Magic Touch - Touch Screens Inc.
Contents
1. 14 KTMT 1500 and KTMT 154W do not have hangers Controller is either a box or a board SB model with USB cable USB XD or serial cable ProE X 0 0 1 0 1 1 1 1 1 3 92 2 3 ri 3 OOO 3 Magic Touch Add On Kits KTMT series mounting 3 1 1 Open the cover Remove the protective film on the touch screen and mount the touch screen to the notebook using the Velcro straps picture 1 3 1 2 Buckle the horizontal straps to the back of the notebook picture 2 and pull the two vertical straps down and adhere them to the horizontal strap picture 3 3 1 3 Continue to B Controller amp Driver Installation 3 2 KTMT for monitors KTMT 1315 1700 1900 and 1921 3 2 1 For Mounting on LCD monitor There are two sets of hangers included one pair of hard plastic hangers and one pair of Velcro hangers 3 2 1 1 You may use the plastic hangers Place the touch screen panel on a flat table with the backside facing up Screw two hangers into the back of the panel using the top screw holes on the hanger picture 1 3 2 1 2 Adhere two Velcro strips provided on the top of the display as indicated by the arrows in picture 2 Mount the touch screen to the display picture 3 3 2 1 3 If you find the top of the touch screen is blocking the view area of the display you may raise the touch screen by adding the rectangular foam pad underneath the hangers picture 4 3 2 1 4 Alternatively you may use the Velcro hangers pictur2. M agc T aun User s Manual Installation Instructions CONTENTS A Touch Screen Panel and Touch Monitor Installation 1 Introduction 2 Parts list 3 Magic Touch Add On Kits KTMT series mounting 4 Magic Touch Monitor KTSC KTLC series connection 5 Magic Touch Built In Kits KTT series integration B Controller and Driver Installation 6 USB XD controller Win Vista XP 2000 ME 98 Mac 9 2 2 10 5 x Linux 7 ProE X controller Win Vista XP 2000 ME 98 95 NT 4 0 Linux Note Not all the drivers are included Windows multi monitor and Linux drivers and installation procedures are included on the CD 8 Settings and Options 9 Touch Screen Functions C Important Information 10 Helpful Notes 11 How to take care of your Magic Touch products 12 Troubleshooting amp Technical Support 13 Warranty information amp Return Policy KEYTEC INC www magictouch com FCC COMPLIANCE This equipment has been listed and found to comply with the limits for a Class B digital device pursuant to Part 15 Subpart B of FCC Rules This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions it may cause interference to radio communications The limits are designed to provide reasonable protection against such interference in a residential situation There is no guarantee that interference will not occur in a par
3. _xd html Multi Monitor setup and examples are under the folder MultiMonitor driver Mac driver CD is included only if you have ordered Mac version USB M or USB WM extra charge applies Mac user please see Sec 6 3 for instructions Linux user please see readme file in Linux folder for setup instructions 6 1 For Windows Must logon with administrator s password for Vista XP 2000 6 1 1 Vista If you prefer to use Vista s embedded tablet driver DO NOT install Magic Touch driver from the CD If you have already installed it you must uninstall it first Plug in the USB controller Windows will find new hardware The screen should respond to your touch but the position may not be accurate If you use ProE controller plug in the controller before the computer is turned on 6 1 2 Calibrate Vista tablet driver 6 1 2 1 Right click the desktop select New gt Shortcut 6 1 2 2 In the field Type the location of the item key in the following phrase windirY system32 tabcal exe NoValidate then click next Note it is important to key in the exactly same phrase with space after tabcal exe and make sure that the N and the V are capitalized and that there is no space between No and Validate 6 1 2 3 In next window click Finish and you will now have a shortcut on your desktop labeled tabcal exe 6 1 2 4 To calibrate you can click and run the tabcal shortcut on the desktop to launch the ca
4. and options to the original settings 9 Touch screen functions 9 1 Screen touched left mouse button clicked 9 2 Touch down and drag left mouse button held down and dragged 9 3 Tap twice left mouse button double clicked 9 4 Swap Button Select once to right click on next touch only or always to right click on every touch Select minimize to reduce to system tray as a shortcut C Important Information 10 Helpful Notes 10 1 Place the monitor at an easy to touch position and avoid direct strong lighting to reduce glare on the screen 10 2 It is easier to use the stylus for clicking smaller icons dragging and drawing apply constant pressure when drawing 10 3 Make one point touch only Do not lean your hand on the screen or touch it with more than one finger or stylus 10 4 Increase the size of icon and menu bar for easy touch 10 5 If double click is difficult change to single click in Tools Folder Options 11 How to take care of your Magic Touch product 11 1 DO NOT touch the screen with hard sharp objects 11 2 DO NOT hit or drop the screen 11 3 DO NOT spray any liquid directly to the screen Clean the screen with soft cloth or paper towel dampened with cleaning solution such as Windex alcohol 11 4 DO NOT alter or substitute any parts 11 5 Put the screen into the original packaging for storage and transportation Failure to handle and use this product properly will negate the
