RTM-ATCA7301 Installation and Use
Contents
1. Abbreviation Definition ETSI European Telecom Standards Institute FAE Field Application Engineer FCC Federal Communications Commission FRU Field Replaceable Unit GA General Availability HD Hard Disk H S Hot Swap IEC International Electric Code IPMC Intelligent Platform Management Interface Controller IPMI Intelligent Platform Management Interface LED Light Emitting Diode LUN Logical Unit Number MMC Mezzanine Management Controller NEBS Network Equipment Building System OOS Out Of Service OS Operating System PCB Printed Circuit Board PCI Peripheral Component Interconnect PICMG PCI Industrial Computer Manufacturers Group RoHS Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment RTM Rear Transition Module SELV Safety Extra Low Voltage SCSI Small Computer System Interface TPE Twisted Pair Ethernet UL Underwriters Laboratory USB Universal Serial Bus VCCI Voluntary Control Council for Interference 10 RTM ATCA7301 Installation and Use 6806800K95A About this Manual Conventions The following table describes the conventions used throughout this manual Notation Description 0x00000000 Typical notation for hexadecimal numbers digits are O through F for example used for addresses and offsets 0b0000 Same for binary numbers digits are 0 and 1 bold Used to2. 38 Table 4 1 IPMI Sensors Ihm 42 Table A 1 Emerson Publications seres eneren ea aan 43 Table 2 Related Specifications eee 43 RTM ATCA7301 Installation and Use 6806800K95A 5 List of Tables 6 RTM ATCA7301 Installation and Use 6806800K95A List of Figures Figure 1 1 Declaration of Conformity cece cece 15 Figure 2 1 Critical Temperature Spots on the RTM ATCA7301 HDD 21 Figure 3 1 Mechanical Layout estes ee 29 Figure 3 2 Face Plite mM 30 Figure 3 3 Face Plate with optional E1 T1 Connectors 31 Figure 3 4 USB Connector Pinout 32 Figure 3 5 Ethernet Connector Pinout 32 Figure 3 6 Serial Connector Pinout ee 33 Figure 3 7 SAS Connector PINOUT vu ne ech 33 Figure 3 8 Connector PiN Ut unse een 34 Figure 3 9 Location of Face Plate LEDS I 35 Figure 3 10 Location of SAS Connector nenn 37 Figure 4 1 Block Diagram for HD Variant cece eee eee nennen nennen 41 RTM ATCA7301 Installation and Use 6806800K95A 7 List of Figures 8 RTM ATCA7301 Installation and Use 6806800K95A About this Manual Overview of Contents This manual
3. Organization Document Title PCI SIG PICMG PCI Local Bus Specification Revision 2 2 PCI X Addendum to the PCI Local Bus Specification 1 0 PICMG 3 0 Revision 2 0 Advanced TCA Base Specification PICMG 3 1 Revision 1 0 Specification Ethernet Fiber Channel for AdvancedTCA Systems RTM ATCA7301 Installation and Use 6806800K95A Related Documentation 44 RTM ATCA7301 Installation and Use 6806800K95A Safety Notes EMC This section provides warnings that precede potentially dangerous procedures throughout this manual Instructions contained in the warnings must be followed during all phases of operation service and repair of this equipment You should also employ all other safety precautions necessary for the operation of the equipment in your operating environment Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment Emerson intends to provide all necessary information to install and handle the product in this manual Because of the complexity of this product and its various uses we do not guarantee that the given information is complete If you need additional information ask your Emerson representative The product has been designed to meet the standard industrial safety requirements It must not be used except in its specific area of office telecommunication industry and industrial control Only personnel
4. den EMV Richtlinien betrieben wird Verwenden Sie nur abgeschirmte Kabel zum Anschluss von Zusatzmodulen So ist sichergestellt dass sich die Aussendung von Hochfrequenzstrahlung im Rahmen der erlaubten Grenzwerte bewegt Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Betrieb Besch digung des Produktes Hohe Luftfeuchtigkeit und Kondensat auf der Oberfl che des Produktes k nnen zu Kurzschl ssen f hren Betreiben Sie das Produkt nur innerhalb der angegebenen Grenzwerte f r die relative Luftfeuchtigkeit und Temperatur Stellen Sie vor dem Einschalten des Stroms sicher dass sich auf dem Produkt kein Kondensat befindet 50 RTM ATCA7301 Installation and Use 6806800K95A Sicherheitshinweise berhitzung und Besch digung des Produktes Betreiben Sie das Produkt ohne Zwangsbel ftung kann das Produkt berhitzt und schlie lich besch digt werden Bevor Sie das Produkt betreiben m ssen Sie sicher stellen dass das Shelf ber eine Zwangsk hlung verf gt Installation Besch digung des Produktes und von Zusatzmodulen Fehlerhafte Installation von Zusatzmodulen kann zur Besch digung des Produktes und der Zusatzmodule f hren Lesen Sie daher vor der Installation von Zusatzmodulen die zugeh rige Dokumentation Besch digung von Schaltkreisen Elektrostatisc
5. Controls LEDs and Connectors The following figure shows the location of the SAS connector Figure 3 10 Location of SAS Connector SNE The SAS hard disk activity is shown via the HD LED at the RTM face plate RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors The following connector pinout gives information on which signal is assigned to which pin Table 3 3 SAS Connector Pinout Segment Pin Name Primary Signal S1 GROUND Primary Signal S2 RP Primary Signal S3 RP Primary Signal S4 GROUND Primary Signal S5 TP Primary Signal S6 TP Primary Signal S7 GROUND Secondary Signal S8 GROUND Secondary Signal S9 RS Secondary Signal S10 RS Secondary Signal S11 GROUND Secondary Signal S12 TS Secondary Signal 13 TS Secondary Signal S14 GROUND Power P1 V3P3 Power P2 V3P3 Power P3 V3P3 Power P4 GROUND Power P5 GROUND Power P6 GROUND Power P7 VP5 Power P8 VP5 Power P9 VP5 Power P10 GROUND Power P11 READY LED RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors Table 3 3 SAS Connector Pinout continued Segment Pin Name Power P12 GROUND Power P13 VP12 Power P14 VP12 Power P15 VP12 RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors RTM ATCA7301 Installation and
