operating instructions - produktinfo.conrad.com
Contents
1. and minus If connected incorrectly the external siren the external strobe as well as the siren control will be damaged When using a power supply that cable should also be fed through the opening and connected to the BU1 socket B in figure 1 on page 10 The inner contact is the outer contact is the power supply must provide a stable output voltage of 12V and a current of 1A The outer diameter of the hole for the cables must be sealed from inside and outside with silicone for example to prevent the penetration of moisture or draughts Afterwards mount the siren control on the upper 2 screws The cables should be inaccessible Secure the siren control by tightening the third screw to the wall Do not plug the power supply into a socket yet Do not insert the batteries yet The casing should remain open 13 8 Registering the siren control FAZ 3000 SI 2 with the base station a Preparing the alarm base station IS First the alarm base station must be prepared to receive the registration signals from sensors including the siren control Up to 4 siren controls can be registered and operated by the alarm base station FAZ 3000 2 Carry out the following steps on the FAZ 3000 2 alarm base station Description of procedure Display on LCD You must be on the top level The LCD should disarm appear as on the right for2. disarm 15 17 09 02 troubles ext siren ext siren trigger disarm 000_ int arm 0 000_ ext arm ALS t ext arm SLk ext arm 1101 21 If the cursor appears to the right see arrow under the figure to the right use the 4 and buttons to switch between the 3 different states disarmed internally armed and externally armed Pressing the OK button applies the new settings Exit the menu by pressing the C button twice This returns you to the normal display mode top level 22 ext arm 1101_ t ext siren trigger disarm 15 43 09 02 c Setting the alarm duration for the external siren The factory default setting for the alarm duration of the external siren connected to the siren control is 60 seconds you may adjust this time to any duration between 10 to 300 seconds Caution The maximum alarm duration for an acoustic alarm that is generated by a siren outside is restricted by law to 3 minutes an external strobe light can signal for longer This may vary at health resorts for example As a precaution check this out with your local council The alarm duration for indoor areas is not normally affected by this restriction However if an internal alarm signal is very loud and is also clearly audible outside then the legal restriction ma
3. Influence on the radiation pattern of antennas due to the distance from the transmitter or receiver to conductive surfaces or objects also to human bodies or the ground Broadband interference in urban areas that reduces the signal to noise ratio the signal is no longer recognised due to this noise Interference radiation resulting from insufficiently shielded electronic devices for example operating computers or similar 30 14 Technical specifications Connections eeceeeeeeeees 1 x BU1 socket for power supply not supplied 12V 1A inner contact 1 x KL1 terminal for sabotage contact 1 x KL2 terminal for 12V siren 1 x KL3 terminal for 12V strobe Maximum power for externally connected siren and strobe combined total 0 8A Batteries i k ah anet 4 x type C 4xAA Battery life 0 eee up to 3 years alkaline batteries FreQUeN Cy irens 868 35MHz Range up to 300m in free field Dimensions ccceeeeeeees 123mm x 240mm x 50 mm W x H x D PUSS gecccicsscedsdcgecsdigeaczetssz het S11 1A 250V slow blow S12 0 8A 250V slow blow The range depends on the version of the FAZ 3000 2 alarm base station that is used Earlier versions only permitted a range of up to 100m 31 15 Brief instructions a Registering the siren control with the alarm base station Install the siren control but do not insert the batteries or connect available power
4. This returns you to the normal display mode top level dur siren 60 sec dur siren 90 sec ext siren dur siren disarm 22 10 08 02 d Setting the alarm duration for the external strobe The factory default setting for the alarm duration of the external strobe connected to the siren control is 20 minutes you may adjust this time to any duration between 1 and 100 minutes To set the alarm duration for the external strobe light proceed as follows The alarm base station must be in the top level The disarm LCD should appear as on the right for example 21 57 08 02 with the time and the date z Briefly press the Men a A button on the control unit of the FAZ Z alarm base station troubles Use the 4 and Y buttons to select the ext ext siren siren external siren see the figure on the right Confirm your selection by briefly pressing the OK ext siren button trigger e Use the 4 and buttons to select the dur ext siren flash alarm duration for the strobe light menu Tir Fiach Confirm your selection by briefly pressing the OK dur flash button 20 MiA The current setting for the alarm duration appears on the LCD factory set to 20 minutes e Use the 4 and buttons to select the required dur flash alarm duration You can set this to a value be
