6262/6262-212/6260/6260-212 User Manual
Contents
1. Luige THE SOO Or VANES 6262 6262 212 6260 6260 212 User Manual www bugera amps com Important safety instructions m zA SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION High voltage Risk of death High voltages of up to 500 V DC may be present inside the casing for long periods after being disconnected from the mains To avoid lethal electric shock do not open the casing There are no user serviceable components inside Refer all maintenance to qualified service personnel Remove the mains cable when the unit is not in use WARNING To eliminate the risk of fire and electric shock do not expose this unit to rain or moisture and splashing or dripping liquid which might enter the device Do not place any objects filled with liquid such as vases on the unit This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instruc N tions in the accompanying literature Please read the manual 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do no2. features separate MID controls for the LEAD and CLEAN channels 9 The passive BASS control adjusts the lower fre quency range The 6262 and 6262 212 features separate BASS controls for the LEAD and CLEAN channels 10 This GAIN control specifies the input level of the LEAD channel Turn the control to the right to in crease the preamplifier s distortion and sustain The LEAD switch activates the LEAD channel switch glows red The CRUNCH switch activates the gain boost on the CLEAN channel switch glows yellow This way the CLEAN channel can be used as a second LEAD channel 11 12 This GAIN control specifies the input level of the CLEAN channel Turn the control to the right to in crease the preamplifier s distortion and sustain Please note that extremely high GAIN settings in conjunction with extremely high VOLUME settings can make the combo models vibrate mechanically This may occur when played at extremely high volume levels which is seldom done Should this be the case adjust the GAIN and VOLUME settings so that the problem does not recur The CLEAN switch activates the CLEAN channel switch glows green You can also activate both channels with the supplied footswitch Refer to Footswitch for details The BRIGHT switch activates an extra boost in the high frequency range 6 dB at 2 kHz which only affects the CLEAN channel The LOW GAIN input is used for instruments with an extremely h
3. SOUL OF VALVES mentioned belong to their respective owners and such use neither constitutes a claim of the trademarks by RED CHIP COMPANY LTD nor affiliation of the trademark owners with RED CHIP COMPANY LTD RED CHIP COMPANY LTD accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colors and specifications may vary slightly from product Our Products are sold through authorized dealers only This manual is copyrighted No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of RED CHIP COMPANY LTD BUGERA products are distributed exclusively by the BEHRINGER Group of companies globally and specifically by BEHRINGER International GmbH in the European Union ALL RIGHTS RESERVED c 2008 RED CHIP COMPANY LTD Trident Chambers Wickhams Cay P O Box 146 Road Town Tortola British Virgin Islands Limited warranty 11
4. damaged liquid has been spilled or ob jects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 17 CAUTION These service instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instruc tions unless you are qualified to do so 18 CAUTION During use the valves get very hot and high surface temperatures may be reached at the rear of this unit To avoid burning yourself make all connections while the unit is still cold Table of contents IMPORTANT NOTICE Pss EIIRGUA KO NEKEEN EREA ARA NEARNE 4 IntrOdUucLIOD ocasavesxasuvaSacsus cxvxewi2982u9 PEU VEEEKEEF DIU d Before you get Stel E 4 EELER 4 Belg de RTE ET EE 5 ONE EE 5 RO DAC EE 6 FOOLS Vy EC nena tau ERU 6 Insipe She BU ERA svp 5 45 54115 nano EE 7 Instructions Tor qualified Service De EDERT EEN 7 Wiring the BUGER A WEEN 8 Audio CONNECTIONS ER 9 RT erh e Le Vu EE 10 Limited Warranty EE 11 IMPORTANT NOTICE FAILURE TO OBSERVE THE FOLLOWING POINTS MAY RE SULT IN DAMAGE TO THE AMPLIFIER OR LOUDSPEAK ERS DAMAGES CAUSED IN SUCH A WAY ARE NOT COV ERED BY WARRANTY gt Before you start always make sure that your Bugera Valve Amplifier is connected to a suit able louds