6. 13 MED ls 13 1 2 Standard Compliances u Glas sue eee ES PIE E E a ae 14 1 3 Mechanical Data RR RIRs n 16 1 4 Ordering Information ee ehe mere 16 2 Hardware Preparation and Installation eere 17 Ar OVENEW EEE a ea Da EE EEE 17 2 2 Unpacking and Inspecting the Module 0c cece eee eee eee eee ne 17 2 3 Environmental and Power Requirements cece cece cece 18 2 3 1 Environmental Requirements 0 0 cece ence eee enn 18 2 3 2 PowerRequlreiments cemere ke 22 2 4 Module Installation and Removal RR 22 241 Installing the RTM nn CIS S E 24 2 4 26 3 Controls LEDs and 29 3 1 cer ne ae ee acorn nee 29 3 2 ne 29 3 3 Face Plate Connectors and LEDs 30 3 3 1 Face Plate Connectors ccc cee ee 32 3 3 11 USB eoe ae net 32 3 3 1 2 Ethernet Connectors Rs 32 3 3 1 3 SerialConnector ccc ccc cece Rh ees 33 3 23 14 SAS Connectot tege beri ARGQ aaa 33 3 3 1
7. 5 u na 34 3 3 2 F cePlate LEDS cer ee eek 35 3 4 Onboard Connectors eee e ees 36 4 FunctionalDescription u nn 41 41 Overview er a 41 RTM ATCA7301 Installation and Use 6806800K95A 3 Contents AD BlOCK 41 43 Mezzanine Management ene e eee errre 42 A Related Documentation 0 43 A 1 Emerson Network Power Embedded Computing Documents 43 A 2 5 lt he meh 43 Safety ea ad nd e a paces haa eoa a cO p Ep erba hd dro E Pau 45 SicherhertshilWl else casa 08 a EUR IR RUN RN 49 Index ac een 55 4 RTM ATCA7301 Installation and Use 6806800K95A List of Tables Table 1 1 Standard Compliances niia iein biia iua iieii it 14 Table 1 2 Mechanical Data eeri ee ged tokens ede REY tenke ae 16 Table 1 3 Order Numbers Tm 16 Table 2 1 Environmental Requirements 19 Table 2 2 Critical Temperature Limits 22 3 1 Mapping E1 T1 Connectors AMC Ports on 7301 34 Table 3 2 Pl te LEDS nun die net en in 35 Table 3 3 SAS Connector Pinout enne
8. 9 5 5 3 3 1 4 SAS Connector The SAS connector can be used for connecting an external SAS disk or for creating a redundant RTM configuration The pin assignment of the SAS connectoris given in the following figure Figure3 7 5 5 Connector Pinout GND GND Rx 2 Rx 2 GND GND Rx 3 Rx 3 GND OND n c nn n C GND n c GND oo n c GND oo GND nu nn GND GND Tx 34 Tx 3 GND GND Tx 24 Tx 2 GND GND RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors 3 3 1 5 E1 T1 Connectors The pin assignment of the E1 T1 connectors is given in the following figure Figure3 8 1 Connector Pinout E1 T1 RX E1 T1 RX n c 1 E1 T1 TX E1 T1 E n c 8 N C N C ce o001 50N Table 3 1 Mapping E1 T1 Connectors AMC Ports on ATCA 7301 E1 T1 Connector AMC Port 1 AMC B4 Port 17 AMC B1 Port 17 AMC B4 Port 18 AMC B1 Port 18 AMC B4 Port 19 AMC B1 Port 19 AMC B4 Port 20 AMC B1 Port 20 O NSNIDJ BR RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors 3 3 2 Face Plate LEDs The following figure highlights the LEDs available on the face plate Figure 3 9 Location of Face Plate LEDs ETH2ACTILNK 0 HDD The following table describes the meaning of the LEDs Table 3 2
9. Use 6806800K95A Chapter 4 Functional Description 4 1 Overview This chapter describes e Block diagram e Mezzanine management controller 4 2 Block Diagram The following figure shows the main functional blocks ofthe RTM Figure 4 1 Block Diagram for HD Variant Face Plate ET 8x E1 T1 8x E1 T1 Backplane R XFMUR SAS LSI HE 7 Connector SAS1064E Ax PCIE 1 SAS 1 SAS Connector USB 1x USB MiniDB9 RS 232 Console Reset 12V 12C IPMB L RTM ATCA7301 Installation and Use 6806800K95A Functional Description 4 3 Mezzanine Management Controller The RTM provides a Mezzanine Management Controller MMC based on the Pigeon Point Systems PPS building block which is fully compliant to the IPMI V 2 0 standard The MMC is connected to the front blade s IPMC via IPMB L The MMC provides several status sensors that are accessible via IPMI These sensors are listed in the following table Table 4 1 IPMI Sensors Overview Sensor Name LUN Sensor Sensor Type 1 2V RTM 0x00 0 20 Voltage 12V HD RTM 0x00 0x33 Voltage 12V 0x00 0x34 Voltage 2 5V RTM 0x00 Ox2E Voltage 3 3V RTM 0x00 Ox2F Voltage 5 0V RTM 0x00 Ox2C Voltage temp in RTM 0x00 0x31 Temperature temp out RTM 0x00 0x30 Temperature BMC Watch RTM 0x00 0x32 Watchdog 2 Hotswap RTM 0x00 0x03 PICMG 3 0 FRU HotSwap For further details about these sensors as well as further IPMI relat
10. it according to your country s legislation The blade is thoroughly inspected before shipment If any damage occurred during v transportation or any items are missing please contact our customer s service immediately 2 3 Environmental and Power Requirements The following environmental and power requirements are applicable to the blade 2 3 1 Environmental Requirements You must make sure that the blade when operated in your particular system configuration meets the environmental requirements specified below Operating temperatures refer to the temperature of the air circulating around the blade and not to the component temperature NOTICE Product Damage Surface of the Product High humidity and condensation on the product surface causes short circuits Do not operate the product outside the specified environmental limits Make sure the product is completely dry and there is no moisture on any surface before applying power 18 RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation Table 2 1 Environmental Requirements Requirement Operating Non Operating Temperature 5 C 41 F to 40 C 104 F normal 40 C 40 F to 70 C 158 F may be operation according to NEBS Standard GR further limited by installed accessories 63 CORE 5 C 23 F to 55 C 131 F exceptional operation according to NEBS Standard GR 63 CORE T
