Toyota Lexus Scion User Manual
Contents
1. 9600 10247 radio buttons within the options dialog one can set the order in which these two baud rate values will be used If 10472 9600 is selected then first the commander will try to connect to the device over K Line using baud rate 10472 and if it doesn t succeed it will switch to 9600 and try again with it If 9600 10472 is selected then first the commander will try to connect to the device using baud rate 9600 and if it doesn t succeed it will switch to 10472 and try again with it 3 1 4 Logging group By checking the Enable CAN Log and Enable K Line Log check boxes on the Logging group it is possible to log the whole CAN K Line communication when a problem with a specific control unit occurs Please note that they are enabled by default The log files are binary files which are placed in the Toyota Log sub folder of the C Program Files ABRITES software for ID 12001F unless you change it during the installation process With each start of the ABRITES Commander for TOYOTA LEXUS SCION one file is created and it contains the date time when it is created in its filename Page 12 of 36 NOTE Please pay attention that if the space on your Hard disk is not much you can disable communication logging and or remove old Log files For you convenience there is an automation process which will erase older than one month files to Save disk space Page 13 of 36 3 2 Scanning units2. Clear all DTCs button 3 2 0 Personalize By clicking button Personalize you have groups with personal car settings Every one group contains a bunch of settings for management The set of personal settings is different for different cars so not every setting is available in every car In order to you this function make sure that Ignition is ON Page 15 of 36 Personal Settings Wireless Door Lock O1 Security 02 Wiper 03 Seat Belt Warning 04 Key Warning 05 Till Telesco 06 Air Conditioner 07 Display Open 08 Retractable Hardtop 09 Compass Calibration 10 RSD PBD Operation 11 Seat 12 Door Lock 13 Power Window 14 Illiuminated Entry 13 Light Control 16 Slide Roof 17 Sensor 16 Unit Conversion Smart Eer and Berereee For example To change Seat belt warning you have to Double click 03 Seat_Belt_Warning or select 03 Seat_Belt_Warning and click Open button Then select desired functionality and click Save button You will see the updated value of the selection And corresponding information with status of the operation Page 16 of 36 Seat Belt Warning Driver and Pas senger ON Q Only Driver ON Q Only Passenger ON O Driver and Passenger OFF Data read To change item s value vou have to select it and press Save button 3 3 Standard diagnostic requests When double clicking on the desired device in the main ABRITES Comma
3. 120 Toyota Prado Toyota 4 Runner Page 30 of 36 PROCS en 2 OP Tar utong Toyota Camry 2004 Toyota Corolla 2007 Toyota Hilux Toyota Prius Page 31 of 36 e Me aute Lions Toyota Avalon Lexus LX470 Lexus LX570 Lexus RX300 Page 32 of 36 ABR ES autorit Utions Lexus RX330 Lexus RX350 Lexus RX400 Lexus RX400h Page 33 of 36 Lexus SC430 Lexus GS300 Lexus GS430 Lexus GS450 Page 34 of 36 ES utions Lexus ES350 Lexus IS220 Lexus IS250 Lexus IS350 Page 35 of 36 QUOI Lexus LS430 Lexus LS460 Scion Page 36 of 36
4. 2 INSTALLATION Your set consists of one USB to OBDII interface and one USB dongle 2 1 Installing the USB dongle drivers The dongle is configured to work in HID mode and doesn t require a driver After you put the dongle in the USB port of the PC it should be recognized as a HID compliant device when you open the Device Manager m Device Manager Fig Adon Sew Heh es Poni wis E a Disk dives H Pre apen al Imaging devices a gt kKepboards f Mice and other pointing devices Fe ll Monitors RY Network adapters G48 Portable Devices fl Ports COM amp LPT Processors 2 2 Installing the USB Interface drivers You will be prompted to install the USB Interface driver automatically at the end of the installation of the ABRITES Commander for TOYOTA LEXUS SCION You can also download and install the driver manually The latest USB driver is available at Page 4 of 36 Windows Vista Vista x64 XP XP x64 2000 Server 2003 Server 2003 x64 www vag commander com download Interface Driver USB CDM 2 02 06 exe Windows 98 ME www vag commander com download Interface Driver USB Interface Driver USB 98 zip Unpack and run the applied executable When the driver is installed a screen that looks like the following this will be displayed es CADOCUME 1 ADMINI 1 LOCALS 1 Temp ckz_GSTO DPInst_Monx 6 exe Jof x 32 bit S detected C SDOCUME 1 ADMNIAI 1 LOCALS iNTemp ec
