Simpson S660-1-1-2-1-0 datasheet: pdf
Contents
1. Easily Programmed from the Front Panel Software Functions Include Password Set Point Programming Display Scaling Decimal Point Selection Screw Terminal Connectors for Easy Installation Rugged High Impact Plastic Case Fits Standard 1 8 DIN Cutout 3 24 82mm for Restricted Space Behind Panel Remote Reset Capability Input Variety Quadrature Switch TTL CMOS NAMUR PNP NPN Optional 5 Amp Relay Outputs The S660 is a versatile totalizing counter that can be adapted to a wide variety of counting measuring and controlling applications The control inputs offer several counter operation modes count direction add add add subtract subtract subtract quadrature and reverse quadrature Optional relay outputs enhance the counter from a passive device to an integral control element for your application The S660 is compactly designed and features a stan dard 1 8 DIN case made of PBT ABS alloy Screw ter minals are standard for easy installation and removal of the meter Installation and Panel Cutout 1 77 45mm 3 56 lt _ 90 7mm gt Core Self Totalizer Counter S660 Preset Totalizer Counter CEO 0 The counter is powered from 120 or 240VAC and has a non volatile EEPROM to retain all programming and count information when the power source is removed or interrupted The S660 accepts pulses from Q2. SE 1725 RPM Lo speed 430 RPM 600 An encoder chariot 46012 and 12 measuring wheel with 83A durameter non marking tires 46005 are also required Shear Specifications The pneumatic cutting blade is activated by applying 120VAC 0 5 amp maximum to a con trol valve Mechanical A motor reducer and drive pulley result in 1 of linear travel for every five motor revolutions Application Example Contd CHANNEL A W CHANNEL B G HITE REEN QUADRATURE ENCODER COMMON BLACK QUADRATURE EXCITATION INPUT CARD CARD POSITIVE RED Ordering Information Power Supply Output H None One Relay Two Relays 120VAC 240VAC Basic unit S660 Excitation Safety Symbols The WARNING sign denotes a hazard It calls attention to a procedure practice or the like which if not correctly performed or adhered to could result in personal injury The CAUTION sign denotes a hazard It calls attention to an operating None 12VDC Input procedure practice or the like which if not cor Standard Quadrature 1 2 SE Quadrature Encoder The cube style dual shaft SE Encoder is available with a choice of five different resolutions pulses revolution to handle a broad range of mea suring jobs When the encoder is affixed to a char
3. Disabled at a set point or after output times out See also the At SP2 RSTPOS parameter in the Setpnt Setup category Reset SETUP At SP3 at SP4 Aft OPI Aft OP2 Default Setting Programming Cont d Menu Category Parameter Name Choices Format Description Rst Btn enable Reset Button Enable or disable front panel reset button Reset SETUP di sabl No Power On Reset select whether count reset event will occur at Yes power up End Exit Programming Menu Default Setting Excitation O utput Denotes module position 2 at rear of counter The Excitation Module can supply 12VDC at up to 100mA for external sensors or encoders This excitation is isolated from the counter internal logic supply When using sensors or encoders that do not have a signal return or imply a signal return that is in common with the supply voltage a common attachment that ties the excitation supply to the logic input common may be required 12 VDC 100 mA max Single and Dual Relay Modules E A Denotes module N O Qi position 5 at COM amps at 250VAC A Form C configuration allows use of normally open ain NO and normally closed NC circuit action rear of counter i O The Single and Dual Relay modules can activate circuit loads of up to 5 N C Wa SINGLE RELAY RELAYS con Only the output 1 channel is implemented in the sin
4. e J Position 4atrear allows the S660 to be operated from stan B oteountar dard 50 60 Hz line power The power mod Gee Powersin ule will be configured as 120 or 240VAC per v qo VAC e340 markings on the back panel Ensure the vac F vac power input rating of the supply matches your line connection voltage The power supply module has pro Qreser Remote Reset Visions for a hard wire Count Reset This Active low0 2v Control can be a switch relay contact or Snn ini Deon el primary solid state device The reset circuit is inde net eto The Input module also provides for a User POWER in y ACP Modul pendent of the power circuit input signal On the S660 this input serves Ower MOUS as a count enable disable control Input Module The DIP switch SW1 is used to set up the counter to Connecting User to Common will disable conform to the electrical characteristics of the sensor or signal being counting detected Switch positions 1 3 configure channel B while switches 4 6 configure channel A These switches select bias threshold voltages low pass filter enable disable and sensor type sink or source Refer to the sensor s documentation for related information SS G OSS Standard Input Module Programming Menu Category Parameter Name Choices Format Description Pass 000 Password Entry and Verification Access lt gt denied Password Fail Appears if incorrect
5. gle relay module On Single Relay Module Dual Relay Module Application Example A Simpson Encoder and Counter are to be used to measure and cut Process Minimum and maximum piece length will be 12 raw material to length A dual speed motor is used to allow selection of inches and 6000 inches 500 feet respectively high speed low speed and stop A pneumatic shear allows the material Material is a light colored textile so skidding by to be cut measuring device is to be avoided Material is initially to be fed at high speed In the final six inches low Display Desired display and entry of lengths is in inches speed will be used When the desired length is reached the motor will with two decimal places 1 100 inch resolution be temporarily stopped and the shear activated for two seconds The i e The customer would like to enter 0 25 inch feed and cut cycle then resumes for a new piece increments Machine Specifications Product Ordering Information Motor and Control Motor runs in low speed when 120VAC applied In the application example a Simpson S660 Preset Totalizing Counter to Run Lo terminal Hi Speed selected with with a120VAC power supply Quadrature Input Dual Relay Output and 120VAC to Run Hi Terminal Maximum control 12VDC excitation is used catalog no 660 1 2 2 1 0 The encoder current is 3 amps at either terminal Hi speed used is the SE Quadrature Encoder with 600 pulses per revolution
6. ied High Bias VLT 5 0V 10 less than 32 C decreasing linearly to 50 at indication displayed VUT 7 0V 10 40 C Display Range 99 999 to 999 999 Count Rate 20KHz Pulse Max Ambient Temperature 25 C Output Indicators 1 and 2 5KHz Quadrature X4 Max Temp Coefficient per C 100PPM C Maximum Voltage Input Warmup Time 15 minutes POWER REQUIREMENTS A B and User 30VDC Max AC Voltages 120 240VAC 10 MECHANICAL Power Consumption 3VA IN PUT Bezel 3 93 x 2 04 x 52 User Input Display Hold Display is frozen 99 8mm x 51 8mm x 13 2mm INPUT RATINGS when the User Input is pulled low Depth 3 24 82mm Current Sinking 10K 5 Resistor pull up to Standard Input VLT lt 0 2VDC guaranteed Panel Cutout 3 62 x 1 77 92mm x 45mm 9 0 16 VDC 10 low VUT 3 0VDC max Case Material PBT ABS Current Sourcing 5 1KQ 5 Resistor pull Quadrature Input VLT 0 9VDC Weight 9o0z 255 19 down to common VUT 3 15VDC max Wiring Diagram Power Module The AC power module Deras mocuie Note The input boards are designed so that of counter selecting sourcing or sinking is based on the comem mpu type of sensor that is being used If a PNP So o pe sinking sensor is being used set the input board for sinking also switches 3 and 6 iib OFF If channel B is not used default set INPUT sca counting tings for switch positions 1 through 3 should BiNrur be selected COMMON HL Denotes modul
7. il parameter Appears only if SP1 Mmodel latch SP2 SP3 SP4 Rst Pos MMode2 Di sabl Output 2 Mode Set the mode of operation for Output 2 Can be ti mmed disabled timed latched or boundary mode Latch bound Ti mmed lt gt At SP3 Output 2 Reminder message indicates which and how the set points Latched lt gt At SP3 are used for comparison Which message is displayed is determined SP3 L0 lt gt SP4 Hi by the Output 2 mode selected OPUT 2 SETUP Del ay2 010 00 Delay 2 Output 2 delay time Appears only if Output 2 mode set to timed Until 2 Reset Until 2 Output 2 latched until parameter SP1 Appears only if MMode2 latch SP2 SP3 SP4 Rst Pos SP1 000010 SP1 SetPoint 1 Low Values 99999 to 999999 Decimal point will appear according to the current DP setting SP2 000020 SP2 SetPoint 1 High Values 99999 to 999999 Decimal point will appear according to the current DP setting SetPnt SETUP P3 000030 SP3 Set Point 2 Low Values 99999 to 999999 Decimal point will appear according to the current DP setting SP4 000040 SP4 SetPoint 2 High Values 99999 to 999999 Decimal point will appear according to the current DP setting RSTPOS 000000 Reset Position Count value is set to this when an Auto or Manual Reset event occurs Values 99999 to 999999 Decimal point will appear according to the current DP position Areset Disabl Auto Reset Mode Selects when an auto reset function is to occur At SP1
8. iot with measuring wheels and wired to one of the S660 series counters cut to length measurement applications are assured an accurate and reliable read ing Pulses Per Revolution 60 100 120 360 600 Catalog Number SE 060 SE 100 SE 120 SE 360 SE 600 rectly adhered to could result in damage to or destruction of part or all of the instrument Chariot The Chariot is used to mount most cube style quadrature encoders and measuring wheels Made of anodized aluminum the chariot includes mounting hardware and selectable pivotal points Wheels tires and flexible shaft couplings are sold separately 12 Circumference Measuring Wheels with Tires These 12 inch wheels are precision machined anodized aluminum with a printed alignment scale Replaceable tires are available in four differ ent durometers for use on a wide range of materials including non marking tires to prevent tearing damaging or marking up delicate materials Tire Durometer 80A black tire longer service life for plastics metals 83A non marking tire for textiles medium textures 92A non marking tire for plastics metals coarse wood 70A non marking tire for soft textiles Catalog No 46004 46005 46006 46007 Revised 5 11 04
9. password entered ChPass 000 Password Change Appears if correct password entered 000 pass word protection disabled 001 099 secures all parameters 100 999 enable SPs ResPos access in display mode Chan A Mode Select count mode of A channel Input Setup Chan B Mode Select count mode of B channel Note If A channel set to Quad orR quad this item is not accessible Pre scale Set prescaling multiplier CountSetup Scale Set Display Value scaling multiplier Values 9 9999 to 99 9999 Default Setting Programming Contd Menu Category Parameter Name Choices Format Description dp 000000 DP Display Value 1 Count Decimal Point location Affects 000000 appearance of RstPos and any associated set point parameters 000000 count SETUP 0000 00 000 000 00 0000 0 00000 mmo de 1 Di sabl Output 1 Mode Set the mode of operation for Output 1 Can be ti mmed disabled timed latched or boundary mode Latch bound Ti mmed lt gt At SP1 Output 1 Bindings Reminder message indicates which and how the Latched lt gt At SP1 set points are used for comparison Which message is displayed is OPUT 1 SETUP SPl Lo lt gt P2 shi determined by the Output 1 Mode selected Del ayl 010 00 Delay 1 Output 1 delay time Appears only if Output 1 mode set to timed Untill Reset Until 1 Output 1 latched unt
10. uadrature CMOS or TTL circuits and PNP or NPN devices The optional 12VDC 100 mA excitation output module can provide power for external sensors Other programmable software features include program mable decimal point and a password lockout feature By using the password feature the meter s program ming functions and set points are protected from acci dental reprogramming Engineering Label Mounting Requirements The S660 series 1 8 DIN counters require a panel cutout of 1 77 45mm high by 3 62 92mm wide To install the counter into a panel cutout remove the clips from the side of the meter Slide the meter through your panel cutout then slide the mounting clips back on the meter Press evenly to ensure a proper fit Engineering Label Placement If replacement of the engineering unit label is required place the tip of a ball point pen into the small hole at the base of the engineering label in the bezel Slide the label up until it pops out Grasp and remove Slide the new label half the distance in then use the ball point pen to slide it down into place Specifications DISPLAY Minimum Pulse Width 5ys ENVIRONMENTAL Type 6 digit 7 segment red LED Low Pass Filter lt 200Hz Operating Temp 0 C to 40 C Height 0 56 14 2mm Low Bias VLT 1 6V 10 Storage Temp 10 C to 60 C Decimal Point User programmable VUT 3 6V 10 Relative Humidity 0 80 for temperatures Count Direction indication impl
Download Pdf Manuals
Related Search