OWNER`S MANUAL
Contents
1. NEVER permanently install in a recessed area of the wall This may result in blocked air flow overheating or fire ALWAYS mount to wall bracket before use DO NOT set on the floor or other surface to use NEVER use a wall mount bracket from another manufacturer rN WARNING For residential use only NOT for commercial use Any commercial or public use of this heater voids all warranties and could cause injury This product is not intended to be a primary heat source It is for supplemental heat only INDOOR use only NEVER use this heater outdoors Doing so may result in electric shock Risk of electric shock DO NOT OPEN No user serviceable parts inside NEVER modify this heater Doing so could result in personal injury or property damage Modification of this fireplace completely voids all warranties ALWAYS turn this heater off before unplugging it from the outlet ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning or before relocating the electric fireplace NEVER leave this heater unattended ALWAYS unplug this heater when not in use ALWAYS store this heater in a dry location NEVER use the fireplace if it has become wet Place the heater near a wall outlet so an extension cord is not needed If an extension cord is needed the gauge of the cord must be at least 14AWG and the rating must be at least 1875 Watts NEVER use a smaller gauge cord with a lower rating Doing so m2. blows warm air 2 Press again Indicator lights up 1500W heater turns on and blows hot air 3 Press again Heaters turn off The fan blows cool air for 10 seconds to allow heater to cool down then turns off Remote Control Control panel POWER switch must be ON to use remote control BUTTON ACTION and INDICATION CONTROL PANEL 1 Press once Beep Flame effect and indicator turn on 2 Press again Beep Power and all functions turn off 1 Press once Small indicator amp lights up Fan blows cool air 750W heater turns on and blows warm air 2 Press again Large indicator ee lights up 1500W heater turns on and blows hot air 3 Press again Heaters turn off Fan blows cool air to allow heater to cool down then turns off 1 Press once Flame effect gets brighter Press again until desired setting is reached 2 Press Flame effect gets dimmer Press again until desired setting is reached 1 Press once 2h light turns on Timer is set to 1 2 hour 2 Press again 1h light turns on Timer is set to 1 hour 3 Press until desired setting is reached Timer setting increases by 1 2 hour up to 7 h Examples 3 hours 2h 1h 7 hours 4h 2h 1h h 4 Press again Timer setting increases by 1 2 hour until desired setting is reached or until timer turns off 5 Press again to restart timer from Veh Temperature Limiting Control This heater is equipped with a Temperature Limiting Control Shou
3. Arrange power cord away from traffic area and where it will not be tripped over Connect to properly grounded outlets ONLY DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause electric shock or fire or damage the heater To prevent a possible fire DO NOT block air intakes or exhaust in any manner Doing so could cause a fire DO NOT use on soft surfaces like a bed where openings may become blocked A heater has hot and arcing or sparking parts inside DO NOT use it in areas where gasoline paint or flammable liquids are used or stored Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons ALWAYS plug heaters directly into a wall outlet receptacle NEVER use with an extension cord or relocatable power tap outlet power strip DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater NEVER use this heater in bathrooms laundry rooms or any other location where the heater could fall into a bathtub or pool become damp or come in contact with water AVOID FIRE Regularly inspect all air vents to make sure they are free from dust lint or other blockage Unplug the unit and clean with a vacuum ONLY DO NOT rinse or get wet NEVER hang this unit on a wall directly below an electrical outlet
4. ELECTRIC FLAT PANEL FIREPLACE HEATER Model Numbers WS G 01 WS G 02 OWNER S MANUAL Read and understand this entire owner s manual including all safety A WARNING information before plugging in or using this product Failure to do so could result in fire electric shock or serious personal injury A CAUTION Keep this owner s manual for future reference If you sell or give this product away make sure this manual accompanies this product toucnstone mart Furniture Beautiful IMPORTANT SAFETY INFORMATION A WARNING Read all instructions before using this heater This heater is hot when in use To avoid burns DO NOT let bare skin touch hot surfaces If provided use handles when moving this heater Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9m from the front of the heater and keep them away from the sides and rear Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions has been dropped or damaged in any manner Discard heater or return to authorized service facility for examination and or repair DO NOT run power cord under carpeting DO NOT cover power cord with throw rugs runners or similar coverings DO NOT route power cord under furniture or appliances