5. ave different housing design and wiring connections The following procedures should be used for reference purpose only 5 1 Important Test both touch screen panel and monitor before the installation 5 2 Open and remove the housing of the monitor check with your monitor supplier about the warranty policy regarding to this step 5 3 Clean the monitor surface and the back of the touch screen panel remove the protective film of touch screen 5 4 It is very important to center the touch screen panel to the opening of the monitor s front frame so that the edges of the frame will not contact the active area of the touch screen to prevent shorts caused by constant touching pre load The edges of the frame should rest on the clear insulation border of the touch screen Depending on the structure of the frame foam strips and washers may be needed to add space for preventing shorts 5 5 For service purpose the touch screen should be removable from the monitor Therefore it is not recommended to use double side tape or permanent adhesive to mount the touch screen on top of the display Use high temperature ducking tape to mount the edges of the touch screen to the metal frame of the display Add support at the bottom of the touch screen to prevent it from sliding down 5 6 If the monitor does not have enough space to accommodate the thickness of the touch screen do not force the housing to close because it may damage both the touch scree
6. cessary Click OK to close the window 6 1 3 8 See 8 Settings and Options 6 2 For Macintosh with USB port a quick guide file is included in the CD Plug in the controller to USB port and plug in the touch screen cable to controller 6 2 1 Insert the installer CD Double click to open the Magic Touch CD icon 6 2 2 There are 6 folders for OS 9 2 x 10 1 x 10 2 x 10 3 x 10 4x and 10 5x 6 2 3 Open the folder that matches your OS version see Apple gt About this Mac 6 2 4 Double click MagicTouch icon to run installation If a LOCK icon appears on the lower left corner click and type in the administrator s password 6 2 5 After installation is completed restart the computer 6 2 6 Calibrate the screen For OS 10 x click Go Application Magic Touch Utility Magic Touch For OS 9 x click Apple Control Panel Magic Touch Utility Magic Touch Before entering the calibration screen you will be prompted for lift off mode selection This appears as a checkbox in OS X In lift off mode the mouse click is activated when touch is lifted from the screen Please see quick guide for details Once the selection is made the calibration screen is shown OS X Press calibrate Touch the centers of the 3 Xs with stylus provided for better accuracy to complete the calibration Check the accuracy repeat if necessary Press cancel to exit Note Although the Windows driver CD is normally not included with the touch screen sold as Mac ver
7. e 5 The soft surface of the Velcro faces up when fastening them with the screws to the frame Mount the touch screen to the display and press the Velcro firmly picture 6 3 2 1 5 Must apply the Velcro at the bottom of the screen picture 7 to secure the mounting Use the cable clips to secure the touch screen cable picture 8 Continue to section B Controller amp Driver Installation 3 2 2 For mounting on CRT monitor 3 2 2 1 Measure the top frame of the monitor picture 1 If it is 1 5 inches 3 8 cm or less use the top holes on the plastic hangers to screw into the touch screen panel Otherwise use the bottom holes 3 2 2 2 Place the touch screen panel on a flat table with the backside facing up Screw two hangers into the back of the panel picture 2 3 2 2 3 Hang the touch screen onto the monitor in center position Use a pencil to mark the hangers position on top of the monitor picture 3 3 2 2 4 Remove the touch screen from the monitor Adhere two pieces of Velcro strips provided onto the top of the monitor near the pencil marks picture 4 3 2 2 5 Mount the touch screen panel as close to the monitor as possible with the hangers aligned to the Velcro strips picture 5 3 2 2 6 Press down the hangers firmly to fasten the Velcro strips picture 6 3 2 2 7 Adhere the Velcro at the bottom center of the screen picture 7 3 2 2 8 Adhere the 3 cable clips to the side of the monitor to organize and secu
8. l Office mabel magictouch com Tel 02 2921 0121 Fax 02 2921 1375 Tokyo NDS sales nds jpn com Tel 048 956 0730 Fax 048 956 8885 London Interactive Ideas sales interactiveideas com Tel 44 020 8805 1000 Fax 44 020 8805 8962 Munich Electrade info electrade com Tel 49 089 898 1050 Fax 49 089 854 4922
