Home

User Manual

1. FrameStore All Input Signals Router All Input Signals K K K K K K All Input Signals Display Waveform Vectorscope Pan amp Zoom DVI OUTPUT Split Screen Generator HD SDI 1 HD SDI 2 Outputs HD SDI 3 HD SDI 4 lt To To Router Inputs Cinemage User Manual To Router Inputs Framestore All Output Signals Router Inputs Signal Gen 3D LUT All Output Signals Version 2 1 All HD SDI Inputs and Outputs can be linked as 2 Dual Link Inputs and 1 Dual Link Output 13 Front Panel There are 6 pushbuttons located on the Front Panel These pushbuttons correspond to the soft menus located above each button These pushbuttons allow for direct input to the various features of the Cinemage Monitor The menus are located in the lower unused portion of the active video screen The upper unused portion of the active video screen is used as a reference bar going from black to white across the top of the screen A trackball located on the lower right hand portion of the monitor This trackball is used for direct input for cursor positioning alpha numeric input and level setting Rear Panel The rear panel is the location of the On Off switch the input AC connector and the 24 volt DC XLR input connector There are also 4 threaded holes for 4 metric screws fo
2. Cinemage Supported Resolutions Video Format HD SDI DVI Software Release Date Version Computer Graphics DVI D 1920 x 1200 60 Hz see note 1 e 2 1 12 28 2006 Single Link 4 2 2 486i 59 94 see note 1 e 2 0 Released 576i 50 see note 1 e 2 0 Released 720p e e 2 2 2 15 2006 23 98 24 25 29 97 30 50 59 94 for DVI D 1080sF 23 98 24 25 29 97 30 Hz e e 2 2 2 15 2006 for DVI D 10801 50 59 94 60 Hz e e 2 2 2 15 2006 for DVI D 1080p 23 98 24 25 29 97 30 Hz e e 22 2 15 2006 for DVI D Dual Link 4 4 4 1080sF 23 98 24 25 29 97 30 Hz e 1 0 Released 10801 50 59 94 60 Hz e 1 0 Released 1080p 23 98 24 25 29 97 30 Hz e 1 0 Released 1 Framestore Cage LUTs amp OmniTek options operate only in HD modes Cinemage User Manual Version 2 1 99 EDID Extended Display Identification Data is a VESA standard data format that contains basic information about a monitor and its capabilities including vendor information maximum image size color characteristics factory pre set timings frequency range limits The information is stored in the display and is used to communicate to computer graphics adapter The system uses this information for configuration purposes so the monitor and computer system can work together Cinemage systems shipped before December 1 2006 did not have the EDID set in DVI input chipsets see Setti
3. 2200000000000000000000000000200000200000 000000000000 0000 000000000 65 Input EU T 182 8ucs douces iae ra nea Eti Ses t APR STEREO ARE E 66 Process Menu Input LUTs Input LUTs 1 amp D2 4 cesse eren 2000000000000 66 Load Input LUT T isisca cibis ete nike 66 Chapter 15 Process Pan and Zoom ceres eee eee ee eee ee eene setas eet en aset ea aset tn aee 67 Chapter 16 Display Cages Graticules e eee e esee ee eee eee ee ee eerte seen nu 69 Cages Enabled nannten 69 Gages Setup m S 69 Mask lg stand 70 Chapter 17 Display Heads Up Display 0000000000000000000000000000000000000000000000000000 71 Chapter 18 Display Split Screen e ceres eere ee eee eee eese eese eese sete eese teneo 72 Chapter 19 Display Scaler amp Deinterlacer e eee esee e eere ee eren entes 73 Chapter 20 Display Test Pattern Generator esee eren ee ee ee eee eene ee ennue 74 Chapter 21 Analyse Pixel Data Analysis 00000000000000000000000000000000000000000000 00000000 76 Cinemage User Manual Version 2 1 5 Chapter 22 Analyse Pixel Analysis Pan and Zoom ssccsssscssssssssesscssssscsseees 78 Chapter 23 Analyse Waveform Monitor eee ee ee ee eee eere ee eee sees seeeesseee 79 Ch
4. Main Menu Cinemage 2142 Route Process Display Analyse Presets t To navigate the Scaler and Deinterlacer menu select Display from the main menu the following menu will be displayed Display Menu Cages Heads Up Display Split Screen Scaler and Deinterlacer Test Pattern Generator On Off Cage A Enabled Hold amp Release for Cages Setup Hold amp Release for Setup Hold amp Release for Setup Scaler and Deinterlacer Select Scaler and Deinterlacer and the following menu will be displayed Display Menu Scaler and Deinterlacer Single Field Mode Scaler Mode Motion Compensation Enable Motion Compensation Gain On 64 Single Field Mode Allows you to view a single field of an interlaced video source at a time Press and hold to adjust the motion clamping of single field mode in order to smooth the juttering in between fields of moving video Cinemage User Manual Version 2 1 73 Scaler Mode Allows you to select between Pixel Accurate displaying and Re Sized to fill screen 1080 formats will automatically be displayed in pixel accurate mode Note The aspect ratio of video sources will be preserved on the display even if Re size mode is selected 4 3 SD or HD video can be resized to fill the screen vertically but not horizontally without Motion Compensation Enable Turns motion compensation on or off Motion Compensation Gain Sets the amount of compensation from 0 to 255 by rotating the trackball Not
5. On the front panel from the first menu hold down the button that says hold and release for setup until it flashes Select MANAGE PREFERENCES Select LOAD PREFERENCES FROM USB The new preferences are now being loaded Note that the process of reconnection happens in the background after the button is released Press BACK twice then select REMOTE FILE SETUP Select the file type that you are setting in this case stills If the file path appears here then reconnection was a success Note that the new path will only be saved to preferences again if the connection is complete Saving a preference Preferences refer to settings that are specific to a given machine and its network environment Some of these things such as a selected network path along with usernames and passwords might be sensitive material Passwords are stored in clear text so it is good practice to reset see reset below the preferences to clear a examp ny sensitive security information when necessary Here are some les of things that are stored in preferences 1 Network logons paths and passwords for remote file access 2 FTP server settings whether the server is enabled and current password 3 Web settings if the web server is enabled 4 Storage information whether the system is set to use local remote or USB storage for stills and various LUTs Cinemage User Manual Version 2 1 87 Once you have adjusted your
6. Stills Presets Input LUTs 3D LUTs t Cinemage User Manual Version 2 1 96 Enter the Change Remote Stills Path Change Login and Change Password menus to adjust the information contained in each Information can be entered using the trackball and the Select Next Character button Back Change Remote Stills Change Login Change Password Connect Now Path T T T Once the File Path Login and Password are set press the Connect Now button to enable remote access to file and remote storage Back Change Remote Stills Change Login Change Password Connect Now Path Calibration option Before navigating the menus plug the GretagMacbeth GMB calibration probe into the USB port From the main menu press the Setup Menus button Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Press to lockout menus t Then select the Video amp Display Setup button Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup Setup Setup Then select the Display calibration button Back Video Setup Display calibration t Then select the Measure button note do not select Auto Calibrate yet Auto Calibrate Manual Select calibration Blue Only Measure Backlight Brightness Calibration t If you are using the GMB EyeOne Pro place the probe on the white calibration tile provided with the probe and Select Press to Calibrate Probe Then place probe on the cent
7. TCP IP Machine name Reklease 1 2 r3 192 168 1 123 00 04 5F 82 56 A3 Cinetal 316453 t T From a Windows or Mac you may browse the network to find the Cinemage Monitor Cinemage uses a Universal Naming Convention based on its TCP IP Machine Name Cinemage User Manual Version 2 1 95 Remote File Setup Cinemage as a network appliance has the ability to remotely store and access important files such as Stills Presets Preferences Input Luts and 3D LUTs This allows for remote collaboration across your facility across the country or around the world The file paths and necessary login information can be edited within the Cinemage unit to allow for this remote file access From the Main Menu press the Setup Menus button Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets t Then enter the Network USB Datakey Setup menu Press to lockout menus Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup Setup t Then enter the Remote File Setup Menu Back Web FTP Setup Remote File Setup File Sharing Setup Wireless Setup USB Datakey Setup t The process is the same for setting up all four areas of the Remote File Setup Listed are the steps for Stills but they can be repeated for Presets Input LUTs and 3D LUTs Press the Setup Remote Storage Stills button Back Setup Remote Storage Setup Remote Storage Setup Remote Storage Setup Remote Storage
8. This may be caused by cable or routing issues ANC errors indicate loss of data carried in the ancillary data packets of the SDI transport Gamut errors indicate active video data has fallen outside the gamut indicated in the Gamut Violation Setup menus located in the Analyse Menus Pixel Data On OPTION Display the pixel data from the Pixel Data Analysis Menu The Pixel Data Analysis Menu allows you the select a specific pixel in active video and display the value in RGB or YcBcR base 10 data values Cinemage User Manual Version 2 1 71 Timecode Display a timecode overlay in the bottom center portion of the display Timecode Mode can be set to LITC VITC 1 VITC 2 or Off When using multiple sources if you route from a source displaying timecode to one that is not the monitor will hold and continue to display the last time code recieved from a source outputting valid timecode Chapter 18 Display Split Screen The Cinemage system provides a split screen generator that allows you to compare two sources simultaneously Note You must have a reference sync input either from a video input or the analog reference input to use the split screen generator Main Menu Cinemage 2142 Route Process Display Analyse Presets t To navigate to the split screen generator setup menus select display from the main menu The following menu will be displayed Heads Up Display Split Screen Motion Compensation Test Pattern Generato
9. Masked Area Mask Style Cage or Mask Choose whether the system displays a cage with or without a mask Masked Area Choose to mask the inner or outer cage area Mask Style Choose between black or darken Cinemage User Manual Version 2 1 70 Chapter 17 Display Heads Up Display The Cinemage system provides a Heads Up Display for important data concerning your video signal Main Menu Cinemage 2142 Process Display Analyse Presets t To navigate to the Heads Up Display setup menus select Display from the main menu The following menu will be displayed Display Menu Heads Up Display Split Screen Motion Compensation Test Pattern Generator On Off Cages Cage A Enabled Hold amp Release for Cages Setup Hold amp Release for Cages Setup Hold amp Release for Setup i Heads Up Display Setup From the Display Menu the Heads Up Display can be set to on or off To setup the Heads Up Display hold the button for 3 seconds and release Display Menu Heads Up Display Setup Input Status CRC ANC Gamut Errors Pixel Data Timecode On On On Input Status Displays the status of input 1 4 in the Heads Up Display Status indicates video signal present and video format Choices are on or off CRC ANC Gamut Errors Displays any CRC or ANC data packet errors in the video signal coming into video inputs 1 4 CRC errors indicate that the error checking in the SDI transport has found a problem with the data
10. Mode Wired Static DNS Address Wired Static IP Address Wired Static IP Subnet Wired Static IP Garteway 68 1 2 B DHCP Mode 169 254 219 120 Wired IP Mode Select between DHCP and Static modes This button will also give any static IP errors Wired Static DNS Address Displays current static DNS address Press to set DNS address Wired Static IP Address Displays current static address Press to set static address Wired Static IP Subnet Mask Displays current static subnet mask Press to set static subnet mask Wired Static IP Gateway Displays current static gateway Press to set static gateway Cinemage User Manual Version 2 1 52 Wireless Setup System Setup Network USB Datakey Setup Wireless Setup Menu Wireless Status Add Profile List Existing Profiles m all Existing profilies Enabled Wireless Status Loads all wireless profiles saved to the monitor and enables or disables the monitor s access to the wireless networks Add Profile Enters the profile configuration menu that allows you to set the SSID authentication method encryption type and encryption pass phrase necessary to access your wireless network NOTE Profiles can also be configured using an XML editor program and loaded into the wireless profile directory using the file sharing capability List Existing Profiles Lists all of the profiles that have been loaded as well as any errors that may have occurred while loading the profiles Delete All
11. Turning On The System asussssuussscussesenunn ki nun cro s evan arae aaro cv Lok daa rua aad nana 14 Chapter 2 Menu Over View ciccsvcsesscenccovessessoonssyecesessonseepeysensesvenssesnsasenerssetensennsvosvenes 15 M in MONU a a erahnen AR REN DE DOMO SO 15 Operator Men s 16 System IL e in 19 SUIDA I 21 Lockout Menu 14 11 eeeeeeeeeeeee el eese nnn n nnn n nena assa anna aaa n nne nasa anna a nn 22 Section 2 Setting Up Your System eee ecce e eee ee eese eene eene ena 23 Chapter 3 Setup Overview oe ee eee nnen oe eai ehe unt agere Pu Rp o sondas INS re 24 Setup ls 24 Chapter 4 Unit Information Menus 4 eee ee ee ee eee eee ene een aestas eee ta sete ta seta ue 25 Chapter 5 Video amp Display Setup 1 ecce ee eee eere eere ee ee ee eee toos tete see 27 Video SeCLUD 27 Display Calibration aussi eibi heroi vwd lori et bri bii Tinte bo nd 27 PTT EB T I eor 27 Syne SOUTO E aesae rarae 28 leid c ia dizcigni Mer 28 SDI TIMING a een 28 Input Limiting Moden na 28 Chapter 6 Display Calibration sssissciscciccivnsncssncdercentveoesvenssnsoucssendedoateasdvcneseesoeessitenss 29 PAGO G Ali Date E TTL 29 Manual Calibration cccccccccssssssssseseeeeeeeeeeeeeessse
12. USB Datakey for storage Cinemage User Manual Version 2 1 46 USB file Copy Accesses the menu to copy individual categories of files such as 3D LUTs Input LUTs Presets or Stills from the USB key to local memory or from local memory to the USB Key Setup Lockout with USB Key Writes an unlock file to the USB Key and locks the Setup Menus to keep further changes from being made within these menus Changes will only to be able to be made once the USB key with the unlock file has been inserted into the USB port of the unit This keyed lockout will persist through a power cycle of the monitor Updates Gives access to the Updates menu to install software updates revert from the last update generate license lock codes and update software licenses USB File Copy Menu Selecting USB File Copy from the USB Datakey Setup menu will give you the following menu System Setup Network USB Datakey Setup USB Datakey Setup USB File Copy Back H posed Copy ree From Copy Files to USB Back Returns you to the previous menu Disable USB Storage Disables the ability to save any files to a USB datakey When coupled with the keyed lockout of the Setup Menu will ensure that sensitive data such as proprietary 3D LUTs and stills of current productions are not able to be saved to a USB storage device Updates Menu From the USB DataKey Setup menu selecting Updates will give you the following menu Update From USB Generate Lice
13. Y 654 Cb 545 Cr 654 1034 539 On t From the Pixel Data Analysis menu select Pan and Zoom The following menu will be displayed Analyse Pixel Data Analysis Pan and Zoom Magnification Horizontal Mag Vertical Mag Freeze Frame 1x 1x 1x On Magnification Zooms into the video image Choose between 2x 4x 8x or 16x Horizontal Magnification Performs a horizontal zoom into the video image Choose between 2x 4x 8x or 16x Vertical Magnification Performs a vertical zoom into the video image Choose between 2x 4x 8x or 16x Freeze Frame Freezes the incoming video Cinemage User Manual Version 2 1 78 More Displays the 2 page of the pan zoom menus This page provides the ability to load a still into the display while zoomed in Still file location is selected in the Framestore Menu Pan When in zoom mode provides the ability to pan around the image The coordinates displayed are the location of the upper right hand pixel within the zoomed image Chapter 23 Analyse Waveform Monitor OPTION The OmniTek HD waveform monitor is integrated into the Cinemage monitor in one of three options Display Only OmniTek Waveform Display Only provides a standard SMPTE waveform monitor with a fixed YCbCr parade display in frame mode The user does not have control over gain timebase or fields lines HD OmniTek HD Waveform is a full functioning high definition video waveform monitor Du