5. After startup on the main screen of the ABRITES Commander for TOYOTA LEXUS SCION a list of all possible units is displayed The customer is able to connect to the listed devices by double clicking on the desired device or selecting the unit name and pressing Connect button Instead of displaying all possible units you can choose a configuration of devices corresponding to a specific car model from the Chassis group This is done by specifying the vehicle brand e g Toyota which is the default value and then selecting the vehicle model from the Chassis group drop down box This will show all devices which may be present in this car model for Toyota RAV4 in the example below ABRITES Commander for Toyota Lexus Scion 2 4 www ABRITUS 2 com Protocol orcs vin _ f 01 O x 06 Cruise Control 07 Hybrid Control 08 Hybrid Vehicle Battery 09 Hybrid Gateway 10 Mirror Connect 11 Air Condition System 12 AHC 13 Air Suspension System 14 Intuitive P A IPA 15 ECB Gateway 16 ECM gateway Next 17 Gateway a Engine and Transmission 2 Automatic Transaxle 03 ABS 04 Airbag SRS 05 Immobilizer 2 Vehicle Selection i Special Functions l Options Chassis MTOVYOTA OSCION OLEXUS General All units NOTE Please pay attention that manufacturers could change the car equipment along the year So there is no guarantee that you have the right set of units To be sure for the car
6. Step 2 Execute Immo Reset the procedure is approximately 15 18 min long Step 3 Switch the Ignition ON Step 4 Execute Register Key follow the screen instructions Step 5 Test the key functionality before closing the door If you have a remote control in the Key and if it is not working could be Toyota Prius then execute Step 6 and 7 Step 6 Execute Smart System Reset Step 7 Execute Register Smart Remote 3 4 4 Smart System Reset Smart System Reset Smart System Reset provides you a possibility to clear all programmed smart cards from the vehicle WARNING After using this function all smart cards will be erased from the vehicle memory For this reason it is strongly recommended to program at least one smart card after using Smart System Reset For a list of Supported vehicle models on which this special function can be used please see the Appendix 3 4 5 Register Smart Remote Register Smart Remote provides you a possibility to register a new smart unit for the vehicle The driver s door is open Press Register Smart Remote Within 30 sec you should execute following 3 steps Ignition OFF Press simultaneously Lock and Unlock buttons on you remote for 1 second 6 Press Lock key After step 6 you have to hear conformation sound from the car Now you can close the door and try your remote ee SY SS Page 22 of 36 If there is n
7. available diagnostic Abrites software functions User Manual Folder with available help documentation Installation process During startup a splash screen appears Please follow the installation steps to install the software Normally the software will be installed into Destination location C Program Files ABRITES software for ID 12001F Start Menu folder ABRITES software for ID 12001F Page 8 of 36 After successful installation you can run the ABRITES Commander for Toyota The main screen looks like this O x ABRITES Commander for Toyota Lexus Scion 2 4 www ABRITUS 2 com unit name sd Protocol orcs wes S e 01 Engine and Transmission 02 Automatic Transaxle 4 03 ABS Previous 04 Airbag SRS 05 Immobilizer 06 Cruise Control 07 Hybrid Control 08 Hybrid Vehicle Battery gt 09 Hybrid Gateway 10 Mirror Connect 11 Air Condition System 12 AHC 13 Air Suspension System 14 Intuitive P A IPA 15 ECB Gateway 16 ECM gateway Next 17 Gatewa a Vehicle Selection i Special Functions l Options Chassis TOVOTA OSCION OLEXUS P Ceneral All units Scar All Clear all DTC Personalize ATTENTION Make sure you are running the ABRITES Commander for Toyota from the proper folder or if you are using a shortcut to the ABRITES Commander for Toyota please be sure that the Target parameter is set properly usually this is C Program Files ABRI
8. equipment it is recommended to Scan All units in the car 3 2 1 Scan All Pressing the Scan All button will attempt to connect to each device currently displayed in the list Depending on the configuration options you set ATTENTION Only the selected protocols will be used when scanning for available devices As this is an exclusive procedure a progress bar will appear to show you the status of scanning Page 14 of 36 ABRITES Commander for Toyota Lexus Scion 2 4 www ABRITUS 2 com l unit name Cd Protocol orcs o ow O 01 Engine and Transmission CAN ISO TP Not Extracted JTDRB200277363699 02 Automatic Transaxle CAN I50 TP 69 03 ABS CAN ISO TP 69 Sy cians 2 Vehicle Selection 4 Special Functions Options Chassis MTOVYOTA OSCION OLEXUS General All units After the procedure is finished the statistic will be visualized on the main screen lt is possible that not all of the modules report their problems DTC during a common scan In this case Not Extracted label will show you that there is unknown number of DTC for some module By double click on this module you can Read DTC s for it 3 2 2 Clear all DTCs Since clearing of the DTCs for all present in the vehicle devices is one of the main diagnostic operations there is a possibility after scanning of all devices if connection to the device is possible to clear all available DTCs This is function is available by pressing the
