User Manual - Offshore Systems
Contents
1. 6 of 12 Environmental Parameter Value 60954 Classification Protected Degree of Protection 40 Operating Temperature 25 C to 50 C Storage Temperature 40 C to 70 C Relative Humidity 93 RH 40 per 1 60945 8 2 Vibration 2 13 2Hz e 1mm 13 2 100Hz 7m s2 per IEC 60945 8 7 Offshore Systems warrants this product to be free from defects in materials workmanship for one year from the date of original purchase If within the applicable period any such products shall be proved to Offshore Systems satisfaction to fail to meet the above limited warranty such products shall be repaired or replaced at Offshore Systems option Purchaser s exclusive remedy and Offshore Systems sole obligation hereunder provided product is returned pursuant to the return requirements below shall be limited to the repair or replacement at Offshore Systems option of any product not meeting the above limited warranty and which is returned to Offshore Systems or if Offshore Systems is unable to deliver a replacement that is free from defects in materials or workmanship Purchaser s payment for such product will be refunded Offshore Systems assumes no liability whatsoever for expenses of removing any defective product or part or for installing the repaired product or part or a replacement therefore or for any loss or damage to equipment in connection with wh2. stripped for 8mm and then the cage clamp opened with a small screwdriver in the slot above the wire connection Then simply insert the wire into it s connection slot and release the cage clamp by removing the small screw driver This will produce a secure gas tight connection on wire sizes from 0 08 1 5 mm 2 5 J1939 Connections The terminal connections are numbered as follows Terminal 1 CAN H HIGH level J1939 CAN bus line Terminal 2 Ground Terminal 3 CAN L LOW level J1939 CAN bus line These are marked on the unit case CONFIGURATION The following two items can be configured directly on the 3185 using the two small rotary switches There are no other menu setups to worry about 3 1 J1939 Source The J1939 Source dial is now redundant to the design and does not require setting to a specific setting Dial can be set to 0 as a precaution 3 2 NMEA2000 Device Instance Each 3185 J1939 to 2000 Adaptor connected to the 2000 network needs to have a unique Device Instance Address The Device Instance of each unit is set by turning the small rotary switch with a small screw driver Valid Device Instances range from 0 through to F J1939 Data Translated to 2000 Type PGN No Parameters J1939 PGNs PGN61443 Engine Percent Load PGN61444 Engine Speed Percent Torque PGN65270 Engine Turbocharger Boost Pressure PGN65262 Engine Oil Temperature Engine Cool
3. J1939 to NMEA2000 Adaptor Part Numbers 3185 USER MANUAL Revision 1 01 1 Introduction 1 1 Firmware Revision 1 2 Product Features i kikan kwa n W kn kan 2 2 Installation 2 1 Unpacking the box 2 2 Mounting the unit 2 3 Connecting the 2000 2 4 Connecting the J1939 cable to the WAGO socket 2 5 J1939 Connections 3 Configuration 3 1 2000 Device Instance 4 Warranty 5 Technical Support INTRODUCTION The Offshore System s NMEA2000 3185 J1939 to 2000 Adaptor is designed to convert Engine Transmission and Generator messages on the J1939 network onto the NMEA2000 network This unit is designed to operate in a protected marine environment such as an engine room It is very important that it is installed and set up correctly according to this manual Please read and follow the installation and setup instructions carefully to achieve the best results 1 1 Firmware Revision The information in this manual corresponds to firmware revision 1 1 3 1 2 Product Features The 3185 J1939 to 2000 Adaptor has the following features e Connection to J1939 network using a 3 pole Wago cage clamp connector Green LED confirming valid J1939 message reception NMEA2000 micro C interface plug User Settable a 2000 Device Instance using rotary switch Blue LED confirming NMEA2000 transmission NMEA200009 Interface optically isolated from J1939 Power drawn o
4. ant Temperature PGN65271 Alternator Potential Voltage PGN65266 Engine Fuel Rate PGN65253 Engine Total Hours Operation PGN65263 Engine Coolant Pressure Engine Fuel Delivery Pressure Engine Oil Pressure PGN65214 Engine Rated Speed PGN65260 Vehicle Identification Number PGN65242 Software Identification PGN61445 Transmission Current Gear PGN65272 Transmission Oil Pressure Transmission Oil Temperature PGN65030 Generator Average Line to Line Voltage Generator Average Line to Neutral Voltage Generator Average Frequency Generator Average Current NMEA2000 Parameter Group Numbers PGNs Type PGN No Parameters Periodic Data PGNs PGN127488 Engine Parameters PGN127489 Engine Parameters PGN127498 Engine Parameters PGN127493 Transmission Parameters PGN65030 Generator Average Basic AC Quantities Protocol PGN126464 Tx Rx PGN List PGN126996 Product Information 59392 ISO Acknowledge 59904 ISO Request PGN060928 ISO Address Claim PGN126208 Command Request Group Electrical and Mechanical Parameter Value Comment Operating Voltage 9 to 16 Volts DC Voltage Power Consumption 120 Average Operating Load Equivalence Number 3 LEN Reverse Battery Protection Yes Indefinately Load Dump Protection Yes SAE J1113 Size mm 96 x 84 x 35 Weight gr 120