5. ay result in fire or electric shock ONLY use this heater on a 240V AC 15 Amp grounded circuit NEVER overload the circuit If this heater trips the circuit breaker unplug all other appliances on the same circuit before the next use Avoid plugging other appliances into the same circuit as this heater NEVER plug this heater into an outlet that is old cracked or has any loose wires or connections Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire ALWAYS check your heater cord and plug connections with each use i MAKE SURE the plug fits tight in the outlet Faulty wall outlet connections or loose plugs can cause the outlet to overheat li Heaters draw more current than small appliances Overheating may occur even if it has not occurred with the use of other appliances iii During use check frequently to see if the plug outlet or faceplate is HOT iv If the outlet or faceplate is HOT discontinue use immediately and have a qualified electrician inspect and or replace the faulty outlets The power cord supplied with the heater has three prongs two flat blades live and neutral and one round pin ground If a 3 slot receptacle is not available an adapter MUST be used The adapter MUST be properly grounded to the outlet box see figure at right NOTE Adapter NOT INCLUDED SAVE THESE INSTRUCTIONS Remove all parts and har
6. d this entire owners manual including all safety information before plugging in or using this product Failure to do so could result in electric shock fire serious injury or death Power Make sure the ON OFF switch located on the left side panel is in the OFF position Plug the power cord into a 110 120 Volt 15 Amp grounded outlet see IMPORTANT SAFETY INFORMATION on Pages 2 and 3 Make sure the outlet is in good condition and that the plug is not loose NEVER exceed the maximum amperage for the circuit DO NOT plug other appliances into the same circuit Methods of Operation This electric fireplace can be operated by the CONTROL PANEL located on the right side panel of the fireplace see figure below or by the battery powered REMOTE CONTROL The operation and functions of the two methods are the same Before operating please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3 and heed all warnings NOTICE When the heater is first turned on a slight odor may be present This is normal and should not occur again unless the heater is not used for a long period of time Front View Top View Hot air vent Rear View Left Side View Control Panel Operation BUTTON FUNCTION ACTION amp INDICATION ON Enables touch panel functions and remote control Turns on flame effect OFF Disables touch panel functions and remote control Turns off flame effect TIMER button Controls timer settings to turn off
7. dware from the carton and place them on a clean soft dry surface Parts and assembly steps are grouped for free standing or wall hanging use Check the parts list to make sure nothing is missing Dispose of packaging materials properly Please recycle whenever possible You will need the following tools not included Phillips screwdriver stud finder level tape measure electric drill 1 4 wood drill bit hammer Parts and Hardware B Wood Screws amp Washers 5 sets Step 1 Find a safe location Minimum clearance on each side 19 7 50 cm Minimum clearance below 9 8 50 cm Minimum clearance above 39 4 100 cm Minimum clearance from the front and sides 3 feet 90 cm Choose a location near an outlet so an extension cord is not required DO NOT position the unit directly Minimum 9 8 below a power outlet 29 em See Safety Information on pages 2 and 3 for warnings about safe placement safe installation and proper use of this product The wall mount fasteners included with this fireplace are for use ONLY with a hogg 6 S wood framed wall covered in drywall sheet rock For concrete walls cinder blocks or other wall types consult a professional for the best attachment methods ALWAYS unplug this fireplace heater before assembly or cleaning or before relocating Failure to do so could result in electric shock fire or personal injury STEP 2 A Loca
8. fireplace at selected time settings range from 0 5 hours to 7 5 hours FLAME button Makes flame effect dimmer NOTE Flame effect stays on until power button is turned off Flame effect must be on for heater to turn on FLAME button Makes flame effect brighter NOTE Flame effect stays on until power button is turned off Flame effect must be on for heater to turn on HEATER button Turns heater on and off NOTE The heater only works when the flame effect is on If the flame effect is off Q the heater will not turn on HEATER NOTE To prevent overheating the heater fan will blow cool air for 8 10 seconds before the heater turns on and after the heater turns off NOTICE 1 Press once Indicator light turns on Power turns on All functions enabled 2 Press again Flame effect turns off Unit goes to standby All functions turn off Press once Indicator light turns on Timer is set to 0 5 hours Press again until desired setting is reached Indicator lights show setting 1 Press once Flame effect gets dimmer 2 Press again until desired setting is reached Flame effect continues to get dimmer each time button is pressed 1 Press once Flame effect gets brighter 2 Press again until desired setting is reached Flame effect continues to get brighter each time button is pressed 1 Press once Indicator lights up Fan blows cool air for 10 seconds 750W heater turns on and
