Marmitek LMM21 user manual
Contents
1. modified without prior notice LMM21 13 Environmental Information for Customers in the European Union European Directive 2002 96 EC requires that the equipment bearing this symbol on the product MMM and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product 14 HAIBRAIN DECLARATION OF CONFORMITY Hereby Haibrain BV declares that this LMM21 is in compliance with the essential requirements and other relevant provisions of the following Directives Directive 2004 108 ec of the european parliament and of the council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2006 95 EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage2. 10 signals are attenuated by devices and lights which are connected to the power line In a normal home situation this effect is negligible the Haibrain X 10 system is using active gain control to eliminate the effects However it is possible that a particular device in your house is attenuating the signals so much that the range of Haibrain X 10 signals is decreased significantly When you have range problems it is wise to try to locate the device which is attenuating the signals simply by unplugging devices from the power line and testing the differences in range for your Haibrain system When e g your conclusion is that e g your computer monitor is attenuating the signal you can use a FM10 LMM21 5 Plug in Filter between the power line and the monitor to eliminate the effects Known devices which can cause attenuation are PC Monitors PCs with heavy internal power supplies Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps Energy Saving Lamps 3 Some old devices are able to disturb the signal by transmitting noise on the power line Because the Haibrain X 10 signals are transmitted on 120 kHz only noise on or near this frequency will have influence on the range When you use a FM10 Filter to connect this device to the power line the noise will be filtered 4 The Haibrain X 10 protocol has several mechanism to avoid modules to be switched on or off by other sources than your Haibrain X 10 Controllers How
3. ES Up to a maximum of 256 different addresses can be preset These are subdivided into a so called HouseCode A to P incl and a UnitCode 1 to 16 incl The HouseCode can also be set on the controllers so that the controllers and modules become part of the same system The address can be set either using code dials or by pressing buttons depending on the type of module The Haibrain X 10 System uses standard commands which control all units with the same HouseCode at the same time e g all lights on all units off etc 4 HAIBRAIN SIGNAL RANGE Range of Haibrain X 10 signals over the Power Line and how to increase the range The Haibrain X 10 System is based on power line communication The range of the Haibrain X 10 signals very much depends on the local circumstances On average the range is a cable length of 80 meters If you have difficulties with the range of your Haibrain X 10 signals please pay attention to the following facts 1 When more than one phase is used for your electrical system it is necessary to couple these phases for the Haibrain X 10 signals For coupling you can use FD10 Phase Couplers Filters You only need to install a Phase Coupler Filter when your wall outlets and light switches are divided over more than one phase more than one group is no problem For bigger buildings or longer distances we advice you to use an active repeater instead of passive FD10 s 2 It is possible that Haibrain X
4. LIVIM2 1 Dimmer Micromodule 1 load haibraf 20433 20111202 LMM21 a ALL RIGHTS RESERVED HAIBRAIN only brilliant ideas TABLE OF CONTENTS TABLE OF CONTENTS 2 SAFETY WARNINGS HOW DOES HAIBRAIN X 10 WORK ADRESSES orden s4 SIGNALE RANGE erronee deer ener re erase 5 ONE LOAD DIMMER MICRO MODULE 7 FUNCTIONS wis INSTALATION fs niger guapo Seen aeri seht nens 9 PROGRAMMING 10 FREQENTLY ASKED QUESTIONS s TECHNICAL DATA e nenne DECLARATION OF COPYRIGHTS pe D 2 HAIBRAIN SAFETY WARNINGS LMM21 The wiring of your electrical installation is live 230 V and extremely dangerous Never connect the module when plugged into the mains Always turn off the main switch before starting the installation This product is for professional use and should be installed by a certified installer To prevent short circuits this product should only be used inside and only in dry spaces Do not expose the components to rain or moisture Do not use the product close to a bath swimming pool etc Do not expose the components of your systems to extremely high temperatures or bright light sources In case of improper usage or if you have altered and repaired the product yourself all guarantees expire Haibrain does not accept responsibility in the case of improper usage of the product or when t
5. M21 does not have code wheels To change the address the module needs to be set to the program mode Press and hold the Program button for 5 seconds indicator light flickers once the controlled light Turns ON means entering Program mode Then you transmit the address command at this time the indicator light goes OFF and controlled load goes OFF Warning The MicroModule will leave the setup mode if it doesn t receive any commands within 30 seconds 10 HAIBRAIN FREQENTLY ASKED QUESTIONS What is the reason for modules to switch on off spontaneously It is possible that a Haibrain X 10 System is installed at one of your neighbours using the same House Code To solve this problem try to change the House Code of your system or have FD10 Phase Coupler Filter installed at your incoming mains My modules will not respond to my controller Make sure that the House Code on all Modules and Controllers are set to the same House Code A P My modules will not react to my remote sensor When you use a remote or sensor you should have at least one Transceiver CM15Pro or Haibrain X 10 Security Console installed in your house These components will translate the radio signals to the Haibrain X 10 signal on the power line Using several remotes and sensors you only need one central transceiver LMM21 11 Am able to increase the range of my remotes by using more Transceivers Yes you can use more than one Transc
