PT7200 User Manual
Contents
1. GPS ID GPSID Annunciation GPS GPS Time Annunciation The dealer can program the following functions Null No Function is programmed Chan Annunciation Pressing this key to switch on and off the channel annunciation function Whisper After pressing this key receiver also can hear you even you speak lightly Press key again will disable the whisper mode Talk Around After pressing this key the radio will transmit with the RX frequency EAL CALL 1 CALL 2 CALL3 CALL4 Press the side button setas CALL 1 CALL 2 CALL3 CALL4 to transmit the stored coding Lone Work When the radio is set in Lone Work it will sounds pre alert tones before the Lone Work time expires and the user should press any key on the radio within the Reset Time indicating the user is safe otherwise the radio will activate emergency alert automatically Emergency Alarm When you press the top button setas Alarm the radio can sound alarm tone or transmit ID code or background tone to your partners or the system both of which can be chosen in radio programming by PC software Cancel Emergency Alarm Press the top button set as Alarm to cancel Emergency Alarm Man down Alarm Press this key to enter man down alarm mode which is optional function Scan A Press the button set as Scan to start scanning When in scanning the radio checks signals on each channel it stops scanning and pauses on the channel on2. latitude altitude etc to the remote control center The control center can also realize inquiring and group management on your radio s Please contact your dealer for details xKfr7 uUrn DECLARATION KIIS Un OF CONFORMITY CE 1588 We Kirisun Electronics Shenzhen Co Ltd 6 F Bldg H 2 East Industrial Zone Of Overseas Chinese Town Shenzhen 518053 China Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive 1999 5 EC and that any applicable Essential Test Suits measurement have been performed Description of equipment FM Handheld Transceiver Model No PT7200 This compliances is based on conformity with the following harmonised standards or documents 1 ETSI EN301489 1 V1 6 1 2004 12 2 ETSI EN301 489 5 V1 3 1 2002 08 3 ETSI EN300086 1 V1 2 1 2001 03 4 ETSI EN300086 2 V1 1 1 2001 03 5 EN60950 2001 A11 2004 Shenzhen 10 Oct 2007 WenLiang Fu Place and date of issue General Manager AR Signature Kirisun Electronics Co Ltd
3. KIr17 Un KIIS UN INSTRUCTION MANUAL PT7200 FM HANDHELD TRANSCEIVER CE O n TAEL faaan lS NOTE KMIZUN MISUN INSTRUCTION MANUAL PT7200 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing va brand two way radios produced by Kirisun Electronics Shenzhen Co Ltd We believe 22 two way radio which always incorporates the latest technology can bring great convenience to your life and work We also believe that the quality and function of eva two way radio can meet your demands for reliable communication PRECAUTIONS Please observe the following precautions to prevent fire personal injury and radio damage Do not operate your radio while taking on fuel or being charged Do not expose the radio for a long period to direct sunlight nor place the radio close to heating appliances Do not place the radio in excessively dusty areas humid n CAELI D Cg ti areas oron unstable surfaces Do not modify this radio for any reason Refer service to qualified licensed or certificated technicians only Notice to the User Government laws prohibit radio communication without permission in government districts Illegal operation is subject to punishment by fine and or imprisonment Refer service to the well trained professional technicians only Safety It is important that the user is aware of and understands
4. List Voice Annunciation Chinese English QT DQT QT DQT Battery Save Decode Encode Power Transmitting Receiving Channel Frequency Frequency Channel User m Spacing Solution OFF 1 1 1 2 L1 1 4 o 3 Auxiliary Function Button Settings Top Button Null Channel Annunciation Whisper Talk around CALL 1 2 3 4 Lone Work Emergency Alarm Cancel Emergency Alarm Man down Alarm N a ja jA V N EL ON Scan Temporarily Delete Noise Channel Transport High Low Power Switch Squelch Level Check Monitor Momentary Call Cancel Monitor Call Cancel Squelch Momentary Call Cancel Squelch Call Cancel Key Lock Compander Scrambler Battery Power Check Rental Time Check Side Button 1 Null Channel Annunciation Whisper Talk around CALL 1 2 3 4 Lone Work Man down Alarm Scan Temporarily Delete Noise Channel Transport High Low Power Switch Squelch Level Check Monitor Momentary Call Cancel Monitor Call Cancel Squelch Momentary Call Cancel Squelch Call Cancel Key Lock Compander Scrambler Battery Power Check Rental Time Check GPS GPS Posit
