Getting Started
Contents
1. aom1 1f eps Figure 2 Low Pass Filter 11 80 Series V Getting Started Manual Bar Graph The analog bar graph functions like the needle on an analog meter but without the overshoot The bar graph updates 40 times per second Because the graph responds 10 times faster than the digital display it is The number of lit segments indicates the measured value and is relative to the full scale value of the selected range In the 60 V range for example the major divisions on the scale represent 0 15 30 45 and 60 V An input of 30 V lights the negative sign and the useful for making peak and null adjustments and observing rapidly segments up to the middle of the scale changing inputs The graph is not shown for capacitance frequency The bar graph also has a zoom function as described under Zoom counter functions temperature or peak min max 12 MIN MAX while in MIN MAX mode PEAK MIN MAX AutoHOLD MIN MAX hold for 1 second Mode in the Users Manual located on the 80 Series V User Manuals CD Table 6 MIN MAX Functions Enter MIN MAX recording mode The Meter is locked in the range displayed before you entered MIN MAX mode Select the desired measurement function and range before entering MIN MAX The Meter beeps each time a new minimum or maximum value is recorded Step through maximum MAX minimum MIN and average AVG and present values Model 87 only Select 100 m2. 18 Multimeters Specifications Table 12 Capacitance and Diode Function Specifications Function Rage Resolution Accuracy 10 00 nF 100 0 nF 1 000 uF 10 00 uF 100 0 uF 9999 uF 1 With a film capacitor or better using Relative mode to zero residual Table 13 Frequency Counter Specifications Function Range Resolution Frequency 199 99 0 01 Hz E 0 005 1 0 5 Hz to 200 kHz pulse 1999 9 0 1 Hz 0 005 1 width gt 2 us 19 999 kHz 0 001 kHz E 0 005 1 199 99 kHz 0 01 kHz 0 005 1 gt 200 kHz 0 1 kHz unspecified 19 80 Series V Getting Started Manual Table 14 Frequency Counter Sensitivity and Trigger Levels Minimum Sensitivity RMS Sine wave Approximate Trigger Level Input Range 5Hz 20kHz 0 5Hz 200kHz DC Voltage Function 600 mV dc 70 mV to 400 Hz 70 mV to 400 Hz 600 mV ac 150 mV 150 mV 6V 0 3V 0 7V 60 V 3V 7 V lt 140 kHz 600 V 30V 70 V 14 0 kHz 1000 V 100 V 200 V x1 4 kHz 0 0 to 99 9 Within 0 2 per kHz 0 1 96 for rise times 1 us 1 Maximum input for specified accuracy 10X Range or 1000 V 20 Multimeters Specifications Table 15 Electrical Characteristics of the Terminals Input Common Mode Sud Impedance Rejection Ratio Normal Mode Rejection nominal EST kQ unbalance 1000 V rms 10 MQ lt 100 pF gt 120 dB at dc gt 120 dBat de 50Hzor60Hz gt 60 dB at 50 gt B0dBat50Hzor60H
3. 1 0 2 1 8 mV mA Ar 400 0 1 2 2 5 1 0 2 1 8 mV mA 1 2 96 2 1 096 2 0 03 V A 45 Hz to 2 kHz 000R 10 00 A 12 2 10 2 0 03 V A 60 00 mA 0 4 96 4 0 2 4 1 8 mV mA 400 0 mA6 0 4 2 0 2 2 1 8 mV mA 0 2 4 0 03 V A 0 2 95 2 0 03 V A 12 2 5 1 0 2 100 uV uA y 1 0 2 100 uV uA 6 000 A 0 4 4 10 00 A 0 4 2 600 0 uA E 45 Hz to 2 kHz 6000 uA 129642 600 0 t 0 4 4 t 0 2 4 100 uV uA 6000 uA t 0 4 2 t 0 2 2 100 uV uA AC conversion for Model 83 is ac coupled and calibrated to the rms value of a sine wave input AC conversions for Model 87 are ac coupled true rms responding and valid from 3 to 100 of range except 400 mA range 5 to 100 of range and 10 A range 15 to 100 or range Model 87 is a true rms responding meter When the input leads are shorted together in the ac functions the Meter may display a residual reading between 1 and 30 counts A 30 count residual reading will cause only a 2 digit change for readings over 3 of range Using REL to offset this reading may produce a much larger constant error in later measurements 10 A continuous up to 35 C 20 minutes on 5 minutes off at 35 C to 55 C 20 A for 30 seconds maximum gt 10 A unspecified Below a reading of 200 counts add 10 counts 400 mA continuous 600 mA for 18 hrs maximum