11. the blue LED of the RTM is permanently ON A permanently switched ON LED indicates that the payload of the RTM has been powered down 3 Remove interface cables from face plate connectors if applicable 4 Loosen the two RTM face plate screws RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation 5 Unlatch the upper handle and rotate both handles fully outward 6 Remove the RTM from the slot RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors 3 1 Overview This chapter describes e Mechanical layout e Face plate interfaces e Onboard connectors 3 2 Blade Layout The following figure provides an overview of the mechanical layout of the blade Figure 3 1 Mechanical Layout RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors 3 3 Face Plate Connectors and LEDs This section describes the connectors and LEDs of the RTM s face plate Figure3 2 X Face Plate 3 ACT c o M 1 s s oe oe RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors Figure3 3 X Face Plate with optional E1 T1 Connectors U 5 B E T H 2 E T H 1 RESET RTM ATCA 7301 HDD RTM ATCA7301 Inst
12. trained by Emerson or persons qualified in electronics or electrical engineering are authorized to install remove or maintain the product The information given in this manual is meant to complete the knowledge of a specialist and must not be used as replacement for qualified personnel Keep away from live circuits inside the equipment Operating personnel must not remove equipment covers Only factory authorized service personnel or other qualified service personnel may remove equipment covers for internal subassembly or component replacement or any internal adjustment Do not install substitute parts or perform any unauthorized modification of the equipment or the warranty may be voided Contact your local Emerson representative for service and repair to make sure that all safety features are maintained This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications RTM ATCA7301 Installation and Use 6806800K95A 45 Safety Notes Operation of this equipment a residential area is likely to cause harmful interference in
13. A Hardware Preparation and Installation 7 Fully insert the RTM and lock it to the shelf by pressing the two components of the lower and the upper handles together and turning the handles toward the face plate 8 Tighten both face plate screws on the RTM 9 Wait until the blue LED on the RTM is OFF A switched off blue LED indicates that the payload of the RTM has become active 10 Plug interface cable into face plate connectors if applicable 11 Reboot the front blade This is necessary so that the OS of the front blade can recognize the SAS controller or any other PCI device located on the RTM RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation 2 42 Removing the RTM Removal Procedure The following procedure describes the removal of the RTM It assumes that your system is powered If your system is unpowered you can disregard the blue LED and thus skip the respective step In this case itis a purely mechanical procedure 1 Unlatch the lower handle outward by squeezing the lever and the latch together and turning the handle outward only enough to unlatch the handle from the face plate that means until you feel a resistance Do not rotate the handle fully outward The blue LED blinks indicating that the shelf manager is informed about the desire of the blade to power down the payload of both the front blade and the RTM and the power down process is ongoing 2 Wait until
14. E Embedded Computing for Business Critical Continuity RTM ATCA7301 Installation and Use P N 6806800K95A May 2010 EMERSON Network Power 2010 Emerson All rights reserved Trademarks Emerson Business Critical Continuity Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co 2008 Emerson Electric Co All other product or service names are the property of their respective owners Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries Java and all other Java based marks are trademarks or registered trademarks of Sun Microsystems Inc in the U S and other countries Microsoft Windows and Windows Me are registered trademarks of Microsoft Corporation and Windows XP is a trademark of Microsoft Corporation PICMG CompactPCI AdvancedTCA and the PICMG CompactPCI and AdvancedTCA logos are registered trademarks of the PCI Industrial Computer Manufacturers Group UNIX is a registered trademark of The Open Group in the United States and other countries Notice While reasonable efforts have been made to assure the accuracy of this document Emerson assumes no liability resulting from any omissions in this document or from the use of the information obtained therein Emerson reserves the right to revise this document and to make changes from time to time in the content her