14. an unlimited number of presets can be stored on network file servers or the USB datakey From the Preset Preferences Setup menu select Manage Presets System Setup Preset Preferences Setup Menu Back Manage Preferences Manage Presets Save Current As Startup Settings Clear Startup Settings Press to set current state as startup Press to erase startup settings t You will get the following Manage Presets menu System Setup Preset Preferences Setup Menu Manage Presets Choose Preset Location Save Preset as New Overwrite Existing Delete or Rename 0 Local 1 Preset Preset Choose Preset Selects the preset to rename or delete Location Selects the location from which you will choose presets to save or delete Save Preset as New Save current chosen preset with a new name in the selected location Overwrite Existing Preset Overwrites the chosen preset with the current system settings Delete or Rename Preset Allows you to rename presets with custom names or delete presets Startup Settings System Setup Preset Preferences Setup Menu Manage Preferences Manage Presets Save Current As Startup Settings Clear Startup Settings Press to set current state as startup Press to erase startup settings Save Current As Startup Settings Sets the current state of the monitor as the settings that will be applied every time the monitor reboots and will disable saving settings at power down Cinemage User M
15. bmp tif jog png File Location Selects the file location where still files are saved when saving stills from the framestore Choose between local network and USB Datakey Capture as Proxy Allows you to save the still as a smaller frame size Without saving as a Proxy file the standard sizing of the still is 1920x1080 Proxy Decimation Determines the re sizing factor of the still to be saved A decimation factor of 1 will save the still at 960x540 At a decimation factor of 2 will save the still at 480x270 At a decimation factor of 3 the file will be 240x135 and at a factor of 4 the file will be 120x67 More Advances to the next menu Process Menu Framestore Still File Management Menu 1 Save File Format File Location Capture as Proxy Proxy dpx Network Decimation Pressing the MORE button will give you the following menu Process Menu Framestore Still File Management Menu 2 Disable Auto Routing ln Reset New File Set New File Character A Framstore Menu Prefix Prefix Select Next Character Disable Auto Routing in Framestore Menu Turning this Disable on will allow you to capture and save stills in the background while the video continues to play on the display Reset File Prefix Erases changes made to the Still File prefix Set File Prefix Sets the file prefix for Still Frames Select next Character Selects the character you have selected with the character generator as the next chara
16. from the Main Menu Main Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Backlight i 20 5 Original Settings Press to lockout menus T Upon pressing the System Menus button you will get the following menu System menu Process E Display Analyse Presets Route The routing menu routes system video signals to the display HD SDI Outputs and 3D LUT and allows for toggling of Dual Link Mode Option Process The Process menu allows the user access to the Framestores Colour Grade Menu Input LUTs and Pan and Zoom Menus Display Cinemage User Manual Version 2 1 19 The Display Menu allows the user access Cage Graticule Generators the Head Up Display Motion Compensation and the Test Pattern Generator Option Analyse Option The Analyse Menu allows the user access to the Pixel Data Analysis Waveform and Vectorscope Display Output Measurement Range and Gamut Violations and Input Status menus Presets The Preset Menu allows the user quick access to various Preset operational conditions 20 Presets can be stored on the system These Presets can also be stored to a USB memory stick or on a network file server Cinemage User Manual Version 2 1 20 Setup Menus To access the Setup Menus select Setup Menus from the Main Menu Main Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Backlight 20 5 Origina
17. limited trial basis upgrade licences to unlock software based functions of the Cinemage unit such as the Waveform Monitor Vectorscope Dual Link Mode the Test Pattern Generator Framestore and 3D Luts Both of these tasks can be accomplished through the Updates menu located under the USB Datakey Setup Menu To perform a software update with the update loaded from the Cine tal website to a USB key start at the Main Menu press the Setup Menus button Press to lockout menus Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets t Then enter the Network USB Datakey Setup menu Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup Setup Setup t Then enter the USB Datakey Setup menu Back Web FTP Setup Remote File Setup File Sharing Setup Wireless Setup USB Datakey Setup t Then press the Updates button Back Format amp Prepare Prepare USB Clone System to Clone USB Datakey Updates USB Key DataKey USB Datakey to System Insert the USB key and press the Update From USB Key button Update From USB Revert Last Generate Licence Update Licence Key Update Lock Code t The unit will load the software update into internal memory Power cycle the unit and the update will be loaded and ready for use Cinemage User Manual Version 2 1 92 To perform a software upgrade insert your USB key and press the Generate Licence Lock Code button Update
18. using the trackball located at the right of the monitor Effects of the bias adjustment will be more visible towards the black end of the shading spectrum Blue Bias Allows you to adjust the monitor s response curve upwards for the Blue component by using the trackball located at the right of the monitor Effects of the bias adjustment will be more visible towards the black end of the shading spectrum More Advances to the next menu Flat Field Display Sets the display to a flat field of black 17 progressively brighter shades of grey 100 white 100 red 100 green and 100 blue for display measurement and calibration Cinemage User Manual Version 2 1 33 Display Setup Manual Calibration Menu 2 x y R G B Bias and Gain menu 1 Red Bias Green Bias Blue Bias Flat Field Display poa Pressing the More button will display the following menu Display Setup Manual Calibration Menu 2 x y R G B Bias and Gain menu 2 Red gain Green Gain Blue Gain More Flat Field Display ped eles Back Returns to the x y R G B Bias and Gain menu 1 Red Gain Adjusts the monitor s response curve by adding a multiplier to the red component curve by using the trackball to the right of the monitor Effects of the adjustment to gain settings will be more visible towards the white end of the shading spectrum Green Gain Adjusts the monitor s response curve by adding a multiplier to the green component curve by using the trackb
19. Adjust x y R G B Options and Contrast Bias and Gain Selecting Set White Point and Gamma will display the following menu Display Setup Manual Calibration Menu 1 Set White Point Back Update Display Colour Observer Profile Temperature Update Display Profile Performs a new auto calibration of the display Colour Temperature Allows you to select from 12 user definable white points or select a custom white point The Custom white point moves in steps of 100 K and ranges from 4000 K to 9800 K and is controlled by the trackball to the right Observer Selects the observer of 10 degrees CIE 1962 or 2 degrees CIE 1931 If you don t know what this means please leave it at 2 degrees Cinemage User Manual Version 2 1 31 Display Setup Manual Calibration Menu 1 Back Calibration Set White Point Brightness Adjust x y R G B and Contrast Bias and Gain T Pressing the Brightness and Contrast button will display the following menu Options Display Setup Manual Calibration Menu 1 Brightness and Contrast Reset Brightness Reset Contrast Brightness Contrast Brightness 0 Back Returns you to the Manual Calibration menu Reset Brightness Resets any adjustments made to the brightness setting back to their original position Reset Contrast Resets any adjustments made to the contrast setting back to their original position Brightness Selects the brightness setting for adjustment controlled b
20. Cine tal Cinemage User Manual Cine tal Systems Inc 8383 Craig Street Suite 130 Indianapolis IN 46250 Cinemage User Manual Version 2 1 FCC Notice This device complies with Part 15 of the FCC Rules To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications This equipment has been tested and found To comply with the limits for a class A digital Device pursuant to Part 15 of the FCC Class rules These limits are designed to Provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which the user will be required to correct the interference at his own expense WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE USE THE RECOMMENDED ACCESSORIES ONLY Cinemage User Manual Version 2 1 Preface This User s Guide includes instruction and reference information for the operation and use of Cinemage 2142 Cinemage 2122 Cinemage 2042 Cinemage 2022 All options ava
21. Cinemage User Guide is intended to be a learning tool for those new to the Cinemage product as well as a handy reference for experienced operators The User s Guide offers step by step instructions and general information If you are new to the Cinemage products we strongly suggest that you read this manual completely and familiarize yourself with all the tasks presented An investment in time now may save a lot of time later Cinemage User Manual Version 2 1 11 Cinemage User Manual Version 2 1 Connections Starting from the top down DVI Output Connection to external monitor or projector 1920 x 1200 resolution at 48 60 Hz Video Out 1 0 0 ccc cece ra HD SDI Out 1 Video Out 2 HD SDI Out 2 Video Out T amp 2 cece ee eeeeeeeeeenaeenas Dual Link Out 1 DVI Input cua cxi iere oe ni nori d Input from computer device 1920 x 1200 resolution at 48 60 Hz Reference Loop eueeuess Analog Reference Video Input 4 sseeususesssseseeseeseses HD SDI Input 4 Video Input 3 ssssesssessesseseeeese HD SDI Input 3 Video Input 3 amp 4 sssesussusus Dual Link Input 3 amp 4 Video Input T HD SDI Input 2 Video Input d T HD SDI Input 1 Video Input 1 amp 2 Dual Link Input 1 amp 2 USB Connector Storage or Calibration Probe Network Connection Gigabit Ethernet Block Diagram HD SD HD SD HD SD HD SD DVI Input Signal Gen
22. Display Setup Manual Calibration Menu 2 Adjust High Mid Low menu 1 Back Segment to Modify Adjust x Adjust y Adjust Y High Adjust x 0 Back Returns to the Manual Calibration menu 2 Segment to Modify Selects either the High Mid or Low segment of the monitor s response curve to make adjustments to High refers to the 1 3 of the curve closest to white and Low refers to the 1 3 of the curve closest to black Adjust x When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the x color coordinate for the selected segment of the monitor s response curve Cinemage User Manual Version 2 1 36 Adjust y When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the y color coordinate for the selected segment of the monitor s response curve Adjust Y When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the luminance Y coefficient for the selected segment of the monitor s response curve More Advances to the next menu Display Setup Manual Calibration Menu 2 Adjust High Mid Low menu 1 Segment to Modify Adjust x Adjust y Adjust Y ES x L L High T Pressing the More button will display the following menu Display Setup Manual Calibration Menu 2 Adjust High Mid Low menu 2 Back Segment to Modify Adjust R Adju
23. Existing Profiles Deletes all of the files located in the Wireless Profiles folder in the Cinemage directory Steps to connect Cinemage to a network router Before connecting the Cinemage unit to your network always check with your network administrator 1 Determine if your network will require the Cinemage unit to be set for static IP or dynamic IP DHCP addressing Typically most networks use dynamic addressing 2 Go to the System Setup Network USB Datakey Setup Wired Wireless Setup Menu 3 Under the menu item Wired Mode set the system for either DHCP mode or Static IP 4 Ifthe system is set for DHCP Mode skip step 5 5 If the system will be set for Static IP setup the appropriate numbers for Wired Static IP address Subnet Mask and IP Gateway See Appendix A to edit this in the prefs xml file 6 If you desire to restrict access to files stored on the Cinemage unit you may restrict access by setting a user name and password for local network access If security is not a concern the default setting is a username of guest with no password Go to the file sharing setup menu System Setup Network USB Datakey Setup File Sharing Setup Menu To setup a username and password 7 Inthe File Sharing setup menu reset the systems network status by toggling the File Sharing Status menu from enabled to disabled and back to enabled 8 Goto the machine information menu Top Menu Back Machine Information Cinemage User Ma
24. File to Rename Delete Browse files located at chosen file location local network USB Datakey to choose a file to rename or delete Delete File Deletes selected file Reset New Name Resets the new file name under construction Rename File Now Renames the selected file with the name shown Select Character Selects the character displayed under the trackball and advances the cursor to the next position Character Use trackball to set character Framestore Setup The framestore setup menu sets the file location and prefix for saved files captured with the framestore To navigate the framestore setup menu select hold and release the back button from any framestore menu Process Menu Framestore Framestore Menu 2 Back Framestore Mode Cone amp Save Sequential Capture Framestore Still File Current Framestore 15 ___ View Source 1106 0004 dpx Hold amp Release for Framestore Setup t The following menu will be displayed To Framestore Source Management Process Menu Framestore Still File Management Menu 1 Save File Format File Location Capture as Proxy Proxy dpx Network Decimation Back Framestore Setup Press once to return to the Process Menu Press and hold for 2 seconds then release to go to the Framestore Setup Menu Cinemage User Manual Version 2 1 61 Save File Format Selects the still file format used when saving stills from the framestore Formats supported include dpx
25. From USB Revert Last Generate Licence Update Licence Key Update Lock Code t This will install a licence lock code onto the datakey Remove the USB key from the Cinemage unit and insert into the USB port on your computer Mac or PC In the Cine tal directory on the USB key you will find a file named lock_abcdef lic where abdef is the last 6 digits of the Cinemage unit s serial number Email this file to your Cine tal dealer The dealer will email back both your original lic file and its matching unlock license Move both of these files downloaded form the email into the Cine tal directory on the USB key Make sure that serial number on the lic file matches the serial number of the unit you are working on Insert the USB key back into the Cinemage unit Press the Update Licence button Update From USB Revert Last Generate Licence Update Licence Key Update Lock Code t Unlock result will then be displayed as either Success or Failure Failures will typically result from mismatched or outdated lock unlock files Outdated files occur if you do multiple upgrades out of order Once Success is displayed remove the USB key and power cycle the unit The upgrade will now be installed and fully operational Cinemage User Manual Version 2 1 93 Accessing a router To take advantage of Cinemage s networking and file sharing capabilities often it will be necessary to access the unit via a network r
26. LITY EXCEPTING THE WARRANTY EXPRESSLY ACKNOWLEDGED HEREUNDER CINE TAL HEREBY DISCLAIMS AND CUSTOMER HEREBY WAIVES ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY Limitation of Damages Cine tal shall not be liable to Customer under the Warranty for any consequential exemplary incidental or punitive damages regardless of whether Cine tal has been advised of the possibility of such damages in advance or whether such damages are reasonably foreseeable Force Majeure Cine tal shall not be liable to Customer for failing to perform its obligations under the Agreement because of circumstances beyond the control of Customer Such circumstances shall include but not be limited to any acts or omissions of any government or governmental authority natural disaster act of a public enemy riot sabotage dispute or differences with workmen power failure delays in transportation or deliveries of supplies or materials acts of God terrorism or any events reasonably beyond the control of Customer Indemnification Customer shall release defend indemnify and hold harmless Cine tal from and against any claims damages and liability arising from use of the Software or Documeniation by Customer To Obtain Warranty Service and Customer Support The following information describes our current warranty support procedures These proce