9. you have problems as described in the Troubleshooting section you can try to set the port used by the ABRITES Commander for TOYOTA LEXUS SCION manually This can be done as follows Open the Device manager and check as which COM port the USB interface is recognized Uncheck the Automatic check box and set the port in the respective field Page 11 of 36 a Device Manager Ele Acorn Wiew Help E Fi Dis Displayed IE E DYDOCO AOM dives HUR Human Interface Devices H E IDE ATA ATAFI controllers Imaging devices Z Keyboards A Mice and other pointing devices BE Monitors EF Network adapters rH Ports LOM amp LPT a va Communications Port COM ee E E E rer Sound video and game controllers i 4 Storage controllers i 0E System devices re F Universal Seral Bus controllers Example USB interface device recognized as COM11 Hint If you are not sure which is the port used by the interface just unplug and then plug it into the USB slot observing the Ports section in Device Manager The corresponding port will disappear and then appear again 3 1 3 K Line Baud Rate Settings When trying to connect to a device in the vehicle over K Line the Abrites Commander will try to connect to it using one baud rate and if it doesn t succeed it will switch to another baud rate and try again There are two baud rate values currently used 10427 and 9600 Using the 10472 9600 and
10. A ATTE TETERA 22 IAS T T aT a O ana A E E a 22 3 4 6 Add Key applicable for smart systems nnoooonnnnnnnnnnnnnssseennnnsssseeeenennsssseerenssssseereeossssseeresssssseereesssssee 23 i ey D O a E N A AA E E E E emer ere 23 34 5 ECU Engine CONT OL Unit siciccnsdencduvaataxccasinativesieawsevade NENN AT EA EAEEREN EENEN EEE EAEE A EENE NEE 24 3 4 8 1 Poad TI e E a E cnasyisaats ae netoncetuecahaaoarea uccane 25 3 4 8 2 w e T e E E E E E N 25 3 4 8 3 AV AL E ET E N E A AE A OEA E A O E OE A A 25 3 4 8 4 NAAT OVA EEIE EA EE EE AE A IEE E SE IEE E A EE AA A AE 25 TKOUBLESHOOTIN G i E E E sesseeuisovinaessecuvauias 26 APPENDS ceea E E E E A E 29 5 1 SUPPORTED MODELS FOR KEY LEARNING iruretan srie nr aA OAOE E EARTE 29 Page 3 of 36 1 INTRODUCTION ABRITES Commander for TOYOTA LEXUS SCION is a Windows PC based professional diagnostic software for vehicles from the TOYOTA LEXUS SCION group With the help of this software you can perform complete diagnostic operations of all 2000 present vehicles from the TOYOTA LEXUS SCION group which are in most cases unsupported from the producer diagnostic testers The ABRITES Commander for TOYOTA LEXUS SCION provides also complete standard diagnostics read faults erase faults current data actuator tests for TOYOTA LEXUS SCION vehicles Our PC USB diagnostic interface supports K Line and CAN BUS interface Diagnostics is performed via the OBD II connector
11. ABRITES ToyvoTa LEXUS SCION COMMANDER A B RIT ES ABRITES Commander for TOYOTA LEXUS SCION User Manual Version 2 4 issued by Abritus 72 Ltd Page 1 of 36 ABRITES Toyota LEXUS SCION COMMANDER List of Revisions 19 06 2009 Date Chapter 23 11 2009 Add EDC15 Read Write Fix Smart remote reset and Added Personalization functionality Page 2 of 36 1 2 5 ABRITES Toyota LEXUS SCION COMMANDER AB RII ES MINTO ON coc E S 4 INSTALLA TION secsessceresasscccseusvebeesicecuastevnesserasacuescesssteesisesbeovasstsiesueteasseveetacncecevesseseosashexetiseactusstiernestenvaresaisissecuiats 4 2 1 INSTALLING THE US B DONGLE DRIVERS scsisxeesasracdcceese ara sie a ee ee 4 22 INSTALLING THE USB INTERFACE DRIVERS sgssssicnssiessesscaenseaaduncsnseoncesvagiessdesstensessaduanensebomesagiesdesesadacerboes 4 2 3 UNINSTALLING THE USB INTERFACE DRIVERS cccccccccseccseccecceseceecccuccececeeceeucseseceeecesecseseseeceensseseceeseesesuaes 5 2 4 INSTALLING ABRITES COMMANDER FOR TOYOTA LEXUS SCION eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 8 VEHICLE DIAGNOSTICS WITH ABRITES COMMANDER FOR TOYOTA LEXUS SCION 10 3 1 O16 1 5 61010 TION a E A S A E EA eee 10 sAd Danos ie POLO COL POUD aeran ee TEENA EE ETEA Il 3 1 2 Interface detection COM Port group cccccccccccccccccccceneeessseeeeeeeeeeeeeee eee e eee eee e AA AAA ddEEEEEEEEEEEEEE EEE EEE aG EGG aaa aaa EEE EE Il Jd K Line
