Hacker-X-Pro
Contents
1. manuals and accessories Warning Once the Motor Battery Pack is connected handle the model with extreme care Ensure that you are well clear of the propeller at all times Rotating propellers are extremely dangerous Always Connect the motor battery pack just before flight and disconnect it immediately after landing the model Warning Even when the switch is off remember the Motor Battery pack may be connected handle the model with extreme care and stay well clear of the Propeller Copyright 01 06 Hacker Motor GmbH 5 Declaration of conformity The described products are in compliance with the relevant and applicable EC guidelines for electromagnetic compatibility 89 336 EWG 92 31 EWG 93 68 EWG Many happy landings Hacker Motor GmbH Hummler Str 5 Tel 0049 0 8761 752 129 Fax 0049 0 8761 754 314 EMAIL info hacker motor com D 85416 Niederhummel Copyright 01 06 Hacker Motor GmbH 62. V mise usen aias moss ahead 5 Lipos 14 5V 3 Under voltage reduces power when the battery gets low _ _ _ _ cuts off power when the battery getslow _ _ _ _ _ 4 Acceleration Low VVVVV Medium VV VV VV VV VV High VVV VVV VVV VVV VVV 5 Timing Automatic 7 30 degree recommended Soft 7 degree 2 pole motors E Hard 22 30 degree multipole motors Sie Se ES Sel ce 6 Frequency 8 kHz recommended AAAA 16 kHz 1 111 7 Rotation reverse Reverse motor rotation WWW WW 8 Active RPM Control Heli Governormode rpm control Off up to 20 000 electrical RPM up to 50 000 electrical RPM above 50 000 electrical RPM electrical RPM on two pol motors for a 4 pol motor for example Copyright 01 06 Hacker Motor GmbH 3 50 000 electrical RPM 2 25 OOORPM 10 pol motors electrical 50 OOORPM 5 10 OOORPM and so on Trouble shooting Switch ON the transmitter and check the throttle channel settings are 100 for computer radios For Futaba Radios program the Servo Reverse function on the throttle channel Set the throttle to closed or brake position Locate the controller to Avoid multiple touches of the connectors when installing a fresh motor battery pack You must hear a beep Between switching on the switch and the beep the throttle stick must not be moved If you do not hear a beep switch off the switch disconnect the power connectors wai
3. X Pro Speedcontroller d cke Brushless Motors Dear Customer Thank you for your purchase of the X Series Controller a new generation of sensorless speed controllers especially for Hacker Brushless A Series Motors and other Brushless Motor Designs Special programming options are provided to ensure the best possible power and performance from your motor system Brushless systems offer high power efficiency combined with low weight and compact dimensions For best performance and reliability from your Controller use only High quality connectors motors and batteries Please pay careful attention to the following instructions before you start to work with your new motor and speed controller Connections The speed controller can be connected to the motor by direct soldering or with high quality connectors Always use new connectors which should be soldered carefully to the cables and insulated with Heat shrink tubing It is possible to extend the cables to the motor battery pack up to a maximum of 8 inches Deans Ultra or other high quality connectors are recommended for connecting the motor battery pack to the controller e Solder Controller to the Motor wires Solder appropriate connectors to the Battery wires Insulate all Solder connections with Heat Shrink Tubing Plug the JR connector into the receiver throttle channel When connecting controller to battery pack care should be taken to ensure that multiple tou
4. ches of the connectors are not made Reversing the motor directions is achieved by the exchanging the position of any two wires connected to the motor or by programming rotation reverse Installing the Controller Install the speed controller in the model so that it is isolated from vibration and shock using Velcro or double sided foam tape Allow space around it for cooling Make sure that there is sufficient cooling of the motor and speed controller by ducting air through adequate cooling holes from the outside airflow Main power packs should be connected at one attempt Copyright 01 06 Hacker Motor GmbH 1 The X speed controllers have an optimal default setup for A Motors Factory default settings Brake Off Battery type ESC with BEC 3S Li Poly ca 8 7V Battery type ESC Opto without BEC 5S Li Poly ca 14 5V Under voltage Reduce power Acceleration Fast Timing Auto Frequency 8KHz Active RPM Control Helimode Governormode Off Normal start up When throttle stick is off connect battery pack switch on the controller if switch is installed you will hear one beep for Brake on or two tones for Brake off For changing the default setup please read the following manual ESC program procedure It is possible to program the ESC in two different ways by using a Computer with Hacker X Pro USB Interface and a special software which can be acquired see then enclosed operating instructions T