5. During an attack an alarm is set off by the siren control setting 1 IS Please consult these 3 tables when changing the settings see item b on the next page 20 b Changing the alarm trigger settings The alarm base station must be in the top level The LCD should appear as on the right for example with the time and the date Briefly press the Meni a A button on the control unit of the FAZ Z alarm base station e Use the 4 and buttons to select the ext siren external siren i e the siren control itself Confirm your selection by briefly pressing the OK button The LCD displays trigger alarm trigger Confirm your selection by briefly pressing the OK button Please note the position of the cursor _ If the cursor is located precisely at this position at the far right you can use the 4 and buttons to switch between the three different states disarmed internally armed and externally armed Here the dash and number sequences correspond to the settings in the tables on pages 18 20 e Using the C and gt buttons you can select the required entry position cursor _ sits beneath the selected position You can change the value using the 4 and buttons T Siren control sets off 0 Siren control does not set off Positions that have a cannot be changed
6. Overvoltages on the power supply line can damage the device While for example a television or another device can easily be unplugged remove the power plug from the socket this is not possible with the siren control when choosing to operate with power supply However suitable accessories are available on the market which reduce the risk for the siren control for example overvoltage protectors or similar lightning protection devices Such devices however do not provide absolute protection against overvoltages or lightning Do not leave packaging material lying around This may become a dangerous plaything in the hands of children Handle the product with care knocks blows or even a fall from a low height can damage it b Batteries and rechargeable batteries Keep batteries rechargeable batteries out of the reach of children When inserting the batteries rechargeable batteries make sure that the polarity is correct Do not leave batteries rechargeable batteries lying around as they could be swallowed by children or pets In such case seek immediate medical care Leaking or damaged batteries rechargeable batteries may cause acid burns if they come into contact with skin Therefore please make sure you use suitable protective gloves Make sure that batteries rechargeable batteries are not short circuited or thrown into a fire They might explode Never take batteries rechargeable batteries apart Conventional batter
7. flash in a triangle is used to alert you to potential personal injury hazards such as electric shock The icon with an exclamation mark in a triangle points to important information in this user manual that must be observed The hand symbol indicates special tips and information on operation 7 5 Safety instructions The product s guarantee becomes invalid if the product is damaged as a result of the failure to observe these operating instructions We do not assume any liability for any result ing damages We do not assume liability for damage to property or personal injury caused by improper use or failure to observe the safety instructions In such cases the product s guaran tee becomes invalid Dear customer the following safety instructions are intended to protect you as well as the device Please take time to read through the following points a General information If you are not sure how to assemble connect and install the device or if you have doubts about its mode of operation contact a skilled technician For safety and licensing CE reasons any unauthorised alterations to and or modification of the product are not permitted The product is approved for installation and operation in dry closed indoor rooms only Make sure that the product does not get damp or wet This product is not a toy and should be kept out of the reach of children Thunderstorms can be a danger to all electrical equipment
8. supply yet Place the alarm base station in search mode Insert 4 AA batteries into the siren control Insert 4 type C batteries into the siren control Connect the siren control power supply to the line voltage The alarm base station should now recognise the siren control Enter a name for the siren control Return to the top level of the alarm base station press the C button three times b Opening the casing replacing the batteries Place the siren control in maintenance mode at the alarm base station Open the casing of the siren control Replacing the batteries Close the casing Exit the maintenance mode at the alarm base station 32 16 Declaration of conformity DOC We Conrad Electronic Klaus Conrad StraRe 1 92240 Hirschau Germany hereby declare that this product complies with the fundamental requirements and other relevant regulations of directive 1999 5 EC IS You can find the declaration of conformity for this product at www conrad com 33 34 35