9. ld the heater reach an unsafe temperature 212 F 100 C the heater will automatically turn OFF To reset 1 Unplug the power cord from the outlet 2 Turn the ON OFF switch on the CONTROL PANEL to OFF Wait 5 minutes 3 Inspect the fireplace to make sure no vents are blocked or clogged with dust or lint If they are use a vacuum to clean the vent areas 4 With the POWER switch in the OFF position plug the power cord back into the outlet 5 Ifthe problem continues have your outlet and wiring inspected by a professional Remote Control Battery Information e This remote control uses two AAA battery Not included e Instructions for battery installation are on the Remote Control battery compartment NEVER dispose of batteries in fire Failure to observe this precaution may result in an explosion Dispose of batteries at your local hazardous material processing center Care and Maintenance Cleaning ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning performing maintenance or moving this fireplace Failure to do so could result in electric shock fire or personal injury NEVER immerse in water or spray with water Doing so could result in electric shock fire or personal injury Metal e Buff using a soft cloth slightly dampened with a citrus oil based product e DONOT use brass polish or household cleaners as these products will damage the metal trim Glass e Use a good quali
10. sing a 1 4 wood drill bit A If screws will go into three studs no drywall anchors are needed B Tap the drywall anchor s C carefully into the drywall holes until they are flush with the drywall surface Use care to avoid damage then directly into the wall studs J with the pilot holes and drywall anchors Thread et n the wall bracket E ALWAYS unplug this fireplace heater before assembly or cleaning or before relocating Failure to do so could result in electric shock fire or personal injury STEP 5 A With the help of a capable adult lift the fireplace A and align the hooks on the back of the fireplace with the slots on the wall bracket Carefully set the hooks into the slots an ab 2 _ O ab pa O o os gt ab pa O V V ab 2 O V S C C D H gt KO LP _ ab xX O pa O ab _ V ab xX 4 v ba O Ka O C ir gt gt a O pa O NS O c lt Thread the screws through the fireplace and into the wall bracket side tabs Tighten both screws B Secure the fireplace to the wall bracket with two M4x8 metal screws D one on each side with a Phillips screwdriver The unit may now be plugged in xX O a O O z Ka S v O Kan O C V p aa CZ v z Ka O gt O _ Ka o v ab pa O V O O O z Read and understan
11. te the wall studs using an electronic stud finder Mark the hole locations with a pencil The holes should be 8 20 3 cm apart and level The minimum height from the surface below must be 75 2 191 cm B Three screws should be screwed directly into wall studs Then no drywall anchors are needed C If only two studs are available two screws MUST be screwed directly into studs and the other screws must be screwed into the drywall anchors AVOID INJURY and DAMAGE Three screws should be screwed directly into wall studs If only two studs are available two screws must be screwed directly into the wall studs and additional screws must also be screwed into the drywall anchors anchors unting into three wall studs Mounting into two wall studs and drywal oe I i I I I I i P 1 ao I I I I I P ernn banann amp if i fa 3 he Ti ci T F r i L l i i l i L h fa i i i L i i 1 i Siea w ak i 9 o 1 i 1 1 J 1 i 1 1 J l 1 ee ee ee e Bome om o a O i A a a n s r SSS SS Se a a a SS ee F E a a E E e E E EE E E a EE E E Ee a a ae ee ee eee ee ee ee eee se See Se Se esses F 1 i i i i I I i I I i l i I I i i i i i i i i i 1 i J J i l i n rl I i i f l 1 l i l i i L l I i I i a 4 l 4 STEP 3 Drill a pilot hole into each mark u
12. ty glass cleaner sprayed onto the cloth or towel Dry thoroughly with a paper towel or lint free cloth e NEVER use abrasive cleansers liquid sprays or any cleaner that could scratch the surface Vents e Use a vacuum or duster to remove dust and dirt from the heater and vent areas Plastic e Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water e NEVER use abrasive cleansers liquid sprays or any cleaner that could scratch the surface Maintenance Risk of electric shock DO NOT OPEN any panels other than the bulb replacement plate No user serviceable parts inside ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning performing maintenance or moving this fireplace Failure to do so could result in electric shock fire or personal injury Electrical and Moving Parts e The fan motors are lubricated at the factory and will not require lubrication e Electrical components are integrated in the fireplace and are not serviceable by the consumer Storage e Store heater in a clean dry place when not in use 10
Download Pdf Manuals
Related Search