12. Dand Kate SCUINCS crvcessieniesesinnsterviinstanviadnstensiiasiavs asrieutidntisaoilavlousdeasinnstcnsGontiluntesaadaeastiatsusiaastensics 12 de AOI OD cats ais vane E E A E seks onan ge acuasstece E naa ves N E ea otan is eaamae aes 12 I SC ANNIN ONIE ois E N ee 14 a A E E EE E AR A E T E R 14 Do CO TG A T EA A E AEA E A AA TEA AA 15 Daa SON E a a E E E E E E E E T nse comaceneeetane xs 15 3 3 STANDARD DIAGNOSTIC REQUESTS csccsecssccsccssccscesccsscsccnscscescessescesscsccuccescessessescesccscescescessessencescusceseenees 17 CEE E E E NE E E ET E ENE E E E E E E E IE E E E IS i fa C D Cs renee a Rn een ee Re ene en EAE O a ee nee IS ie es a 16 6 BY e ene e nn tee re rent kent rrr te enre E E ere tener tet cre ene errr tree E ere ee erent I8 BoA CUI DI a E E EA EEIE EA O E E O 19 des ACTO TO EEE EE EEE E TEE EE EEEE EEE E EEEE EE 19 w E N a E E E S E E E E E ee ee 19 Be A E E E A E E E E A A O N E SIRI E O E T 19 B OTOT T EE E A E EEA EE A E EE EEE E 19 3 3 9 Custom download upload oooeeeeeeennnnnnnnnnnnnnnnnnnnssssssssssseeerrrrssssssssssssseeterresessssssssssseeerrresessssssssssseeeereeeeo 20 3 4 BPE GIy PORC TION a E E seapetecnrensienareresnnerennteso ers 21 W TO T a N E E E 21 Se COIS TO a a A E E EAA EE E E AEAN EE E E E OOE EEES 21 3 4 3 Reset the Immobilizer and Key Learning cccccccccccsssecccccccceceeeeeeeeceee eee neeeeeeeeee eee eeeeeeeeeeeaaaaeeeeeeeeseaaaaeeeeeeeeaas 22 IA IAI SYT ET KOSET ririri sare sex EEN INEO EA
13. TES software for ID 12001F Toyota ABRITES Commander for Toyota exe Page 9 of 36 3 VEHICLE DIAGNOSTICS WITH ABRITES COMMANDER FOR TOYOTA LEXUS SCION The ABRITES Commander for TOYOTA LEXUS SCION consists basically of two parts Standard diagnostic functions like reading clearing fault codes DTC scanning avalable devices in he car displaying actual values measured parameters performing actuator tests etc Special functions like Key Learning Immobilizer Reset and Dump Tool All devices which may be present in the car are listed in the main screen of the ABRITES Commander for TOYOTA LEXUS SCION If you want to connect to a specific device please double click on it or select it ant press the Connecf button The ABRITES Commander for TOYOTA LEXUS SCION will try to connect to the device using consecutively the following protocols KWP2000 over ISO transport protocol CAN KWP2000 over K Line with fast init Unless you change the standard connection process from Options tab You can choose which of these protocols to use when attempting to connect to a device as described in the Configuration section 3 1 Configuration The ABRITES Commander for TOYOTA LEXUS SCION can be configured by pressing the Options tab from the main screen The following dialog is displayed Page 10 of 36 ABRITES Commander for Toyota Lexus Scion 2 4 www ABRITUS 2 co
14. TROUBLESHOOTING Below you can find a list of typical problems and how to solve them Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION on the splash screen Interface NOT found is displayed Solution Please make sure that the USB interface drivers are installed properly You can look at the device manager the USB interface should appear as USB Serial Port COMxx where xx is the number of the port Ifthe interface is recognized OK then please try to unplug and plug it again into the USB slot and restart the ABRITES Commander for TOYOTA LEXUS SCION lf the interface is not recognized the USB interface appears with a yellow exclamation mark in the device manager then you can try to solve the problem by uninstalling and reinstalling the USB interface drivers see sections Installing USB interface drivers and Uninstalling USB interface drivers If the problem is still present you can try to set the used port manually as follows o Start the ABRITES Commander for TOYOTA LEXUS SCION o Press the Options button o Uncheck the Autodetect check box and enter the number of the port from the device manager o The changes will take effect after restart of the ABRITES Commander for TOYOTA LEXUS SCION NOTE Please take into account that the used port will change when inserting the USB interface into different USB slots so the manual setting o