4. Positive or negative slope indicator for Trigt Hz duty cycle triggering Pass Filter 87 KB The battery is low A A Warning avoid false readings which could lead to 02 possible electric shock personal injury replace the battery as soon as the battery indicator appears The continuity beeperison The continuity beeper is on Relative REL mode is active Smoothing is active 80 Series V Getting Started Manual Table 5 Display Features cont Amperes amps Microamp Milliamp Volts Millivolts Microfarad Nanofarad Nanosiemens Percent Used for duty cycle measurements O MO Ohm Megohm Kilohm Hz kHz Hertz Kilohertz AC DC Alternating current direct current C F Degrees Celsius Degrees Fahrenheit 610000 mV Displays selected range HiR The Meter is in high resolution Ines Hi Res mode HiRes 19 999 The Meter is in autorange mode and Auto automatically selects the range with the best resolution The Meter is in manual range mode 10 The number of segments is relative to the full scale value of the selected range In normal operation 0 zero is on the left The polarity indicator at the left of the graph indicates the polarity of the input The graph does not operate with the capacitance frequency counter functions temperature or peak min max For more information See Bar Graph in the Users Manual located
5. 1010 1 2004 e UL610101 1 Measurement Category III 1000V Pollution Degree 2 Measurement Category IV 600V Pollution Degree 2 Multimeters Introduction In this manual a Warning identifies conditions and actions that pose hazards to the user A Caution identifies conditions and actions that may damage the Meter or the equipment under test Electrical symbols used on the Meter and in this manual are explained in Table 1 A AWarning To avoid possible electric shock or personal injury follow these guidelines Use this Meter only as specified in this manual or the protection provided by the Meter might be impaired Do not use the Meter if it is damaged Before you use the Meter inspect the case Look for cracks or missing plastic Pay particular attention to the insulation surrounding the connectors Make sure the battery door is closed and latched before operating the Meter Replace the battery as soon as the battery indicator E appears Remove test leads from the Meter before opening the battery door Inspect the test leads for damaged insulation or exposed metal Check the test leads for continuity Replace damaged test leads before you use the Meter Do not apply more than the rated voltage as marked on the Meter between the terminals or between any terminal and earth ground 80 Series V Getting Started Manual Never operate the Meter with the cover removed or the case open Use caut
6. on the 80 Series V User Manual CD The bar graph also has a zoom function as described under Zoom Mode Overload condition is detected Display Messages Replace the battery immediately dst In the capacitance function too much electrical charge is i present on the capacitor being tested EEPr Err Invalid EEPROM data Have Meter serviced CAL Err Invalid calibration data Calibrate Meter LEAd ANTest lead alert Displayed when the test leads are in the A or mA uA terminal and the selected rotary switch position does not correspond to the terminal being used Invalid model Have Meter serviced ram Open thermocouple is detected Power Up Options Holding a button down while turning the Meter on activates a power up option Table 4 includes the power up options Automatic Power Off The Meter automatically turns off if you do not turn the rotary switch or press a button for 30 minutes If MIN MAX Recording is enabled the Meter will not power off To disable automatic power off refer to Table 4 Input Alert Feature If a test lead is plugged into the mA uA or A terminal but the rotary switch is not set to the correct current position the beeper warns you by making a chirping sound and the display flashes t EAd This warning is intended to stop you from attempting to measure voltage continuity resistance capacitance or diode values when the leads are plugged into a current terminal A Ca