27. Manual Version 2 1 43 More Advances to the next menu System Setup Preset Preferences Setup Menu Manage Preferences 1 Back Reset Preferences to Load Preferences Save Preferences to USB Reload Preferences Default fromUSB Pressing the More button wil give oyu the folowing menu System Setup Preset Preferences Setup Menu Manage Preferences 2 Back Save Preferences Trackball Sensitivity Auto Blackout Time Save Preferences Saves your preferences settings to the location you have specified either Locally to a USB Key or to a Network Device Trackball Sensitivity Sets the sensitivity of the Trackball is determined by pressing the button until the desired level is attained Auto Blackout Time This is a screensaver function to help eliminate any LCD burn in that may happen with the menus and the upper reference bar The time selected is the amount of time that must pass without any menu selections being made before the blackout will occur Only the menus and the upper reference bar will be blacked out Any sources routed to the display will remain visible Choices of Blackout Times include 15 seconds 30 seconds 1 minute 5 minutes 20 minutes 1 hour 8 hours and 24 hours Cinemage User Manual Version 2 1 44 Manage Presets The Manage Presets menu provides management of the naming and storage locations of your presets Up to 20 presets may be stored on the local system and
28. Menu Cinemage 2142 Operator Menus _ System Menus Setup Menus Display Controls Presets Original Settings Press to lockout menus T Upon pressing the Operators menu button you will get the following menu Operator Menus Internal Presets 3D LUTS Stills Operator Menu Back Source Routing Upon pressing the Video Input Routing Menu button you will get the following menu Operator Menus Video Input Source Select Preset gt SDI 1 SDI 2 SDI 3 SDI 4 DVI Input FULLMODE Video Sources Back Selected L Operator Menus Video Input Source Back Returns you to the Main Menu SDI 1 Routes SDI input 1 to the display A highlighted button indicates the current source that is routed to the display SDI 2 Routes SDI input 1 to the display A highlighted button indicates the current source that is routed to the display SDI 3 Option Routes SDI input 1 to the display A highlighted button indicates the current source that is routed to the display SDI 4 Option Routes SDI input 1 to the display A highlighted button indicates the current source that is routed to the display DVI INPUT FULLMODE Option Routes the DVI Input to the Display See FSB 061220 on page 99 for details Cinemage User Manual Version 2 1 16 Menu Navigation Use the trackball to select which operator menu to be displayed Operator Menus Internal Source Operator Menus Internal Source Select Internal Source gt Test P
29. Now Loads the file selected in the Browse Files Button More Displays Framestore Menu 2 Current Framestore Use the trackball to select which framestore you are viewing In Live Mode the trackball will select which framestore you will store a captured still frame Framestore Menu 2 The second framestore menu provides a capture and save function along with a sequential capture function To navigate the framestore menu 2 select More from framestore menu Process Menu Framestore Framestore Menu 1 Back Framestore Mode Capture Browse Files Load File Now Current Framestore Live File_name dpx File name dpx B Hold amp Release for Framestore Setup The following menu will be displayed Process Menu Framestore Framestore Menu 2 Back Framestore Mode Save Frame Sequential Capture Framestore Still File Current Framestore Live 1106 0004 dpx To Framestore Source Management 15 SDI 1 M Hold amp Release for Framestore Setup Back Framestore Setup Press once to return to the Process Menu Press and hold for 2 seconds then release to go to the Framestore Setup Menu Cinemage User Manual Version 2 1 59 Framestore Mode Switches the framestore mode from displaying the video source routed to the framestore input View Source to displaying the output of the framestore listed under Current Framestore The Current framestore is selected by the trackball Save Frame Capture
30. Original Settings Press to lockout menus Each menu item corresponds to one of six buttons found directly underneath each menu The seventh menu item far right menu is controlled by the trackball Cinemage 2142 Indicates Cinemage model number By pressing this button once you will navigate to the Lockout Menu The Lockout Menu provides two functions 1 to blackout the non video portion of the display and 2 provides a key lock function such that the systems setting can t be changed without an unlock key see Lockout Menu in chapter 2 for more information Operator Menus The Operator Menus provide an easy menu interface for selecting the video input selecting internal video sources and selecting presets of system configurations saved as a preset This is designed to be the menu used during normal operation of the monitor System Menus The System Menus navigates the user to the full system menus including all route process display analyze and setup functions Setup Menus The Setup Menus navigates the user to all system setup functions and to the system reset Display Controls Will enter the Display Control Menu allowing you to display characteristics such as brightness contrast gamma and backlight brightness Presets Allows you to toggle Presets previously saved into the system Cinemage User Manual Version 2 1 15 Operator Menus To access the Operator Menus select Operator Menus from the Main Menu Main
31. Preference settings i e designated a Network Path it may be useful to save that setting to a USB key for later recall to enable you to reset the machine to clear any sensitive information To save or recall your preference settings enter the Setup menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Press to lockout menus t Then enter the Presets Preferences Setup Menu Back Video Setup Display Setup Preset Preferences Network USB Reset Setup Setup t Then enter the Manage Preferences Menu Back Manage Preferences Manage Presets t From here you can either load your preferences from a USB key or save them off to a USB key Reset Preferences to Load Preferences Save Preferences to USB Trackball Sensitivity Auto Blackout Time 4 Default from USB 1 hour Saving a Preset Presets files describe the way the system interacts with video and how it s used in the workflow Presets are loaded from the front panel at the top level menu when you press the button the preset file is loaded and the name of the file appears Here are some examples of things that are stored in a presets file 6 Cage Graticule size and position 7 Video standard if not in automatic mode 8 Heads up display settings 9 Dual link mode vs Single link mode 10 Routing Saving your presets allows you quick access to your desired workflow Presets can be saved to and recalled from any of three
32. SE FROM YOUR USE OF OR INABILITY TO USE THE SYSTEM FOR COMMERCIAL LOSS OF ANY KIND FOR THE PROCUREMENT OF SUBSITIUTE GOODS WHETHER ARISING IN TORT CONTRACT OR ANY OTHER LEGAL THEORY EVEN IF CINE TAL SYSTEMS LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN ANY EVENT CINE TAL SYSTEMS LLC S LIABILITY SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE SYSTEM GIVING RISE TO ANY SUCH DAMAGE THIS LIMITATION IS INTENDED TO LIMIT CINE TAL SYSTEMS LLC s LIABILITY AND SHALL NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY Software License Agreement IMPORTANT READ CAREFULLY This Software License Agreement is a legal agreement between Cine tal s Customer and Cine tal Systems LLC This system contains certain Cine tal Systems computer software hardware associated media printed materials and electronic documentation By using the system described in this manual The Customer agrees to be bound by the terms of this Software License Agreement If The Customer does not agree to the terms of this Software License Agreement Cine tal Systems LLC is unwilling to license the Software to The Customer In such case The Customer may not use or copy the Software This system also contains certain third party software licenses included and contained with the materials shipped with the system License Cine tal Systems LLC grants a nonexclusive personal perpetual nontransferable limited license to use the instal
33. Sharing Setup Wired Wireless Setup USB Datakey Setup Web FTP Setup Web services and FTP services can be controlled with this menu When selecting WEB FTP Services you will get the following menu System Setup Network USB Datakey Web FTP Services Web Server FTP Server Fixed FTP User name Current FTP Change FTP Password Enabled Enabled ftp user Password Web Server Turns Web Server on or off When Web Server is on individuals with network connections can access the Cinemage unit through a standard web browser See Web Browser Menus FTP Server Turns FTP Server on or off When FTP Server is on individuals with network connections can upload and download stills LUTs waveforms and presets through a standard FTP client Fixed FTP Username The FTP username is fixed and cannot be changed Current FTP Password Displays the current FTP password in PLAIN TEXT Change FTP Password The FTP password can be changed through this menu Cinemage User Manual Version 2 1 49 Remote File Setup Remote file setup defines a network file server location for the system to store stills Input LUTs 3D LUTs and presets From the Network USB Datakey setup select Remote File Setup System Setup Network USB Datakey Setup Menu WEB FTP Setup Remote File Setup File Sharing Setup Wired Wireless Setup USB Datakey Setup t The following menu will be displayed Back Setup Remote Storage Setup Remote
34. Storage Setup Remote Storage Setup Remote Storage Stills Presets Input LUTs 3D LUTs Setup Remote Storage Stills This menu allows you to set a path login and password to a network file server for network storage of stills loaded to or saved from the framestore The Connect Now selection makes the remote connection to the file server from the Cinemage unit Setup Remote Storage Presets This menu allows you to set a path login and password to a network file server for network storage of Presets loaded to or saved from the system The Connect Now selection makes the remote connection to the file server from the Cinemage unit Setup Remote Storage Input LUTs This menu allows you to set a path login and password to a network file server for network storage of Input LUTs loaded to or saved from the system The Connect Now selection makes the remote connection to the file server from the Cinemage unit Setup Remote Storage 3D LUTs This menu allows you to set a path login and password to a network file server for network storage of 3D LUTs loaded to or saved from the system The Connect Now selection makes the remote connection to the file server from the Cinemage unit Cinemage User Manual Version 2 1 50 File Sharing File Sharing allows users on the network to have access to the local storage area on Cinemage Users may access locally stored stills LUTs waveforms and presets From the Network USB Datakey Setup Menu select Fil
35. acklight Brightness calibration Calibration Target x 314 y 345 t Make adjustments to the backlight for Luminance level and Manual Calibration settings as needed and re calibrate until you have the desired results Cinemage User Manual Version 2 1 98 Cine tal Field Service Bulletin 4061220 Title DVI Input Release Notes Date December 20 2006 Summary DVI is enabled on the Cinemage product line in two phases The first phase is on software version 2 1 In this release the Cinemage supports a DVI D or DVI I input at a fixed 1920x1200 resolution with a refresh rate of 60Hz The DVI input can not be routed to the HDSDI outputs Framestore or 3D LUT When the DVI input is selected it is calibrated and routed directly to the display at the full 1920x1200 resolution As this is the full resolution of the panel the menus and heads up display are not visible After selecting the DVI input users can return to the menus by selecting any button The standard use of the DVI input in version 2 1 is as a calibrated desktop display for a computer workstation with a DVI D or DVI I output supporting 1920 x1200 resolution at 60 Hz The second phase of DVI support will be in version 2 2 In the 2 2 release the DVI input will support several HD video related resolutions and frame rates These resolutions may be routed to HDSDI outputs Framestore or 3D LUT and is available as a source for the split screen and waveform monitor and vector scope
36. agick contributors and especially Bob Friesenhahn Copyright C 2003 GraphicsMagick Group an organization dedicated to making software imaging solutions freely available Permission is hereby granted free of charge to any person obtaining a copy of this software and associated documentation files GraphicsMagick to deal in GraphicsMagick without restriction including without limitation the rights to use copy modify merge publish distribute sublicense and or sell copies of GraphicsMagick and to permit persons to whom GraphicsMagick is furnished to do so subject to the following conditions The above copyright notice and this permission notice shall be included in all copies or substantial portions of GraphicsMagick The software is provided as is without warranty of any kind express or implied including but not limited to the warranties of merchantability fitness for a particular purpose and noninfringement In no event shall GraphicsMagick Group be liable for any claim damages or other liability whether in an action of contract tort or otherwise arising from out of or in connection with GraphicsMagick or the use or other dealings in GraphicsMagick Except as contained in this notice the name of the GraphicsMagick Group shall not be used in advertising or otherwise to promote the sale use or other dealings in GraphicsMagick without prior written authorization from the GraphicsMagick Group Cinemage User Manual Ve
37. al Link OnimTek Dual Link Waveform is a full functioning dual link high definition waveform monitor The menu items in this manual will vary depending on the waveform option enabled on your system Main Menu Cinemage2142 Route Process Display Analyse Presets To navigate to the Waveform Vectorscope menus select Analyse from the main menu The following menu will be displayed Analyse Menu Back Pixel Data Analysis Waveform Vectorscope Measure Display Output Gamut Violation Setup Input Status Cinemage User Manual Version 2 1 79 From the Analyse Menu select Waveform Vectorscope The following menu will be displayed Analyse Waveform Vectorscope Back Waveform Vectorscope Waveform Wave Mode Line Mode Selected Line 14 Vectorscope Off o Full Field Field 1 Hold amp Release for Waveform Setup Hold amp Rel Source E Back Returns to the Analyse Menu Waveform Vectorscope Source Selects the source routed to the display and to the Waveform Vectorscope Waveform Select to turn on and display Waveform Monitor Hold and release this button to go to Waveform Setup see Waveform Setup chapter 20 Vectorscope Select to turn on and display Vectorscope Hold and release this button to go to Vectorscope Setup see Vectorscope Setup chapter 21 Field Line Select the display mode of the waveform monitor to either Full Field or Single Line mode Selected Line When the waveform display mod
38. all to the right of the monitor Effects of the adjustment to gain settings will be more visible towards the white end of the shading spectrum Blue Gain Adjusts the monitor s response curve by adding a multiplier to the blue component curve by using the trackball to the right of the monitor Effects of the adjustment to gain settings will be more visible towards the white end of the shading spectrum More Advances to the next menu Set Flat Field Sets the display to a flat field of black 17 progressively brighter shades of grey 100 white 100 red 100 green and 100 blue for display measurement and calibration Cinemage User Manual Version 2 1 34 Display Setup Manual Calibration Menu 2 x y R G B Bias and Gain menu 2 Red gain Green Gain Blue Gain Flat Field Display o Pressing the More button will display the following menu Display Setup Manual Calibration Menu 2 x y R G B Bias and Gain menu 3 Back Returns you to x y R G B Bias and Gain menu 2 X y This trackball controlled menu item allows you to adjust the x and y color coordinates for the entire monitor response curve Adjustments will be displayed in the format of Ax Ay Setup Manual Calibration Menu 1 Calibration Set White Point Brightness Adjust x y R G B Options and Contrast Bias and Gain Pressing the More button on the Manual Calibration menu will advance to the second Manual Calibration menu and display Adjust Detailed R