15. d dump button The dump file can be read either via OBDII but also with a programmer especially for units where reading via OBDII is not possible As output the dump tool displays some data extracted from the input file and or makes some modifications to the input data If modifications were made for some sub functions there are no modifications made only data are visualized the user has to write the modified dump to desired file with the Save dump button and then this modified dump should be saved back to the device via OBDII or with a programmer If data are read written with a programmer the user must make sure that the proper byte order is used Because most of the programmers are reading the data on 16bit words the byte order in the dump depends on the used programmer some programmers produce dumps starting with the least significant byte and some produce dumps starting with the most significant byte This means that for the same unit two different programmers can produce different dumps For that purpose a button Swap bytes is provided This buttons changes alternatively the byte order into the dump So if after loading the dump file into the dump tool data cannot be extracted or modified please try to swap the bytes to get a correct result Page 23 of 36 Dump Tool E es 3 4 8 ECU Engine Control Unit The Engine Control Unit ECU special function provides you a possibility to read and write the
16. e cleared using the Clear DTC function of the software The software supports saving the information to a file by pressing Write log button Page 18 of 36 ABRITES 3 3 4 Current Data The ABRITES Toyota Lexus Scion Commander displays live data like Oil Temperature Fuel Level Engine Speed Battery voltage etc Please note that the current version of the Toyota Commander supports current data display only for certain modules 3 3 5 Actuator test With the help of the ABRITES Commander for Toyota Lexus Scion it is possible to activate of a particular actuator For example it is possible to activate the horn move electrical mirrors lock unlock doors and many others Please note that the current version of the Toyota Commander supports Actuator tests only on control units that use the CAN communication protocol 3 3 6 Read VIN Read VIN reads the stored in the device VIN Vehicle Identification Number Not all electronic control units support this service Please note that it is only available for units on CAN bus 3 3 7 Write VIN The Write VIN diagnostic request tries to change the stored in the control unit VIN Please note that it is only available for units on CAN bus WARNING After using this function most of the electronic control units update their internal memory when ignition is turned off and the current diagnostic session is closed Write New VIN xj oJ ra Update WIN Cancel 3 3 8 Custom req
17. ekz_GSTONDPInstx 6 exe Installing driver FTDI CDM Driver Installation process completed Press enter Remark If you are running Windows XP or Windows XP SP 1 temporarily disconnect your PC from the Internet during the installation of the drivers Now you can connect your USB dongle and USB interface to your PC Wait a few seconds until Windows notifies you that the new hardware is ready for use 2 3 Uninstalling the USB Interface drivers In case the installed USB drivers are corrupted and or stop working properly your USB Interface is not recognized by the PC you can try to fix the problem by uninstalling and then reinstalling them so that you start over from a clean slate Uninstalling the USB interface drivers can be done by running the FTClean program You can find it in the USB Interface Drivers sub folder of your ABRITUS Commander or download it from the Internet using the following link http www ftdichip com Resources Utilities FT Clean zip The following is a step by step explanation for using FTClean to remove the drivers Unpack and run FTClean exe Page 5 of 36 Y FTDI Clean Utility 1 0 VID Hex FTDI Clean System PID Hex Exit Status Ready Click on the Clean System bution FTDI Clean Utility 1 0 P o x Information Disconnect all FTOI devices from the Pc a ean Sustem VID H FTDI FIE F re status Ready Disconnect a
18. f the port should be repeated in this case lf the problem is still present please run the ABRITES Commander for TOYOTA LEXUS SCION and try to auto detect the interface and generate a dump from the interface Report about the problem to Abritus72 Ltd with the included interface dump file Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION on the splash screen neither Interface found nor Interface NOT found is displayed Solution Please try to unplug and plug the dongle and the USB interface again into the USB slot and restart the ABRITES Commander for TOYOTA LEXUS SCION Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION the splash screen is displayed but the application freeze on this state for about 1 2 minutes After that Interface found is displayed and application functions normally Solution Probably there are some bluetooth devices installed on the PC Please try to deactivate them temporally Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION a message Error code 0x10001 Please contact support abritus72 com with the Error code in the subject Page 26 of 36 Solution Please contact support abritus72 com and request and update for your interface Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION a message Error code 0x10002 Please contact support abritus72 co