7. ranges available for the selected function To return to autoranging hold the button down for 1 position second mv Switches between C and F Power up Enables the Meter s smoothing feature The Meter reads S until is released Multimeters The Meter s Features Table 4 Pushbuttons cont Switch Position Any switch position MIN MAX recording Frequency counter Power up Any switch position Continuity node MIN MAX recording Hz Duty Cycle Power up AutoHOLD formerly TouchHold captures the present reading on the display When a new stable reading is detected the Meter beeps and displays the new reading Stops and starts recording without erasing recorded values Stops and starts the frequency counter Turns on all LCD segments Turns the backlight on makes it brighter and turns it off For Model 87 hold down for second to enter the HiRes digit mode The HiRes icon appears on the display To return to the 3 1 2 digit mode hold down for one second HiRes 19 999 Turns the continuity beeper on and off Switches between Peak 250 us and Normal 100 ms response times Toggles the meter to trigger on positive or negative slope Disables the beeper for all functions The Meter reads bE E P until is released 80 Series V Getting Started Manual Table 4 Pushbuttons cont switch position C Fm REL A Rel
8. specified accuracy C lt 18 C or gt 28 C Electromagnetic Compatibility In an RF field of 3 V m total accuracy specified accuracy 20 counts Except 600 dc range total accuracy specified accuracy 60 counts Temperature not specified Relative Humidity 0 to 90 0 to 35 C 0 to 70 35 C to 55 C Battery Type 9 V zinc NEDA 1604 or 6F22 or 006 Battery Life 400 hrs typical with alkaline with backlight off Vibration Per MIL PRF 28800 for a Class 2 instrument Shock 1 Meter drop per IEC 61010 1 2001 Size HxWxL 1 25 in x 3 41 in x 7 35 in 3 1 cm x 8 6 cm x 18 6 cm Size with Holster and Flex Stand 2 06 in x 3 86 in x 7 93 in 5 2 cm x 9 8 cm x 20 1 cm Weight 12 5 0z 355 g Weight with Holster and Flex Stand 22 0 oz 624 g Safety Complies with ANSI ISA 82 01 2004 CSA 22 2 No 1010 1 2004 to 1000 V Overvoltage Category III IEC 664 to 600 V Overvoltage Category IV UL listed to UL61010 1 Licensed by TUV to EN61010 1 IP Rating 30 14 Multimeters Specifications Detailed Specifications For all detailed specifications Accuracy is given as of reading number of least significant digits at 18 C to 28 C with relative humidity up to 90 for a period of one year after calibration For Model 87 in the 4 digit mode multiply the number of least significant digits counts by 10 AC conversions are ac coupled and valid from 3 to 100 of range Model 87 is true r
9. FLUKE 80 Series V Multimeters Getting Started Manual PN 2101973 May 2004 Rev 2 11 08 2004 2008 Fluke Corporation All rights reserved Printed in U S A Specifications are subject to change without notice All product names are trademarks of their respective companies Lifetime Limited Warranty Each Fluke 20 70 80 170 and 180 Series DMM will be free from defects in material and workmanship for its lifetime As used herein lifetime is defined as seven years after Fluke discontinues manufacturing the product but the warranty period shall be at least ten years from the date of purchase This warranty does not cover fuses disposable batteries damage from neglect misuse contamination alteration accident or abnormal conditions of operation or handling including failures caused by use outside of the product s specifications or normal wear and tear of mechanical components This warranty covers the original purchaser only and is not transferable For ten years from the date of purchase this warranty also covers the LCD Thereafter for the lifetime of the DMM Fluke will replace the LCD for a fee based on then current component acquisition costs To establish original ownership and prove date of purchase please complete and return the registration card accompanying the product or register your product on http www fluke com Fluke will at its option repair at no charge replace or refund the purchase price of a defe