15. Face Plate LEDs Name Color Description ETHx ACT Yellow Indicates activity on Ethernet port LNK Green Indicates link on Ethernet port HDD Green Indicates access or activity on onboard SAS hard disk RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors Table 3 2 Face Plate LEDs continued Name Color Description OOS Red Out Of Service This LED is controlled by higher layer software such as middleware or applications OK Green Payload Power Status Green The payload power has been enabled by the IPMC Note that this LED indicates the payload power status both in the early power state and the normal blade operation OFF Payload power is disabled ATN Amber Attention This LED is controlled by higher layer software such as middleware or applications H S Blue FRU State Machine During blade installation Permanently blue On board IPMC powers up Blinking blue Blade communicates with shelf manager OFF Blade is active During blade removal Blinking blue Blade notifies shelf manager of its desire to deactivate Permanently blue Blade is ready to be extracted 3 4 Onboard Connectors The HD variant of the RTM provides an onboard Serial Attached SCSI SAS connector The SAS connector allows to install an onboard 2 5 SAS hard disk which is available as accessory kit called ATCA 7301 HD SAS RTM ATCA7301 Installation and Use 6806800K95A
16. Temperature Spots on the RTM ATCA7301 HDD Figure 2 1 21 RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation Table 2 2 Critical Temperature Limits Location Temperature Description 1 90 C 194 F Transformer housing 2 90 C 194 F Transformer housing If you integrate the blade in your own system please contact your local sales representative for further safety information 2 3 2 Power Requirements The RTM gets safety extra low voltage SELV power from the front blade 2 4 Module Installation and Removal The RTM must be installed into a AdvancedTCA system without a zone 3 midplane The RTM provides support for basic hot swap that means it can be installed removed and replaced in a powered system However after the RTM is installed or replaced in a powered system the front blade has to be rebooted so that the OS can recognize the SAS controller or other PCI devices located on the RTM RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation NOTICE RTM Damage Installing the RTM with other blades than the ATCA 7301 may damage the RTM and the front blade Only install the RTM with the Emerson ATCA 7301 blade Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life Before touching the RTM or elect
17. allation and Use 6806800K95A Controls LEDs and Connectors 3 3 1 3 3 1 1 3 3 1 2 Face Plate Connectors The following interfaces are available on the face plate One USB 2 0 connector e Two 10 100 1000 Base T Ethernet connectors e One serial connector One SAS connector e Eight HDD variant E1 T1 RJ 45 connectors USB Connector The USB 2 0 interface can be used for connecting a keyboard an USB memory stick an USB CD ROM drive or other USB devices The pin assignment of the USB connector is given in the following figure Figure 3 4 USB Connector Pinout VP5_USB 1 USB_x_D USB_x_D GND 4 Ethernet Connectors The Ethernet connectors ETH 1 2 can be used for connecting other Ethernet devices The pin assignment of the Ethernet connectors is given in the following figure Figure 3 5 Ethernet Connector Pinout 10Base T or 1000Base T 100Base TX 1 ETH_TX ETH DA 2 ETH TX ETH DA 3 ETH RX ETH DB 1 4 n c ETH DC 5 _ E 6 ETH_RX ETH_DB 8 ETH_DD 8 n c ETH_DD RTM ATCA7301 Installation and Use 6806800K95A Controls LEDs and Connectors 3 3 1 3 Serial Connector The serial connector can be used for connecting a console The pin assignment of the serial connector is given in the following figure Figure3 6 Serial Connector Pinout 6 n c 6 1 n c 1 y COM1 RS232 RXD 2 8 n c COM1 RS232 3 nac 4
18. e f r Sie zust ndige Gesch ftsstelle von Emerson So stellen Sie sicher dass alle sicherheitsrelevanten Aspekte beachtet werden RTM ATCA7301 Installation and Use 6806800K95A 49 Sicherheitshinweise UN En EMV Das Produkt wurde in einem Emerson Standardsystem getestet Es erf llt die f r digitale Ger te der Klasse A g ltigen Grenzwerte in einem solchen System gem den FCGRichtlinien Abschnitt 15 bzw EN 55022 Klasse A Diese Grenzwerte sollen einen angemessenen Schutz vor St rstrahlung beim Betrieb des Produktes in Gewerbe sowie Industriegebieten gew hrleisten Das Produkt arbeitet im Hochfrequenzbereich und erzeugt St rstrahlung Bei unsachgem em Einbau und anderem als in diesem Handbuch beschriebenen Betrieb k nnen St rungen im Hochfrequenzbereich auftreten Wird das Produkt in einem Wohngebiet betrieben so kann dies mit gro er Wahrscheinlichkeit zu starken St rungen f hren welche dann auf Kosten des Produktanwenders beseitigt werden m ssen nderungen oder Modifikationen am Produkt welche ohne ausdr ckliche Genehmigung von Emerson durchgef hrt werden k nnen dazu f hren dass der Anwender die Genehmigung zum Betrieb des Produktes verliert Boardprodukte werden in einem repr sentativen System getestet um zu zeigen dass das Board den oben aufgef hrten EMV Richtlinien entspricht Eine ordnungsgem e Installation in einem System welches die EMV Richtlinien erf llt stellt sicher dass das Produkt gem
19. ed information refer to the RTM ATCA 7301 Control via IPMI Programmer s Reference RTM ATCA7301 Installation and Use 6806800K95A Appendix A Related Documentation A 1 Emerson Network Power Embedded Computing Documents The Emerson Network Power Embedded Computing publications listed below are referenced in this manual You can obtain electronic copies of Emerson Network Power Embedded Computing publications by contacting your local Emerson sales office For documentation of final released GA products you can also visit the following website http www emersonnetworkpowerembeddedcomputing com gt Solution Services gt Technical Documentation Search This site provides the most up to date copies of Emerson Network Power Embedded Computing product documentation Table A 1 Emerson Publications Document Title Publication Number RTM ATCA 7301 Control via IPMI Programmer s Reference 6806800D93 ATCA 7301 Installation and Use 6806800D86 ATCA 7301 Control via IPMI Programmer s Reference 6806800D92 Basic Blade Services Software on ATCA 7301 Programmer s Reference 6806800G32 A 2 Related Specifications For additional information refer to the following table for related specifications As an additional help a source for the listed document is provided Please note that while these sources have been verified the information is subject to change without notice Table A 2 Related Specifications