19. flash memory of EDC15 and EDC16 engine control units Page 24 of 36 Engine Control Unit Special Functions Choose ECU type BOSCH EDC 16 A9 v Read Flash BOSCH EDC 15 C9 ooooocoo Wo oo doo00010 no oo EORaiE ane EE oooooo20 00 o0 00 oo 00 oo oo O00 o0 00 00 00 00 00 00 OO LLL eee ee eee oooo0030 oo OO OO 00 00 Of OD OD OO 00 00 00 00 00 OO OO LLL eee eee ewes M oooo0040 oo 00 00 oo 00 oo 00 O00 o0 00 00 00 Of 00 00 OO LL eee eee oooo0050 oo OO OO oo oo Of Of OD OO 00 00 00 00 00 OO OO LL ee eee oooo0060 oo oo 00 oo 00 oo oo oo o0 00 00 00 00 00 00 OO LLL eee eee eee 00000070 OO O00 00 oo 00 oo oo oo OO 00 00 00 00 00 OO OO LLL eee eee opoooogo oo oo 00 oo 00 oo oo oo o0 00 00 00 00 00 00 OO LLL eee ee eee oooo00090 oo oo 00 00 00 oo oo 00 o0 00 00 00 Of 00 00 OO sa s s s ss ssssesa OOOOO0RO oo OO OO oo 00 Of Of OD OO 00 00 00 Of 00 OO OO LLL eee ee OOOO00BO oo oo 00 00 00 oo oo O00 o0 00 00 00 00 00 00 OO LL eee ee ee eee ooooo0co oo 00 00 00 00 0o O00 Of o0 00 00 00 00 00 OO OO LLL ee eee oooo00DO oo oo 00 oo 00 oo oo oo o0 00 00 00 00 00 00 OO LL eee eee OOOOO0EO oo 00 00 oo 00 oo 00 00 o0 00 00 00 Of 00 00 OO LL eee eee eee OOOOO0FO oo 00 00 oo 00 oo oo oo o0 00 00 00 00 00 00 OO LL eee ee ee eee Oooo0100 O00 oo 00 Of 00 oo OO 00 Of o0 o0 OO 00 Of OO OD LL eee eeee Load frorn file 00000110 00 OO OO 00 00 Of Of o0 OO 00 00 00 Of 00 OO OO LLL eee eee 00000120 00 00 00 00 00 oo 00
20. ll FTDI devices from the PC and click on the OK button Page 6 of 36 FTDI Clean Utility 1 0 ioj x gt You are about to uninstall all FTOI drivers For VID 0x0403 and all PIDs l Do vou want ko continue Click on the Yes button FTDI Clean Utility 1 0 5 x VID Hex Fi TT x lean Sistem PIL f 2 Do you wank bo cancel driver uninstallation Click on the No buiton to start removing driver Page 7 of 36 FTDI Clean Utility 1 0 5 x VID Hex FTDI Clean System PID Hen Exit Status System clean completed Uninstallation has finished Important Do not forget to reinstall the drivers following the instructions from point 2 2 Installing the USB Interface drivers 2 4 Installing ABRITES Commander for TOYOTA LEXUS SCION The ABRITES Commander for TOYOTA LEXUS SCION is contained into the installation package so please run the setup program It will create a program group in the start menu and optionally a desktop icon The ABRITES Commander for TOYOTA LEXUS SCION program group contains the following icons Uninstall ABRITES Diagnostic Software Link for uninstalling ALL Abrites software components available on your computer ABRITES Commander for Toyota the ABRITES Commander for TOYOTA LEXUS SCION diagnostic tool LicenseViewer A special tool for checking the
21. m with the Error code in the subject Solution Probably the dongle is not inserted into the USB slot or it is not recognized by the device manager You can check in the device manager whether it is recognized It should appear as HID compliant device in the Human Interface Devices Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION a message Error code 0x10003 Please contact support abritus72 com with the Error code in the subject Solution Probably SW dedicated for another interface was run on your interface Please contact support abritus72 com with the Error code in the subject Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION a message Error code 0x10004 Please contact support abritus72 com with the Error code in the subject Solution Please contact support abritus72 com with the Error code in the subject Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION a message Error code 0x10005 Please contact support abritus72 com with the Error code in the subject Solution Please contact support abritus72 com with the Error code in the subject Problem When starting the ABRITES Commander for TOYOTA LEXUS SCION on the splash screen Interface found is displayed but is not possible to connect to devices especially through K Line Solution Make sure that if you