10. ative mode Any switch position Power up Any switch position except diode test Power up Stores the present reading as a reference for subsequent readings The display is zeroed and the stored reading is subtracted from all subsequent readings Enables zoom mode for the bar graph Refer to Zoom Mode in the Users Manual located on the 80 Series V User Manuals CD The Meter reads Or L until is released Press for frequency measurements Starts the frequency counter Press again to enter duty cycle mode Enables the Meter s high impedance mode when the mV dc function is used The Meter reads Hi until is released Multimeters The Meter s Features Indicates negative readings In relative mode this sign indicates that the present input is less than the stored reference Indicates the presence of a high voltage input Appears if the input voltage is 30 V or greater ac or dc Also appears in low pass filter mode Also appears in cal Hz and duty cycle modes AutoHOLD is active Display Hold is active 610000 mV q Po is le aomt_af eps Indicates the Meter is in Peak Min Max Figure 1 Display Features Model 87 9 mode and the response time is 250 87 only Table 5 Display Features MIN MAX Indicators for minimum maximum MAX MIN recording mode AVG 9 Polarity indicator for the analog bar graph Low pass filter mode 87 only See Low
11. ctive product purchased through a Fluke authorized sales outlet and at the applicable international price Fluke reserves the right to charge for importation costs of repair replacement parts if the product purchased in one country is sent for repair elsewhere If the product is defective contact your nearest Fluke authorized service center to obtain return authorization information then send the product to that service center with a description of the difficulty postage and insurance prepaid FOB Destination Fluke assumes no risk for damage in transit Fluke will pay return transportation for product repaired or replaced in warranty Before making any non warranty repair Fluke will estimate cost and obtain authorization then invoice you for repair and return transportation THIS WARRANTY IS YOUR ONLY REMEDY NO OTHER WARRANTIES SUCH AS FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSED OR IMPLIED FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA ARISING FROM ANY CAUSE OR THEORY AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON FLUKE S BEHALF Since some states do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages this limitation of liability may not apply to you If any provision of this warranty is held invalid or unenforceable by a court or other decision maker of competent jurisdiction such hold
12. ecified 1 Below a reading of 200 counts add 10 counts 2 Frequency range 1 kHz to 2 5 kHz 16 Table 9 DC Voltage Resistance and Conductance Function Specifications Model 83 Model 87 0 1 1 0 1 1 0 1 1 600 0 Q 6 000 kQ 60 00 kQ 600 0 kQ 6 000 MQ Resolution 010 0 001 kQ 0 01 kQ 0 1 kQ 0 001 MQ 0 1 1 0 4 2 0 4 1 t 0 7 1 Multimeters Specifications 0 05 1 0 05 1 0 05 1 E 0 05 1 0 2 2 0 2 1 0 6 1 0 4 1 0 7 1 E E E H oH Hon 0 2 1 0 6 1 1 0 3 1 0 10 50 00 MQ 0 01 MQ 60 00 nS 0 01 nS 1 When using the REL A function to compensate for offsets 2 Add 0 5 of reading when measuring above 30 MQ in the 50 MQ range and 20 counts below 33 nS in the 60 nS range 1 0 3 1 0 10 Table 10 Temperature Specifications 87 Only 200 C to 1090 C 0 1 1 10 328 F to 1994 F 0 1 F 1 18 1 Does not include error of the thermocouple probe 2 Accuracy specification assumes ambient temperature stable to 1 C For ambient temperature changes of 5 C rated accuracy applies after 1 hour 17 80 Series V Getting Started Manual Table 11 Current Function Specifications Accurac Range Resolution y Burden Voltage Model 83 Model 872 3 typical mA 60 00 mA 1 2 2