9. al obligations and also make a contribution to environmental protection 29 13 Information on the range Ranges and interference The siren control operates in the 868MHz range which is also used by other radio services Therefore devices that operate on the same or neighbouring frequencies may restrict both its operation and its range The specified range of 300m is the free field range which means the range with visual contact between the transmitter and receiver In practice however ceilings walls garages or neighbouring buildings between the transmitter and the receiver may affect and reduce the range accordingly The range also depends on the version of the available alarm base station Earlier versions of the alarm base station had a range of up to 100m for others an external antenna FAZ HF permitted larger ranges The actual attainable distance between the transmitter and the receiver in normal operation greatly depends on the installation location and the surroundings As arule when mounted in a family home for example all the components should work properly and there should be no radio reception problems Other causes of reduced ranges All types of high frequency interference Any buildings or vegetation Conductive metal parts that are located near the devices or within or near their transmission path for example radiators metallised insulation glass windows reinforced concrete ceilings etc
10. er supply a Operation using batteries b Operation using a power supply Installation a Notes on selecting the installation location b Opening the casing of the FAZ SI 2 control panel c Installation Registering the siren control with the alarm base station a Preparing the alarm base station b Initial operation of the siren control c Enter a name for the siren control Programming a Conditions for setting off the alarm b Changing the alarm trigger settings c Setting the alarm duration for the external siren a d Setting the alarm duration for the external strobe aa Geils 25 Opening the housing of the siren control replacing the batteries 27 Maintenance and cleaning Disposal a General information b Batteries and rechargeable batteries Information on the range Technical specifications BGP WISI UCUONS Aere eh Ae ic pen ee EE ele ese companions a Registering the siren control with the alarm base station b Opening the casing replacing the batteries 1 Introduction Dear customer Thank you for purchasing this product This product meets the requirements of both current national and European guidelines In order to ensure continued fulfilment of legal requirements and safe operation of this product we kindly ask you to carefully follow the instructions in this user manual Please read the user manual completely and observe the
11. example with the time 16 30 14 12 and the date z Briefly press the Men a A button on the control troubles unit of the FAZ Z alarm base station Use the 4 and v buttons to select the sensors sensors menu Confirm your selection by briefly pressing the OK sensors button sensors add appears on the LCD add Press the OK button again sensor x The X character here stands for the number of clear sensors that have already been registered plus one Keep pressing the gt button until the display shown siren 1 on the right appears on the LCD clear IS Now the alarm base station is ready to receive the registration of the siren control FAZ 3000 SI 2 14 b Initial operation of the siren control Go back to the siren control and insert 4 type AA batteries into the 4 upper battery holders observing correct polarity see figure inside the battery compartment Then insert 4 type C batteries into the large battery compartment observing correct polarity see figure in battery compartment The siren control contacts the alarm base station by sending a radio signal The LED on the circuit board briefly lights up and the alarm base station emits a short signal tone to confirm signal reception If you also wish to use a power supply connect the BU1 socket see figure 1 on page 10 with the power supply s low voltage output IS The power supply mu
12. for the internally armed state Internally armed state Inthe case of an alarm the siren control will not set off an alarm when set to internally armed setting 0 Alarmwhen Alarmwhen Alarmupon Alarmupon Alarm upon int armed ext armed smoke sabotage attack detection The state is internally armed therefore triggering via the siren control when set to externally armed is impossible setting Ifa smoke detector sets off the alarm no alarm is effected via the siren control set to 0 Ifa sabotage contact sets off the alarm no alarm is effected via the siren control set to 0 In the case of an attack no alarm is effected via the siren control set to 0 19 Table of the factory settings for the externally armed state Externally armed state Alarmwhen Alarmwhen Alarmupon Alarmupon Alarm upon int armed ext armed smoke sabotage attack detection ee ee E N e The state is externally armed therefore triggering via the siren control when set to internally armed is impossible setting In the case of an alarm the siren control sets off an alarm when set to externally armed setting 1 If a smoke detector is triggered an alarm is set off by the siren control setting 1 If a sabotage contact is triggered an alarm is set off by the siren control setting 1
