Home

View User Manual - Evans Custom Amplifiers

1. ant Here are a few tips we have learned from our customers over the years NORMAL AND 6db INPUTS 6db provides the most volume with a heavier amplified sound Use the NORMAL input with strong pickups to avoid overdriving the preamp MASTER Used to set the output gain of the preamp The convenient ON OFF switch is activated when this control is rotated CW Since the switch activates between 2 and 3 the part of the rotation between 3 and 10 is used for level control BUFF This control provides beautiful harmonically rich overtones for the solid state preamp that are usually only found in tube preamps Start with BUFF on 4 6 next adjust TREBLE and EXPAND REVERB Adjusts the mix of reverb and bypass signal to give the degree of reverb desired For very wet reverb place REVERB at maximum REVERB SELECTION SWITCH Located on the rear panel this switch selects one of three reverbs Reverb alone reverb plus flange and reverb plus chorus Flange is achieved by splitting the audio signal into two parts and introducing a variable phase shift in one path before recombining the signal The chorus effect is similar except the delay introduced is rapid and random REVERB DWELL CONTROL Also located on the rear panel the variable control sets the room size or decay time for the selected reverb Switch to Reverb Flange with Dwell CW just past center detent for a thicker tone BASS The maximum BASS is dialed in by playing the lowest open string while
2. ects units should be connected here However some effects may operate better connected between the instrument and NORMAL input PREAMP OUT This is an unbalanced line out signal for driving a mixer board or an additional power amplifier Level is independent of MASTER control EXTERNAL SPEAKER The output is used for driving an external 8 ohm speaker For the AH200 the combined load of speakers should not be less than 4 ohms PHONES Jack designed for stereo headphones 40 Ohm impedance nominal When phones are plugged in all speakers are switched off GENERAL SETUP Combo amp suggested settings MASTER BUFF REVERB BASS DEPTH BODY EXPAND TREBLE VOLUME INPUT RE300 Soft 3 5 2 4 2 3 2 3 50 3 50 1 2 3 5 NORMAL 10 SPKR Med 4 6 3 5 3 4 5 70 7 50 2 3 5 7 NORMAL Loud 5 7 4 6 4 5 5 7 75 6 75 2 5 4 6 6dB SE300 Soft 3 4 3 5 3 4 1 3 50 3 5 50 1 2 3 5 NORMAL 15 SPKR Med 4 6 2 5 4 6 5 6 70 6 7 70 1 3 5 7 NORMAL Loud 5 7 4 6 4 7 6 8 75 6 8 75 2 5 4 6 6dB For the AH200 use suggested settings according to the closest speaker size For maximum sweetness use lower settings for Master Bass Depth Treble and Volume on 500 Watt amps TROUBLE CHECKS Sometimes checking a few basic things can solve problems To save time and money please check the troubleshooting tips below before you call for help or ship your amp back to us for repair If repair should be necessary and the amplifier is under warranty we prefer it to be sent
3. erms and conditions take precedent over all other terms and conditions warranty statements or policies
4. ord into them the effects send and return 6db and normal jacks You may also need to spray one spray of a non residue fast drying electronics cleaner into each jack then plug into and out of each jack The contacts inside of the jacks may have gotten oxidation on them Also you could try jumping out the effects loop To do this plug a known good guitar cable into the effects send and return jacks If this fixes the problem then clean or replace the effects jacks Amp Cuts Out Your power amp may be protecting itself from damage that can result from loud distortion or tone settings that are not optimized for your required application Another possibility is a loose connection so call us after rereading the owner s manual Need Amp Repair Five decades of good customer service has revealed that most problems are quickly fixed with a phone call Also we can better assist you if we know your amp s serial numbers Please give us your phone number and best times to call along with the serial numbers on the preamp and power amp so that we can better assist you We will be glad to help you by phone Note There are no user serviceable parts inside the chassis Only a qualified service technician can properly determine the course of action beyond the above checks DPU300 and AH200 Digital Power Units The DPU300 s internal power amp produces 300 Watts rms into 4 ohms at 0 1 THD The AH200 contains a digital power amplifier providing 200 Watts
5. out warranty However Evans will supply any parts deemed necessary by Evans for repair at a nominal cost not including shipping This warranty does not apply to any product damaged by accident misuse abuse improper voltage product modification neglect faulty installation or operation improper maintenance rental or any shipping damage lightning or other acts of God This warranty does not apply to any parts for service by anyone else other than Evans Custom Amplifiers or their authorized service technician This warranty is in lieu of all other warranties expressed or implied and Evans Custom Amplifiers makes no further warranties expressed or implied including but not so limited any warranties of merchantability or fitness for any particular purpose It is expressly agreed that the Buyer User shall have no claim against Evans Custom Amplifiers with respect to either personal injury or damage to property or loss of profit resulting from any defect or for any consequential damages such as but not so limited loss of business opportunities property or personal injury losses etc or for any indemnity implied or expressed with respect to claims by third parties And Buyer shall indemnify Evans Custom Amplifiers against any and all claims by third parties against Evans Custom Amplifiers resulting from the use of equipment and or materials purchased hereunder or from the use of any products made from or by said equipment or materials These t