5. g null and void Offshore Systems reserves the right to modify or replace at its sole discretion without prior notification the warranty listed above 5 TECHNICAL SUPPORT If you require technical support for any Offshore Systems products you can reach us using any of the following ways e Tel 44 0 1425 610022 e Fax 44 0 1425 614794 e Email support osukl com e Web www osukl com e Post Offshore Systems UK Ltd Unit 10 11 Milton Business Centre Wick Drive New Milton Hampshire BH25 6RH Offshore Systems UK Ltd Unit 10 11 Milton Business Centre Wick Drive New Milton Hampshire BH25 6RH United Kingdom Tel 44 0 1425 610022 Fax 44 0 1425 614794 Email mail osukl com Web www osukl com Copyright 2015 Offshore Systems UK Ltd All rights reserved Our policy is one of continuous product improvement so product specifications are subject to change without notice Offshore Systems products are designed to be accurate and reliable However they should be used only as aids to vessel monitoring and not as a replacement for traditional navigation and vessel monitoring techniques 2000 is a registered trademark of the National Marine Electronics Association N EBA ELI jI 411 d SWALSAS ONY 13553A sO00CVIWN dVW LONGOYd SWALSAS JYOHSAAO
6. ich Offshore Systems products or parts shall be used The foregoing warranties shall not apply with respect to products subjected to negligence misuse misapplication accident damages by circumstances beyond Offshore Systems control to improper installation operation maintenance or storage or to other than normal use or service THE FOREGOING WARRANTIES ARE EXPRESSLY IN LIEU OF AND EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE Statements made by any person including representatives of Offshore Systems which are inconsistent or in conflict with the terms of this Limited Warranty shall not be binding upon Offshore Systems unless reduced to writing and approved by an officer of Offshore Systems IN NO CASE WILL OFFSHORE SYSTEMS BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES DAMAGES FOR LOSS OF USE LOSS OF ANTICIPATED PROFITS OR SAVINGS OR ANY OTHER LOSS INCURRED BECAUSE OF INTERRUPTION OF SERVICE INNO EVENT SHALL OFFSHORE SYSTEMS AGGREGATE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT S INVOLVED OFFSHORE SYSTEMS SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHETHER ARISING OUT OF BREACH OF CONTRACT OR WARRANTY TORT INCLUDING NEGLIGENCE OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY OFFSHORE SYSTEMS OR ANY UNDERTAKINGS ACTS OR OMISSIONS RELATING THERETO Offshore Sy
7. nly from NMEA2000 interface Panel or DIN rail mounting option NOTE FOR SAFETY REASONS THIS UNIT DOES NOT HAVE THE CAPABILITY OF TRANSMITTING ANY MESSAGES ONTO THE J1939 NETWORK INSTALLATION 2 1 Unpacking the box You should find the following items in the 3185 shipping box 1 x 3185 J1939 to 2000 Adaptor 1 x Din Rail mounting Kit with 2 rail mounts and 4 countersunk M3 screws for rails 1 x 3185 User Manual This document 2 2 Mounting the unit The unit can either be mounted to a flat surface using 4 mounting screws The unit dimensions and mounting hole locations are shown on the following drawing Or the unit can be Din Rails mounted by attaching the Din Rail mounts to the case using the supplied M3 CSK screws and then clipping the unit to the Din Rail 2 3 Connecting the NMEA2000090 Cable The unit is connected to the 2000 network by the 5 way micro C socket on the front Carefully attach the network drop cable to this plug and hand tighten until it it is fully seated Take care to match the orientation of the pip inside the socket to the recess inside the drop cable plug The other end of the drop cable should be connected to a suitable Tee connector on the 2000 network backbone cable 2 4 Connecting the J1939 cable to the WAGO socket The cables from the power source to the external sockets are connected using the WAGO Cage Clamp terminal block The wire should be
8. stems does not warrant that the functions contained in any software programs or products will meet purchaser s requirements or that the operation of the software programs or products will be uninterrupted or error free Purchaser assumes responsibility for the selection of the software programs or products to achieve the intended results and for the installation use and results obtained from said programs or products No specifications samples descriptions or illustrations provided by Offshore Systems to Purchaser whether directly in trade literature brochures or other documentation shall be construed as warranties of any kind and any failure to conform to such specifications samples descriptions or illustrations shall not constitute any breach of Offshore Systems limited warranty WARRANTY RETURN PROCEDURE To apply for warranty claims contact Offshore Systems or one of its dealers to describe the problem and determine the appropriate course of action If a return is necessary place the product in its original packaging together with proof of purchase and send to an Authorized Offshore Systems Service Location You are responsible for all shipping and insurance charges Offshore Systems will return the replaced or repaired product with all shipping and handling prepaid except for requests requiring expedited shipping i e overnight shipments Failure to follow this warranty return procedure could result in the product s warranty becomin
Download Pdf Manuals
Related Search