User Manual For WT-009M - Witura Technology Sdn Bhd
Contents
1. WT 009M IP65 Master GSM Controller User Manual amp Setting Instruction UNTURA WII TURA CORPORATION SDN BHD WT 009M Wiring Diagram Description WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRI GHT 2010 WITURA CORPORATION SDN BHD PACKAGE CONTENTS 1 1 pc IP65 Enclosure 2 1 pc WT 009M Main Board with GSM Module mounted 3 1 pc Power Adapter 4 1 pc Battery Backup 5 1 pc GSM Antenna INTRODUCTION The WT 009M is the Master GSM Controller that communicates with all of the slave units in the System The Master Controller will identify all the incoming telephone calls and security check they are authorized and forward the instructions to the appropriate Slave The Master unit can store up to 20 separate land Line or mobile phone numbers which can be added and removed remotely The system also has the facility to monitor the consumption used based on the consumption time related to real cost which can be remotely accessed at anytime as sub total daily weekly spend and running total spend and the value spend can be updated at any time The Master unit can be positioned in any location and is a complete stand alone system only requiring a 12 volt permanent supply and backed up with a 12 hour On board battery The Master will communicate with all the slave units regardless of any location or distance apart anywhere in the world The system also once ins2. allow the Master to call certain numbers in the Responder list when the user calls the Master To allow the Master to call the first 10 position in the Responder List only the syntax of the command is the following PWD123456 RERN 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 Where 1 is a number enabled for the first 10 position in the Responder list and 0 is a number disabled for the last 10 position in the Responder list To allow the Master to call position 2 4 6 8 10 12 14 16 18 20 in the Responder List the syntax of the command is the following PWD123456 RERN 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Where 1 is a number enabled for position 2 4 6 8 10 12 14 16 18 20 in the Responder list and O is a number disabled for position 1 3 5 7 9 11 13 15 17 19 in the Responder list To allow the Master to call all position in the Responder List the syntax of the command is the following PWD123456 RERN 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Where 1 is a number enabled for all position in the Responder list WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD CSQ Check GSM signal quality This command is useful to see what is the GSM network signal level the Master Device is receiving If you send the command PWD123456 CSQ You should receive an SMS with signal quality in range O to 31 if it is O we doubt it will ever answer Y
3. M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD You should install the WT 009M Master Device in a place where there is GSM signal coming from the operator you want to use Check it with a phone before proceeding with the installation If you need to install the device in a place with little signal you may consider using an external antenna that we may supply as an option to be purchased separately with 5m cable You should then insert the SIM of the operator you want to use and program in the White List the numbers enabled to open the gate using the command WHL Note You must remove the PIN request from the SIM before inserting it in the unit otherwise the device will not work In order to do so insert the SIM in a phone and disable the PIN request usually there is a security menu that enables you to do so If you don t do it and switch on the unit more than 3 times you will have to reset the PIN using the PUK WT 009M IP65 PROGRAMMING INSTRUCTIONS via SMS Only You can program the WT 009M with SMS commands using your phone It is safe to do so because in addition to the fact that other people may not know the number of the SIM inserted in it we also use a Password that makes it impossible for anybody who doesn t know it to access the system by chance Remember that commands must be CAPITAL LETTERS It is PWD not pwd CAP not Cap etc Don t add spac
4. es or any other character Attention Please program the WT 009M unit systematically begin with programming the white list first Once you issue a command with an SMS you will receive a confirmation SMS PWD Password This command must always come first Use 6 digits as a password The standard default one when the device comes from the factory is 123456 We suggest that you change it using the CAP command In all the following examples we will use 123456 as an example of password WHL White List This is the command that you will use most It is used to add or remove numbers that are enabled to call into the Master unit You can add up to 99 numbers in WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD the list Every position must be indicated in the command and we advise you to keep a list written somewhere to know which numbers are in and in which position e To add a number the syntax of the command is the following PWD123456 WHLO1 3593334444 Where 01 is the position in the list and 3593334444 is the number enabled Please note that it is possible to program up to a maximum of 10 digits for a number If it has more digits you should use the rightmost ones For example if your number is 33446665555 you should program 3446665555 If your number appears as 393489999888 you should not program the country code 39 If your number has only 9 digits or
5. less it is not a problem The important thing is that you don t exceed 10 digits e To check which is the number in a place of the list PWD123456 WHLO1 Example of Returned Message WHLOL 3446665555 e To erase a number PWD123456 WHLOLD Returned Message WHLO1 OK e To erase all number PWD123456 WHL99D Returned Message DELALL OK Note To erase the number stored in place 99 in the list only you would send the command PWD123456 WHL99 0000000000 CAP Change Password Use this command to change the password with a new one that you will chose for your device don t forget it or you will have to send the unit back to us to reset it and this has a cost The CAP command must be issued 2 times to be sure you don t digit a wrong one Of course it must be preceded by the old password WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD For example to change the password 123456 into the new password 333444 you need to send the following SMS PWD123456 CAP333444 CAP333444 Example of Returned Message CAP 333444 ACM Access Mode This command allows you to open only to people that are in the white list or to anybody calling the SIM number PWD123456 ACMO it is a zero Warning With the above command you allow free access to anybody calling Returned Message ACM OFF PWD123456 ACM2 With the above command you allow only pe
