User`s Manual
Contents
1. CORPORATION Ness 104 443 HD SDI camera User s Manual REV1 3 Nov11 CORPORATION www ness com au HEAD OFFICE Ness Security Products Pty Ltd ABN 28 069 984 372 Ph 61 2 8825 9222 Fax 61 2 9674 2520 ness ness com au SYDNEY Ph 02 8825 9222 Fax 02 9674 2520 sales ness com au MELBOURNE Ph 03 9875 6400 Fax 03 9875 6422 nessmelb ness com au BRISBANE Ph 07 3399 4910 Fax 07 3217 9711 nessbris ness com au PERTH Ph 08 9328 2511 Fax 08 9227 7073 nessper ness com au ADELAIDE Ph 08 8152 0000 Fax 08 8152 0100 adelaide ness com au COPYRIGHT NOTICE All rights reserved No part of this publication may be reproduced transmitted or stored in a retrieval system in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Ness Ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing product development and improvement 2011 Ness Corporation Pty Ltd ABN 28 069 984 372 Table of Contents ie TOV CROW airina eter poem pane usec ancumen seu ed aaiued scmaues net en eu oeudastacasdesaaweagucnd daceateh E 1 1 FOO eee ne ee oe ee ee ee ee ne Creer en ere nee eee 1 2 Package COMEM S assirian a E duno E E amend babs ancauaendseandcenes 1 3 DIMENSIONS ceee a aa a a a hein 2 damera AO izr n a S 2 1 PPOGUGEA DDIICATOM aers etuaracsutesresucussciocmied senoeserunrereets2. Step 4 Turn the zoom to the extreme telephoto position and then focus on the subject Step 5 Set the zoom to wide angle position Step 6 Loosen the back focus ring s retaining screw with the supplied adjuster and adjust the back focus ring for sharp picture Back Focus Adjuster Ne Back Focus Ring Step 7 Repeat steps 3 6 until focus can stay the same throughout the zoom range Step 8 Tighten the back focus ring s retaining screw to fix the ring 8
3. there will be no SDI A signal 2 4 Lens Mounting If use C Mount lens after removing the camera s plastic cover users need to mount the C CS mount adapter to the camera Then attach the lens onto the C CS mount adapter as the illustrations shown below Appendix A Technical Specifications Sensor dR Sony Prorennve CMOS Total Pixel 2144 H x 1588 V 3 4M C CS Mount Lens Fixed Vari focal iRFunction COO Mechanical Lens Mounting C CS Mount Video Output Remote Control Up to 2 sets RS 485 Connectors TACT Switch 5 pin OSD Control Alarm In Out Up to 2 sets Die i iii ii 125 x 82 x 52 mm L x W x H w o Lens DC 12V 10 AC 24V 10 Optional Appendix B Back Focus Adjustment When to adjust back focus Back Focus refers to the distance from the rear lens element to the camera focal plane In most cases it is required to adjust back focus only when the camera s lens cannot hold focus throughout its zoom range What requirements Tools required when carrying out back focus adjustment include 1 Back focus adjuster in the IP Camera s package 2 Test chart contrasting object How to adjust back focus Step 1 Set the camera on a stable mount with the test chart or object at least 75 feet 23 meters away or as far as possible Step 2 Make sure the iris is wide open Therefore it is advised to keep the environment in low light condition Step 3 Adjust the focus to infinite far co
4. ack focus adjuster CD Quick Guide bundled software and documentation Dimensions Unit mm 2 1 Camera Cabling Please follow the instructions below to complete SDI Box Camera cable connections Product Application Connect the SDI Box Camera to other devices as shown in the diagram to complete a video surveillance solution I 5D Box Camera SDI Box Camera pe E gn i DG800 HD SDI Digital Video Recorder Contral Keyboard SDI Box Camera SDI Box Camera sas alate RS 485 Mhata ied 2 2 Connectors The diagram below shows the IP Camera s reset button and various connectors Definition for each connector will be given as follows Single Board Dual Board LINE IN LINE LINEIN MIC IN i OUT MIC IN a L p i p i IE Oo Weni aO I 60 9 0 9 69 HHHHHE I VIDEO WO12345678 DC 12V AC 24W Definition Remark Dual Board DC12V AC24V AC 24v AC_IN2 DCI Deiv Ce voo enco i CH DIP Switch TV system Resolution Frame Rate Setup BNG a 2 ALARMINe Leis o aam our LITIR ALARM_OUT 2 3 TV System Resolution Frame Rate Setup Please refer to the illustrations below to set up the Camera TV system resolution and frame rate Setting Pi Defi in efinition OFF a Resolution 720P 1080P Ca Frame Rate 500 25 30 654321 a Reeva D s Reena se RENN ei Wsysen NTSC PAL Please kindly notice that while BNC output is on
5. ieane 2 2 CS ONIMEGCIONS sisira Toen TE ES 2 3 TV System Resolution Frame Rate Setup ccc ceccccecccececeeeceeeeseeeeeeeseeesseeeseeeeaeees 2 4 ESAS MOUNINO eici a a A Appendix A Technical Specifications cccccssseeescseseeeeccesseeeeesseeeseeeseeeseeenseeseosseeseoenseessonaes Appendix B Back Focus AdjUStMe nt cccecseceeeseeecenseeeeeneeseeseeseeneeeseaneeseenseseenseeeonneesoensessones 1 1 Overview HD CCTV standard offers a new opportunity for traditional CCTV surveillance industry It makes CCTV Camera transmit high definition image through coaxial cable Combing SDI standard with high quality SONY CMOS sensor the SDI Box Camera provides 1920x1080 resolution high quality image as well as easy and low cost installation With innovative WDR function and digital noise reduction technology the SDI Box Camera can offer close up images with exceptional details even at night time Features e Progressive Scan CMOS Sensor e Full HD 1080P 30fps 60fps e HD 720P 30fps 60fps e Wide Dynamic Range e Digital Noise Reduction e Intuitive OSD Operation e BNC output support e DC12V Support e AC24V Support e RS 485 Support e Alarm I O Support Optional 1 2 1 3 Package Contents Please check the box contains the items listed here If any item is missing or has defects DO NOT install or operate the product and contact your dealer for assistance hea SDI Box Camera B
Download Pdf Manuals
Related Search