13. ifications 87 Only sess enne eene Current Function 1 nennen nennen Capacitance and Diode Function Specifications essen Frequency Counter Specifications essen Frequency Counter Sensitivity and Trigger Levels ssseeenn Electrical Characteristics of the Terminals MIN MAX Recording Specifications sess Display Features Model 87 nnne nenne neret nennen enne Low It cadccee iii 80 Series V Getting Started Manual Introduction AA Warning Read Safety Information before you use the Meter Except where noted the descriptions and instructions in this manual apply to Series V Models 83 and 87 multimeters hereafter referred to as the Meter Model 87 appears in all illustrations Contacting Fluke To contact Fluke call one of the following telephone numbers USA 1 888 44 FLUKE 1 888 443 5853 Canada 1 800 36 FLUKE 1 800 363 5853 Europe 31 402 675 200 Japan 81 3 3434 0181 Singapore 65 738 5655 Anywhere in the world 1 425 446 5500 USA Service 1 888 99 FLUKE 1 888 993 5853 Or visit Fluke s Web site at www fluke com To register your product visit register fluke com Safety Information The Meter complies with e EN61010 1 2001 e ANSI ISA S82 01 2004 e C22 2 No
14. ing will not affect the validity or enforceability of any other provision Fluke Corporation Fluke Europe B V P O Box 9090 P O Box 1186 Everett WA 5602 B D Eindhoven 2 02 98206 9090 The Netherlands Table of Contents Title Page O Contacting Fluke sess rn Safety Information uie iiie an en ie The Meter s Features Power Up Options anne ala Automatic Power Off Input Alert SO CA LOW Pass Filter 87 SEIRET Ol UEA E an aan nen end kann AutoHOLD Me ttt ttt ttt Relative Mode RREEIMMMMM Maintenance isos sis He A a eee General Maintenance ccccsccceceeseeeeeeneeeeesneeeseaeeeesceeeeesueeeseaeeeescsaeeeeesneeeessneeess gi Wc E esha aa Specifications d Detailed Specifications 80 Series V Getting Started Manual Table ON ON Figure List of Tables Title Page Display MIN MAX SAA Model 87 AC Voltage Function Model 83 AC Voltage Function DC Voltage Resistance and Conductance Function Specifications Temperature Spec
15. ion when working with voltages above 30 V ac rms 42 V ac peak or 60 V de These voltages pose a shock hazard Use only the replacement fuses specified by the manual Use the proper terminals function and range for measurements Avoid working alone When measuring current turn off circuit power before connecting the Meter in the circuit Remember to place the Meter in series with the circuit When making electrical connections connect the common test lead before connecting the live test lead when disconnecting disconnect the live test lead before disconnecting the common test lead Do not use the Meter if it operates abnormally Protection may be impaired When in doubt have the Meter serviced Do not operate the Meter around explosive gas vapor or dust Use only a single 9 V battery properly installed in the Meter case to power the Meter When servicing the Meter use only specified replacement parts When using probes keep fingers behind the finger guards on the probes Do not use the Low Pass Filter option to verify the presence of hazardous voltages Voltages greater than what is indicated may be present First make a voltage measurement without the filter to detect the possible presence of hazardous voltage Then select the filter function A Caution To avoid possible damage to the Meter or to the equipment under test follow these guidelines Disconnect circuit power and discharge all high vo
16. ltage capacitors before testing resistance continuity diodes or capacitance Use the proper terminals function and range for all measurements Before measuring current check the Meter s fuses See Fuse Test in the Users Manual on the 80 Series V User Manual CD Multimeters Safety Information Table 1 Electrical Symbols installations such as distribution panels feeders and short branch circuits and lighting systems in large buildings Inspected and licensed by T V Product Services underground utility service c IEC Overvoltage Category III IEC Overvoltage Category IV CAT III equipment is designed to protect against CAT CAT IV equipment is designed to protect against transients from the transients in equipment in fixed equipment IV primary supply level such as an electricity meter or an overhead or 80 Series V Getting Started Manual The Meter s Features Tables 2 through 5 briefly describe the Meter s features Table 2 Inputs Terminal Description A Input for 0 A to 10 00 A current 20 A overload for 30 seconds maximum current frequency and duty cycle measurements mA LA Input for O uA to 400 mA current measurements 600 mA for 18 hrs and current frequency and duty cycle COM Return terminal for all measurements 1 V Q gt Input for voltage continuity resistance diode capacitance frequency temperature 87 and duty cycle measurements Multi