6. owe AMPLIFIERS OPERATING INSTRUCTIONS AND USER MANUAL EVANS CUSTOM AMPLIFIERS Inc 2734 Woodbury Drive BURLINGTON NC 27217 Phone Fax 336 270 5700 Web www EvansAmps com 09 09 2013 Starting in 1962 Evans has been building amplifiers that deliver the finest in stringed instrument amplification Our founder Jim Evans is an industrial electronics engineer and a professional steel guitar player He recognized that no amplifier on the market filled his exacting need for quality of tone So he started building amplifiers for his own use Every few weeks a musician would make him an offer for his amp After letting the amp go that night he furiously worked to build another so he could play the next weekend Thus began our company Through the years the electronic design has been refined with new technology being embraced at every opportunity Whether you play jazz guitar steel guitar finger style rhythm or lead guitar fiddle or keyboard Evans will give you a tonal quality that is beyond compare Scot and Julia Buffington OPERATING INSTRUCTIONS Evans amplifiers are designed to reproduce the true sound of your instrument You will find the controls easy to adjust by using the following outline to get you started You may use the entire span of the control if necessary For instance there is no rule that says you must have the Reverb control at 6 or Bass at 3 Make use of all the controls and inputs to achieve the sound you w
7. rms output at 0 2 THD into 4 ohms The output is bridged and not referenced to common or circuit ground Therefore connect only a speaker load with polarity to amp to Any other load or appliance that causes output current to flow to ground will cause the amplifier to permanently fail If the output leads are shorted together the amplifier may recover from the fault by removing the load and turning the amplifier off for several seconds If the condition that caused the fault has been removed proper operation of the amplifier will be restored Internal Transformer The internal transformer supplies 28 Vac to the preamplifier and is configured to operate the entire unit from nominal voltages of 85 to 250 Vac WARRANTY Evans Custom Amplifiers warrants this product to be free from defects in material and workmanship for a period of three years from the date of delivery to the original consumer purchaser Evans Custom Amplifiers will pay all labor and material expenses for all repairs covered by this warranty The Buyer is responsible for arranging its transportation for repair risk of transport and payment of any shipping charges In addition proof of date of purchase may be necessary in order to obtain warranty repair All shipping risk of transport and cost of repair and or replacement work of any product made AFTER the above stated warranty period shall be the responsibility of the Buyer Sales outside the US are sold as is with
8. to us for evaluation and repair No Power If pilot light on the preamp is out first check the power cord and cord connections For console amplifiers check the 28 Vac connections from the power amplifier to the rear of the preamp No Sound No sound from the speaker although the pilot light is on First unplug any external speaker then reset the power amplifier by turning off power wait a few seconds for the pilot light to go out and then turn the power back on If the sound returns check the external speaker and cord for shorts Second make sure the Drive cable is completely plugged into the preamp s drive output and DPU unit Next check with stereo headphones for sound If the headphones are working then check internal speaker and wiring If there is no sound in the headphones use a Digital Multi Meter to check the 10K ohm Master potentiometer If the pot checks good insert a known good guitar cord into the send and return jacks If the amp now works you should clean or replace your effects loop jacks Hum and Other Interference Check guitar signal cord or effects cords for open shield connection Check the output jack on guitar for broken ground or signal connection Check room light dimmer circuits as source of radiated hum Do not place cell phones on the amplifier Keep single coil pickups a reasonable distance away from the amp Amp Volume Fluctuates You may need to clean the 1 4 jacks by plugging and unplugging a guitar c
9. turning the control CW from 0 until it gets boomy Then back off by a number Turn down BASS when using 6db INPUT with MASTER greater than 6 or NORMAL INPUT with MASTER greater than 7 Remember the louder you play the less BASS you need If the BASS is turned up at loud volumes the low end will be over compensated and muddy because bass frequencies are easier to reproduce at loud volumes DEPTH This control enhances the low and low mid range Adjust from 12 to 3 o clock to balance the volume between your guitar s low E and A string BODY control must be greater than 1 for this control to be effective BODY Used to set the mid range and darkness of the sound This is a multifunction control that increases low midrange tones while rolling off high frequencies Adjust from 2 to 10 for best tone and to allow for Depth control operation EXPAND This control boosts the highs and some low tones CCW is off Turn to 12 to 3 o clock for most instruments TREBLE Sets the amount of treble desired Playing the highest open string and turning up the control from O until it gets thin and then backing off a number should find maximum TREBLE VOLUME Sets the input level to the preamp Lower settings 3 5 mimic the instrument s voice higher settings 6 9 emphasize the amplifiers tone settings EFFECTS SEND AND RETURN These jacks are located on the back panel of the preamplifier In the signal path they are situated after all tone controls Most eff

View User Manual - Evans Custom Amplifiers

Contents

Download Pdf Manuals

Related Search

Related Contents