5. illustrated 10 Specifications Limited warranty SPECIAL NOTE NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ONLY 1 Other warranty rights and national law 1 This limited warranty does not exclude or limit the buyer s statutory rights provided by national law in particular any such rights against the seller that arise from a legally effective purchase contract 2 The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law 2 Online registration Please do remember to register your new BUGERA equipment right after your purchase by visiting http www bugera amps com and kindly read the terms and conditions of our limited warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 Limited Warranty 1 BEHRINGER warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one 1 year from the original date of purchase 2 BEHRINGER warrants valves tubes and meters contained in the product to be free of defects in material and workmanship if used under normal operat ing conditions for a period of 90 days from the original date of purchase 3 This limited warranty is subject to the conditions exclusions and l
6. the product must be returned in its original shipping carton together with the return authorization number The return shipment address will be indicated by BEHRINGER 3 Shipments without freight prepaid will not be accepted 5 Warranty regulations 1 Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealer s invoice 2 Ifthe product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship This limited warranty does not cover any such modification adaptation irrespective of whether it was carried out properly or not Under the terms of this limited warranty BEHRINGER shall not be held responsible for any cost resulting from such a modification adaptation 3 Free inspections and maintenance repair work are expressly excluded from this limited warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons tubes guitar strings illuminants and similar parts 4 Damage defects caused by the following conditions are not covered by this limited warranty gt improper handling neglec
7. AIN id hdi e BRIGHT 8 9 Ts 10 Front panel of the BUGERA 6260 Front panel 13 1 The POWER switch is used to turn the power of the BUGERA amplifier on and off 2 STANDBY switch allows you to place the amp in STANDBY mode This way the amp is idle but the operational temperature of the valves is maintained POWER switch turned on AN 3 The REVERB control determines the amount of the gt built in reverb effect The 6262 and 6262 212 features individual REVERB controls for the LEAD and CLEAN channels The supplied footswitch lets you activate the REVERB effect see Chapter Foot switch 4 The PRESENCE control modifies the amp s damping factor at high frequencies This is used to fine tune the high frequency range of the speaker cabinet The 6262 or 6262 212 features individual PRES ENCE controls for the LEAD and CLEAN channels 5 This is the VOLUME control that lets you adjust the volume level of the LEAD channel 6 Thisis the VOLUME control that lets you adjust the gt volume level of the CLEAN channel ATTENTION TO AVOID DAMAGE TO YOUR AMP NEVER USE THE BUGERA VALVE AM PLIFIER WITHOUT A LOUDSPEAKER CON NECTED 14 15 16 17 7 The passive TREBLE control adjusts the upper fre quency range The 6262 and 6262 212 features separate TREBLE controls for the LEAD and CLEAN channels 8 passive MID control adjusts the middle fre quency range The 6262 and 6262 212
8. appropriate voltage rat ings for your country included At all times make the connections to the amplifier before plugging the cable into a power outlet 26 This isthe SERIAL NUMBER of the amplifier Footswitch REVERB FX LOOP Footswitch BUGERA FSB104A 27 The 7 pin DIN connector is provided to connect the footswitch cable included Then the cable is connected to the FOOTSW itch connector of the BUGERA amplifier Be sure to make a connection before switching on the amplifier 28 The CLEAN switch activates the CLEAN CRUNCH channel 29 The LEAD switch activates the LEAD channel Its LED illuminates when the channel is active 30 The REVERB switch activates the REVERB effect Its LED illuminates when the effect is active 31 The FX LOOP switch activates the FX LOOP func tion Its LED illuminates when the FX LOOP is ac tive 6 Control elements 12AX7B 6L6 EL34 12AX7B 6L6 EL34 6L6 EL34 6L6 EL34 Inside the BUGERA 6260 Inside the BUGERA A DANGER High voltage Risk of death High voltages of up to 500 V DC may be present inside the casing for long periods after being disconnected from the mains To avoid lethal electric shock do not open the casing There are no user serviceable components inside Refer all maintenance to qualified service personnel Remove the mains cable when the unit is not in use The parts inside the amplifier operate at high vo