39. anual Version 2 1 45 Clear Startup Settings Will remove the settings you have designated as Startup Settings and the monitor will revert to saving your settings on power down and restore your last saved settings upon power up Chapter 8 USB Datakey Setup The USB Datakey Setup Menu provides the ability to format a USB datakey and transfer data between the system and the datakey For a current list of compatible USB datakeys visit www cine tal com From the System Setup menu select Network USB Datakey Setup System Setup Menu Back Video Setup Display Setup Preset Preferences Setup Network USB Reset Setup t You will get the following Network USB Datakey Setup menus System Setup Network USB Datakey Setup Menu Web FTP Setup Remote File Setup File Sharing Setup Wireless Setup USB Datakey Setup Select USB DataKey Setup for the following menu System Setup Network USB Datakey Setup USB Datakey Setup Menu Format amp Prepare CLONE TO FROM USB File Copy Setup Lockout With Updates USB Key USB USB Key Format and Prepare USB Only use Format with a previously formatted USB Datakey This selection will completely erase all files and directories on the USB Device Once formatted the Key will have the Cine tal file format loaded on the device on the USB Datakey Clone System To From USB Accesses the menu to copy all preferences presets LUT s and stills from the local storage area to or from the
40. apter 24 Analyse Waveform Setup eese eee ee eese ee eee eese eese sees sssees esee SL Chapter 25 Analyse Vectorscope Setup c eeeeee ecce eene eee ee eene ee esseeesssee D Section 4 SD Operations aii eee nee eeepc Gace co D4 Appendix A USEFUL OPERATIONS eee ee eene ee ee eese oe oe eeess OD Cine tal Cinemage Preferences Control ee eee ecce esee eene e eene sees seeeessee OD Setting Remote File Locations 4 ee ee ecce esee ee eee ee eere eese seen sese ensese ense ee ensee OD Savins a preferences PRENNE orte Fen t ope en eu eher Saving uro ord E Cloning to from a USB key sccsecessscsoccssccsscseecssscoesscncesvncvedensivsncnevsnsedsenccsvcenssevscessesoves DO Software Updates Upgrades scssscssscssessessevonsssccostescasseveesesooasosonsersbensdensssssensvonsesveenes OL Aceessmo a FOULCE uic podio boe T c ud ape eoa Serasa DR PAD atos EOM GR DR RR iN OO Remote File Sep case Y Sere eire Paler coca eee ps ore rie ere nerd pde DO Calibration 55d ues ec eo ecce ue eous o ce vo ve cene ee een eo Coon aea eoe vn ao eae eva ea v vn ea oa eee aea vnus ao crer DVI Input Release Notes nee a 99 Cinemage User Manual Version 2 1 6 Official Notices Limitation of Liability CINE TAL SYSTEMS LLC SHALL NOT BE LIABLE FOR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR DAMAGES THAT DIRECTLY OR INDIRECTLY ARI
41. assume or create for it any other obligation or liability in connection with the Equipment except as set forth herein f THE WARRANTY IN SECTION 6 a ABOVE IS EXCLUSIVE AND IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Limitation of Liability INNO EVENT SHALL COMPANY BE LIABLE FOR ANY INDIRECT INCIDENTAL PUNITIVE SPECIAL OR CONSEQUENTIAL DAMAGES OR DAMAGES FOR LOSS OF PROFITS REVENUE OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY WHETHER IN AN ACTION IN CONTRACT OR TORT OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES COMPANY S LIABILITY FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THIS AGREEMENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE DEFECTIVE EQUIPMENT THE PROVISIONS OF THIS AGREEMENT ALLOCATE THE RISKS BETWEEN COMPANY AND CUSTOMER COMPANY S PRICING REFLECTS THIS ALLOCATION OF RISK AND BUT FOR THIS ALLOCATION AND LIMITATION OF LIABILITY COMPANY WOULD NOT HAVE ENTERED INTO THIS AGREEMENT Cinemage User Manual Version 2 1 8 Cine tal Software Warranty Cine tal represents and warrants that the Software shall perform substantially as represented in the Documentation WARRANTY LIMITATION THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES OF MERCHANTABI
42. ation Select Measure note do not select Auto Calibrate yet If you are using the GMB EyeOne Pro place the probe on the white calibration tile provided with the probe and Select Press to Calibrate Probe Then place probe on the center of the display If you are using the EyeOne Display 2 place the probe on a flat black surface the top of the monitor works well then press press to calibrate probe When finished place the probe on the center of the display Press Flat Field until you have 100 White displayed Adjust the backlight to a comfortable setting for your current ambient environment Press Measure Now Read the results for display luminance out Y under CIE x y Y Adjust the backlight 10 11 12 13 either up or down and repeat step 7 8 until you reached your desired luminance output setting The readout will be in both Candelas and Foot Lamberts Press the back button to return to the Display Setup Menu Select Auto Calibrate If you are using a GretagMacbeth EyeOne Display2 place the probe on a flat black surface the top of the monitor works well then press press to calibrate probe When finished place the probe on the center of the display If you are using the GretagMacbeth EyeOne Design place the probe on the calibration tile provided with the Eye One Design and Press Place Probe and Press Use the LCD mounting device provided with the Eye One Design and mount the probe on the middle
43. ation points you would like to make adjustments to in order modify the monitor s response curve If the Flat Field generator is in use the flat field will automatically update to a grey field that matches the point on the curve This allows the user to adjust the color balance and luminance at each point Adjust x When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the x color coordinate for the calibration point you have selected Adjust y When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the y color coordinate for the calibration point you have selected Adjust Y When selected this button allows you to use the trackball to the right of the monitor to make adjustments to the Luminance Y coefficient for the calibration point you have selected More Advances to the next menu Cinemage User Manual Version 2 1 38 Display Setup Manual Calibration Menu 2 Adjust Detailed Calibration Points menu 1 Back Point to Modify Adjust x Adjust y Adjust Y More duet x T Display Setup Manual Calibration Menu 2 Adjust Detailed Calibration Points menu 2 Point to Modify Adjust R Adjust G I Adjust B zu x 1 Pressing the More button will display the following menu Back Returns to the Adjust Detailed Calibration Points menu 1 Point to Modify Selects which of the 17 calibration points you would like t
44. attern Generator Framestore 3D LUT QUAD INPUT Main Menu Internal Source By using the trackball in the Operator Menus you can navigate to the Internal Source menu Back Returns you to the Main Menu Splitscreen Routes the splitscreen generator output to the display A highlighted button indicates the current source that is routed to the display Test Pattern Generator Routes the Test Pattern Generator output to the display A highlighted button indicates the current source that is routed to the display Framestore Routes the Framestore output to the display A highlighted button indicates the current source that is routed to the display 3D LUT Routes the 3D LUT output to the display A highlighted button indicates the current source that is routed to the display QUAD INPUT Option Displays all four HD SDI inputs at the same time in a 74 screen resolution Cinemage User Manual Version 2 1 17 Operator Menus Presets Operator Menus Presets Menu i por pss EE wp rats By using the trackball in the Operator Menus you can navigate to the Presets menus Each Preset menu page contains 5 presets starting with Original Settings and Defaults There are 20 Presets available in the system Use the trackball to advance the Operators Menus the next Presets page Preset 0 More Presets Main Menu Returns you to the Main Menu Save New Preset Will save your settings to the next available Preset This new Pres
45. ay Vectorscope Vectorscope Graticule Select the type of Graticule for the Vectorscope 100 or 75 Vectorscope Display Decay Gain Control of the refresh rate of the Vectorscope trace Vectorscope Display Decay Gain Control of the brightness of the trace Cinemage User Manual Version 2 1 83 Section 4 SD Operations Cinemage will accept and display SD video signals but with limited functionality Many of the video processing features available in HD Mode will not function in SD mode such as the Waveform and Vectorscope 3D LUTs Input LUTs Framestore and split screen generator The following menu applies only to SD video operation of the Cinemage unit SD Video Mode Main Menu Cinemage 2142 Standard Definition Mode Video Input Select Scaler Mode Display Control Scaler and Deinterlacer ress and hold for lockout menu SD 486i 29 97 Re sized to fit screen Cinemage Gives the model number of the Cinemage unit you are working on Pressing and holding for 2 seconds will access the Lockout Menu referenced previously in the manual Standard Definition Mode Gives the video format of your attached standard definition source Video Input Select Allows you to toggle the video input source between the 4 SDI inputs Scaler Mode Cycles through the re sizing options for the SD image from pixel accurate to re sized to fit screen 4 3 Aspect ratio to 16x9 525 16 9 aspect ratio Display Control Accesses the previ
46. cter in your file prefix Cinemage User Manual Version 2 1 62 Character Adjusts the character by rotating the trackball Cinemage User Manual Version 2 1 63 Chapter 13 Process Colourgrade OPTION The Process menu provides access to the Framestore Colourgrade and Input LUT functions Main Menu Cinemage 2142 Process Display Analyse Presets To navigate the Colourgrade menus select Process from the main menu the following menu will be displayed Process Menu Back Framestore Colourgrade Input LUTS Pan and Zoom t Select Colourgrade from the Process menu and you will get the following menu Process Menu Colourgrade Back 3D LUT Source Display Source Browse 3D LUTs Load 3D LUT Now Reset 3D LUT Framestore 3D LUT Output Bypass a3d Bypass a3d Hold amp Release for Framestore Setup 3D LUT Source Choose the source for the 3D LUT All four HD SDI inputs or 2 Dual Link inputs Framestore Test Pattern 3D LUT Output and DVI Input can be routed as an input to the 3D LUT Display Source Routes the system sources to the display Browse 3D LUTs Select a LUT to be loaded into the 3D LUT LUTs can be browsed locally from a network source or USB Load LUT Now Loads the selected LUT into the 3D LUT Reset 3D Lut Removes the 3D LUT from the video being displayed Cinemage User Manual Version 2 1 64 Chapter 14 Process Input LUTs The Process menu provides access to the Framestore Colourgrad
47. dures are subject to change without notice and are expressly excluded from the Limited Warranty e Our Customer Support Representatives are available to provide telephone support during business hours M F 8am 8pm EST and after these hours for urgent emergency technical support e Before returning the Product for repair or replacement it is necessary to obtain a Return Merchandise Authorization RMA number by calling 317 576 0091 You will be asked to provide the system s serial number or a copy of the invoice showing date of original purchase and or the Hardware Maintenance Agreement number e In order to provide you with an exchange unit in advance of receiving the non functioning unit we will need i a company purchase order for the value of the unit being provided ii the serial number of the component being returned Your PO will not be billed if the non functioning unit is returned as described below within 7 days e The non functioning part should be properly packed and shipped pre paid to CINE TAL with the RMA number clearly displayed on the outside of the package and on the Cinemage User Manual Version 2 1 9 accompanying RMA form We will refuse to accept any package without a valid RMA number e Normal labor material and shipping charges will apply to repairs outside the scope of the Limited Warranty This product includes some software from the GraphicsMagick Group Cine tal wishes to thank all the GraphicsM
48. e The Motion Compensation adjustment will provide an adjustment to minimize motion artifacts It is recommended to have motion compensation on only when viewing video signals that are interlaced such as 1080i Chapter 20 Display Test Pattern Generator As an option Cinemage contains a full Test Pattern Generator that is routable downstream through either of the HD SDI outputs or the optional DVI Output Main Menu Cinemage 2142 Route Process Display Analyse Presets jj To navigate the Test Pattern Generator menus select Display from the main menu the following menu will be displayed Display Menu Back Cages Heads Up Display Split Screen Motion Compensation Test Pattern Generator Cage A Enabled On Off Hold amp Release for Cages Setup Hold amp Release for Setup Hold amp Release for Setup Display Menu Test Pattern Generator Back Segment Pattern Segment Size Flat Field Full Screen Generator Control Control Generator Hold amp Release for Setup Segment Pattern Control Enters the Segment Pattern Control Menu which allows you to assign up to 4 different Test Patterns to horizontal segments of the screen as well as assign a separate pattern to the upper portion of the screen Cinemage User Manual Version 2 1 74 Segment Size Control Enters the Segment Size Control menu which allows you to adjust the height of the horizontal segments of the display to customize your test pattern Flat Field Ge
49. e Sharing Setup System Setup Network USB Datakey Setup Menu WEB FTP Setup Remote File Setup File Sharing Setup Wired Wireless Setup USB Datakey Setup The following menus will be displayed System Setup Network USB Datakey Setup File Sharing Setup Menu Fixed Network ID Fixed Sharing Username Sharing Password File Sharing Status CINETAL 0511908 Guest No Password Only Fixed Network ID Displays the network ID for the machine Fixed Sharing Username The username for the system is fixed at guest You can t change the username Sharing Password The password for file sharing is fixed at no password File Sharing Status Allows you to turn file sharing on or off and displays the current status of file sharing Note It may be necessary to cycle file sharing from enabled to disabled and then back to enabled to reset the network connection and allow access to Cinemage s files from a remote computer Cinemage User Manual Version 2 1 51 Wired Wireless Setup From the Network USB Datakey Setup Menu select Wired Wireless Setup WEB FTP Setup Remote File Setup File Sharing Setup Wired Wireless Setup USB Datakey Setup The following menus will be displayed Back Wired Setup Wireless Setup Wireless Setup OPTION Select to go to the wireless setup menu Wired Setup Select to go to the wired setup menu System Setup Network USB Datakey Setup Wired Setup Menu Wired IP
50. e and Input LUT functions An Input LUT may be applied to the incoming video Input LUTs are independently applied to inputs 1 amp 2 as a pair and inputs 3 amp 4 as a pair Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate the Input LUT menus select Process from the main menu the following menu will be displayed Process Menu Back Framestore Colourgrade Input LUTS Pan and Zoom t Select Input LUTs from the Process menu and you will get the following menu Process Menu Input LUTs Input LUT Location Input LUTs 1 amp 2 Input LUTs 3 amp 4 File Management Input LUT Location Selects location from which you want to load Input LUTs Input LUTS can be loaded from local USB or the network resources Input LUTs may be copied to the system local resource via Windows SMB file sharing ftp or web access Input LUT 1 amp 2 Accesses the Input LUT menu for Inputs 1 amp 2 Input LUT 3 amp 4 Accesses the Input Lut Menu for Inputs 3 amp 4 File Management Delete and rename locally stored Input LUTs Cinemage User Manual Version 2 1 65 Input LUT 1 amp 2 Note When Cinemage is in Dual Link Mode Inputs 1 amp 2 become linked as do Inputs 3 amp 4 and Outputs 1 amp 2 allowing for only 2 Input LUTs to be applied as opposed to 4 in Single Link Mode Input LUT 1 amp 2 menu allows you to browse and apply a separate input LUT to input 1 and input 2 individually in single link mode and adjust the di
51. e is set for Single Line choose the line from either field 1 or field 2 to be displayed in the waveform NOTE The Waveform and Vectorscope will analyze by default the raw data of the video input routed to the display The recommended way analyze video data that has been corrected by the Input Range control and Input LUTs is to route the source through the splitscreen generator either in a split with your SDI Input as one source and the Reclocked version of the same input as the other source for a side by side analysis or with your SDI input as Splitscreen source 1 and the split turned off to view only your adjusted video signal Cinemage User Manual Version 2 1 80 Chapter 24 Analyse Waveform Setup OPTION The menu items in this manual will vary depending on the waveform option enabled on your system Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate to the Waveform Vectorscope menus select Analyse from the main menu The following menu will be displayed Analyse Menu Back Pixel Data Analysis Waveform Vectorscope Measure Display Output Gamut Violation Setup Input Status t From the Analyse Menu select Waveform Vectorscope The following menu will be displayed Analyse Waveform Vectorscope Back Waveform Vectorscope Waveform Wave Mode Line Mode Selected Line Vectorscope Off Full Field Field 1 Hold amp Release for Waveform Setup Source SDI 1 Press and hold the Wav