5. e This warranty does not cover any component parts damaged by use or modification Hacker Brushless Motors reserves the right to change or modify this warranty without notice In that Hacker Brushless Motors has no control over the final assembly no liability shall be assumed nor accepted for any damage resulting from the use by user of the final assembled product the user accepts all resulting liability All returns require a Merchandise Return Authorization MRA which can be obtained by contacting Hacker Brushless Motors No returns of any type will be accepted without a MRA number and will be returned to the sender The following information is required for obtaining a MRA number Customer name or Store name Invoice number part or model number and explanation of defect or problem e Hacker Brushless Motors must authorize all returns within 7 days from receipt of order e All returns must have a copy of the original invoice with MRA number e All returning packages must have the MRA number clearly marked on the outside of the packaging All packages shall be inspected upon delivery All claims for damaged products must be made with carrier within 3 days of the receipt of the package All defective items must be processed through the Manufacturer or the Distributor of the product Sender must prepay all transportation and insurance charges All returning items must be in new saleable condition They must have original packing material
6. he USB software offers still additional adjusting parameters variable cutoff voltage for LiPo cells Brake off soft hard finer gradations in the Motortiming acceleration in three stages selectable updates for the X Pro ESC programming by throttlestick With throttle stick at full power connect the battery and wait for 5 sec Program mode is entered when you hear two low tones and two high tones __ Each time you enter the programming mode you are allowed to make one change and then you will automatically exit the programming mode To change more than one parameter you will have to re enter the programming mode each time 1 Brake To change the brake function as soon as you hear the programming tones mentioned above move the throttle stick to low position Brake function will be inverted IE If brake was on it now will be off To change any of the remaining functions enter the programming mode as detailed above Leave the throttle at high position until you are within the five sets of beeps as detailed in each of the choices below When you arrive at the choice you want to make move the throttle to low position while that series of 5 tones are still being heard WARNING the motor will run now by moving the throttlestick Copyright 01 06 Hacker Motor GmbH 2 2 Battery type Voltage Cut off NiCd 0 te ee we 2 Lipos 5 8V 3 Lipos 8 7V Following options only on OPTO controllers A Lipos 116
7. t for 5 seconds and repeat the procedure of connecting and switching on If you do not hear beep again check the following o Is JR connector plugged in throttle chanel o Is the throttle stick in closed position OFF o Is the throttle channel in normal position for Futaba in the Reverse position The position of full throttle will be adjusted automatically All programming will be stored e The speed controller will turn off the motor when the main power pack voltage falls under 5 5 V or at the voltage wich is programed in step under voltage It depends on which occurs first Temperature overload protection is built into the speed controller it turns off the motor when the temperature reaches 230 F 110 C These speed controllers are equipped with protection functions that take care of correct start and operation of the motor across the whole range of RPM Current and Voltage Do Not connect the speed controller to just any kind of power source Take care to ensure the right polarity of NiCd NiMH or LiPoly power packs only Do not connect the motor battery to the wrong polarity the speed controller will be severely damaged Controllers connected to the wrong battery polarity WILL NOT be covered under the warranty Copyright 01 06 Hacker Motor GmbH 4 Warranty Terms and Conditions Hacker Brushless Motors warrants products to be free from defects at the date of purchas
Download Pdf Manuals
Related Search