20. emp change 0 25 C min according to NEBS Standard 0 25 C min GR 63 CORE Rel humidity 5 to 90 non condensing according to 5 to 95 non condensing according to Emerson internal environmental Emerson internal environmental requirements requirements Vibration 0 1 gfrom 5 to 100Hzandbackto5Hzata 5 20 Hz at 0 01 g Hz rate of 0 1 octave minute 20 200 Hz at 3 0 dB octave Random 5 20 Hz at 1 m Sec Random 20 200 Hz at 3 m Sec Shock Half sine 11 m Sec 30 mSec Sec Blade level packaging Half sine 6 mSec at 180 m Sec Free fall 1 200 mm all edges and corners 1 0 m packaged per ETSI 300 019 2 2 blade level packaging 100 mm unpacked per GR 63 CORE RTM ATCA7301 Installation and Use 6806800K95A 19 Hardware Preparation and Installation During the safety qualification of this blade the following on board locations were identified as critical with regards to the maximum temperature during blade operation To guarantee proper blade operation and to ensure safety you have to make sure that the temperatures at the locations specified in the following are not exceeded If not stated otherwise the temperatures should be measured by placing a sensor exactly at the given locations For your convenience all temperature spots are shown in the following figure that provides a detailed RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation view of the blade Critical
21. emphasize a word Screen Used for on screen output and code related elements or commands in body text Courier Bold Used to characterize user input and to separate it from system output Reference Used for references and for table and figure descriptions File gt Exit Notation for selecting a submenu lt text gt Notation for variables and keys text Notation for software buttons to click on the screen and parameter description Repeated item for example node 1 node 2 node 12 Omission of information from example command that is not necessary at the time being Ranges for example 0 4 means one of the integers 0 1 2 3 and 4 used in registers Logical OR RTM ATCA7301 Installation and Use 6806800K95A 11 About this Manual Notation Description A Indicates hazardous situation which if not avoided could result in death or serious injury XXXOOQOOOQOOODUOCDODOODOOOQOOOOOOODQOOODOOOOOQOO0OOCCECE Indicates hazardous situation which if not avoided may result in minor or moderate injury 3OO0OO00O0O0000000000000000000000000000000000O00000000 C KIND NHI OU X X002 XOU OOO OOOO IO ORI X00 NE XOU XOUX OU IE MERK CX COCOS OOO OOOO OG Indicates a property dama
22. eof without obligation of Emerson to notify any person of such revision or changes Electronic versions of this material may be read online downloaded for personal use or referenced in another document as a URL to a Emerson website The text itself may not be published commercially in print or electronic form edited translated or otherwise altered without the permission of Emerson It is possible that this publication may contain reference to or information about Emerson products machines and programs programming or services that are not available in your country Such references or information must not be construed to mean that Emerson intends to announce such Emerson products programming or services in your country Limited and Restricted Rights Legend If the documentation contained herein is supplied directly or indirectly to the U S Government the following notice shall apply unless otherwise agreed to in writing by Emerson Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph b 3 of the Rights in Technical Data clause at DFARS 252 227 7013 Nov 1995 and of the Rights in Noncommercial Computer Software and Documentation clause at DFARS 252 227 7014 Jun 1995 Contact Address Emerson Network Power Embedded Computing 2900 South Diablo Way Suite 190 Tempe AZ 85282 USA Contents About this Manual ass p RICO EA hi VP hederen 9 por RER baa EE ER EEE EEA
23. etriebssystems bevor Sie das RTM aus einem laufenden System entfernen Emerson und unsere Zulieferer unternehmen gr te Anstrengungen um sicherzustellen dass sich Pins und Stecker von Boards vor dem Verlassung der Produktionsst tte in einwandfreiem Zustand befinden Verbogene Pins verursacht durch fehlerhafte Installation oder durch Installation von Boards mit besch digten Steckern kann die durch Emerson gew hrte Garantie f r Boards und Backplanes erl schen lassen Kabel und Stecker Besch digung des Produktes Bei den RJ 45 Steckern die sich an dem Produkt befinden handelt es sich entweder um Twisted Pair Ethernet TPE oder um E1 T1 Stecker Beachten Sie dass ein versehentliches Anschlie en einer E1 T1 Leitung an einen TPE Stecker das Produkt zerst ren kann e Kennzeichnen Sie deshalb TPE Anschl sse in der N he Ihres Arbeitsplatzes deutlich als Netzwerkanschl sse Stellen Sie sicher dass die L nge eines mit Ihrem Produkt verbundenen TPE Kabels 100 m nicht berschreitet e Das Produkt darf ber die TPE Stecker nur mit einem Sicherheits Kleinspannungs Stromkreis SELV verbunden werden Bei Fragen wenden Sie sich an Ihren Systemverwalter 52 RTM ATCA7301 Installation and Use 6806800K95A Sicherheitshinweise Umweltschutz Entsorgen Sie alte Batterien und oder Blades Systemkomponenten RTMs stets gem der in Ihrem Land g ltigen Gesetzgebung und den Empfehlungen des Herstellers RTM ATCA7301 Installati