5. STALLING REMOVING THE BELT CLIP Match the grooves of the belt clip with those on the rear of the battery Then press the belt clip downwards to lock it in place To remove the belt clip use your nail or a tool to lift the metal spring piece in the belt clip from the topside and then pull the belt clip away from the radio Kdr7 Un D LED Indicator Lights red when transmitting lights green when receiving Flashes orange when receiving the identical 5 Tone Signalling Flashes red when battery power appears low Channel Selector Rotate to select channel 1 16 8 Power Volume Knob Turn clockwise to switch on the radio Turn counterclockwise till a click is heard to switch off the radio Rotate to adjust the volume after turning on the radio PTT PUSH TO TALK Button To make a call press and hold the PTT button then speak into the microphone in normal voice Release the PTT button to receive signals P CAEL amp Side Button 1 Programmable Button 6 Side Button 2 Programmable Button Top Button Programmable Button Speaker Microphone Jacks Used to connect the optional speaker microphone E BASIC OPERATIONS Switch On Switch on the radio by turning the Power Volume switch clockwise till a click is heard then the radio will be in the state of stand by and you will hear a beep if the dealer has set it And th
6. Tone 5 Tone Signalling will be transmitted when making a call Or transmit 5 Tone signal by pressing the Call 1 2 3 4 button which can be set by the dealer P CAEL 2TONE Signalling This function can be enabled or disabled by dealers through programming software 2Tone has 4 systems the single tone continuous time such as first tone or second tone could be set by the dealer 1 2Tone decode If the received 2 tone is same as the template chosen then it can decode successfully After the radio received the correct 2 tone signaling according to the Receive squelch mode set by the user the squelch will be ON Then the radio can receive the call and the orange LED light flashes After decoding successfully the radio can work according to the decode call response set by the dealer 2 2Tone encode The encoding template is set in the 2 tone call list The details must be set if encoding is ON The radio transmits the 2 tone signaling when the programmed call button is pressed The side button could be programmed as Call1 2 3 4 This function is programmed by the dealer MDC Signaling This function can be enabled or disabled by the dealers through programming software MDC has 4 systems in which different main ID group ID etc could be set by the dealer 1 MDC decode The option MDC system can be set through the RX signaling n CAEL KMIZUN system in the personal template If the rec
7. arge switched on or replace the battery pack 2 The battery ms l B MAJOR SPECIFICATIONS power consume The battery life is finished please replace it quickly after with a new battery pack PT7200 charging usos QT DOT Signalli Frequency Range 1 136 174 2 400 470 e frequency or ignallings are no 3 Cannot talk to or y gna ing MHz 8 450 520 hear others in identical and please reprogram it your group Make sure the SP un mute setting of the 4 350 400 selective Signalling 5 Tone in user solution is RF Power 5W H 1W L 4W H 1W L proper Out of the communication range Spurousiand Harmonics S lt 70 dB Frequency Stability 2 5ppm 4 Other voices from Change the QT DQT tone and make sure Maximum Frequency deviation 5kHz W 3 5kHz M 2 2 kHz N Kdr7 Un P CAEL Receiver Sensitivity Narrow Band lt 0 28uV TN Transmitting Receiving RUM at Channel Wide Band 0 25uV Frequency Frequency Spacing Adjacent Channel Selectivity 260dB N 70dB W 9 Intermodulation Reject Ratio 265dB 10 Maximum AF Output Power 21000mW 11 Battery Standard DC 7 4V 13 Dimension WX HX D 54 5mm X 113 mmx 35mm 14 34 9 Weight 355g With battery and antenna 15 nn O E E ee 16 2 Optional Functions Bl SETTINGS set by the dealer Time out Time TOT 15 600s Model Serial No SEN S 1 Channels
