6 IN 1 JUMP STARTER
Contents
1. Safety Switch which located at the back of the unit Lack of power output Power center voltage below 12 volt 1 Recharge the Power Center 6 Start vehicle If vehicle does not start wait 3 minutes before trying again failure to wait may damage immediately Jumpstart p A a lessie corrent diain Reduce load to maxim nr 400 watts 7 After vehicle starts disconnect the black negative clamp first than the red positive clamp by appliance being operated USB POWER SOCKET Inverter not completely warmed up 3 Turn OFF the device and eure USB Power Socket located at the back underneath the fuse it can power charge devices that require 5VDC up Disconnect device Turn the inverter to 2 1A through the use of a user supplied cord ON and leave running for a minimum of 2 minutes Turn OFF inverter SPECIFICATIONS quickly plug in device to inverter 1 Built in Battery 12V 18Ah Sealed Lead Acid Battery making sure device is OFF prior to 2 Work Light 5 x LEDs connection Turn ON the inverter and 3 USB Power Port 5V 2 1A the device 4 Compressor 99 PSI 6 9 Bar Preset Gauge Inverter fuse blown Replace a new 40 AMP rated fuse To 5 Inverter 400 Watt Peak 800 Watt 0 3 sec replace fuse REMOVE fuse with a 6 12V Power Port 12 volt 11A max 7 Charging Time 34 36 hours by AC charger needle nose pliers and replace with a new 40 AMP fuse 12 14 hours by DC charger LED light OFF Inadequate power or excessive Check power center and2. is in the UP position Switch the safety switch ON which is located at the back of the unit Caution Please make sure the air hose is not connected to the valve before setting the inflation pressure Preset the pressure reading by pressing the measure unit button to select BAR or PSI and adjust button or to your desired inflating pressure Attach the valve adapter to the valve stem of tires and push the valve adapter lever down to lock into place Turn the compressor switch on front panel to ON position Monitor the pressure gauge while inflating When preset pressure has been reached it will cut off automatically press the compressor to OFF and disconnect the hose Note It may take up to a minute for the auto cut out to activate once preset pressure has been reached USING 12 VOLT DC POWER PORT 1 Remove the protective cover 2 Plug in your 12 volt accessory 3 Turn power port switch to ON 4 At full charge the power center will power B W TV spotlight for 4 hours mini cooler for 3 hours portable vacuum coffee maker for 1 hour Time may vary depending upon current draw of attached accessory USING AC INVERTER Prior to connecting inverter maker sure the inverter switch is in OFF position 1 Prior to plugging in device make sure the device is OFF and ensure the current drawn of this device is max 400 watt Connect the device electrical plug
3. 6 IN 1 JUMP STARTER User Manual Please read this manual thoroughly before operating this product please keep this for future reference IMPORTANT PRIOR TO USE READ AND UNDERSTAND ALL WARNINGS CAUTIONS AND INSTRUCTIONS INCLUDED IN THIS INSTRUCTION MANUAL AND THOSE PUBLISHED BY YOUR VEHICLE BATTERY MANUFACTURER AND MANUFAC TURER OF ANY DEVICE INTENDED TO BE USED WITH THIS UNIT RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT SAFEGUARDS e To protect against electrical hazards do not immerse charger adapters or unit in water or other liquid Close supervision is necessary when used near children Do not use unit for applications other than its intended use e Recharge battery after every use e Avoid touching eyes when working with batteries e f battery acid comes in contact with skin or eyes flash with water immediately and get medical attention e Remove metal jewelry or objects from your body when using the unit e Never allow red and black clamps to touch each other or to touch the same metal object e Always connect the red clamp to the positive battery terminal first Do not connect black clamp to the negative battery terminal connect it to a non moving metal part on your vehicle e Jumpstart vehicles in a well ventilated area only e Monitor the pressure gauge during use Be careful not to over inflate objects WORK LIGHT e Simply turn the work light switch on front panel to ON pos
4. into the inverter receptacle Press the inverter to ON position If the inverter is working properly a green LED indicator will illuminate 4 Now turn on the device If the green indicator remains on then the system is operating properly If the inverter green LED light turns off turn off the device then turn off the inverter immediately See the trouble shooting guide The inverter may have been over loaded or the input voltage may be too low CAUTION Some rechargeable devices are equipped with a separate charger which can be connected into this inverter AC receptacle However certain rechargeable devices are manufactured with built in chargers see device owner s A cw Pp ONAN WN ow N manual This category of devices may cause internal damage to inverters and should not be used with this JUMPSTARTING inverter The temperature of the device must be monitored for the first 15 minutes of operation Abnormally 1 Turn the ignition OFF Turn off all accessories such as lights radio air conditioner etc elevated temperature of the device is an indication that they should not be used with this inverter 2 Make sure all switches on the Jumpstart System are turned OFF 3 Securely connect the Red clamp to your vehicle battery s positive battery terminal TROUBLESHOOTING GUIDE 4 Do not connect to the negative terminal Connect the black clamp to a non moving metal part of the vehicle 5 Turn ON the
5. ition e The 5 x LEDs will illuminate Turn OFF while not in use BATTERY STATUS e Press and hold the Battery Level Button e The Digital Voltage Meter will show the battery remaining percentage Over 90 Ready to use e 85 or below Charge necessary e 80 Charge immediately CHARGING YOUR JUMPSTART SYSTEM AC Charging At Home Completely charge your Jumpstart before using for the first time 2 Before recharging from an AC outlet be sure the source is right i e 110 volts or 230 volts 3 Use only the chargers provided with unit 4 5 Keep the power on off Safety Switch in OFF position while charging Plug the AC charging cord into any standard wall outlet and the other end into the AC DC charging input socket Full charge takes approximately 34 hours Do not exceed recommended charging time 48 hours N oO e Charging In Your Vehicle 1 Keep the power on off Safety Switch in OFF position while charging 2 Plug the DC charging cord into any 12 volt cigarette lighter outlet and the other end into the AC DC charging input socket 3 Full charge takes approximately 12 hours 4 Do not exceed recommended charging time initial charge 24 hours USING AIR COMPRESSOR CAUTION Check item to be inflated for manufacturers maximum recommended inflation pressure Avoid over inflation 1 Open the compartment door at the back of the power station and pull out air hose Make sure the nozzle lever
6. recharge is voltage drop voltage drops below 12 volt Inverter is overloaded Replace load to maximum of 400 watis Television Power Tool High surge wattage requirement Toggle the On Off switch in quick will not start to start up succession a total of 5 times in order to generate the necessary power to start the device If the device does not turn on or start up in 5 cycles of ON OFF trials This inverter will not work with the device Television Interference Picture breaking up snow Place the inverter power center as far as possible from TV the antenna and the coaxial cable 2 TV station may be out or range Static Noise interference 1 Sound system has weak alternating 1 Do not use inverter with low quality in audio system current shielding audio AC filtering system Replace audio system with high quality noise filtering
Download Pdf Manuals
Related Search