9. edance of the used speaker cabinet When connecting two cabinets with the same impedance the switch should be set to half the value of one of the cabinets For example two 16 Ohm cabinets would require an 8 Ohm setting while two 8 Ohm cabinets need to be set to the minimum impedance of 4 Ohms Please also read Wiring the BUGERA AN 23 Both the paralleled LOUDSPEAKER outputs 14 mono jacks are used to connect the speaker cabinet s The minimum impedance is 4 Ohms The IMPEDANCE switch should always be set to match the impedance of the used speaker cabinet A ATTENTION TO AVOID DAMAGE TO YOUR AMP NEVER USE THE BUGERA VALVE AM PLIFIER WITHOUT A LOUDSPEAKER CON NECTED Rear panel of the BUGERA 6260 SERIAL NUMBER LOUDSPEAKER RISK OF ELECTRIC OS Cn A Hot surface Do not touch OO AMPLIFIER OUTPUT FOR cn 120 WATTS RMS 4 OHMS MIN SPEAKER IMPEDANCE FSB10g ONL JACKS PARALLELED N11999 AN 24 WARNING ONLY REPLACE THE FUSE WHEN THE MAINS CABLE HAS BEEN DISCONNECTED The FUSE is found in the fuse holder If the fuse is blown it needs to be replaced with a fuse of the same kind by all means Otherwise the unit could seriously be damaged in which case the warranty is void If the fuse is blown repeatedly you should take the unit to a qualified service technician A 25 The IEC MAINS connector is used to connect the mains cable that has the
10. hat you require ATTENTION TO AVOID DAMAGE TO YOUR AMP NEVER USE THE BUGERA VALVE AM PLIFIER WITHOUT A LOUDSPEAKER CON NECTED Before you get started Your product was carefully packed at the factory to en sure safe transport Nevertheless if the box is damaged inspect the unit immediately for signs of damage gt If the unit is damaged please do NOT return it to us but notify your dealer and the shipping company immediately otherwise claims for damage or replacement may not be granted gt Always use the original box to prevent dam age during storage or transport gt Make sure that children cannot play unsuper vised with the unit or its packaging gt Please ensure proper disposal of all packing materials Ensure adequate air supply and to avoid overheating do not place the unit near radiators etc gt Please make sure that all devices are properly grounded For your own safety never remove or disable the ground conductors from the de vices or on the power cords The unit must al ways be connected to the mains outlet with a protective grounding connection gt tone quality may diminish within the range of powerful radio broadcasting stations and high frequency sources Increase the dis tance between the transmitter and the unit and use shielded cables for all connections Online registration Please do remember to register your new BUGERA equip ment right after your purchase by visiting ww
11. igh output level that could distort the HIGH GAIN input only 6260 and 6260 212 The HIGH GAIN input 6262 and 6262 212 IN PUT is 6 dB louder than the LOW GAIN input and is used for most electric guitars The HIGH GAIN and LOW GAIN connectors have identical sensitivity when used at the same time both with LOW GAIN sensitivity Control elements 5 FX LOOP me OUT SEND RETURN E og Rear panel AN CAUTION Hot Risk of injury During use the valves get very hot and high surface temperatures may be reached at the rear of this unit Avoid touching the controls and connectors on the rear panel during use To avoid acci dental contact with hot surfaces place the rear panel so that it faces a wall 18 The SEND output is used to connect a shielded 1 4 mono jack cable to the input of an external effects unit 19 The RETURN input is used to connect a shielded 14 mono jack cable to the output of an external effects unit 20 The PREAMP OUT SEND output takes the preamp signal of the amp in order to feed the signal to a second amplifier and loudspeaker combination for example 21 The 7 pin FOOTSW itch connector is provided to connect to the supplied BUGERA FSB104A foot switch Please be sure to connect the cables before switching on the amplifier Refer to Footswitch for details 22 The IMPEDANCE switch lets you specify the loud speaker impedance Always apply the value that is identical to the imp