6. eiver in your home when the range of your remotes is not sufficient The transceiver is using so called collision detection to prevent signals to be disturbed when more than one transceiver is transmitting The Transceivers will wait for a quite power line before transmitting their data To prevent your Haibrain X 10 System to become slow or to prevent dimming from becoming less smooth make sure that the transceiver units are placed as far away from each other as possible Do you have other questions that have not been resolved by the above information Please go to http www haibrain com 12 HAIBRAIN TECHNICAL DATA Supply voltage Power Consumption Making capacity Control Load QTY Dimmable Signal sensitivity X 10 Key codes to respond to Input switch Use in 3 phase installation Connections control lines Ambient temperature Dimensions 230VAC 10 10 50 Hz lt 1W 60W 230V to 300W 230V for incandescent lamps and Eco halogen light One Yes better than 25 mVpp at 120 kHz All units Off All Lights On On Off DIM BRIGHT Extended Dim 1 way standard rocker switch 1 way momentary switch normally open contact FD10 3x or FKX40 necessary Wire for a standard rocker switch or momentary switch and connecting clamps for phase and switched phase not more than 1 meter between the micro module and the switch 10 C tot 50 C Operation 43 25mm x 47mm x 21mm Specifications may be
7. ever it is possible that the Haibrain X 10 signals are disturbed by e g baby phones which are in TALK mode continuous transmission When these kind of signals are present on the power line it is possible that the Haibrain X 10 signals will not come through 5 The mains do not stop at the front door of your home Everything that is attached to mains nearby your home can have influence on Haibrain X 10 signals e g heavy machinery If you think that your system is influenced by devices out of your house it is advisable to install FD10 Phase Coupler Filter on each phase entering the house These filters will block signals coming into or going out of your house but will also match the impedance for the mains Hereby make your house Haibrain X 10 compatible for these units The FD10 s will not only filter but will also couple the phases please see 1 6 HAIBRAIN ONE LOAD DIMMER MICRO MODULE YELLOW T e YELLOW Program RED o RED Button BLACK BLACK Light Indicator Dimmer Micromodule 1 load LMM21 Dimmer Micromodule 1 load SOS TTE ES E 9 FUNCTIONS Remote control Off and Dim e Suitable for 230V and Eco halogen lighting e Remote control via the mains using Haibrain X 10 Commands and with one or more momentary switches Switches and dims lighting circuits up to 300W e be used in combination with designer switching material e start and smooth dimm
8. he product is used for purposes other than specified Haibrain does not accept responsibility for additional damage other than covered by the legal product responsibility This product is not a toy Keep out of reach of children Do not open the product the device may contain live parts The product should only be repaired or serviced by a qualified expert Automatic switching devices provide comfort but can also be dangerous They can surprise people or can ignite clothing hanging over an electric heat source Please be careful and take appropriate measures to avoid accidents HOW DOES HAIBRAIN X 10 WORK Haibrain X 10 components use the existing mains wiring to communicate using Haibrain X 10 signals You can build a complete system using the three different kind of components of the Haibrain X 10 System 1 Modules These components will receive Haibrain X 10 signals and will switch or dim the attached lamp or appliance Examples of these modules are lamp modules and appliance modules These are available as build in micro DIN rail and plug in modules 2 Controllers These components will transmit Haibrain X 10 signals and thus will control the Modules 3 Transmitters Wireless components like remotes The signals of these components will be received by a controller with transceiver functionality IRRF 7243 TM13 CM15Pro The Transceiver will translate the signals into Haibrain X 10 signals on the power line ADRESS
9. ing features remembers the last dim setting Makes your X 10 system invisible No extra wires required for installation Dimmer 60W 300W setting Can be regulated from 0 lighting to the desired dim The module is not suitable for dimming and controlling LMM21 7 low energy light bulbs and tube lighting An Appliance module should be used for these devices HAIBRAIN INSTALATION Switch off appropriate mains fuse master switch e the wall switch out of the wall box Disconnect all wires from the switch Connect the phase and load wire to the L and 1 terminals of the micromodule Connect the thin Black and Red wires of the built in module to the wall switch Connect the thin Black and Yellow wires of the built in module to the 1 way momentary switch normally open contact the MicroModule against the back wall of the wall outlet behind all the wires You are now able to program the MicroModule For more information see chapter Programming Install the wall switch at its original place after the MicroModule is programmed e Please note due to heat generation apply no more than one module per flush socket central socket LMM21 PROGRAMMING WARNING DO NOT FORGET TO TURN ON THE MAIN MASTER SWITCH PRIOR TO PROGRAMMING Programming the address The factory setting for the LMM 21 is to address 1 Unlike most Haibrain X 10 Modules the LM
10. limits Directive 2002 95 EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment HAIBRAIN BV P O BOX 9301 3506 UTRECHT NETHERLANDS LMM21 15 COPYRIGHTS Copyright and all other proprietary rights in the content including but not limited to model numbers software audio video text and photographs rests with Haibrain B V Any use of the Content but without limitation distribution reproduction modification display or transmission without the prior written consent of Haibrain is strictly prohibited All copyright and other proprietary notices shall be retained on all reproductions 16 HAIBRAIN haibrafn only brilliant ideas
Download Pdf Manuals
Related Search