17. meters The Meter s Features Table 3 Rotary Switch Positions Switch Position Any Position When the Meter is turned on the Meter model number briefly appears on the display AC voltage measurement Press ___ for low pass filter fra 87 only DC voltage measurement Ua 600 mV dc voltage range m Press gt for temperature B 87 only Ae Press for continuity test Resistance measurement Press ___ for Capacitance measurement mA AC current measurements from 0 mA to 10 00 A A Press ___ for de current measurements from 0 mA to 10 00 AC current measurements from 0 uA to 6000 pA H Press ___ for de current measurements from 0 pA to 6000 uA 80 Series V Getting Started Manual Table 4 Pushbuttons Switch Position am Qe Selects capacitance Selects temperature 87 only Selects ac low pass filter function 87 only Switches between dc and ac current Switches between dc and ac current Disables automatic power off feature Meter normally powers off in 30 minutes The Meter reads PoFF until CD is released Any switch Starts recording of minimum and maximum values Steps the display through MAX MIN AVG average and present position readings Cancels MIN MAX hold for 1 second Power up Enables the Meter s calibration mode and prompts for a password The Meter reads AL and enters calibration mode See the 80 Series V Service Information Any switch Switches between the
18. ms responding AC crest factor can be up to 3 at full scale 6 at half scale For non sinusoidal wave forms add 2 Rdg 2 full scale typical for a crest factor up to 3 Table 7 Model 87 AC Voltage Function Specifications Function Range Resolution Accuracy ooo 45 65Hz 30 200Hz 200 440Hz 440Hz 1khz 1 5 5 20kH y 600 0 mV 0 1 mV 0 7 4 6 000 V 0 001 V 20 4 2 0 20 00 V 01V 1 0 4 07 42 0054 600 0 V 0 1V 2 0 4 unspecified 1000 V 1V unspecified unspecified Same as 1 4 Low pas filter pu d 1 09644 j 4 pe unspecified unspecified Below 10 96 of range add 12 counts The Meter is a true rms responding meter When the input leads are shorted together in the ac functions the Meter may display a residual reading between 1 and 30 counts A 30 count residual reading will cause only a 2 digit change for readings over 3 96 of range Using REL to offset this reading may produce a much larger constant error in later measurements Frequency range 1 kHz to 2 5 kHz A residual reading of up to 13 digits with leads shorted will not affect stated accuracy above 3 of range Specification increases from 1 at 200 Hz to 6 at 440 Hz when filter is in use 15 80 Series V Getting Started Manual Table 8 Model 83 AC Voltage Function Specifications Function Range Resolution Accuracy 600 0 mV 6 000 V 60 00 V 600 0 V 1000 V 0 j unsp
19. s or 250 us response time The 250 us response time is indicated by amp 2 9 on the display Stored values are erased The present and AVG average values are not available when 250 us is selected Stop recording without erasing stored values Press again to resume recording Exit MIN MAX mode Stored values are erased The Meter stays in the selected range AutoHOLD Mode A AWarning To avoid electrical shock or personal injury do not use AutoHOLD mode to determine that circuits are without power The AutoHOLD mode will not capture unstable or noisy readings The AutoHOLD mode captures the present reading on the display When a new stable reading is detected the Meter beeps and displays the new reading To enter or exit AutoHOLD mode press oc Relative Mode Selecting relative mode causes the Meter to zero the display and store the present reading as the reference for subsequent measurements The Meter is locked into the range selected when you pressed Press again to exit this mode In relative mode the reading shown is always the difference between the present reading and the stored reference value For example if the stored reference value is 15 00 V and the present reading is 14 10 V the display shows 0 90 V Multimeters AutoHOLD Mode Maintenance A AWarning To avoid electrical shock or personal injury repairs or servicing not covered in this manual should be performed onl