52. e the unit Password storage is in clear text by design Allowing users to edit the preferences file on their local computer copied to a USB key edited on a Mac or PC then reloaded into the Cinemage system Preferences are loaded into the system when upon power up and when a user clones a USB key to the system They are re written when shutting down the system and when cloning the system to a USB key Manage Preferences The Manage Preferences menu allows you to reset the local preference file as well as copy it to and from a USB datakey From the Preset Preferences Setup menu select Manage Preferences System Setup Preset Preferences Setup Menu Manage Preferences Manage Presets Save Current As Startup Settings Clear Startup Settings Press to set current state as startup Press to erase startup settings t You will get the following Manage Preferences menu System Setup Preset Preferences Setup Menu Manage Preferences 1 Back Reset Preferences to Load Preferences Save Preferences to USB Reload Preferences MORE Default from USB Reset Preferences to Defaults Resets preferences back to factory defaults Removes any customer specific settings Load Preferences from USB Loads Preference file from the USB data key to the system Save Preferences to USB Saves Preference file from the system to the USB data key Reload Preferences Reloads an edited preferences file Cinemage User
53. eeeeeeseeeeeessseeeeeeeessaaoes 29 Measure A RR aua n aua E NA HE RT 40 Steps to calibrate your display eeeeeeeeeereeeeeeeee 41 Chapter 7 Preset Preferences Setup ee eere ee eere e e eee eese snos e eese eetooes 42 Introduction to Presets and Preferences 42 Manage Preferences eeccceceeseeeeeeeeeeeeeeeeeeeeseeeneeeeeeeeeeeeeseeeneeeeeeeeenees 43 Manage Presets sentencie nnnc cr ia saias aires 45 Startup Settings c 0 0 00 aian 45 Chapter 8 USB Dat key Setup sisissesescocesceciecessdssecessesdessssceecedenessncesavsceccexvedocsesnoeeee 46 Cinemage User Manual Version 2 1 4 Format and Prepare USB 1 erre era rero are e ki 46 Clone System To From USB enean santo ra nu onn nonas nenn 46 USB TG CODY aede aiuto ibn ob b b bli khi nd 47 Setup Lockout with USB Key ceres 47 Updates ocnaensexinexa nena nai ined nani cud senda enne ean enano eon a enne eoo e e 47 USB File Copy MernU icon rne rone nro rue cnr nde cia 47 Updates Menu uius iin ace Avia e adve De uiui een 47 WED FTP Setuboisauo ma biais bbs biz iiie bit PIRES DSR PR 49 Remote File Setup 50 File Sharing IPRERPRERFRERURERERERERERPRERFEFRFRERERERPREEFRFRFDERFREREDERERERFPERFEFRERERERERFEERFEFFERFRER N 51 Wired Wireless Setup uunnnssssannnn
54. eform button to enter the Waveform Setup menu The following menu will be displayed Analyse Waveform Vectorscope Waveform Setup Waveform Mode Waveform Graticule H Magnification V Magnification Waveform Display Start of Analysed Area 1X 1X YCbCr Parade Full Options Back Returns to the Waveform Vectorscope Menu Waveform Mode Select the type of waveform display Choices are YCbCr Parade Y Cb Cr YCbCr Stacked RGB Parade R G B and RGB Stacked Cinemage User Manual Version 2 1 81 Waveform Graticule Select the type of Graticule for the waveform Choices are SMPTE Standard SMPTE graticule mapping 0 to a black data value of 16 for 8 bit data or 64 for 10 bit data and 100 to a white data value of 240 for 8 bit or 940 for 10 bit Use this when your video setup is in YCbCr mode with undershoot and overshoot limited Full Use this graticule in RGB mode and all YCbCr modes other than YCbCr mode with undershoot and overshoot limited H Magnification Provides a 2x 5x or 10x magnification of the time base on the waveform monitor display Use the Trackball horizontal movement to control which part of the waveform trace is displayed within the graticule V Magnification Provides a 2x or 4x magnification of the amplitude on the waveform monitor display Use the Trackball vertical movement to control which part of the waveform trace is displayed within the graticule Display Options Presents a menu allow
55. er of the display If you are using the EyeOne Display 2 place Cinemage User Manual Version 2 1 97 the probe on a flat black surface the top of the monitor works well then press press to calibrate probe When finished place the probe on the center of the display Press the Set Flat Field button until 10096 White is displayed Back xy Y X Y Y Select Display LUT Video Source Set Flat assi LE Field t Adjust the backlight to a comfortable setting for your ambient environment using the trackball Press the Read CIE xyY button Target x 314 y 345 x 314 y 345 Y 115Cd X 314 Y 345 Y 115 Cd Back xy Y LAAI Select Display LUT Video Source Set Flat Becht Bine Field Target x 314 y 345 x 314 y 345 Y 115Cd X 314 Y 345 Y 115 Cd t Read the Y result under CIE xyY and adjust the backlight either up or down until the desired luminance output is reached pressing the Read CIE xyY button to display new readings Once desired luminance is reached press the Back button to return to Display Setup menu Back xy Y LAAI Select Display LUT Video Source Set Flat Estr Biss Field Target x 314 y 345 x 314 y 345 Y 115Cd X 314 Y 345 Y 115 Cd t Select Auto Calibrate Auto Calibrate Manual Select Calibration Blue Only Measure Backlight Brightness Calibration t Check the results against the target located in the menu bar Back Auto Calibrate Manual Select Blue Only Mode Measure B
56. eset Calibration to Save Calibration Now Low Calibration Points Adjustments Overwrite Back Returns you to Manual Calibration menu 1 Adjust High Mid low Accesses the menu allowing you to adjust the x y Y R G and B values of the points along gamma curve Adjustments are made to the gamma curve sections divided into low 1 3 closest to black mid and high 1 3 closest to white Adjust Detailed Calibration Points Cinemage User Manual Version 2 1 35 Accesses the menu to make x y Y R G and B values to each of the 17 points along the gamma curve that Cinemage identifies for profiling the monitor Reset Adjustments Resets all of the calibration changes that you have made to the monitor in the Manual Calibration menu Changes made to the calibration profiles will have to be reset using this button as they will not be reset using the Reset menu found in the Setup menu Calibration to Overwrite Selects from one of the 5 custom calibration profiles or from the user definable REC 709 DCI or Linear profiles to overwrite with your manual adjustments Save Calibration Now Saves your manual changes to the calibration profile that you have elected to overwrite Display Setup Manual Calibration Menu 2 Back Adjust High Mid Adjust Detailed Reset Calibration To Save Calibration Now Low Calibration Points Adjustments Overwrite Pressing the Adjust High Mid Low will give you the following menu
57. ess allows for a greatly expedited workflow that is accessible on any Cinemage unit provided that unit contains the options included in you preset Press to lockout menus Cloning to from a USB key A quick and easy way to save all of your preferences and presets together to from a USB is to perform a clone This will save all of the information on the machine to the USB key including 1 Stills 2 LUTs 3 Presets 4 Preferences To perform a system clone enter the Setup menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls t Then enter the Network USB Datakey Setup menu Presets Press to lockout menus Back Video Setup Display Setup Preset Preferences Network USB Reset Setup Setup t Then enter the USB Datakey Setup menu Web FTP Setup Remote File Setup File Sharing Setup Wireless Setup USB Datakey Setup Cinemage User Manual Version 2 1 90 Once you have entered the USB Datakey Setup menu you will be able to save load your cloned system setup allowing for easy access to your previous workflow settings To clone to the USB key simply insert the key into the USB port on the front of the unit and press the Clone System to USB Key button Back Format amp Prepare Prepare USB Clone System to Clone USB Datakey Updates USB Key DataKey USB Datakey to System t To recall your saved system clone from the USB key simply insert the key into the USB port on the front of t
58. ess to the menu buttons Access is re activated by pressing this button for 5 seconds then releasing the button Blackout amp Lockout Performs both a blackout and a lockout The menus can be re activated by pressing button number 6 far right button for five seconds then releasing Blackout Top Applies a solid black field to the upper segment of the display disabling the default luma ramp typically displayed Keyed Lockout Locks access to the menu buttons and writes an unlock code onto a USB data key inserted into the system Access is re activated by inserting the USB datakey into the USB slot and pressing this button System verifies the lockout code on the USB key and opens menu access Lockout does not stay in force through a system power off Cinemage User Manual Version 2 1 22 Section 2 Setting Up Your System Cinemage User Manual Version 2 1 23 Chapter 3 Setup Overview Setup Menus To access the Setup Menus select Setup Menus from the Main Menu Main Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Original Settings Press to lockout menus T Upon pressing the Setup Menus button you will get the following menu Setup Menus Back Unit Video amp Display Preset Preferences Setup Network USB Datakey Setup Resets Information Setup Back Returns to the Top Menu Unit Information Takes you to the Unit Information Menu Video amp Display Setup Takes you t
59. et can be renamed in the Manage Presets menu Defaults Restores the system to the settings you had before you selected a Preset This would include any setup changes made from the time of power up Original Settings This restores the system to the settings loaded at the time of power up Power up settings are settings saved from the previous power down Preset 0 Selects the first of the user defined presets More Presets Moves forward to the next Presets menu Cinemage User Manual Version 2 1 18 Operator Menus Stills Operator Menus Stills Select Still gt _Operators Menu Still 1 Still 2 Still 3 Still 4 More Stills EM By using the trackball in the Operator Menus you can navigate to the Stills menus Each Stills menu page contains 5 Stills There are 20 Stills available in the system Use the trackball to advance the Operators Menus the next Stills page The Operators Menu returns you to the Operators Menu Operator Menus 3D LUTs Operator Menus 3D LUTs Select 3D LUT gt Operators Menu Reset 3D LUT 1 3DLUT2 3D LUT3 More 3d LUTs sd LUT 1 By using the trackball in the Operator Menus you can navigate to the 3D LUTs menus Each 3D LUT menu page contains 5 3D LUTs There are 20 3D LUTs available in the system Use the trackball to advance the Operators Menus the next 3D LUTs page The Operators Menu returns you to the Operators Menu System Menus To access the System Menus select System Menus
60. four Reclocked SDI sources will route the raw data feed from that input to the output unaltered by the input LUT s or Color Space Converter Dual Link Mode OPTION This menu toggles the Dual Link Mode between 4 2 2 YCbCr Single Link 4 4 4 RGB Dual Link and 4 4 4 YCbCr Dual Link Note When Dual Link is turn on input 1 amp 2 and 3 amp 4 are linked together as well as video out 1 amp 2 NOTES It is possible to create circular routing that would generate feedback An example would be routing the framestore as a source to the Cinemage User Manual Version 2 1 57 3D LUT and the 3D LUT output to the framestore It should also be noted that because Quad Split utilizes the resources of the Framestore it is not possible to output the Framestore from either of the HD SDI outputs while viewing Quad Split on the display However viewing Quad Split on the display is the only way to output the Quad Split through either of the HD SDI outputs Note that in most cases dual link video is full range NOT SMPTE range The input range is controlled in the Video Setup menu with the Input Limiting Mode In most cases for dual link this should be set to FULL RANGE Chapter 12 Process Framestore OPTION The framestore provides immediate access to up to 30 frames of stills You can capture any source into the framestore or load external still files from local network or the USB Datakey There are four menus for the framestore menu 1 menu2 st
61. ge A enabled Cage B enabled Cage A amp B enabled and Centered Crosswire To access the cage setup menu hold and release the Cages enabled button The following menu will be displayed Display Menu Cages Setup Cages Enabled E Mask Setup Cage A Cages Setup From the cage setup menu you may select to adjust cage A or cage B or to set masking around the cages Cinemage User Manual Version 2 1 69 After selecting Cage A or Cage B the following menu will be displayed Display Menu Cages Setup Cage A Cage Enabled Cage Type Cage Scale Cage Position Cage Style On i 2 35 1 _ X 1920y 1200 Use Trackball _ _ White Cage Type Select from standard cages of 1 33 1 1 77 1 1 86 1 2 35 1 and safe title and safe action for 1 33 and 1 77 or you may set a custom cage of any aspect ratio Cage Scale Scale the selected cage Use trackball to adjust Size is shown as number of pixels horizontally x and number of pixels vertically y Cage Position Position the selected cage on the display The x y indicator references the first pixel of the cage in the upper left hand corner Cage Style Choose between a cage with a white border or a cage with an inverted luminance border Mask Setup From the cage setup menu you may select to Mask Setup to set masking around the cages After selecting Mask setup from the Mask Setup Menu the following menu will be displayed Display Menu Mask Setup Cage or Mask
62. he unit and press the Clone USB Key to System button Back Format amp Prepare Prepare USB Clone System to Clone USB Datakey Updates USB Key DataKey USB Datakey to System t One important point to note is that your USB key will have to be prepared prior to saving any information from the Cinemage unit to the datakey so that the USB key will have the Cine tal file structure and format placed on the key allowing the system to recognize the formatting and to save and retrieve files To prepare the USB key inset the key into the USB port on the front of the unit and press either the Format and Prepare USB Key button or the Prepare USB Key button Format amp Prepare Prepare USB Clone System to Clone USB Datakey Updates USB Key DataKey USB Datakey to System hb q Please be advised that the Format and Prepare USB Key button will erase any information on the USB Key before adding the Cine tal file structure and format The Prepare USB Key button will simply add the Cine tal file structure and format to the key leaving any other information stored on the key in tact Cinemage User Manual Version 2 1 91 Software Updates Upgrades Cine tal is continually working towards product improvements to aid in the functionality of our monitors in your production process As such software updates will be released to improve the way Cinemage functions In addition to these software updates you have the ability to purchase or operate on a
63. ilable for the Cinemage line of products Trademarks All brand and product names mentioned herein are used for information purposes only and may be trademarks or registered trademarks of their respective companies Cinemage User s Guide Copyright 2005 Cine tal Systems LLC All Rights Reserved Reproduction adaptation or translation of this document without prior permission is prohibited except as allowed under copyright laws Printed in the United States Note The information in this document is subject to change without notice or obligation Cine tal Systems LLC REVA Cinemage User Manual Version 2 1 3 Table of Contents Official Notices 5 Ii dccacec ads ee ll 7 Limitation of Liability cT C 7 Software License Agreement sessseessocesocessoccssccssocessocesocecoocesoessoecesocesocesoocesseessecssoses 7 Cine tal Hardware Warranty eesseecsocccoossooessoeocsooscoceccoseccocesoecsocosssoccossccoeesooesocossssee 8 Cine tal Software Warranty sci cesccsectssccesescnacsevendccvoccensconsevnasvecenscesessoscncasendnvysnncbsndeene 9 Section 1 Getting Started sea 11 Chapter 1 Introduction aaa dita aea cance tvscsvcaevassnsandsnpeevevecsvecueceppeneeenines 11 ME OA ls eec 11 Howto use this guide nase 11 Block Diadf ai cinia a EU E dd anais 13 xir d r1 c 14 Rear Panel t E 14 Power Requirements 40 00 0 00a 14 User Serviceable Parts a a SFr aa ERR eu EOS a END ARRA 14