13. http www conrad com OPERATING INSTRUCTIONS amp 100 recycled paper Bleached without chlorine Imprint These operating instructions are published by Conrad Electronic SE Klaus Conrad Str 1 D 92240 Hirschau Germany All rights reserved No reproduction including translation is permitted in whole or part e g photocopying microfilming or storage in electronic data processing equipment without the express written consent of the publisher The operating instructions reflect the current technical specifications at the time of print We reserve the right to change the technical or physical specifications Copyright 2007 by Conrad Electronic SE Printed in Germany Version 01 07 CE FAZ 3000 SI 2 Wireless siren control Item no 75 03 37 This user manual belongs to this product It contains important information specific to its operation and handling Please bear this in mind when passing on the product to a third party Therefore keep this user manual for future reference A contents list can be found in the table of contents on page 2 QINRAD ELECTRONIC Table of contents C1 QUN gt 10 11 12 13 14 15 Declaration of conformity DOC Introduction Prescribed use z Scope On delivery Tie E eee eared ae athe 5 Explanation of icons Safety instructions a General information b Batteries and rechargeable batteries Operation using batteries and pow
14. ies must not be recharged They might explode If the device is not used for a longer period of time for example when stored remove the inserted batteries rechargeable batteries to prevent them from leaking and causing damage IS It is possible to operate the siren control with rechargeable batteries However due to the lower voltage rechargeable battery 1 2V battery 1 5V and the lower capacity the period of operation and the range are reduced In some instances powering with rechargeable batteries may not be possible when the siren control sends a battery empty message to the alarm base station even when the batteries are full therefore immedi ately generating a disturbance message Therefore to ensure safe operation only use high quality alkaline batteries 6 Operation using batteries and power supply a Operation using batteries Battery operation offers the benefit that the system can run fully independ ently when there are no power sockets available at the installation location The siren and strobe each version requires an operating voltage of 12V are also supplied with power by the siren control in the case of an alarm The drawback of battery only operation is that the wireless receiver in the siren control is not continuously switched on due to its high power consumption otherwise the batteries would be used up too quickly In order to reduce the amount of power that is used the radio receiver is on
15. layed Other device groups may be selected with the gt button siren control remote switch alarm dialler PC interface alarm base station When more than one siren control is registered select the siren control to be opened by using the 4 and buttons disarm I SA AG AL troubles service contact 1 livingr w1 siren 1 Housefront siren 2 courtyard 27 Confirm your selection by briefly pressing the OK button The casing of the selected siren control and the casing of a connected signal sender may now be opened without setting off a sabotage alarm You may now safely replace the batteries This way no data is lost and the sensor and device do not need to be re registered afterwards After inserting the new batteries the LED blinks 1 time briefly The radio connection to the alarm base station has been established and checked After replacing the batteries close the casing of the siren control Briefly press the OK button on the alarm base station to end the maintenance You are now in the sensor list again By using the 4 and buttons another siren control may now be selected or use the gt button to select another device group You can exit the service mode by pressing the C button three times This returns you to the normal display mode top level of the alarm base station 28