24. features Two 10 100 1000 Base T Ethernet interfaces with separate SMD RJ 45 connectors Onboard SAS controller supporting four SAS ports Two SAS ports toward AMC bay 1 Two SAS ports on face plate connector One RS 232 interface with mini DB9 connector on face plate One USB2 0 port on face plate Hot plug in ability Module management according to IPMI specification 2 0 Four user LEDs the face plate Reset button at the face plate Onboard 2 5 SAS hard disk drive HDD mounting option Up to eight ET T1 ports four from each AMC bay supporting transformers and prim sec protection circuitry RTM ATCA7301 Installation and Use 6806800K95A 13 Introduction 1 2 Standard Compliances This product meets the following standards Table 1 1 Standard Compliances Standard Description UL 60950 1 Legal safety requirements EN 60950 1 IEC 60950 1 CAN CSA C22 2 No 60950 1 CISPR 22 EMC requirements legal on system level predefined CISPR 24 Emerson system EN 55022 EN 55024 FCC Part 15 Industry Canada ICES 003 VCCI Japan AS NZS CISPR 22 EN 300 386 NEBS Standard GR 1089 CORE NEBS Standard GR 63 CORE Environmental requirements ETSI EN 300019 series PICMG 3 0 Defines mechanics blade dimensions power distribution power and data connectors and system management PICMG 3 1 Defines Ethernet on AdvancedTCA data transport vg The product has been designed to meet the directive on the
25. ge message No danger encountered Pay attention to important 20000000000000000000000000000000000000000000000000 information This manual has been revised and replaces all prior editions 6806800K95A May 2010 G version Comments and Suggestions We welcome and appreciate your comments on our documentation We want to know what you think about our manuals and how we can make them better Mail comments to us by filling out the following online form http www emersonnetworkpowerembeddedcomputing com gt Contact Us gt Online Form In Area of Interest select Technical Documentation Be sure to include the title part number and revision of the manual and tell us how you used it 12 RTM ATCA7301 Installation and Use 6806800K95A Chapter 1 Introduction 1 1 Features The RTM ATCA7301 is a rear transition module as defined in PICMG 3 0 Revision 2 0 AdvancedTCA Base Specification and PICMG 3 1 Revision 1 0 Specification Ethernet Fiber Channel for AdvancedTCA Systems It provides several Ethernet interfaces connected to the front blade via the Zone 3 connector It provides the following
26. he Entladung und unsachgem er Ein und Ausbau des Produktes kann Schaltkreise besch digen oder ihre Lebensdauer verk rzen Bevor Sie das Produkt oder elektronische Komponenten ber hren vergewissern Sie sich da Sie in einem ESD gesch tzten Bereich arbeiten Besch digung des Produktes Fehlerhafte Installation des Produktes kann zu einer Besch digung des Produktes f hren Verwenden Sie die Handles um das Produkt zu installieren deinstallieren Auf diese Weise vermeiden Sie dass das Face Plate oder die Platine deformiert oder zerst rt wird Besch digung des Produktes der Backplane oder von System Komponenten Verbogene Pins oder lose Komponenten k nnen zu einer Besch digung des Produktes der Backplane oder von Systemkomponenten f hren berpr fen Sie daher das Produkt sowie die Backplane vor der Installation sorg ltig und stellen Sie sicher dass sich beide in einwandfreien Zustand befinden und keine Pins verbogen sind Besch digung des Produktes Wenn Sie das RTM mit anderen Blades als dem ATCA 7301 installieren wird RTM ATCA7301 Installation and Use 6806800K95A 51 Sicherheitshinweise das RTM besch digt Installieren Sie das RTM deshalb nur zusammen mit dem Emerson ATCA 7301 Front Blade Datenverlust Wenn Sie das RTM aus einem laufenden System entfernen k nnen Daten die gerade auf die Festplatte des RTMs geschrieben werden verloren gehen Trennen Sie deshalb die Festplatte des RTMs von den Services des B
27. is divided into the following chapters and appendices Aboutthis Manual on page 9 lists all conventions and abbreviations used in this manual and outlines the revision history e Safety Notes on page 45 describes the safety information which has to be regarded e Sicherheitshinweise on page 49 provides a German translation of the chapter Safety Notes e Introduction on page 13 gives an overview of the product e Hardware Preparation and Installation on page 17 describes the exchange prerequisites and procedures e Controls LEDs and Connectors on page 29 describes external interfaces of the blade This includes connectors and LEDs e Functional Description on page 41 describes in more detail functional blocks of the product e Related Documentation on page 43 lists related documentation and specifications Abbreviations This document uses the following abbreviations Abbreviation Definition AdvancedTCA Advanced Telecom Computing Architecture tm AMC Advanced Mezzanine Card ARTM Advanced Rear Transition Module BMC Baseboard Management Controller CISPR Comit Internationale Sp cial des Perturbations Radioelectrotechnique International Special Committee on Radio Interference IEC EMC Electromagnetic Compatibility EMV Elektromagnetische Vertr glichkeit EN European Norm ESD Electrostatic Discharge RTM ATCA7301 Installation and Use 6806800K95A 9 About this Manual