64. ill file management and setup Note You must have a reference sync input either from a video input or the analog reference input to use the framestore Framestore Menu 1 Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate the framestore menus select Process from the main menu the following menu will be displayed Process Menu Back Framestore Colourgrade Input LUTS Pan and Zoom t Select Framestore from the Process menu and you will get the following menu Process Menu Framestore Framestore Menu 1 Back Framestore Mode Capture Frame Browse Files Load File Now Current Framesiorg Live File_name dpx File_name dpx Hold amp Release for Framestore Setup Back Framestore Setup Press once to return to the Process Menu Press and hold for 2 seconds then release to go to the Framestore Setup Menu Cinemage User Manual Version 2 1 58 Framestore Mode Switches the framestore mode from displaying the video source routed to the framestore input Live Mode to displaying the output of the framestore listed under Current Framestore Still Mode The Current framestore is selected by the trackball Capture Press once to capture the framestore source to the current framestore Browse Files Browses through still files located at the selected file location File location include local network and USB Datakey File formats supported include DPX JPG BMP TIFF and PNG Load File
65. im prefs xml XML Notepad File Edit view Insert Tools Help Wa FileSharingEnablec Nw wirelessenabed false Cd Wa staticIPEnabled fase H E static ip filo static gateway EM static subnet file locations stills id EM connection info s H E file locations luts H E connection info lt LOCAL CI fie locations ver DD v li For Help press F1 Now insert the proper username path and password Note that the password is stored in cleartext by design so that this 1s possible Text connection info stills xsi type al connect data xmlns al http schemas microsoft com clr nsassem Philo PhiloController 2C 20Vers ion 3D1 0 2168 38160 2C 20Culture 3Dneutral 2C 20PublicKeyToken 3Dnull gt lt username id ref 14 gt EXAMPLEDOMAIN JSMITH lt username gt lt path id ref 15 gt BIGSERVER IMAGES lt path gt lt password id ref 16 gt asdjkfao H lt password gt lt connection_info_stills gt XML Editor Cinemage User Manual Version 2 1 86 Step 3 5 6 T 8 9 10 11 i4 prefs xml XML Notepad File Edit View Insert Tools Help Dell e e a Pisa 9 id connection info stills xsitype xmins al EM username 3 path CJ password file locations luts input connection info luts input E file_locations_waveforms PO lt p For Help press F1 Copy the preferences back to the Cinem ge Insert a USB memory key into the Cinem ge
66. ing control of the refresh rate of the waveform trace decay and the brightness of the trace gain Start of Analysed Area The first number indicates the pixel that is the start of the waveform trace 40 to 1920 The second number indicates the vertical offset from the center graticule line in digital scale 512 Cinemage User Manual Version 2 1 82 Chapter 25 Analyse Vectorscope Setup OPTION Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate to the Waveform Vectorscope menus select Analyse from the main menu The following menu will be displayed Analyse Menu Pixel Data Analysis Waveform Vectorscope Measure Display Output Gamut Violation Setup Input Status From the Analyse Menu select Waveform Vectorscope The following menu will be displayed Analyse Waveform Vectorscope Display Source Waveform Vectorscope YCbCr Range Mode Field Line Selected Line SDI 1 YCbCr Parade Off Undershoot Clipped Line Field2 514 eform Setup Hold amp Release for Wave Hold amp Release for Waveform Setup Press and hold the Vectorscope button to enter the Vectorscope Setup menu The following menu will be displayed Analyse Waveform Vectorscope Vectorscope Setup Vectorscope Mode Vectorscope Graticule Vectorscope Display Decay Vectorscope Display Gain On Fast 6 100 Back Returns to the Waveform Vectorscope Menu Vectorscope Mode Select to turn on and displ
67. is Magnification options are 1x 2x 4x 8x and 16x Freeze Frame Freezes the video on the display to allow for in depth analysis of a particular portion of the video feed More Advances to the next menu Pan Using the trackball you are able to manipulate the portion of the magnified video that is being displayed Cinemage User Manual Version 2 1 67 Process Menu Pan and Zoom 1 Magnification Horizontal Vertical Freeze Frame Magnification Magnification Pressing the More button will give the following menu Process Menu Pan and Zoom 1 Source Crosswire Browse Stills Load Still Now Display RGB Value Source Changes the input or internal source routed to the display that is to be magnified for closer inspection Crosswire Turns on a cross hair that can be positioned by the trackball The cross hair determines the pixel being read Browse Stills Browses through still files located at the selected file location File location include local network and USB Datakey File formats supported include DPX JPG BMP TIFF and PNG Load Still Now Loads the file selected in the Browse Files Button Display RGB Value Gives the RGB values of the pixel highlighted with the Pixel Data Analysis Crosswire NOTES The magnification and panning of the display will be affected in the Waveform Monitor and Vectorscope as well As you zoom into a particular portion of the display the Waveform Monitor and Vector
68. is in dual link RGB mode Main Menu Cinemage 2142 Route Process Display Analyse To navigate to the Pixel Data Analysis menus select Analyse from the main menu The following menu will be displayed Analyse Menu Pixel Data Analysis Waveform Vectorscope Measure Display Output Gamut Violation Setup Input Status t Pixel Data Analysis From the Analyse Menu the select Pixel Data Analysis The following menu will be displayed Analyse Pixel Data Analysis Back Pixel Analysis Pan and Zoom Display RGB Pixel Value Input Pixel Data More Pixel to read Crosswire R 256 G 230 B 110 SDI 1 Y 654 Cb 545 Cr 654 1034 539 On Back Returns to the Analyse Menu Pixel Analysis Crosshair Turns on a cross hair that can be positioned by the trackball The cross hair determines the pixel being read Pan and Zoom See Pan and Zoom Chapter 19 Display RGB Pixel Value The Cinemage system must convert all incoming video to 8 bit RGB for the display This conversion is only for the display and does not affect the general video path input to output The Display RGB Pixel value will provide you with the result of that conversion at the point indicated by pixel analysis crosshair and the trackball Cinemage User Manual Version 2 1 76 Input Pixel Data Displays the pixel value of the source at the point indicated by pixel analysis crosshair and the trackball More Goes to the 2 page of the Pixel Data Analysis menu Analy
69. l Settings Press to lockout menus T Upon pressing the Setup Menus button you will get the following menu Setup Menus Back Unit Video amp Display Preset Preferences Setup Network USB Datakey Setup Resets Information Setup Back Returns to the Main Menu Unit Information The Unit Information navigates the user to the menus providing information on the unit including software version IP Address MAC Address TCP IP machine name software options installed diagnostics network status and software update and restore menus Video amp Display Setup Takes you to the Video amp Display Setup Menu Preset Preferences Setup Takes you to the Preset and Preferences Setup Menu Network USB Setup Takes you to the Network and USB Data Setup Menu Resets Takes you to the Resets Menu Cinemage User Manual Version 2 1 21 Lockout Menu To access the Lockout Menu the user must press the Top Menu s first button Model Number Main Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets riginal Settings Press to lockout menus T Upon pressing the system model number button you will get the following menu Cinemage 2142 Blackout Lockout Blackout and Blackout Top Keyed Lockout Lockout Back Returns you to the Main Menu Blackout Removes the upper reference bar and menus The menus can be re activated by pressing any button Lockout Locks acc
70. led Software exclusively on hardware on which Cine tal Systems LLC has installed the Software or on hardware on which Cine tal Systems LLC has authorized it to be installed Such Software may only be enabled modified or updated by Cine tal Systems LLC or its authorized agent Cine tal Systems LLC and its licensors retain the right title and interest in and to all Software Title to the media on which the Software is delivered is transferred to the Customer Restrictions The Software is copyrighted and may contain material that is protected by patent trade secret or other laws pertaining to proprietary rights You may not copy the Software except that you may make a single copy for archival purposes You may not modify the Software or permit or assist any third party in doing so You may not decompile reverse engineer disassemble or otherwise reduce the Software to source code or other human readable form or attempt or permit any third party to do so Any violation of this Software license shall be a material breach and shall immediately entitle Cine tal Systems LLC to exercise any remedy that may exist at law or in equity Copyright All title and copyrights in the Software and any copies thereof and the accompanying printed materials are owned by Cine tal Systems LLC All rights not specifically granted under this Software License Agreement are reserved by Cine tal Systems LLC Cinemage User Manual Version 2 1 7 Cine tal Hardware Warra
71. locations local memory a USB Cinemage User Manual Version 2 1 88 datakey or a remote server location To change the location the Presets are saved to recalled from you must enter the Setup Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Press to lockout menus t Then enter the Presets Preferences Setup Menu Back Video Setup Display Setup Preset Preferences Network USB Reset Setup Setup t Then enter the Manage Presets Menu Back Manage Preferences Manage Presets t Then toggle the Location Back Choose Preset Location Save Preset as New Overwrite Existing Delete or Rename 0 Local 1 Preset Preset t Once the location is set you may save your settings off to that location by pressing the Save Preset as New button Back Choose Preset Location Save Preset as New Overwrite Existing Delete or Rename 0 Local 1 Preset Preset t And the Preset can be renamed using the trackball to operate the character generator in the Delete or Rename Preset menu Back Choose Preset Location Save Preset as New Overwrite Existing Delete or Rename 0 Local 1 Preset Preset t Cinemage User Manual Version 2 1 8 o While this may be a mildly involved process to save all of your workflow settings initially once they are saved you have one button access to them from the Main System menu Cinemage 2142 Process Display Analyse Select Preset Original Settings t This one button acc
72. nates Select Calibration Selects one of the available stored calibrations Measure Now Provides directions and starts measurements Note When using the GretagMacbeth EyeOne Design you must calibrate the EyeOne design probe on the white tile provided with the probe If you are using the GretagMacbeth EyeOne Display2 Probe you may skip this step Set Flat Field Sets the display to a flat field of black 17 progressively brighter shades of grey 100 white 100 red 100 green and 100 blue for display measurement Backlight Brightness Sets the brightness of the backlight This should be done first to set the total Luminance output desired for your calibration The brightness control has 1 168 steps for accurate control of the backlight The Measured output will be the Y result read back after calibration is completed You may use the Measure menu located in the display setup menu to pre set the backlight before you do your first calibration Cinemage User Manual Version 2 1 40 Steps to calibrate your display Option Before navigating to the Display Setup menu plug the GretagMacbeth GMB calibration probe into the USB port If the probe is not plugged in before navigating to this menu the monitor will not be able to see the probe until the unit is restarted with the probe attached ak WON gt 6 7 8 From the main menu press select Setup Menus Select Video amp Display Setup Select Display Calibr
73. nce __Update Licence Key E Lock Code Update From USB Key Installs software updates from a USB datakey Cinemage User Manual Version 2 1 47 Generate Licence Lock Code Generates a lock code for use with software updates obtained from Cine tal Update Licence When a USB key with the lock and unlock code for a software upgrade is inserted this button will unlock the software based upgrade See Software Upgrade in Appendix A Note itis possible although rare for an update to fail due to an error in loading the FPGAs This will result in some unpredictable behavior to be seen on the display If you believe that an update has failed please consult the readme file that corresponds with that particular update All relevant readme files can be found at www cine tal com downloads htm Cinemage User Manual Version 2 1 48 Chapter 9 Network Setup The Network Setup Menu provides setup and control functions for controlling WEB and FTP services setting up a network file server location to store stills LUTs waveforms and presets This menu also sets up the Cinemage system to share its locally stored information out to the network From the System Setup menu select Network USB Datakey Setup System Setup Menu Back Video Setup Display Setup Preset Preferences Setup Network USB Setup You will get the following menus System Setup Network USB Datakey Setup Menu WEB FTP Setup Remote File Setup File
74. nd you will get the following Video amp Display Setup menu System Setup Menu Video amp Display Setup Back Video Setup Display Calibration Video Setup Takes you to the Video Setup Menu Display Calibration Takes you to the Display Calibration Menu System Setup Menu Video amp Display Setup Back Video Setup Display Calibration T From the Video amp Display Setup Menu selecting Video Setup will display the following menu System Setup Video amp Display Setup Video Setup Menu Back Dual Link Mode Sync Source Current Format SDI Timing Input Limiting On SDI 1080 24PsF Input 1 mode Hold and Release for setup Dual Link Option If the system is a model 2142 or a model 2122 you will have the dual link option installed By setting Dual Link Mode to on the inputs and outputs of the monitor will be configured as 2 dual link inputs and 1 dual link output Dual Link mode will not turn on automatically when a dual link signal is applied You must manually select between 4 4 4 RGB Dual Link 4 4 4 YCbCr Dual Link or 4 2 2 YCbCr Single Link mode Cinemage User Manual Version 2 1 27 Sync Source This function sets the sync master for the entire unit You may choose between Free run Analog or SDI If SDI is selected the SDI Timing Master Menu will appear in the menu bar The user can then select from any of the HD SDI inputs or Automatic In the Automatic mode Sync will follow whatever valid sync is routed
75. nerator Enters the Flat Field Generator Menu which allows you to manipulate the R G and B color components of any of the Flat Field Test Patterns Full Screen Generator Using the trackball you can cycle through available test patterns and apply them to the full display The included Test Patterns are 1 8 GREY 100 FULL RANGE BARS 75 FULL RANGE BARS 100 SMPTE RANGE BARS 75 SMPTE RANGE BARS UMA FULL RANGE RAMP ED RAMP REEN RAMP LUE RAMP UMA LINEAR RAMP E R oco Oy O1 4S CO P2 E o IS 014 CO OIL CO D LINEAR RAMP EEN LINEAR RAMP UE LINEAR RAMP LUE YELLOW RAMP RED CYAN RAMP COMBINED COLOR RAMPS 30 MHZ FREQUENCY SWEEP Sy 10 15 20 25 30 MAG MULTIBURST 19 PLUGE PATTERN 20 LUMA PULSE amp BAR 21 LUMA TEN STEP 22 LINE END MARKER PATTERN 23 BLACK TEST BARS 24 SMPTE RANGE BLACK TEST BARS 25 100 RED 26 100 GREEN 27 100 BLUE 28 100 WHITE 29 BLACK WWODAFWAD Note The test patterns are all internal to the monitor and are thus not corrected by the input range control or the input LUT This means that the internal PLUGE cannot be used to test black levels use the pixel analysis tools to do this instead Cinemage User Manual Version 2 1 75 Chapter 21 Analyse Pixel Data Analysis OPTION Pixel data analysis provides a means of selecting any pixel on the displayed source getting the data values for Y Cb Cr or R G B if the system
76. ng EDID If you are using an operating system in your computer that allows manual settings for monitor support you should set them to Pixel Clk 154 V Active Lines 1200 H Active Pix 1920 V Blank 35 H Blank 160 V Sync Offset 3 H Sync Offset 48 V Sync Width 6 H Sync Width 32 V Image Size 324 H Image Size 519 V Border 0 H border 0 Min V Rate 56 Hz Min H Rate 30 KHz Max V Rate 76 Hz Max H Rate 81 KHz Max Pxl Clk 170 MHz Setting EDID Although it is not required to use the DVI input customers with Cinemage units shipped before December 1 2006 may want to setup the EDID on their systems Setting the EDID is accomplished with a field update kit available for loan from Cine tal The EDID update kit allows customers to set their EDID without returning the units to the factory The update kit includes a special DVI cable and WindowsXP based software System requirements are a WindowsXP based system with a standard RS232 Serial Port Customers may also return units to Cine tal for EDID settings Contact Cine tal Customer Service 01 317 576 0091 or support cine tal com to determine the best method for you lt lt END gt gt Cinemage User Manual Version 2 1 100