6. ople that are in the white list This is the standard and recommended option Returned Message ACM ON TLP Responders List This is the command that allows you to add or remove the Responders numbers that the Master unit programmed to call You can add up to 20 numbers in the list Every position must be indicated in the command and we advise you to keep a list written somewhere to know which numbers are in and in which position To add a number the syntax of the command is the following PWD1234564TLP1 35555554444 Where 1 is the position in the list and 35555554444 is the number enabled Please note that it is possible to program up to a maximum of 10 digits for a number If it has more digits you should use the rightmost ones For example if your number IS 33446665555 you should program 3446665555 If your number appears as 393489999888 you should not program the country code 39 If your number has only 9 digits or less it is not a problem The important thing is that you don t exceed 10 digits WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD To check all the number in the list PWD123456 TLP Example of Returned Message TPL1 3446665555 TPL2 3446665556 TPL3 3446665557 TPL4 3446665558 TPL5 3446665559 TPL6 3446665560 Note This command will return all value in the Responder List with 3 SMS RERN This is the command that will
7. ou should have a signal above 12 to be sure of being able to open the gate in any condition Better if above 16 You should add an external antenna if this is not the case or eventually even change operator with another that serves your area better Example of Returned Message CSQ lt 21 gt TECO Call meter counter This command is useful to count the total pre set value of usage per call the user made to the Master Device e To program the value of each call made to 0 15censt the syntax of the command is the following PWD123456 TECO 00015 Every call made will increment the counter multiply the programmed value For example if 10 calls are made to the Master the total value would be 10 x 00015 equal to 00150 1 50 e To enquire the total counted value the syntax of the command is the following PWD123456 TEIN Note You should receive an SMS with total counted value of both Call meter and Input counter Example of Returned Message TECO 00150 INCO 00000 e To reset the total increment counter value the syntax of the command is the following PWD123456 TECL WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD INCO Input counter This command is useful to count the total pre set value of usage per pulse to the input e To program the value of each pulse to 0 10 cents the syntax of the command is the following PWD123456 INCO 00010 Every p
8. rkmanship for 1 year warranty Witura Corporation Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning damage mechanical shock water damage fire damage or damage arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 009M is a product of Witura Corporation Sdn Bhd and is manufactured by ShenZhen Witura Telecommunications Co Ltd WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD
9. talled and programmed incurs no call costs to any of the users and the only nominal cost is the changes to the parameters which would be infrequent 2 HOW IT WORKS The user numbers are stored into the memory of the Master unit and are the only telephone numbers the master will accept and authorize When the user calls that number the master will read it authorize it and reject the call WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD The master will then systematically call all the Responders the master has been programmed to call The Responders will receive a telephone call in the sequence order that the numbers have been stored into the system The Responders will read the incoming number and authorize that it is from the correct Master unit and hang up The Responders will then latch the output relays to perform whatever command was required and for what time the unit programmed to latch Master Calls each User calls the Master 3 INSTALLATION INSTRUCTION Note It is essential that you read the step by step instructions fully prior to installing and programming the unit To install the WT 009M Master Device you need to provide the power by means of 12 to 24 VDC The power supply must be able to stand 2 4A Don t use telephone battery chargers Most of them rely on the phone battery and are unable to supply the power needed WT 009
10. ulse will increment the counter multiply the programmed value For example if the input received 20 pulses the total value would be 20 x 00010 equal to 00200 2 00 e To enquire the total counted value the syntax of the command is the following PWD123456 TEIN Note You should receive an SMS with total counted value of both Call meter and Input counter Example of Returned Message TECO 00150 INCO 00000 e To reset the total increment counter value the syntax of the command is the following PWD123456 INCL Reset the WT 009M Unit To reset the unit you can send the following SMS command to the unit Text Command REST XXXXXX XXXXXX stands for 6 digits password based on PWD and it can be changed anytime with CAP command Example WT 009M USER MANUAL Rev 1 0 Technical Support Technical witura com COPYRIGHT 2010 WITURA CORPORATION SDN BHD e To reset the unit with default password 123456 the syntax of the command is the following REST 123456 Returned Message REST OK 6 TECHNICAL SPECIFICATIONS Item Description Model WT 009M Operating Voltage 12VDC No of Inputs 00000 1 Digital protected Inputs GSM Modem Quad Band 850 900 1800 1900mhz Humidity 00000 Less Than 80 RH Operating Temperature 0 C to 55 C Physical size Weight 1 2kgs WARRANTY Witura Corporation Sdn Bhd guarantees all WT 009M GSM Master Controller against defective parts and wo
Download Pdf Manuals
Related Search