16. ly switched on for a short time every 5 seconds This means that in the case ofa alarm the alarm base station must transmit the radio signal for 10 seconds During these 10 seconds you cannot stop the alarm An alarm delay of approx 5 seconds is also generated IS Please observe the notes on rechargeable battery operation in section 5 b on page 7 b Operation using a power supply When operating with an additional power supply 12V 1A middle contact must be plus not supplied the receiver is continuously switched on The batteries serve primarily as an emergency power supply for instance in the case of a power outage IS Therefore batteries should always be inserted When the siren control uses an external power supply the alarm base station briefly sends a radio signal which immediately sets off the alarm 7 Installation a Notes on selecting the installation location The siren control should be installed in a dry indoor area notin a damp cellar or a bathroom for example Choose a secured area so that intruders cannot quickly tamper with the device The installation location should neither be immediately visible from outside the house nor from within the house In a single family house the attic is a good location For example the siren control can be installed on the inside of a house wall In order to ensure sabotage protected wiring the connector cable is fed into the back side of the siren cont
17. rol casing If you drill the hole for the wiring of the siren or the strobe directly outwards through the wall behind the siren control the cables are not accessible The cable is fed outward through the hole in the wall The combination signal siren and strobe is installed outside such that the cables lead directly into the casing of the device and are therefore not accessible Do not install the device in the immediate vicinity of large metal objects radiators mirrors aluminium laminated walls insulating cladding metal doors as this can reduce the wireless range If you are using a power supply unit to supply the power a socket 230V 50Hz must be located near the installation location b Opening the casing of the FAZ SI control panel All larger casings of the FAZ 3000 wireless alarm system are comprised of a front shell and a rear shell which are connected by 2 catches on the right side Acatching system on the left side of the casing which is comprised of catches on the front shell and catch slots on the rear shell serves to close the half shells Using a flat screwdriver carefully push the two catches approx 1 millimetre inwards until the half shells separate First press one catch inwards and pull the casing approx 1 2 millimetres apart at this location Then press the other catch inwards the casing now opens Do not straighten any of the components or additional PCBs just so that it looks bet
18. safety and operation instructions before using the product All company and product names contained herein are trademarks of their respective owners All rights reserved Should you have any further questions please contact our technical service Germany Tel no 49 9604 40 88 80 Fax no 49 9604 40 88 48 Email tkb conrad de Mon to Thur 8 00am to 4 30pm Fri 8 00am to 2 00pm 2 Prescribed use The wireless siren control FAZ 3000 SI 2 is only suitable for use with the wireless alarm system FAZ 3000 An additional siren with or without strobe each must be ordered separately neither included in delivery may be connected 12V versions required The power supply of the siren control can be provided either exclusively by batteries or by using a power supply in addition to the batteries No part of the product may be modified or adapted The device may only be operated when its casing is fully closed The product is only suitable for use in dry and closed indoor rooms Make sure it does not get damp or wet Any use other than the one described above may damage the product and can also increase the risk of short circuit fire electric shock etc All the safety instructions and installation notes in this manual must be observed without fail 3 Scope of delivery e Wireless siren control FAZ 3000 SI 2 Assembly material User manual 4 Explanation of icons The icon with a lightning
19. siren 2 courtyard disarm 17 47 15 12 11 Maintenance and cleaning The product requires no servicing except for battery replacement Any repairs should be carried out by a skilled technician or a professional workshop Clean the product with a soft clean dry and lint free cloth To remove heavier dirt use a cloth which is slightly moistened with lukewarm water Do not use any solvent based cleaning agents as these may damage the plastic casing 12 Disposal a General information When the product is no longer usable dispose of it in accordance with the applicable statutory regulations b Batteries and rechargeable batteries As the consumer you are legally obliged to return all your used batteries and rechargeable batteries Do not dispose of your used batteries via the household rubbish Batteries rechargeable batteries containing harmful substances are marked with the following icons which alert you to the fact that disposal via the household rubbish is prohibited The identi fiers for the respective heavy metals are Cd cadmium Hg mercury Pb lead identifier is on the battery rechargeable battery for example under the rubbish bin icons on the left You can return your used batteries rechargeable batteries free of charge to any authorised disposal station in your area in our stores orin any other store where batteries rechargeable batteries are sold By doing so you comply with your leg