9. libration utility Use the stylus supplied to perform calibration for better accuracy Touch the center of the cross and release Do not hold Complete the 4 point calibration Recalibrate if necessary 6 1 3 Install Magic Touch driver on Windows OS 6 1 3 1 Insert the setup CD The setup window will display on the desktop Click to select USB controller Then click Install Vista may require your permission to allow setup to run Note If setup window does not open the CD Rom s autorun may be disabled Click START RUN to run the setup from the driver CD 6 1 3 2 For Win XP amp 2000 When the system prompts please plug in the Magic Touch USB to USB port plug in the controller After Windows has found the new hardware click OK to continue 6 1 3 3 When must reboot Windows to complete the installation shows click OK to reboot For Win 98 amp ME plug in the controller after reboot 6 1 3 4 After Windows is rebooted two new icons are created on desktop N Touch USB p Swap Button k 6 1 3 5 Double click Touch USB icon to open touch control panel 6 1 3 6 Click the Calibration button choose either 5 or 25 point calibration and click GO To calibrate touch and hold the center of each circle for a full second before lifting your finger The circle will then progress to the next one until all 5 or 25 have been touched Use the stylus to perform calibration for better accuracy 6 1 3 7 Repeat the calibration if ne
10. n and monitor Do not force the mounting screws beyond finger tightness Note Slim LCD and notebook computers usually are not suitable for touch screen integration 5 7 Pull the touch screen cable out from the back of the monitor Replace the connector if necessary make sure the wiring is correct Note If the cable is not long enough contact KEYTEC for a custom extension cable Regular telephone cable cannot be used for extension Continue to section B Controller amp Driver Installation B Controller and Driver Installation There are two types of controller box USB XD amp ProE X as labeled on the controller The SB model controller does not have a box The USB XD The ProE X controller should m controller should be plugged into a be plugged into the USB port aa the serial port when instructed s a Com or 2 when by the driver eS the computer is installation steps powered off For notebook add on connect Connect controller Plug the touch screen the curly cable to touch screen to computer as cable into the controller with white dots aligned instructed above box 6 USB XD controller Win Vista XP 2000 ME 98 Mac 9 2 2 10 4 x Linux lf there is a previous Magic Touch driver or other manufacturer s touch screen driver installed in your system uninstall them first All Windows and Linux drivers are included on one CD and can be downloaded at www magictouch com support usb
11. nt calibration then click GO Touch and hold the center of each circle for a full second to complete the calibration Use the stylus for better accuracy Repeat the calibration if necessary Click OK to close 7 7 To use Vista s embedded driver please refer to 6 2 3 8 Settings and Options of Magic Touch Control Panel Windows version 8 1 Mouse speed Control the tracking speed of mouse cursor 8 2 Double click speed Control the time interval between two clicks to activate a double click Slow speed makes double click easier Test the double click by tapping the K logo twice If successful the logo rotates 8 3 Lift Off When this option is enabled the click is activated when touch is lifted away from the touch screen This mode is very useful for clicking hyperlinks such as Internet browser or programs that use mouse over function However it is impossible to drag or draw in this mode available in Mac version 8 4 Beep Enable disable an audible beep when a touch is sensed Customize the beep s pitch and duration under Beep Options 8 5 Move only Touching and dragging moves the mouse cursor without performing a click This is only for an optional click pen currently unavailable 8 6 Hide cursor Makes the cursor invisible preferred for some applications 8 7 Uninstall Click to uninstall the driver Correct password needed magictouch is the default password 8 8 Default setting Return the speeds