12. imitations hereinafter set forth If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under 5 BEHRINGER will at its discretion either replace the product by providing a new or reconditioned product or repair the product using suitable new or reconditioned parts In the case that other parts are used which constitute an improvement BEHRINGER may at its discretion charge the customer for the additional cost of these parts In case BEHRINGER decides to replace the entire product this warranty shall apply to the replacement product for the remaining initial warranty period i e one year from the date of purchase of the initial product 5 If the warranty claim proves to be justified the product will be returned to the user freight prepaid 6 Warranty claims other than those indicated above are expressly excluded PLEASE RETAIN YOUR SALES RECEIPT AS IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE 4 Return authorization number 1 To obtain warranty service the buyer or his authorized dealer must call BEHRINGER as exclusive distributor of BUGERA products see enclosed list during normal business hours BEFORE returning the product All inquiries must be accompanied by a description of the problem The buyer or his au thorized dealer will receive a return authorization number 2 Subsequently
13. ity This limited warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product 7 Claim for damages Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim consequential damages In no event shall the liability of BEHRINGER exceed the invoiced value of the product 8 U S Customers only THE FOREGOING CONSTITUTES THE ONLY WARRANTY MADE BY BEHRINGER WITH RESPECT TO THE PRODUCT AND IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED Any implied warranties including without limitation any implied warranties of merchantability or fitness for any particular purpose imposed under state law are limited to the duration of this limited warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not be applicable to you BEHRINGER ASSUMES NO LIABILITY FOR PROPERTY DAMAGE RESULTING FROM FAILURE OF THIS PRODUCT NOR ANY LOSS OF INCOME SATISFACTION OR DAMAGES ARISING FROM THE LOSS OF USE OF SAME DUE TO DEFECTS OR AVAILABILITY OF SAME DURING SERVICE Customers in the European Union please contact BEHRINGER Germany Support for further details Technical specifications and appearance are subject to change without notice The information contained herein is correct at the time of printing All trade marks except BUGERA the BUGERA logo and THE
14. ltages and high temperatures To avoid damage and injury that results from fire or electric shock do not drop or spill anything into the unit s casing Control elements INSTRUCTIONS FOR QUALIFIED SERVICE PERSONNEL ONLY Remove the backside of the amplifier s casing to get to the valves and the control elements 32 33 34 A 35 36 gt AN These are the sockets for the 12AX7A B C pre amp valves These are the sockets for the 6L6 and EL34 power amp valves Please take care that the BIAS SE LECT switch 34 is set correctly The BUGERA amp is supplied with 6L6GC power amp valves when it leaves the factory The BIAS SELECT switch allows the amplifier to optimally adapt to the used valves 6L6 or EL34 The BIAS TEST connector lets you connect a volt meter in order to measure the power amp valves bias adjustment Make sure that the voltmeter is set to direct current DC The BIAS ADJUST control is used to make the bi as adjustment Replacing the power amp valves also requires bias adjustment You should always use sets of four matched valves The valves of the BUGERA Series are ideal for this purpose CAUTION WE HIGHLY RECOMMEND THAT BIAS ADJUSTMENTS BE CARRIED OUT BY QUALIFIED PERSONNEL Wiring the BUGERA 1 CAUTION Hot Risk of injury During use the valves will get very hot and high surface temper atures may be reached at the rear of this unit To avoid burning yourself make all c