28. lle notwendigen Informationen zum Einbau und zum Umgang mit dem Produkt in diesem Handbuch bereit zu stellen Da es sich jedoch um ein komplexes Produkt mit vielf ltigen Einsatzm glichkeiten handelt k nnen wir die Vollst ndigkeit der im Handbuch enthaltenen Informationen nicht garantieren Falls Sie weitere Informationen ben tigen sollten wenden Sie sich bitte an die f r Sie zust ndige Gesch ftsstelle von Emerson Das System erf llt die f r die Industrie geforderten Sicherheitsvorschriften und darf ausschlie lich f r Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden Einbau Wartung und Betrieb d rfen nur von durch Emerson ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgef hrt werden Die in diesem Handbuch enthaltenen Informationen dienen ausschlie lich dazu das Wissen von Fachpersonal zu erg nzen k nnen dieses jedoch nicht ersetzen Halten Sie sich von stromf hrenden Leitungen innerhalb des Produktes fern Entfernen Sie auf keinen Fall Abdeckungen am Produkt Nur werksseitig zugelassenes Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen entfernen um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen Installieren Sie keine Ersatzteile oder f hren Sie keine unerlaubten Ver nderungen am Produkt durch sonst verf llt die Garantie Wenden Sie sich f r Wartung oder Reparatur bitte an di
29. mage circuits or shorten their life Before touching the product or electronic components make sure that your are working in an ESD safe environment RTM ATCA7301 Installation and Use 6806800K95A Safety Notes Product Damage Incorrect installation of the product can cause damage of the product Only use handles when installing removing the product to avoid damage deformation to the face plate and or PCB Damage to the Product Backplane or System Components Bent pins or loose components can cause damage to the product the backplane or other system components Therefore carefully inspect the product and the backplane for both pin and component integrity before installation RTM Damage Installing the RTM with other blades than the ATCA 7301 may damage the RTM and the front blade Only install the RTM with the Emerson ATCA 7301 blade Date Loss If you remove the RTM from a powered system data that is in the process of being written to the hard disk located on the RTM may be lost Disconnect the RTM hard disk from OS services before removing the RTM from a powered system RTM ATCA7301 Installation and Use 6806800K95A 47 Safety Notes Emerson and our suppliers take significant steps to ensure there are no bent pins on the backplane or connector damage to the boards prior to leaving the factory Bent pins caused by improper installation or by inserting boards with damaged connectors could void the Emerson warranty f
30. on and Use 6806800K95A 53 Sicherheitshinweise 54 RTM ATCA7301 Installation and Use 6806800K95A Index A abbreviations 9 B block diagram 41 C change history 12 comments and suggestions 12 compliances 14 component location 29 connectors face plate 32 onboard 36 contact address 12 conventions 11 D declaration of conformity 15 dimensions 16 DoC 15 E E1 T1 connector 34 Ethernet connector 32 F face plate E1 T1 34 Ethernet 32 LEDs 35 SAS 33 serial 33 USB 32 features 13 feedback 12 installation 24 L LEDs activity 35 ATN 36 blue 36 RTM ATCA7301 Installation and Use 6806800K95A hard disk 35 hot swap 36 link 35 OK 36 OOS 36 M MMC 42 order numbers 16 R related documents 43 removal 26 requirements environmental 18 legal 14 power 22 temperature limits 22 RoHS 14 S SAS connector 33 location 37 pin assignment 38 SELV 22 sensors 42 serial connector 33 standards 14 T temperatures non operating 19 operating 19 U USB connector 32 W weight 16 55 Index 56 RTM ATCA7301 Installation and Use 6806800K95A HOW TO REACH LITERATURE AND TECHNICAL SUPPORT For literature training and technical assistance and support programs visit www emersonnetworkpower com embeddedcomputing Emerson Network Power www emersonnetworkpower com embeddedcomputing The global leader in enabling Bu
31. or the backplane or boards Cabling and Connectors Product Damage The 45 connector s on the face plate are either twisted pair Ethernet TPE or ET T1 interfaces Connecting an ET T1 line to an Ethernet connector may damage the product e Make sure that TPE connectors near your working area are clearly marked as network connectors e Verifythatthelength of an electric cable connected to a TPE bushing does not exceed 100 m e Make sure the TPE bushing of the product is connected only to safety extra low voltage circuits SELV circuits If in doubt ask your system administrator Environment Always dispose of used blades system components and RTMs according to your country s legislation and manufacturer s instructions 48 RTM ATCA7301 Installation and Use 6806800K95A Sicherheitshinweise Dieses Kapitel enth lt Hinweise die potentiell gef hrlichen Prozeduren innerhalb dieses Handbuchs vorrangestellt sind Beachten Sie unbedingt in allen Phasen des Betriebs der Wartung und der Reparatur des Systems die Anweisungen die diesen Hinweisen enthalten sind Sie sollten au erdem alle anderen Vorsichtsma nahmen treffen die f r den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind Wenn Sie diese VorsichtsmaBnahmen oder Sicherheitshinweise die an anderer Stelle diese Handbuchs enthalten sind nicht beachten kann das Verletzungen oder Sch den am Produkt zur Folge haben Emerson ist darauf bedacht a