20. ution Placing the probes across in parallel with a powered circuit when a lead is plugged into a current terminal can damage the circuit you are testing and blow the Meter s fuse This can happen because the resistance through the Meter s current terminals is very low so the Meter acts like a short circuit Multimeters The Meter s Features Low Pass Filter 87 The 87 is equipped with an ac low pass filter When measuring ac voltage or ac frequency press to activate the low pass filter mode 63 The Meter continues measuring in the chosen ac mode but now the signal diverts through a filter that blocks unwanted voltages above 1 kHz refer to Figure 2 The lower frequency voltages pass with reduced accuracy to the measurement below 1 kHz The low pass filter can improve measurement performance on composite sine waves that are typically generated by inverters and variable frequency motor drives A AWarning To avoid possible electric shock or personal injury do not use the Low Pass Filter option to verify the presence of hazardous voltages Voltages greater than what is indicated may be present First make a voltage measurement without the filter to detect the possible presence of hazardous voltage Then select the filter function Note In Low Pass Mode the Meter goes to manual mode Select ranges by pressing the RANGE button Autoranging is not available in Low Pass Mode MM EN Os 100 Hz 1 kHz
21. y by qualified personnel as described in the 80 Series V Service Information General Maintenance Periodically wipe the case with a damp cloth and mild detergent Do not use abrasives or solvents Fuse Test If a test lead is plugged into the mA uA or A terminal and the rotary switch is turned to a non current function the Meter chirps and flashes LEAd if the fuse associated with that current terminal is good If the Meter does not chirp or flash L EAd the fuse is bad and must be replaced A AWarning To avoid electrical shock or personal injury remove the test leads and any input signals before replacing the battery or fuses To prevent damage or injury install ONLY specified replacement fuses with the amperage voltage and speed ratings shown in Replacement Parts in the Users Manual located on the 80 Series V User Manual CD 13 80 Series V Getting Started Manual Specifications Maximum Voltage between any Terminal and Earth Ground 1000 V rms A Fuse Protection for mA or yA inputs 44 100 A 1000 V FAST Fuse A Fuse Protection for A input 11 A 1000 V FAST Fuse Display Digital 6000 counts updates 4 sec Model 87 also has 19 999 counts in high resolution mode Analog Bargraph 33 segments updates 40 sec Frequency 19 999 counts updates 3 sec at gt 10 Hz Temperature Operating 20 C to 55 C Storage 40 C to 60 C Altitude Operating 2000 m Storage 10 000 m Temperature Coefficient 0 05 x
22. z EN 1000 Vrms 10MQ lt 100pF gt 120dBat de 50 Hz or 60 Hz gt 60 dB at 50 Hz or 60 Hz 1000 V rms 0 lt 100 pF gt 60 dB de to 60 Hz ac coupled Open Circuit Full FullScale Voltage FullScale Voltage Typical Short Circuit Current Test Voltage To 6 0 50 MQ or 600 Q 60 nS 1000 V rms lt 7 9V de 41V dc lt 45Vdo fioopa 104A ima fina 05A 1000 V rms 79V dc 3 000 V dc 1 0 mA typical 1 109 V Hz max Table 16 MIN MAX Recording Specifications Nominal Response 83 100 ms to 80 Specified accuracy 12 counts for changes gt 200 ms in duration 40 counts in ac with beeper on 100 ms to 80 en accuracy 12 counts for changes gt 200 ms in duration dc functions 120 ms to 80 Specified accuracy 40 counts for changes gt 350 ms and inputs gt 25 of range ac functions 250 us peak Specified accuracy 100 counts for changes gt 250 us in duration Model 87 only add 100 counts for readings over 6000 counts add 100 counts for readings in Low Pass mode 1 For repetitive peaks 1 ms for single events 21 80 Series V Getting Started Manual 22
Download Pdf Manuals
Related Search