15. onnections while the unit is still cold AMP NEVER USE THE BUGERA VALVE AM PLIFIER WITHOUT A LOUDSPEAKER CON NECTED 1 ATTENTION TO AVOID DAMAGE TO YOUR The BUGERA amplifier has two paralleled LOUDSPEAKER outputs which are used to connect one or two speaker cabinets If you only connect one speaker cabinet be sure that the IMPEDANCE switch is set to match the impedance of the connected cabinet If you want to connect two speaker cabinets both cabi nets should have to the same impedance Be sure to have set the IMPEDANCE switch correctly In this case set it to half the value of one of the cabinets When us ing two 16 Ohm cabinets the switch therefore needs to be set to 8 Ohms and with two 8 Ohm cabinets set it to the minimum impedance of 4 Ohms CAUTION The loudspeakers in the combos are connect ed in series This results in an impedance of 16 Ohms IMPEDANCE switch Speaker cabinets 160 Impedances BUGERA 6262 Loudspeaker output Speaker cabinet BUGERA 412H BK BUGERA head with a speaker cabinet 8 Wiring the BUGERA The following figure shows a setup of the 6262 212 to gether with an external effects unit connected over the FX LOOP And the PREAMP OUT is connected to the line input of a mixer in order to send the signal to a recording device In addition the speaker signal of the BUGERA is picked up by a microphone and is fed to the microphone input of the mixer This way you get a
16. peaker Observe the correct imped ance for your loudspeaker and use the appro priate output socket gt Always use loudspeaker cables for connection between the amplifier and the loudspeaker Never use other types of cable like instru ment cable or microphone cable Switching the amplifier on and off gt Before connecting the amplifier to a power out let make sure that both POWER and STANDBY switches are set to the OFF position Power on mandatory gt Switch the POWER switch on wait for 60 sec onds then switch the STANDBY switch on Power off recommended Switch the STANDBY switch off wait for 30 seconds then switch the POWER switch off Note after powering off we recommend that the ampli fier is allowed to cool down for ten minutes before any attempt is made to move the amplifier This reduces the risk of mechanical damage to the sensitive valve ele ments AN Introduction Congratulations By purchasing the BUGERA you have chosen a state of the art valve amplifier This 120 Watt full valve amp offers you 2 full fledged channels with 3 tone controls a separate switchable Ef fects Loop plus integrated Reverb a Crunch function on the Clean channel and much more This way you re in full control and can get down to the nitty gritty your music Discover the killer sound of the BUGERA and be inspired by its versatility Whatever style you play this monster amp gives you the full valve power t
17. put level POWER AMPLIFIER SECTION Valves Type Output power Peak power Loudspeaker connectors Type Load impedance 44 kQ 6 dB 47 kQ or higher 10 dBV 470 kQ 10 dBV 47 kQ or higher 10 dBV 4 x 6L6GC 120W 16 8 42 14 mono jack connectors unbalanced 40 82 16 Q switchable Internal loudspeakers only 6262 212 and 6260 212 Type Impedance Power Total impedance POWER SUPPLY Power consumption Fuse Mains connection DIMENSIONS WEIGHT 6260 Dimensions H x W x D Weight 6260 212 Dimensions H x W x D Weight 6262 Dimensions H x W x D Weight 6262 212 Dimensions H x W x D Weight 2 x 12 BUGERA 12G70J8 8 Q 70 W IEC 16 Q series connection Max 350 W T 3 15 AH 250 V 100 120 V 50 60 Hz T 1 6 AH 250 V 220 240 V 50 60 Hz Standard IEC receptacle Approx 9 25 32 x 27 x 9 11 16 249 mm x 687 3 mm x 246 mm Approx 47 Ibs 21 5 kg Approx 20 13 32 x 27 x 9 3 4 518 46 mm x 687 3 mm x 247 65 mm Approx 63 Ibs 28 5 kg Approx 9 25 32 x 27 x 9 11 16 249 mm x 687 3 mm x 246 mm Approx 47 165 21 5 kg Approx Approx 20 13 32 x 27 x 9 3 4 518 46 mm x 687 3 mm x 247 65 mm 63 Ibs 28 5 kg We are constantly striving to maintain the highest professional standards As a result of these efforts modifications may be made from time to time to existing products without prior notice Specifications and appearance may differ from those listed or