32. rds models listed below Table 1 3 Order Numbers Order Number Description RTM ATCA 7301 Rear transition module with eight E1 T1 ports and onboard hard disk for ATCA 7301 blade RoHS 6 6 Note This product is EOL Please contact our sales representatives for further details RTM ATCA7301 Rear transition module onboard hard disk for ATCA 7301 blade RoHS 6 6 ATCA 7301 HD SAS 147GB SAS HDD for the RTM 16 RTM ATCA7301 Installation and Use 6806800K95A Chapter 2 Hardware Preparation and Installation 2 1 Overview This chapter describes e Unpacking and inspecting the module e Environmental and power requirements e Module installation and removal 2 2 Unpacking and Inspecting the Module NOTICE Damage of Circuits Electrostatic discharge and incorrect installation and removal of the blade can damage circuits or shorten their life Before touching the blade or electronic components make sure that your are working in an ESD safe environment Shipment Inspection To inspectthe shipment perform the following steps 1 Verify that you have received all items of your shipment Printed user manual RTM ATCA7301 module Any optional items ordered 2 Check for damage and report any damage or differences to the customer service RTM ATCA7301 Installation and Use 6806800K95A 17 Hardware Preparation and Installation 3 Remove the desiccant bag shipped together with the blade and dispose of
33. restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Directive 2002 95 14 RTM ATCA7301 Installation and Use 6806800K95A Introduction Figure 1 1 Declaration of Conformity Declaration of Conformity DoC According to EN 17050 1 2004 Manufacturer s Name Emerson Network Power Embedded Computing Manufacturer s Address Emerson Network Power Embedded Computing GmbH Lilienthalstrasse 15 85579 Neubiberg Germany Declares that the following product Product ATCA Blades with Rear Transition Modules and Accessories Model Names Numbers ATCA 7301 RTM ATCA 7301 RTM ATCA7301 ATCA 7301 HD SAS ATCA 7301 MEM in accordance with the requirements of 2004 108 EC amp 2006 95 EC and their amending directives has been desigred and manufactured to the following specifications EN 60950 1 A11 2009 EN 55022 2006 EN 55024 1998 A1 2001 A2 2003 ETSI EN 300 386 V1 3 3 2005 04 l r H Kai Holz Director Engineering Issue Date 12 MAY 2010 C EMERSON Network Power RTM ATCA7301 Installation and Use 6806800K95A 15 Introduction 1 3 Mechanical Data The following table provides details on the blade s mechanical data Table 1 2 Mechanical Data Data Type Value Dimension length x width x height 322 3 mmx 70 mm x 29 mm Weight 0 6 kg 1 4 Ordering Information As of the printing date of this manual this quide supports the boa
34. ronic components make sure that you are working in an ESD safe environment Date Loss If you remove the RTM from a powered system data that is in the process of being written to the hard disk located on the RTM may be lost Disconnect the RTM hard disk from OS services before removing the RTM from a powered system RTM ATCA7301 Installation and Use 6806800K95A Hardware Preparation and Installation 2 4 1 Installing the RTM Installation Procedure The following procedure describes the installation of the RTM It assumes that your system is powered If your system is unpowered you can disregard the blue LED and thus skip the respective step In this case itis a purely mechanical installation 1 Locate the slot the RTM is to be installed into the shelf s rear which must be the same as that of the front blade 2 Ensure that the top and the bottom handles of the RTM are in an outward position by squeezing the lever and the latch together 3 Insert the RTM into the shelf by placing the top and bottom edges in the card quides of the slot 4 Slide the RTM into the slot 5 Apply equal and steady pressure to the RTM to carefully slide the RTM into the shelf until you feel resistance Continue to gently push the RTM until the RTM connectors engage 6 Squeeze the lever and the latch together and hookthe lower and the upper handle into the shelf rail recesses RTM ATCA7301 Installation and Use 6806800K95
35. siness Critical Continuity AC Power Systems Embedded Computing Outside Plant I Services Connectivity u Embedded Power Power Switching amp Control Site Monitoring BI DC Power Systems Integrated Cabinet Solutions Precision Cooling I Surge amp Signal Protection Emerson Business Critical Continuity Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co All other product or service names are the property of their respective owners O 2009 Emerson Electric Co
36. which case the user will be required to correct the interference at his own expense Changes or modifications not expressly approved by Emerson could void the user s authority to operate the equipment Board products are tested in a representative system to show compliance with the above mentioned requirements A proper installation in a compliant system will maintain the required performance Use only shielded cables when connecting peripherals to assure that appropriate radio frequency emissions compliance is maintained Operation Product Damage Surface of the Product High humidity and condensation on the product surface causes short circuits Do not operate the product outside the specified environmental limits Make sure the product is completely dry and there is no moisture on any surface before applying power Overheating and Product Damage Operating the product without forced air cooling may lead to overheating and thus damage of the product When operating the product make sure that forced air cooling is available in the shelf Installation 46 Damage of the Product and Additional Devices and Modules Incorrect installation or removal of additional devices or modules may damage the product or the additional devices or modules Before installing or removing additional devices or modules read the respective documentation Damage of Circuits Electrostatic discharge and incorrect installation and removal of the product can da
Download Pdf Manuals
Related Search