22. m ont seme Protocol Engine and Transmission 7 Automatic Transaxle 03 ABS Airbag SRS 04 05 06 07 08 Hybrid Vehicle Battery 09 Hybrid Gateway 10 Mirror Connect 11 Air Condition System 12 AHC 13 Air Suspension System 14 Intuitive P A IPA 15 ECB Gateway 16 ECM gateway lexi 17 Gateway i f S amp Vehicle Selection i Special Functions _ Options Diagnostic Protocol Iv CAN M K Line KWP2000 Immobilizer Cruise Control Hybrid Control COM port Logging K Line Baud Rate Settings M Autodetect IY Enable CAN log 104725 9600 paws B M Enable K Line log 9600 5 10472 o e NOTE changes regarding interface detection which you made in this dialog will be applied after 3 1 1 restarting the application Diagnostic Protocol group The meaning of the check boxes is as follows 3 1 2 Norm CAN when trying to connect to the device the commander will try to connect to it using KW P2000 over ISO transport protocol with baud 500KB s K Line KWP2000 when trying to connect to the device the commander will try to connect to it using KWP2000 over K Line with fast init with selected in K Line Baud Rate Setting group speed Interface detection COM port group ally the ABRITES Commander for TOYOTA LEXUS SCION USB Interface is recognized automatically but there is an option to set it manually So if
23. nder for TOYOTA LEXUS SCION window or by clicking Connect button you connect to the device to proceed with standard diagnostics for currently selected car module The following dialog is opened Page 17 of 36 Engine and Transmission a Establishing diagnostic session with selected unit Please WAIT Diagnose frh E k CKi l OF ET y y a Diagnostic requests Read History Current Custom DTCs DTCs Data Requests Actuator Test Clear DTCs Download Upload This dialog provides you the possibility to execute the following diagnostic requests 3 3 1 Read DTCs Read DTCs Read Diagnostic Trouble Codes will display all present errors in the specified control unit Diagnostic trouble codes data is stored in the vehicle computer internal memory when problems occur Checking DIC data can aid in specifying the cause of the trouble When you press this button the Toyota Commander will display all stored and pending diagnostic trouble codes with their complete description The software supports saving the information to a file 3 3 2 Clear DTCs Clear DTCs Clear Diagnostic Trouble Codes will clear all stored DTCs from the control unit 3 3 3 History DTCs History DTCs are trouble codes stored in the ECU when continuous and non continuous monitors 2nd trip fail History DTCs set in conjunction with Current DTCs and are not cleared by the electronic control unit monitor History DTCs can only b
24. o conformation sound from the car your remote is not recognised and will not working You can try to repeat Register Smart Remote 3 4 6 Add Key applicable for smart systems Add Key provides you a possibility to learn an additional key for the vehicle Possible when a working key is present 1 Open driver s door DO NOT CLOSE THE DOOR UNTIL YOU HAVE LEARNED AT LEAST 1 KEY 2 Insert key in the ignition slot do NOT turn ignition ON 3 From the special functions start function Immo Reset and wait until finished usually takes only a few seconds 4 From the special functions start function Register Key and wait until finished usually takes only a few seconds 5 Turn ignition ON with all keys needed for programming To cancel key programming procedure turn ignition ON and OFF 6 times quickly For a list of Supported vehicle models on which this special function can be used please see the Appendix 3 4 7 Dump Tool By using this special function it is possible to calculate odometer values reset odometer values and so on This application needs the EEPROM dump from the corresponding control unit After the dump is loaded some modifications will be made and you need to store the resulting dump as a new file which you can program with a special programmer into the device that the dump is from The dump tool receives as input a dump file from the corresponding unit input dump is loaded with the Loa
25. of supported vehicle models on which this special function can be used please see the Appendix 3 4 2 Register Key Register Key provides you a possibility to register new keys Procedure for adding keys 1 Open the driver s door DO NOT CLOSE THE DOOR UNTIL YOU HAVE LEARNED AT LEAST 1 KEY 2 Press the Start button of the vehicle and from the special functions select Immo Reset and wait until finished usually takes 15 17 minutes 3 Important note after pressing the Start button of the vehicle the Immo Reset procedure should be started within the next 5 seconds 4 Press the start button of the vehicle once The Instrument cluster will be illuminated like when ignition is on 5 From the special functions start function Register key touch with the key the start button and wait until the commander notifies you that the procedure has finished 6 Try that the key is working properly remote control should work too Page 21 of 36 7 Important note Do not close the driver s door before successful key registration If for some reason the key is not working try again the complete programming procedure or the procedure above starting from point 4 For a list of Supported vehicle models on which this special function can be used please see the Appendix 3 4 3 Reset the Immobilizer and Key Learning Procedure for resetting the immobilizer and learning one key Step 1 Open Driver s Door and do not close it