20. st provide an output voltage of 12V DC voltage and a current of at least 1A The middle contact of the low voltage plug must be plus the outer contact minus Close the casing of the siren control The two faceplates must audibly click in Plug the power supply into a socket 15 c Enter a name for the siren contro e Return to the alarm base station The LCD s display has changed See the figure on the right The number 1 is the number of the siren control siren 1 The appropriate number is displayed depending on the number of siren controls that have already been registered With the buttons on the alarm base station enter a name for the siren control for instance Hdousefront for front of house facing street or siren 1 Housefront_ similar gt Toenter letters use buttons 2 9 each represent ing multiple letters click through as with a mobile phone by repeated quick pressing of the same button gt Numbers and umlauts can also be found on the buttons gt Use the 0 button to enter a space character gt Special characters can be entered using the 4 and buttons gt To switch between capital and lower case letters use the button Men a A gt The cursor automatically jumps to the next position approx one second after the last button was pressed gt Youcan use the C but
21. tects the siren control in the event of an overload it shuts down the external siren strobe The maximum power consumption of the external siren and the external strobe combined may not exceed 0 8A for example strobe 0 2A siren 0 6A Battery compartment for 4 AA batteries Terminals KL1 KL2 and KL3 KL1 Connection for a sabotage contact of the external signal sender if using the connection the jumper must first be removed KL2 Connection for external siren 12V left right KL3 Connection for external strobe 12V left right Hole for wall mounting screw hole 11 c Installation The installation of the siren control onto a wall is accomplished with 3 screws and dowels supplied In order to ensure a sabotage safe laying of the cables between the siren control and the siren strobe B the hole should be drilled outwards to the siren strobe exactly behind the casing ofthe siren control see figure 2 The siren strobe will be positioned precisely over the hole thereby making the cables inaccessible di The siren strobe must be installed at a height that is well out of reach Otherwise for example the device could covered Figure 2 with spray foam insulation thereby making the alarm virtually inaudible At the desired installation location attach two screws horizontally and 80mm apart Depending on the state of the wall you ma
22. ter The design of the components of newer versions of the siren control are subject to change E G TA1 D H C B gogo dod Connectors for B or z external siren and external flash A EEE e Figure 1 10 Battery compartment for 4 type C batteries BUT socket for external power supply 12V 1A middle contact must be plus the outer contact is the earth GND The power supply can be used in addition to the batteries thereby extending battery life batteries then serve only as an emergency power supply during power outages LED for data transfer display TAT button for sabotage contact The button is pressed by the upper shell of the casing when the casing is closed If the casing is opened without authorisation the alarm base station sends a sabotage alarm When you want to open the casing to replace the batteries for instance the alarm base station must first activate the maintenance mode for the respective siren control Fuse SI1 1A 250V slow blow This fuse protects the external power supply from overload Fuse SI2 0 8A 250V slow blow The second fuse pro
23. ton to delete a character you entered incorrectly by mistake Once you have entered the name you require iren 2 press the OK button Now you can switch on Site clear another siren control see page 15 Press the C button three times to exit the alarm base station s registration mode You are in the normal display mode again top level disarm 16 45 14 12 16 9 Programming IS The programming must take place at the alarm base station FAZ 3000 2 Settings for when the siren control should be triggered and when connected siren strobe should be activated are entered at the alarm base station FAZ 3000 2 IS For example the siren control could be activated when a smoke alarm goes off or when the remote control FAZ 3000 FB is used to trigger an alarm during an attack In addition the duration of the alarm s siren and strobe can be set The following settings are controlled from the alarm base station e Conditions for setting off the alarm Alarm for internally armed externally armed smoke sabotage attack e Alarm duration for siren The maximum alarm duration for an acoustic alarm that is generated by a siren outside is restricted by law to 3 minutes an external strobe light can signal for longer This may vary at health resorts for example As a precaution check this out with your local council e Alarm duration for strobe light The fac