12. re the cable This can also help prevent the screen from impacting the ground should it be knocked off of the monitor picture 8 It is VERY IMPORTANT to follow the above procedures to avoid accidental damage Continue to section B Controller amp Driver Installation 4 Magic Touch Monitor KTSC amp KTLC series connection 4 1 Connect the monitor to computer as instructed in the monitor s manual which typically involves the power cord and video cable connection Ignore any contents pertaining to touch screens in the monitor s manual 4 2 Connect the touch screen cable from the back of the monitor to the controller Note If the cable is not long enough contact KEYTEC for a custom extension cable Regular telephone cable cannot be used for extension Continue to section B Controller amp Driver Installation 5 Magic Touch Built In Kit KTT series integration Built in kits must be integrated by experienced technicians The integrator will be solely responsible for any damage to the monitor and touch screen kit Physical damage to the touch screen is not covered by the warranty For all standard LAM and CAF1 models the flex tail should be on the left and its alignment mark white dot should match the one on the extension cable The display needs to have minimum of 3 mm or 1 8 space inside for touch screen integration It is impossible to provide a general guideline for integration because different monitor models may h
13. sion the user can download all Windows and Linux driver at www magictouch com support usb _xd html for free 7 ProE X Controller for Win Vista XP x64 2000 ME 98 95 NT4 0 Linux If there is a previous Magic Touch driver or other touch screen s driver installed in your system uninstall them first All Windows and Linux drivers are included on one CD and can be downloaded at www magictouch com support_proe x html For NT 4 0 amp Linux user please see readme file for setup instructions Note MUST logon with administrator s password for Vista XP 2000 amp NT 4 0 7 1 Insert the setup CD The setup window will display on the desktop Click to select ProE controller Then click Install Vista may require your permission to allow setup to run Note If setup window does not open the CD Rom s autorun may be disabled Click START RUN to run the setup from the driver CD 7 2 When must reboot Windows to complete the installation shows plug in the ProE controller to a free Com port click OK to reboot Free Com port means there is no other device configured to use this Com port 7 3 Win XP 2000 After reboot the Detect New Hardware Wizard opens Click next and continue anyway at Digital Signature prompt 7 4 Two new icons are created on desktop I Touch RS232 T Swap Button 7 7 7 5 Double click TouchRS232 to open touch control panel 7 6 Click the Calibration button choose either 5 or 25 poi
14. ticular installation CE and RoHS COMPLIANCE This equipment has been tested analyzed and found to comply with CE and RoHS requirements DISCLAIMER The material in this document is for an informational purpose and is subject to change without notice The manufacturer assumes no responsibility for errors or omissions in this document Nor are any liability assumed for any damages from the use of this product and the information contained in this document All mentioned product names herein are registered trademarks of the respective companies All rights reserved No part of this document and the software provided with the product may be reproduced or modified without permission of the manufacturer Revision M 050808 A Touch Screen Panel and Touch Monitor Installation 1 Introduction Please identify the Magic Touch model you purchased Check all the parts in the package against the following parts list Follow the installation instruction only for your specific model NOTE Please read the instructions carefully Improper installation may cause permanent damages which may not be covered by the warranty 2 Parts List Add On Touch Monitor Built In KTMT KTSC KTLC KTT External touch screen 1 Hangers amp accessories set 1 Integrated touch monitor 0 Internal touch screen 0 Magic pen stylus 1 Cleaning cloth 1 User s manual 1 Installation CD 1 Warranty card 1 Controller 1 1 Notebook models KTMT 12
15. warranty 12 Troubleshooting amp technical support Troubleshooting guide is on the driver CD except for Mac version and also available at www magictouch com troubleshooting main html Request support online at www magictouch com techsupport html or send e mail to tech magictouch com Please include the information about Magic Touch model driver version installed your operating system and the nature of the problems encountered You may also call 972 272 7555 9 5 M F Central Time or contact your local authorized dealer for assistance 13 Warranty Information amp Return Policy Warranty information can be found on the driver CD and also available at www magictouch com warranty html Register to activate your warranty online at www magictouch com WarrantyReg html or mail in the registration card If you need to return the product you must first contact KEYTEC S tech support amp RMA department to get a return authorization number RMA Please email to tech magictouch com or call 972 272 7555 The product must be packed with sufficient protection insured for full value and shipped with freight prepaid lf the product is purchased from a KEYTEC dealer please check with your dealer directly about their return policy Sales amp Services Contact Information USA HQ KEYTEC INC sales magictouch com tech magictouch com Tel 1 800 MAGIC 89 or 972 272 7555 Fax 972 272 7501 Taipei KEYTEC INC ASIA TAIWAN Regiona
Download Pdf Manuals
Related Search