18. second guitar sig nal which then can be amplified by a PA system and or can be recorded as well PA loudspeaker Power amplifier Main Out Multitrack recorder o0 ffe prm 255080 ee 00 06 34 12 LIL1 e M conoscono 222000 9 000 ag 000099 9 000 W 000000 9 000 w 20222025 2 000 w 22252022 2 OOD 2220200 9 000 a 800005 D a 9 a DEE w Effects processor ee 00 Mixing console Preamp Out Microphone Electric guitar Live setup with a BUGERA combo Audio connections The inputs and outputs of the BUGERA amplifier use mono jack connectors 4 amp Strain relief clamp Sleeve ground shield Tip signal Unbalanced 1 4 TS connector 74 mono jack connector Audio connections 9 Specifications PREAMP SECTION Valves Type Preamp high gain input Impedance Clean channel Nominal input level Min input level Max input level Lead channel Nominal input level Min input level 1 x 12AX7A 1x 12AX7B 3 x 12AX7C 6260 and 6260 212 4 x 12AX7C 6262 and 6262 212 470 kQ 34 dBV 50 dBV 0 dBV 80 dBV 92 dBV Preamp low gain input only 6260 and 6260 212 Impedance All levels attenuated by Effects send Impedance Nominal output level Effects return Impedance Min input sensitivity Preamp output Impedance Nominal out
19. t install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience recep tacles and the point where they exit from the apparatus 11 The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection 12 Where the MAINS plug or an appliance coupler is used as the disconnect device the disconnect de vice shall remain readily operable 13 Only use attachments accessories specified by the manufacturer 14 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over LALI 15 Unplug this apparatus during lightning storms or when unused for long periods of time 16 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is
20. t or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals gt connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable the country where the product is used gt damage defects caused by force majeure or any other condition that is beyond the control of BEHRINGER 5 Any repair or service performed by any person or entity other than a BEHRINGER authorized service center is not covered by this limited warranty Any repair or opening of the unit carried out by unauthorized personnel user included will void this limited warranty 7 Any exchange of the tubes valves and associated biasing by any person or entity other than a BEHRINGER authorized service centre will void this limited warranty 8 Ifan inspection of the product by BEHRINGER shows that the defect in question is not covered by this limited warranty the inspection costs are payable by the customer 9 Products which do not meet the terms of this limited warranty will be repaired exclusively at the buyer s expense BEHRINGER will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit Costs for freight and packing will be invoiced separately C O D When the buyer has sent in a written repair order such costs will also be invoiced separately 6 Warranty transferabil
21. w bugera amps com and kindly read the terms and conditions of our warranty carefully Should your BUGERA product malfunction our goal is to have it repaired as quickly as possible To arrange for warranty service please contact the retailer from whom the equipment was purchased Should your BUGERA dealer not be located in your vicinity you may directly contact the BEHRINGER company nearest to you This contact information is included in the original equip ment packaging Global Contact Information European Contact Information Should your country not be list ed please contact our exclusive distributor BEHRINGER Singapore BEHRINGER Holdings Pte Ltd 1 Kim Seng Promenade 08 08 Great World City West Tower Sin gapore 237994 Tel 65 6845 1800 Fax 65 6214 0275 Registering your purchase and equipment with us helps us process your repair claims quicker and more efficient ly Thank you for your cooperation CAUTION gt Please note that high volume levels may cause permanent damage to your hearing and or your loudspeakers Turn all LEVEL controls to the left before switching on the unit Be sure to keep the volume at an appropriate level 4 Introduction Control elements MASTER LEAD CLEAN EQUALIZER LEAD CLEAN INPUT 96260 Q 120 WATT 2 CHANNEL POWER STANDBY VALVE AMPLIFIER bd 4 6 4 3 7 3 2 8 2 1 9 1 E Ges D 10 REVERB PRESENCE VOLUME i 1 GAIN G
Download Pdf Manuals
Related Search