24. tory default setting for the alarm duration of the external strobe is 20 minutes you may adjust this time to any duration between 1 and 100 minutes 17 a Conditions for setting off the alarm For an external siren the conditions for setting off an alarm can be adjusted in detail and depending on the states disarmed internally armed and externally armed Useful settings are already preset in the factory however you can change these settings to suit your own personal requirements IS The factory default is For externaly armed the siren control is only activated when nobody is at home For internally armed and disarmed the siren control is not activated If required however this can be changed Table of the factory settings for the disarmed state Disarmed state Alarmwhen Alarmwhen Alarmupon Alarmupon Alarm upon int armed ext armed smoke sabotage attack al Setting off the siren control with internally armed and externally armed is not possible because of the current disarmed state each set to If a smoke detector sets off the alarm no alarm is effected via the siren control set to 0 Ifa sabotage contact sets off the alarm no alarm is effected via the siren control set to 0 In the case of an attack no alarm is effected via the siren control set to 0 18 Table of the factory settings
25. tween 60 wh 1 and 100 minutes in increments decrements of 1 i minute To make a quick setting keep the 4 or w button pressed for a few seconds 25 Pressing the OK button applies the setting Exit the menu by pressing the C button twice This returns you to the normal display mode top level 26 ext siren dur flash disarm 22 10 08 02 10 Opening the housing of the siren control replacing the batteries Before the casing of the siren control FAZ 3000 SI 2 may be opened the alarm base station must place it in maintenance mode Otherwise the alarm base station immediately sets off the sabotage alarm when the casing is opened IS The same is of course true when the casing of the external signal sender with siren and strobe are to be opened if the sabotage contact is connected inside the siren control to terminal KL1 To place the siren control in maintenance mode proceed as follows The alarm base station must be in the top level The LCD should appear as on the right for example with the time and the date Briefly press the Men a A button on the control unit of the FAZ Z alarm base station Use the 4 and buttons to select the service menu See the figure on the right Confirm your selection by briefly pressing the OK button The first sensor that was registered with the alarm base station is disp
26. y apply here too To set the alarm duration for the external siren which is connected to the siren control proceed as follows The alarm base station must be in the top level The LCD should appear as on the right for example with the time and the date Briefly press the Men a A button on the control unit of the FAZ Z alarm base station Use the 4 and buttons to select the ext siren external siren i e the siren control itself Confirm your selection by briefly pressing the OK button the LCD display appears as shown in the figure to the right Select the menu dur siren alarm duration for external siren by using the 4 and buttons disarm 21 57 08 02 troubles ext siren ext siren trigger siren siren ext dur 23 24 Confirm your selection by briefly pressing the OK button The alarm duration that is currently set for the external siren that is connected to the siren control appears on the LCD factory set to 60 seconds Use the 4 and buttons to select the required alarm duration You can set the duration to a value between 10 and 300 seconds in increments decrements of 10 seconds To make a quick setting keep the 4 or button pressed for a few seconds Pressing the OK button applies the setting Exit the menu by pressing the C button twice
27. y also need to drill holes and insert dowels When drilling or fastening screws be careful not to damage any power supply lines gas or water pipes as this could pose a life threatening danger Then use a suitable screwdriver to screw in the two screws Make sure that there is a distance of approx 3mm between the lower side of the screw head and the wall See figure 3 BY 3mm Mount the siren control on the 2 screws Figure 3 The third screw must be screwed in from the inside through an opening in the lower part of the casing IS This way the siren control cannot be removed from the wall without opening the casing if casing is opened a sabotage alarm is sent by the alarm base station 12 Depending on the wall drill a hole for the third screw and insert a dowel Mark the position for the drill hole using a ballpoint pen refill or a nail for example Then remove the siren control from the wall drill the hole and insert a dowel When drilling or fastening screws be careful not to damage any power supply lines gas or water pipes as this could pose a life threatening danger Afterwards the cables can be fed through the opening in the back side of the siren control and connected to the appropriate terminal KL1 sabotage contact for the siren strobe casing first remove factory installed jumper KL siren and KL3 strobe Make sure to connect the wires correctly observe correct polarity plus
Download Pdf Manuals
Related Search