77. nty a Company warrants to the original purchaser of Equipment that for the Warranty Period as defined below the Equipment will be free from material defects in materials and workmanship The foregoing warranty is subject to the proper installation operation and maintenance of the Equipment in accordance with installation instructions and the operating manual supplied to Customer Warranty claims must be made by Customer in writing within sixty 60 days of the manifestation of a problem Company s sole obligation under the foregoing warranty is at Company s option to repair replace or correct any such defect that was present at the time of delivery or to remove the Equipment and to refund the purchase price to Customer b The Warranty Period begins on the date the Equipment is delivered and continues for 12 months c Any repairs under this warranty must be conducted by an authorized Company service representative at an authorized repair facility The customer is responsible for costs associated with shipping the equipment to and from an authorized repair facility d This warranty is for the hardware and hardware sub systems of the equipment and specifically excluded from the warranty is all software which is covered under the software warranty problems due to accidents misuse misapplication storage damage negligence or modification to the Equipment or its components e Company does not authorize any person or party to
78. nual Version 2 1 53 9 Verify that your router has assigned the system an IP address or that the static address you entered is accurate under IP address 10 Note the TCP IP Machine 11 From a Windows or Mac you may browse the network to find the Cinemage Monitor Cinemage uses a Universal Naming Convention based on the its TCP IP Machine Name Cinemage User Manual Version 2 1 54 Chapter 10 System Reset The Resets menu allows you to reset all system settings either to your power up original settings or to the factory original settings This will also provide a safe way to return to your last saved settings Each time you power the system down information is stored as the original settings Upon power up these settings are loaded into the system remembering the last state of the system settings Factory settings are the settings at the time the system ships from the factory Resetting to the factory settings will erase any sensitive network path user names or password information From the System Setup menu select Resets System Setup Unit Information Video amp Display Preset Preferences Setup Network USB Datakey Setup Resets System Setup Resets Back Reset to Defaults Factory Reset Are you sure Reset to Defaults Resets will reset all network and system setups to the last saved power up defaults Factory Reset Resets will reset all network and system setups to the factory settings erasing all network informa
79. nunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 52 Steps to connect Cinemage to a network router 53 Chapter 10 System Reset 44 eieeos nennen a tseaS ceed cenncavencey cdestsnsuexsnpnevatcusvenedeyherevenones 55 Reset to Defaite a 55 Factory Restinn a Aida 55 Section 3 Using Your SystemM esssesssssssececsssscceessooccessscoocesssseceesssscceesssso 56 Chapter 11 Routing escape Renee 57 Display SOUEFGB nee 57 DYI Input Fullmode nennen 57 VI QUI SOURCE cem S 57 VZ QUE SOUFGE DR C 57 Dual Link Mode cccun esu EReav avc cuu Dac DR Ex PX CT Y EDI D Re dU ava e Ru a DeC YO Reg insira Xe EC 57 Chapter 12 Process Eramestore oie ee nike el 58 Framestore Menu 1 u2 u a ete io par anknahanneinane 58 Framesiore Menu 2 on cca etra cora saran ev ers ona ci nda eranc rv o cr an ran qua x dra 0 CH ae ina a Ira ue Ya a quUE 59 Framestore Still File Management Menu ss 60 Framestores SClUP tina areais iara Opp o andas V an 61 Chapter 13 Process Colourgrade cscccssssssssssssssssssssssssssssscesssessssssssssessecssess 64 SO LU SOUICO iarciet haie T T eu etaa ie ceci E dc debo acia ban 64 DIS Play Source 2 nn een 64 Browse 3D LUTS eeeee e eee eeeeeeeee eene nennen nnn nanus aan nnne nana nna n n 64 Load LUT NOW rc 64 Chapter 14 Process Input LUT S
80. o make adjustments to in order modify the monitor s response curve Adjust R When selected this button allows you to use the trackball to the right of the monitor to adjust the red component of the monitor s response curve for the calibration point selected Adjust G When selected this button allows you to use the trackball to the right of the monitor to adjust the green component of the monitor s response curve for the calibration point selected Adjust B When selected this button allows you to use the trackball to the right of the monitor to adjust the blue component of the monitor s response curve for the point selected Cinemage User Manual Version 2 1 39 Measure Option This menu allows you to measure the response of the display System Setup Display Setup Menu Auto Calibrate Manual Select Blue Onle Mode Measure Backlight Brightness 20 Calibration Calibration Selecting Measure from the Display Setup Menu displays the following menu System Setup Display Setup Measure Menu Back xy Y X Y Y Select Calibration Video Source Set Flat Backlight Brightness 45 Field Target x 314 y 345 x 314 y 345 Y 115Cd X 314 Y 345 Y 115 Cd Back Returns you to the Display Setup Menu Displays target CIE x y measurements for rec 709 or D Cinema if selected as Display LUT X y Y Provides result of measurement in CIE x y Y coordinates X Y Y Provides result of measurement in CIE X Y Y coordi
81. o the Video amp Display Setup Menu Preset Preferences Setup Takes you to the Preset and Preferences Setup Menu Network USB Setup Takes you to the Network and USB Data Setup Menu Resets Takes you to the Resets Menu Cinemage User Manual Version 2 1 24 Chapter 4 Unit Information Menus To access the Unit Information Menus select Unit Information from the Setup Menus Unit Video amp Display Preset Preferences Setup Network USB Datakey Setup Information Setup Upon pressing the Unit Information button you will get the following menu Unit Information Menus 1 Unit Information IP Addresses MAC Addresses TCP IP Machine name Release 1 2 r3 192 168 1 123 00 04 5F 82 56 A3 Cinetal 316453 Back Returns to the Main Menu Unit Information Provides information on software and firmware versions I P Address The current I P address for the machine This may be either a static I P address or a DHCP Address see network setup for more information MAC Addresses Display the Mac address for the systems wired and wireless network interface Wireless networking is an option TCP IP Machine Name Provides the UNC designator for the machine on the network This is used to set a network path to the machine from a network workstation example cinetal 316012 More Takes you to Unit Information Menu 2 Cinemage User Manual Version 2 1 25 Unit Information Menus Options Diagnostics Netw
82. of the display Check the results and make adjustments to the backlight for Luminance level and Manual Calibration settings as needed and re calibrate until you have the desired results Calibration Complete Cinemage User Manual Version 2 1 41 Chapter 7 Preset Preferences Setup From the System Setup menu select Preset Preferences Setup System Setup Menu Unit Information Video amp Display Preset Network USB Setup Setup Preferences Setup You will get the following Preset Preferences Setup menus System Setup Preset Preferences Setup Menu Manage Preferences Manage Presets Save Current As Startup Settings Clear Startup Settings Press to set current state as startup Press to erase startup settings Introduction to Presets and Preferences The Cinemage stores user settings in two types of files Preferences constitute settings that are specific to a given machine and its network environment Some of these things such as selected network paths along with usernames and passwords might be sensitive Passwords are stored in clear text so it s good practice to reset see reset under System Setup Menu the preferences to clear any sensitive security information when necessary Here are some examples of things that are stored in preferences 1 Network logons paths and passwords for remote file access 2 FTP server settings whether the server is enabled and the current passw
83. ord 3 Web settings if the Web server is enabled 4 Storage information whether the system is set to use local remote or USB storage for stills and the various LUTs Presets files describe the way the system interacts with video and how it s used in the workflow Presets are loaded from the front panel at the top level menu when you press the button the preset file is loaded and the name of the file appears Here are some examples of things that are stored in a presets file 1 Cage Graticule size and position Video standard if not in automatic mode Heads up display settings Dual link mode vs Single link mode Routing Ore o Io Cinemage User Manual Version 2 1 42 Both files are standard XML and are user editable most simply by cloning the system to a USB key transferring the USB key to a standard computer Mac or PC editing the files then cloning the USB key back to the system See network USB key setup Note The Cinemage is an embedded device so that it cannot give the same kind of specific feedback regarding malformed XML that a desktop computer could give Malformed or invalid user edited XML may result in unpredictable behavior by the Cinemage unit For that reason Cine tal strongly suggests that you back up XML files before you attempt to edit them Cine tal does not have schema publicly available for these files at the current time so it encourages users to use the front panel or web controls to configur
84. ork Status Serial Number Secondary Inputs Enabled Working Set 29 970 432 00 Network Startup Complete 0604 316023 Back Returns to the Previous Menu Options Provides information on software options enabled Diagnostics For internal use only Network Status Displays status of network startup and acquisition Serial Number Displays System Serial Number More Takes you to Unit Information Menu 3 Unit Information Menus 3 Update From USB Cinetal Remote Control Insert USB Key with Update E Activate Now Back Returns to the Previous Menu Update From USB Updates to your system software can be downloaded from the Cine tal website and loaded on your USB datakey The update facility will only support one update at a time per key and the unit will display the name of the update to be loaded Use this button to run the update keeping your system up to date with the latest developments from Cine tal Cine tal Remote Control Need Cine tal technical support to remotely look at your system You will need to have your system on a public IP address outside of your firewall Call Cine tal technical support and we will log into your system remotely and see what we can do to help Cinemage User Manual Version 2 1 26 Chapter 5 Video amp Display Setup System Setup Menu Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup From the System Setup menu select Video amp Display Setup a
85. ously referenced Display Control Menu to make adjustments to the Gamma setting Brightness Contrast and Backlight controls Scaler and Deinterlacer Accesses the previously referenced Scaler and Deinterlacer menu for Image Scaling Motion Compensation and Single Field Mode For SD mode there is an addition of the option to show or hide the top six lines of the picture that is often used to hold time code or closed captioning information Cinemage User Manual Version 2 1 84 Appendix A USEFUL OPERATIONS Cine tal Cinemage Preferences Control Setting Remote File Locations The Cinemage features a remote file access capability that allows for storing and accessing media on remote file servers This requires that the remote server host a standard readable and writable SMB i e Samba or Windows file share Each type of file that can be accessed remotely still input LUT 3d LUT preset has a unique share associated with it Additionally there is a modal switch that allows the user to access these files either remotely from the share from a USB memory key attached to the monitor or on the monitor s local storage The advantages to using remote storage are that there are no storage restrictions beyond that on the server and that multiple monitors can use the same pool of presets images and LUTs Setting the remote file location can be done either from the front panel or through the preferences file prefs xml Using the front panel con
86. outer Before connecting the Cinemage unit to your network always check with your network administrator Determine if your network will require the Cinemage unit to be set for static IP or dynamic IP DHCP addressing Typically most networks use dynamic addressing Go to the Setup Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets Press to lockout menus t Then press the Network USB Datakey Setup button Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup Setup Setup t Then enter the Wired Wireless LAN Setup Menu WEB FTP Setup Remote File Setup File Sharing Setup Wired Wireless Setup USB Datakey Setup Under the Wired IP Mode set to either DHCP mode or Static IP whichever your networking requires Wireless Setup Wired IP Mode Wired Static IP Address Wired Static IP Subnet Mask Wired Static IP Garteway DHCP Mode 169 254 219 120 t If your system is set for DHCP skip this step If the system is set for Static IP setup the appropriate numbers for Wired Static IP address Subnet Mask and IP Gateway See Addendum A to edit this in the prefs xml file Wireless Setup Wired IP Mode Wired Static IP Address Wired Static IP Subnet Mask Wired Static IP Garteway DHCP Mode 169 254 219 120 T T t Cinemage User Manual Version 2 1 94 If you desire to restrict access to files stored on the Cinemage unit you may restrict access by se
87. per monitor setup by viewing the Color Bars in blue only mode Measure Enters the Measure menu System Setup Display Setup Menu Back Auto Calibrate Manual Select Calibration Blue Only Mode Calibration Measure Backlight Brightness 20 Selecting Manual Calibration from the Display Setup menu displays the following menu Display Setup Manual Calibration Menu 1 Calibration Set White Point Brightness Adjust x y R G B Options and Contrast Bias and Gain Back Returns you to the Display Setup Menu Calibration Options Takes you to the Calibration options menu Set White Point Allows you to choose from 12 user definable white point settings or select a custom white point as well as select the CIE Observer for each of these white points Brightness and Contrast Allows access to the Brightness and Contrast menu to adjust the digital emulation of the brightness and contrast of the display during manual calibration Adjust x y R G B Bias and Gain Accesses the menu to control the Display biases towards displaying R G and B values as well as the signal gain settings for the R G and B components of the signal More Advances to the second Manual Calibration menu Gamma Cinemage User Manual Version 2 1 30 Allows you to adjust the exponent used in the calculation of the gamma response curve of the monitor Display Setup Manual Calibration Menu 1 Calibration Set White Point Brightness
88. r On Off Cage A Enabled Hold amp Release for Cages Setup Hold amp Release for Setup Hold amp Release for Setup Split Screen Setup The Split Generator can be set for off horizontal split and horizontal split reverse To setup the split screen generator hold the button for 3 seconds and release Display Menu Split Screen Setup Select Split Split Screen Source 1 Split Screen Source 2 Display Source Split Marker Enabled Split Posten off off Split Screen Select Split Choose between Off H Split and H Split Reversed Split Screen Source 1 Select Source 1 for the split screen generator Split Screen Source 2 Cinemage User Manual Version 2 1 72 Select Source 2 for the split screen generator Display Source Select the display source If you want to view the split screen output in this menu make sure this is set for Split Screen Output Split Marker Enabled Enables a white border at the position of the split Split Position Adjusts the position the Splitscreen occurs at by rotating the trackball Chapter 19 Display Scaler amp Deinterlacer The Cinemage system uses a progressive scan LCD screen for the display When viewing interlaced material the process of converting from interlaced to progressive scan may cause unfavorable artifacts on moving edges of video content The Scaler and Deinterlacer menu allows access to several useful features for working with interlaced and SD video sources
89. r the VESA mount Power Requirements Cinemage runs on 100 to 240V AC at 50 or 60 hertz Nominal current is 2A OPTION If you have the DC input option installed you may run the system on 22 30v dc input Standard Anton Bauer 3 pin XLR connector is used Pin 1 is positive Pin 2 is ground and pin 3 is unused The mains disconnect for the Cinemage system is the power connector on the real panel of the system The input supply socket outlet should be located near the device and should be easily accessible User Serviceable Parts There are no user serviceable parts inside the Cinemage units Please refer all service to a Cine tal authorized technician Turning On The System To turn the system on simply depress the power toggle switch on the rear of the system Note To protect the system from erratic power outages the system requires a 10 second wait period between power down and immediate power up Cinemage User Manual Version 2 1 14 Chapter 2 Menu Overview In reading this section note that location of menu options may change over product revisions Furthermore available menu choices will vary depending on model number and installed options Functions that are dependent on installed options are marked as Option Main Menu After the system performs a power up self test the following menu will appear at the bottom of the display Main Menu Cinemage 2142 Operator Menus System Menus Setup Menus Display Controls Presets