26. oo o0 00 00 00 Of 00 00 OO LLL eee eee ee eee O0000130 00 00 00 00 00 oo 00 00 00 00 00 00 00 00 00 OO LLL ee eee o0000140 00 00 00 00 00 oo oo 00 o0 00 00 00 00 00 00 OO LLL eee eee eee o0000150 00 00 00 00 00 oo oo 00 o0 00 00 00 00 00 00 OO LL ete eee eee OOO00160 00 OO o0 oo 00 Of Of OD OO 00 00 00 00 00 00 OO LLL eee eee ewes 00000170 00 00 00 00 00 oo oo oo o0 00 00 00 Of 00 00 OO LL eee eee ee eee OOOOO1EO Of OO OO 00 oo Of Of OD OO 00 00 00 00 00 OO OO LLL eee eee 00000190 00 00 00 00 00 oo oo oo 00 00 00 00 00 00 00 OO LL ee ee eee OOOO01AN oo oo 00 oo 00 oo 00 oo o0 00 00 00 00 00 00 OO LLL eee eee OO0001BO oo 00 00 00 00 oo oo oo o0 00 00 00 00 00 00 OO LL eee eee ee eee oooo001CO oo 00 00 00 00 oo oo oo o0 00 00 00 00 00 00 OO LL eee eee ee eee OOOO01DO Of OO OO oo 00 Of OD OD OO 00 00 00 00 00 OO OO LL eee ee t 4 3 4 8 1 Read Flash Read Flash button reads the Flash memory from the Engine Control Unit 3 4 8 2 Write Flash Write Flash button writes into the Flash memory of the Engine Control Unit the currently loaded in the application dump 3 4 8 3 Save to file Save to file button saves the Flash memory that has been read from the ECU to a file 3 4 8 4 Load from file Load from file button loads a dump file for programming into the ECU flash memory IMPORTANT You need to clarify the type of Engine Control Unit in the car before proceeding Page 25 of 36 4
27. run the ABRITES Commander for TOYOTA LEXUS SCION from a shortcut the working folder is set to the folder where the ABRITES Commander for TOYOTA LEXUS SCION executable is placed Problem The device connects sometimes to the device under K Line and sometimes not Solution Try to increase decrease the Wakeup echo delay timing parameter Problem The connection with the device under K Line is unstable Solution Try to increase decrease the Inter byte time Time between messages and Communication echo delay parameters Problem It is not possible to connect to a device through the K Line since it is possible to connect to it with other diagnostic tools Solution Try to change the baud sequence to 9600 10472 from the options dialog Page 27 of 36 Problem Some device cannot be read or unexpected behavior was found Solution Please enable the logging as described in chapter Logging group and send the corresponding log file to support abritus com Problem After Start up Hardware cannot be detected Solution Please unplug the OBD an USB plugs than plug again first USB than OBD restart ABRITES commander and you should have connected hardware Page 28 of 36 5 APPENDIX 5 1 Supported models for key learning Toyota Rav4 Toyota Yaris smart key Toyota Auris smart key Page 29 of 36 ES WtONs Toyota Land Cruiser 100 Toyota Land Cruiser
28. uests By using this function the user can send manually diagnostic requests to the corresponding control unit The example below shows a request 13 and the corresponding reply from the device Page 19 of 36 Custom requests Request 13 3 3 9 Custom download upload Custom download upload allows direct reading from the address map of the control device Take into account that in most cases a security authorization is required before you try to read write into the address map Page 20 of 36 3 4 Special Functions Special functions are unique for some electronic control units functions which are not supported by any other diagnostic tool Special functions are available from the main dialog of the application amp Vehicle Selection i Special Functions Options i ii iol al 11001 3 i iloon h gool y Immo Reset Register ker Smart System Register Smat Add Key Dump Tool Reset Remote The appropriate special function is opened by selecting it from the list box and double clicking on it or by selecting it and then pressing the Open button 3 4 1 Immo Reset Immo Reset Immobilizer Reset provides you a possibility to clear all programmed Keys in the Immobilizer memory WARNING After using this function all stored in immobilizer memory keys will be deleted For this reason it is strongly recommended to program at least one Key after using Immo Reset For a list
Download Pdf Manuals
Related Search