8. d or the battery power doesn t become low otherwise it might affect the battery life or performance Remove the battery from the charger after charging When using KB 70A if the radio enters low power warning state please recharge the battery Do not use the radio in low power state which will affect the battery life and performance The built in protection circuit in the battery KB 70B will cut off power when power appears low If you charge it in the charger then the red indicator won t light immediately About 1 5 minutes later the charger indicator will become normal INSTALLING REMOVING THE BATTERY PACK Installing the Battery Pack Match the 2 bulges of the battery pack with the corresponding slots at the rear bottom of the radio Installing the Battery Pack Then firmly press the battery pack downwards to lock it in place until a click is heard Removing the Battery Pack To remove the battery pack push the latch upwards and then pull the battery away from the radio Notice Do not short circuit the battery terminals or dispose exhausted battery In fire Do not disassemble the battery casing INSTALLING THE ANTENNA Screw the antenna into the connector at the top of the radio by holding the bottom of the antenna and turn it clockwise until secure INSTALLING THE OPTIONAL SPEAKER MICROPHONE Insert the Speaker Microphone plug into the jacks of the versatile connector IN
9. eing conducted the radio enters the battery save mode It will exit the battery save mode automatically after receiving signals or being conducted Battery Save Types 1 1 1 2 1 4 and OFF Battery save function can decrease the battery power consumption Low Power Warning Low power warning tone sounds and LED flashes when the battery power goes below the preset value and you need to recharge the battery In very low battery status transmission is prohibited Channel Annunciation The dealer can activate or prohibit this function Two types of Chinese and English annunciation are available When switching to a channel by rotating the channel knob the l CAELI current channel number will sound CTCSS DCS The dealer can set CTCSS DCS on the radio channels to ignore calls on the same channel from irrelevant radios Note Using a CTCSS DCS channel doesn t mean your calls are private If the CTCSS DCS tones of other radios are identical with those on yours they can hear your calls B User Template A user template includes PTT code transmitting encoding decoding Busy Channel Lockout Call 1 2 3 4 RX squelch mode TX conditions and decoding conditions etc Maximum 16 user templates are available on this radio RX Squelch Mode The dealer can set conditions under which the speaker will be activated from the following 4 options 1 CTCSS DCS and Audio Squelch The speaker will be activated only when both CTCSS DCS and
10. eived MDC code is non group change the tone on all radios in your group same as the one set in the system it can decode successfully members are Please set 5 Tone selective Signalling on the After the radio received the correct MDC signaling according to heard on the channel the Receive squelch mode set by the user the squelch will channel be ON Then the radio can receive the call and the orange LED Communicati Make sure the antenna is well connected light flashes 5 on range is e Make sure the antenna is the original one too short e Check if the battery power is in the normal state Ask your local dealer to adjust the squelch level Make sure the PTT button has been pressed 2 MDC encode If the PTT ID of the chosen channel is set as MDC the MDC code ill be t itted when calli comp ey varie Wansmiued Men GANING 6 Unable to Battery power may be insufficient Recharge or transmit replace the battery pack e Transmitting frequency has not been set on the O TROUBLE SHOOTING GUIDE channel or the radio has been remote killed e Battery power may be insufficient Recharge or NO PROBLEM SOLUTION 7 Noise is too replace the battery pack 1 The radio cannot Battery pack may not be installed properly loud 2 CURES communication range be switched on or Remove the battery pack and install it again no display after e Battery power may be insufficient Rech
11. en you will hear voice annunciation of the current channel number Adjust Volume Press the monitor button to listen to the background noise and rotate the Power Volume Switch to adjust volume Select Channels Rotate the channel selector to select channels You will hear voice from the speaker while receiving proper signals If voice annunciation of channel number has been set the radio will annunciate the current channel number lI EU t Make a Call To make a call select the desired channel press and hold the PTT button and speak in normal voice Please keep your mouth 3 8 cm away from the microphone Receive a Call Release the PTT button to receive a call Select the desired channel adjust the volume to a proper level and then you can receive others voice m PROGRAMMABLE BUTTON FUNCTION The dealer can program the side button 1 side button 2 and the top button with the following auxiliary functions Null No Function Channel Annunciation Whisper Talk around CALL 1 2 3 4 Lone Work Emergency Alarm Cancel Emergency Alarm Man down Alarm Scan Temporarily Delete Noise Channel Call Forward P CAELI High Low Power Switch Squelch Level adjust Check Monitor Momentary Call Cancel Monitor Call Cancel Squelch off Momentary Call Cancel Squelch off Call Cancel Key Lock Compander Scrambler Battery Power Check Rental Time Check GPS GPS Position Annunciation
12. hazards common to the operation of any radios Warning Turn off your radio before entering any area with a potentially explosive atmosphere where the air contains gas dust and smog etc such as while taking on fuel or while parking at a gasoline service station Precautions in Use Please comply with the following attentions to avoid fire bodily injury and damage to the radio The radio is recommended to transmit for 1 minute and n CAELI receive for 4 minutes Long time transmitting or continuous working in high power mode will make the rear side of the radio generate heat Please don t disassemble or assemble the radio under any circumstances Please don t expose the radio to direct sunlight for a long time don t place the radio near any heating devices either Please don t put the radio in extremely dusty moist or dabbling places don t place it on any unstable surfaces either If the radio emits smoke or strange odors turn it off and remove the battery from the radio and promptly contact your local authorized Kirisun dealer V071010 CONTENTS E UNPACKING AND CHECKING THE EQUIPMENT eene 1 Supplied Accessories eec aed ea Eae nee paene spec nd 1 PREPARATION unummooooto cooemoooo o nmmummummooooooneo Charging the Battery Installing Removing the Battery Pack Installing the Ahternfia icio aaeeea pace azine ae 4 Installing the Optional Speaker Micro
13. if no data is transferred the host radio flashes red indicator 0 25s On 0 25s Off and the sub radio restart B RADIO SETTING TOT Time out Timer 1 TOT Time out Timer A Time out timer is to prevent any caller from occupying one certain channel and radio transmitting overlong b You can program the time out timer i e the time the radio can transmit continuously If the radio has been transmitting continuously longer than the preset time the radio will stop transmitting and warning tone sounds and please release the PTT button 2 TOT Re key a TOT re key specifies the time when transmission is prohibited after the time out timer is activated b During the time of transmitting prohibition if you press the PTT button warning tone sounds and transmitting is prohibited 3 TOT Pre alert Kdr7 Urn a Before the time out timer stops transmitting the radio sounds pre alert tone b After the alarm tone if the transmitting time is longer than the preset time limit the time out timer will be activated 4 TOT Reset a TOT Reset is the delay time between releasing the PTT button and resetting the time out timer b If the time of releasing the PTT button is shorter than the TOT Reset the countdown of transmitting prohibition will continue Battery Save The dealer can program the battery save type If the battery save function has been set 10 seconds after no signals being received or no operations b
14. ion Optional The radio can annunciate the ID number through the microphone when the programmed key GPS ID Annunciation is pressed GPS GPS Time Annunciation Optional The radio can annunciate the current time when the programmed key GPS Time Annunciation is pressed The time zone can be set by the dealer if the radio cannot discover the position then it will annunciate un positioned BIVOX Voice Operated Transmission VOX allows hands free transmission on the radio when using the appropriate earphone headset Two types of VOX are available built in and external If VOX has been set when speaking voice reach the preset volume VOX will activate the radio to transmit automatically Wired Cloning Mode To enter the clone mode wired cloning function should be set on both host and sub radio Wired cloning procedures are as follows 1 Press and hold the Side Button 1 and 2 on the host radio while turning on the radio about 2 seconds later orange indicator flashes n CAEL twice and the radio enters cloning mode 2 Press once the PTT button on the host radio and then the sub radio to receive data will enter Wired Cloning Mode 3 In the cloning mode the host radio lights red indicator and the sub radio lights green indicator Note During the course of cloning if the radio models or software versions doesn t match the host radio flashes red indicator 0 25s On 0 25s Off and the sub radio restart
15. ion Annunciation GPS ID GPS ID Annunciation GPS GPS Time Annunciation Side Button 2 Null Channel Annunciation Whisper Talk around CALL 1 2 3 4 Lone Work Scan Temporarily Delete Noise Channel Transporth Squelch Level Check Monitor Momentary Call Cancel GPS GPS Position Annunciation GPS ID GPS ID Annunciation GPS GPS Time Annunciation Bl Optional Functions e Man Down CAELI Monitor Call Cancel Squelch Momentary Call Cancel Squelch Call Cancel Key Lock Compander Scrambler Battery Power Check Rental Time Check GPS GPS Position Annunciation GPS ID GPS ID Annunciation GPS GPS Time Annunciation The radio will detect angular orientation and lack of user s motion while the Man Down function is enabled When the radio is in non vertical position i e at a factory preset angle e g 45 for the Man Down Emergency Delay Time set by the dealer it will send a pre alert tone If the pre alert timer reaches the preset time by dealer the radio will start emergency process If the radio is put vertical before starting the emergency the Man Down Emergency Delay Time will be reset to the initial Adr7 Un GPS Optional GPS function enables the radio send its GPS information such as Longitude
16. phone seseeeee 4 Installing Removing the Belt Clip sssssee 4 RADIO OVERVIEW 0 uec eid uote EEA 5 BASIC OPERATIONS 5 ettet o ied heel pue tec aag PROGRAMMABLE BUTTON FUNCTION VOX Voice Operated Transmission WIRED CLONING MODBE rere otio derer UE RADIO SETTING tir reete pene eer E MEE EE TOT Time out Timer Battery Save Low JPower Wathlng eria iine tin Sere Rt eL i UD ia Channel AMON CATON uses are tcirii ee 5 Tone Signalling 2 Tone signalling MDE sigrallitig zeros te eri ioe eie tone TER Ere rd e RERO TER obe ara TROUBLE SHOOTING ct ctteian tenete e encor ite asa RO ean dene MAJOR SPECIFICATIONS os i 2e tto rio tpe tine pado bn HE Dm BET ot Bir p tun SETTINGS MU m OPTIONAL FUNGCTIONS cotone ruere A lll UNPACKING AND CHECKING EQUIPMENT Carefully unpack the radio We recommend that you identify the items listed in the following table before discarding the packing material If any damage has occurred during shipment please contact the dealer immediately SUPPLIED ACCESSORIES Li Polymer battery ITEM QUANTITY Antenna 1 Switching Power Supply Belt clip 1 Charger 1 Hand strap 1 1 1 Instruction manual Switching Antenna Power Supply Belt clip TD Charger Hand Strap Battery E PREPARATION CHARGING THE BATTERY PACK Plug the power adapter into the proper AC wall outlet and insert
17. t selective call P CAEL Squelch off Momentary Call Cancel Press the button set as Squelch off Momentary to open the squelch release it to exit When in selective call state press this key to exit selective call Squelch Call Cancel Press the button set as Squelch off to open the squelch press it again to exit When in selective call state press this key to exit selective call Key Lock Press the button set as Key Lock to lock or unlock the keys Compander Press the button set as Compander to switch between compander and Normal mode Scrambler Press the button setas Scrambler to select scrambler function to protect communication privacy Battery Power Check Press the button set as Battery Power Check to hear the current power level One two three or four sound to indicate different power level separately One means the power is insufficient Rental Time Check Press the button set as Rental Time Check and you will hear one two three or four sound to indicate the rest rental time One means the rental time is insufficient EAL GPS GPS Position Annunciation Optional The radio can annunciate the information of the current position such as longitude and latitude through the microphone when the programmed key GPS Position Annunciation is pressed If the radio cannot locate its position then it will annunciate un positioned GPS ID GPS ID Annunciat
18. the cable of the power adapter into the adapter socket on the charger Green LED lights after it enters normal work Insert the battery or the radio to be charged into the charger slot Turn off the radio before insert it into the charger Make sure the battery is in good contact with the charger terminals When the red indicator lights the charger begins to charge the battery After charging for about 5 hours the red indicator turns dim and the green indicator lights indicating the battery has been fully charged Leave the battery in that sate of green indicator for 1 2 hours before you remove it from the charger to achieve the best performance of the battery Then you can disconnect the power adapter from the AC outlet Yellow LED lights when charging temperature or circuit is abnormal and the charger enters protection state Please stop charging in such situation Remove the battery from the charger and cut off charger power Notice The battery is not fully charged in the factory and please charge the new battery when you use the radio for the first time The radio is supplied with a KB 70A Ni MH KB 70B Lithium battery manufactured by KIRISUN Kdr7 Ur When you charge the battery for the first time after purchasing or long storage over 2 months you should repeat charging it several times to achieve the normal battery capacity Do not recharge the battery if it has been fully charge
19. the selective Signallings match 2 Audio Squelch The speaker will be activated when the selective Signallings match 3 CTCSS DCS Squelch The speaker will be activated when CTCSS DCS match 4 Carrier Squelch The speaker will be activated when carrier wave presents DTMF n CAEL The dealer can set DTMF Signalling into encoding sequence If DTMF is set in the encoding template press the corresponding programmable button Call 1 Call 2 Call 3 or Call 4 o transmit the coding 5 Tone Signalling The dealer can activate or inactivate this function by programming 5 Tone has 9 encoding formats CCIR1 CCIR2 ZVEI1 ZVEI2 SVEI3 EEA EIA USER DEFINED 1 and USER DEFINED 2 The last tow formats are user defined 1 5 Tone Decoding The decoding template is 5 tone decoding Received tone telegram matches the decoding template decoding succeeds When receiving proper 5 tone Signalling squelch will be activated according to the RX Squelch Mode defined by the user You can receive the call and LED flashes orange After the radio decoding succeeds the radio will work according to the decoding call response set by the dealer 2 5 Tone Encoding Encoding template consists of at least one and at most three encoding sequences and each decoding sequence can be set with 5 Tone and DTMF If it is set with 5 Tone you need to program its content If the PTT ID on the channel you select has been set with 5
20. this channel temporarily from the scanning list Note The priority channel cannot be deleted And when the number of scanning channels is less than 2 you cannot delete any n TAEL channel either After exiting scanning mode and entering it again the temporarily deleted channel will be added in the scanning list again Call Forward Press this key to enter mode High Low Power Switch Press the key set as High Low Power Switch to switch between high and low power Squelch Level Adjust Check Press and hold the key setas Squelch Level Check to hear broadcast of the squelch level of the current channel Press the key set as Programmable Squelch to change squelch level Press once to increase one grade cycle of 9 0 when in level 0 a beep sounds if the channel has not been set with Signalling squelch keeps long active and store the change 9 Monitor Momentary Call Cancel Press the side button set as Monitor Momentary to turn off CTCSS DCS and 5 Tone and to hear the signals that cannot be heard when in work mode Release the Monitor key to return to work mode When in selective call state press this key to exit selective call Monitor Call Cancel Press the side button set as Monitor to turn off CTCSS DCS and 5 Tone and to hear the signals that cannot be heard when in work mode Press again the Monitor key to return to work mode When in selective call state press this key to exi
21. which signals are detected until the signals disappear If a delay time has been set between the interval of signal disappearing and scanning restarting the radio will keep staying on that channel if it receives any signals during the delay time P CAEL B The working channel of the radio will revert to the following channels automatically when you press PTT button during scanning The dealer can select one among the following six options 1 Start channel When pressing PTT button the radio will transmit from the channel described in the Start 2 Selected channel When pressing PTT button the radio will transmit from the channel selected 3 Last called When pressing PTT button the radio will transmit from the last channel that received a call 4 Last used When pressing PTT button during the scanning the radio will transmit from the last channel you used to talk C Priority Scan During scanning if the priority channel has been set on the radio when the priority channel receives signals the radio will automatically switch to the priority channel even the normal channel is receiving signals at that time And the radio will stay on the priority channel till the signals disappear The dealer can set the delay time between signal disappearing and continuing scanning 9 Temporarily Delete Noise Channel When scanning pauses on a channel press and hold the button programmed as Temporarily Delete Noise Channel to delete
Download Pdf Manuals
Related Search