90. rsion 2 1 10 Section 1 Getting Started Chapter 1 Introduction Welcome The Cinemage product family revolutionizes critical monitoring for digital cinema acquisition post production and DI by combining Cine tal s leading edge IDS Intelligent Display Server technology and calibrated full resolution LCD display Cinemage provides quantitative video analysis colour pre visualization video signal quality assurance real time collaboration between acquisition and post production and an integrated OmniTek Waveform Monitor and Vectorscope With Cinemage you can conduct both critical visual analysis and digital quantitative analysis of your HD SDI or HD SDI Dual Link signal in either YCbCr or RGB linear or logarithmic at 8 or 10 bits IDS Technology is a joint technology development between Cine tal and OmniTek IDS provides image processing signal routing frame stores and colour manipulation 3D LUT s and test and measurement all in a network appliance configuration Internal to IDS is a powerful image processor that generates real time data about the HD video stream This data is used to generate waveforms vectorscopes gamut information and status of the incoming video signal IDS also provides for display calibration and profiling as well as input signal colour grading for pre visualization All data and operations can be performed over a LAN WAN or wireless network with any web enabled device How to use this guide This
91. scope will give you readings of the video signal that is being displayed allowing for detailed analysis of particular portions of your video signal As the Pan and Zoom capability uses the framestore internally zooming on a split screen with only 1 side originating in the framestore will only zoom that side Zooming on a splitscreen wherein both sides originate in the framestore e g one on a frame and one on the same frame colour graded with the 3D LUT will maintain the current split position and let you do a left right compare on the zoomed image Cinemage User Manual Version 2 1 68 Chapter 16 Display Cages Graticules OPTION The Display menu provides access to the Cages Head Up Display Split Screen Pull Down and Pan Zoom functions Note You must have a reference sync input either from a video input or the analog reference input to use cages Cages Enabled The system has two cage generators that can be independently enabled Sized and positioned on the display Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate the cage menus select Display from the main menu the following menu will be displayed Display Menu Heads Up Display Split Screen Motion Compensation Test Pattern Generator On Off Cages Cage A Enabled Hold amp Release for Cages Setup Hold amp Release for Cages Setup Hold amp Release for Setup t The Cages enabled button cycles through Cages disabled Ca
92. se Pixel Data Analysis page 2 SDI SDI1 SDN SD Display RGB Pixel Pixel to read Y 0340 Cb 0525 Y 0340 Cb 0525 Y 0340 Cb 0525 Y 0340 Cb 0525 R 256 G 230 1034 539 Cr 0496 Cr 0496 Cr 0496 Cr 0496 B 110 SDI 1 Displays the pixel value on SDI 1 input at the location selected by the trackball SDI 2 Displays the pixel value on SDI 2 input at the location selected by the trackball SDI 3 Displays the pixel value on SDI 3 input at the location selected by the trackball SDI 4 Displays the pixel value on SDI 4 input at the location selected by the trackball Display Pixel Value Displays the pixel value of the Display at the location selected by the trackball Cinemage User Manual Version 2 1 77 Chapter 22 Analyse Pixel Analysis Pan and Zoom OPTION Pan and zoom provide a means to zoom into the display to look at pixel information up close Main Menu Cinemage 2142 Route Process Display Analyse Presets To navigate to the Pan and Zoom menus select Analyse from the main menu The following menu will be displayed Analyse Menu Pixel Data Analysis Waveform Vectorscope Measure Display Output Gamut Violation Setup Input Status t From the Analyse Menu the select Pixel Data Analysis The following menu will be displayed Analyse Pixel Data Analysis Pixel Analysis Pan and Zoom Display RGB Pixel Value Input Pixel Data Value Pixel to read Crosswire R 256 G 230 B 110 SDI 1
93. splay source Process Menu Input LUTs Input LUTs 1 amp 2 _ Load Input LUTA Reset Input Display Source Load Input Reset Input LUT2 LUT1 Lut2 Load Input LUT 1 Progresses through the Input LUT files from the source you designated in the main Input LUT menu and applies them to Input 1 Reset Input LUT 1 Removes the Input LUT from Input 1 Display Source Toggles the Video Source routed to the Display Load Input LUT 2 Progresses through the Input LUT files from the source you designated in the main Input LUT menu and applies them to Input 2 Reset Input LUT 2 Removes the Input LUT from Input 2 Input LUT 3 amp 4 Same menuing as Input LUT 1 amp 2 but pertains to Inputs 3 amp 4 Cinemage User Manual Version 2 1 66 Chapter 15 Process Pan and Zoom Process Menu Back Framestore Colourgrade Input LUTS Pan and Zoom t From the Process menu pressing the Pan and Zoom button will provide the following menu Process Menu Pan and Zoom 1 Magnification Horizontal Vertical Freeze Frame Magnification Magnification Magnification Controls the magnification of the entire display both horizontally and vertically Magnification options are 1x 2x 4x 8x and 16x Horizontal Magnification Controls the magnification of the display only along the horizontal axis Magnification options are 1x 2x 4x 8x and 16x Vertical Magnification Controls the magnification of the display only along the vertical ax
94. st G Adjust B ES R High Back Returns to the Adjust High Mid Low menu 1 Segment to Modify Selects either the High Mid or Low segment of the monitor s response curve to make adjustments to High refers to the 1 3 of the curve closest to white and Low refers to the 1 3 of the curve closest to black Adjust R When selected this button allows you to use the trackball to the right of the monitor to adjust the red component of the monitor s response curve for the segment selected Adjust G When selected this button allows you to use the trackball to the right of the monitor to adjust the green component of the monitor s response curve for the segment selected Cinemage User Manual Version 2 1 37 Adjust B When selected this button allows you to use the trackball to the right of the monitor to adjust the blue component of the monitor s response curve for the segment selected Display Setup Manual Calibration Menu 2 Back Adjust High Mid Adjust Detailed Reset Low Calibration Points Adjustments Calibration To Overwrite Save Calibration Now Pressing the Adjust Detailed Calibration Points will give you the following menu Display Setup Manual Calibration Menu 2 Adjust Detailed Calibration Points menu 1 Back Point to Modify Adjust x Adjust y Adjust Y Aue Back Takes you back to the Manual Calibration menu 2 Point to Modify Selects which of the 17 calibr
95. the framestore source to the current framestore and saves the image at the selected file location Each file may be given a pre fix followed be a four digit sequence number Sequential Capture Captures the framestore source to the current framestore and increments the current framestore by one Framestore Source Selects which source is routed to the framestore for capture Still File Management Navigates to the still file management menu Framestore Still File Management Menu The framestore still file management menu allows you to rename and delete files stored in the selected file location To navigate the framestore still file management menu select Still File Management from framestore menu 2 Process Menu Framestore Framestore Menu 2 Back Framestore Mode Capture amp Save Sequential Capture Framestore Still File Current Framestore View Source 1106_0004 dpx To Framestore Source Management LIA 53 Hold amp Release for Framestore h Setup The following menu will be displayed Process Menu Framestore Still File Management Menu Back File to Rename Delete Delete File Reset New Name Rename File Now Select Next Character Set2_1107_0012 dpx Set2_1107_0012 dpx Character c Hold amp Release for Framestore Setup Back Framestore Setup Press once to return to the Process Menu Press and hold for 2 seconds then release to go to the Framestore Setup Menu Cinemage User Manual Version 2 1 60
96. tion Cinemage User Manual Version 2 1 55 Section 3 Using Your System Cinemage User Manual Version 2 1 Chapter 11 Routing The routing menu allows you to route the input video input DVI framestore test patterns and 3D LUT output to the display or video outputs in the system System Menu Cinemage 2142 Route Process Display Analyse Select Preset l t From the system menu select Route The system will display the following menu Original Settings Hold and Release for setup Route Menu Display Source DVI INPUT V1 Out V2 Out Source Dual Link Mode Framestore FULLMODE SDI Input 1 SDI Input 4 4 2 2 YCbCR Single Link Display Source All four HD SDI inputs or 2 Dual Link inputs Quad Input Framestore Test Pattern and 3D LUT Output are routed to the display independent of the output DVI Input Fullmode Routes the DVI input to the display See FSB 061220 on page 99 for details V1 Out Source All four HD SDI inputs or 2 Dual Link inputs Framestore Test Pattern 3D LUT Output and DVI Input are routed to the output independent of the display Selecting one of the four Reclocked SDI sources will route the raw data feed from that input to the output unaltered by the input LUT s or Color Space Converter V2 Out Source All four HD SDI inputs or 2 Dual Link inputs Framestore Test Pattern 3D LUT Output and DVI Input are routed to the output independent of the display Selecting one of the
97. to the display Current Format Automatically detects and displays the input format to the monitor The Current Format Setup Menu Hold and release to access this menu provides the ability turn off the automatic detection mode and manually set the format when using the monitor to output test pattern signals or Framestore stills Auto Format can only be disabled if there is no video signal on the selected input to prevent viewing irregularities however if Auto Format is turned on with no video connected it will disable the Framestore until a valid video source is attached to the monitor SDI Timing When Sync Source is set to SDI you can choose which SDI input is the sync source Automatic mode automatically selects the timing from whatever source is routed to the display Input Limiting Mode Cinemage allows you to control how the information above and below peak white is displayed The following choices are available Full Range Provides viewing of the full legal value data range on the display This means that data values below legal black are visible and data values above legal white are visible Undershoot and overshoot clipped Clips values below legal black 16 for 8 bit data 64 for 10 bit data and clips values above legal white 240 for 8 bit data 960 for 10 bit data Undershoot clipped Clips values below legal black 16 for 8 bit data 64 for 10 bit data Cinemage User Manual Version 2 1 28 Chapter 6 Displa
98. trols where this file can be backed up to saved to or loaded from a USB memory key Here is the procedure for saving the current preferences file to a USB key manually adding the server information adding it to the monitor then connecting and verifying the connection Note that is only one technique for establishing the connection the alternative is to program it in from the front panel using the trackball Sel 1 Copy the preferences to a USB key Insert a USB memory key that s prepared for the Cinemage consult your manual for details 2 On the front panel from the first menu hold down the button that says hold and release for setup until it flashes 3 Select MANAGE PREFERENCES 4 Select SAVE PREFERENCES TO USB Step 2 Edit the preferences file 1 Move the USB key to a computer and open the file cinetal prefs xml in a text editor or xml editor 2 Find the connection info tag for the desired file type in this case we re changing the remote path for stills so that would be connection info stills Text connection info stills xsi type al connect data xmlns al http schemas microsoft com clr nsassem Philo PhiloController 2C 20Vers ion 3D1 0 2168 38160 2C 20Culture 3Dneutral 2C 20PublicKeyToken 3Dnull gt lt username xsi null 1 gt lt path xsi null 1 gt lt password xsi null 1 gt lt connection_info_luts_input gt Cinemage User Manual Version 2 1 85 XML Editor
99. tting a username and password for local network access If security is not a concern the default setting is a username of guest with no password To set the password press the Back button t Then press the File Sharing Setup button Back WEB FTP Setup Remote File Setup File Sharing Setup Wired Wireless Setup USB Datakey Setup t And setup the Username and Password Wireless Setup Wired IP Mode Wired Static IP Address Wired Static IP Subnet Mask Wired Static IP Garteway DHCP Mode 169 254 219 120 Fixed Network ID Fixed Sharing Sharing Password File Sharing Status Username Next you must reset the systems network status by toggling the File Sharing Status to Enabled then to Disabled and back again to Enabled Fixed Network ID Fixed Sharing Sharing Password File Sharing Status t Finally you must ensure that the router has assigned an address to the unit or that the static IP address is correct Hit the back button 3 times to return to the Main Menu Username Fixed Network ID Fixed Sharing Sharing Password File Sharing Status Username Too Then enter the Unit Information menu Back Unit Information Video and Presets and Network amp USB Resets Display Setup Preferences Setup Datakey Setup t Verify that that the router has assigned the system an IP address or that the static IP address is correct and note the TCP IP Machine Name Unit Information IP Addresses MAC Addresses
100. y Calibration From the System Setup menu select Video amp Display Setup System Setup Menu Back Unit Information Video amp Display Preset Preferences Network USB Reset Setup Setup Setup From the System Setup menu select Video amp Display Setup and you will get the following Video amp Display Setup menu System Setup Menu Video amp Display Setup Back Video Setup Display Calibration Selecting Display Calibration you will get the following Display Setup menus System Setup Video amp Display Setup Display Setup Menu Back Auto Calibrate Manual Select calibration Blue Only Mode Measure Backlight Brightness Calibration 20 Auto Calibrate Option Will start the automated process of re profiling the display by measuring the 17 calibration points and establishing the monitor s response curve Manual Calibration This menu allows you to manually adjust the display properties in a similar fashion to the conventional calibration found on CRT monitors Adjustments made in this menu can be saved by overwriting one of the existing display profiles For best results Manual Calibration should be performed after an Auto Calibration to achieve your optimal monitor response curve Select Calibration Cycles through the factory and user customized display profiles Blue Only Mode Cinemage User Manual Version 2 1 29 Causes the display to only output the Blue component of the video signal Can be used to ensure pro
101. y the trackball to the right of the monitor Contrast Selects the contrast setting for adjustment controlled by the trackball at the right of the monitor Special Note about Brightness and Contrast Cinemage emulates the contrast control of a CRT by manipulating the response of the LCD due to the nature of LCD technology contrast and brighness will start clipping very quickly when these controls are manipulated up In the general case you will get a better result by manipulation of the backlight and gamma than with the Brightness and Contrast as backlight and gamma are native LCD controls not emulated CRT controls Cinemage User Manual Version 2 1 32 Display Setup Manual Calibration Menu 1 Back Calibration Set White Point Brightness Adjust x y R G B and Contrast Bias and Gain T Pressing the Adjust x y R G B Bias and Gain will give you the following menu Options Display Setup Manual Calibration Menu 1 x y R G B Bias and Gain menu 1 Back Red Bias Green Bias Blue Bias More Flat Field Display pea Back Takes you back to the second Manual Calibration menu Red Bias Allows you to adjust the monitor s response curve upward for the Red component by using the trackball located at the right of the monitor Effects of the bias adjustment will be more visible towards the black end of the shading spectrum Green Bias Allows you adjust the monitor s response curve upwards for the Green component by

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents