 no Dynamic display none received signal Vil Operation Please check all parts of the meter carefully before usage to see whether there is any uN damage And make sure no damage before usage According to manual instructions to install the battery A Test
10. e in the test Under any other mode it must be returned to normal testing mode and then make PEAK testing according to the above operation Press POWER button to exit from PEAK testing mode returning to normal testing mode and it will display End symbol during the exit 4 Data Maintenance Under normal testing mode press HOLD button to keep LCD display HOLD symbol displays Press HOLD button again to release data lock returning to normal testing mode and HOLD symbol disappears 5 Data Memory Under normal testing mode press HOLD to storage data at the same time Meter will automatically form serial numbers and memory the current preserved data During the storage MEM symbol will show once by flash This meter can memory 99 groups of data in case of full storage FULL symbol will display by flash continuously and it cannot continue to memory until cleaning out the previous memory 6 Data Reference Under normal testing mode press PEAK POWER button to enter data reference mode displaying MR symbol meanwhile it will automatically display data saved in the group 01 Then press PEAK or POWER button to read the stored 213 8 data by turning upwards or downwards in cycle It will return to the group 1 s data automatically after reaching the last group
11. er Operation 1 Power On Off Press POWER button to power on the instrument will displays the LCD screen entering normal testing mode If LCD display is relatively dark after power on it is possible that battery voltage is a bit lower Please replace battery 15 minutes after powering on the meter if it remains idle an auto power off procedure starts to preserve the battery life and LCD will continue flash until the complete switch off takes place after 30 seconds In case of LCD continuous flash press POWER button then the meter will continue to work Under HOLD mode press POWER button for power off Under general test mode press POWER button to power off Under PEAK testing mode press POWE button to power off Under data reference mode firstly press POWERI button for more than 3 seconds to exit from data reference mode returning to normal test mode then press POWER button to power off During the exit from data access it will display End symbol 2 General Test High voltage extremely dangerous It must be operated by qualified staff that has acquired authority The operator must strictly abide by the 10 safety rules Otherwise there is electric injury danger causing personal damage or casualty accident Dangerous It cannot be used to measure the circuit over 35KV voltage Otherwise there is electric injury
12. erence mode MR symbol display meanwhile it will automatically display data saved in the group 1 Then press HHOLD button or POWER button to read the stored data by turning upwards or downwards in cycle It will return to the group 1 s data automatically after reaching the last 15 group s data in storage Press POWER button for more than 3 seconds to exit from data reference mode returning to receiving data mode During the exit it will show End symbol 6 Data Deletion Under data reference mode press HOLD POWER button to delete all the data in storage and return to Data Reception mode During the deletion of data it will display dEL symbol Vill Replacing Batteries Warning In case that the battery s cover N board is not well closed it is forbidden to make test Otherwise it is dangerous Pay attention to the polarity of battery in case of damage to the meter Do not mix in the use of new and old batteries 1 When the battery voltage is below 4 8V the meter will display Ep symbol indicating the batteries have no sufficient power content Please replace batteries 2 Power off to make sure the meter is under the state of power off To loosen two screws of the battery cover board open
13. isted on this manual In any case it should pay special attention to safety in use of this meter particularly in measurement of circuitry with more than AC100V and above voltages If the voltage of tested circuitry has exceeded 600V it must be used by connecting with an insulation rod As it is very dangerous of high voltage transmission line the operator must get strict training and the relevant certification on high pressure operation of the state before using this meter and making a field test It is strictly forbidden to use this meter to test the wire without any insulate protection has voltage exceed 35KV or convergence generatrix Please pay attention to marked words and symbols on panel or backboard of this meter Please do not put or store this meter in the place of high temperature with moisture with frozen dew or with direct daylight irradiation for a long time Please note the battery polarity when replacing battery and remove the battery if you expect not to use this meter for a long time It must be operated by qualified staff that has the authorization on tearing down or repairing this meter Please do not use it when there is any damage on the Ts transducer clamp or other parts of this meter To avoid the impact of transducer clamp it needs to maintain this meter regularly Do not use corrosive or coarse materials to clean but use soft cloth such as glasses cloth dipping clean anti rust desiccant lubricant s
14. lace after 30 seconds In case of LCD continuous flash 14 press POWER button then the meter will continue to work Under HOLD mode press POWER to power off Under data reference first press POWER button for 3 seconds to exit data reference mode then come back to data receive mode press POWER button once again to power off During exit from data reference it will display the symbol of End Data Reception After normal power on the receiver will under receiving mode lf there are emission data the receiver will display the test result real time If it has not received any signal the receiver will search signals constantly and display no symbol dynamically Data Maintenance Under Data Reception mod press HOLD button keep LCD display HOLD symbol indication Press HHOLD button once again to relieve data lock return to data reception mode HOLD symbol display Data Memory Under Date Reception mode press HHOLD button to maintain data meanwhile the receiver will automatically form serial numbers and memory the current preserved data During the storage MEM symbol will display once by flash The receiver can memory 99 groups of data in case of full storage FULL symbol will display by flash continuously and it cannot continue to memory until cleaning out the previous memory Data Reference Under Data Reception mode press HOLD POWER button to enter Data Ref
15. ter has an innovative integrated design between transducer clamp and transducer domain ensuring the high precision high reliability and high stability on constant test perennially ETCR9000 Series H L Voltage Clamp Meter is connected with insulation rod which can be used for measuring high voltage current that is below 60KV on line current measurement also having peak maintenance data preservation data storage wireless transmission and other functions and its special clamp meter can make it easier for clamping or evacuating the tested wire through pressing or pulling back the insulation rod time saving and fast widely used in transformer substation power plant industrial and mining enterprises as well as the inspection station and electrician maintenance departments for electrical current detection and field electrical operations It can also replace the H L voltage transforming ratio tester that is to detect the high and low current for primary circuit and secondary circuit separately and then calculate to conclude the change of high and low pressure The insulation rod is light and convenient with the advantages of anti moisture high temperature resistance anti impact bending resistance high insulation flexibility and other characteristics ll Electrical Symbols N Extremely Dangerous The operator must strictly abide by the safety rules Otherwise there is electric injury danger causing personal damage or casualty
16. uch as WD 40 and making a gentle wiping For the reason of this meter in case that any danger may occur if continue to use it stop using it immediately and seal it up for keeping at once which shall be dealt with by qualified authorization agency The danger symbol on the meter and the manual the user must make safe operation according to the indication The extremely dangerous symbol the user must make safe operation according to the indication It suggests that this meter shall be made insulation intensity test at least once annually AC 100kV rms between insulation pole and clamp core As to the part with mark in this manual it is only limited to ETCR9000B type wireless Transmission data type Brief Introduction ETCR9000 Series H L Voltage Clamp Meter has broken through the traditional structure which is specially well designed for measuring high voltage current adopting the latest CT technology and integrated mask digital technology formed by composition of a special use clamp meter with a high voltage insulation rod as to ETCR9000B type wireless transmission of test data it is equipped with wireless receivers which can receive measured data within 30 meters line If not using an insulation rod it can be also used as a high precision low voltage clamp meter or an alternating current meter which can accurately measure 0 1mA of current or leakage current ETCR9000 Series H L Voltage Clamp Me
Download Pdf Manuals
Related Search