Home

2DScan FX100 Barcode Scanner Scanner User`s Manual

1. Code Programming OFF Load Standard 25 Factory Default Pro CMD 0418000 Fnable Disable Standard 25 Enable Standard 25 Pro CMD 0418020 Disable Standard 25 Pro CMD 0418010 a Page 89 Symbols SK Tools Code Programming ON Select Message Length It is used to program the valid reading length of Standard 25 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Standard 25 Message Length is defined by Min Message Length and gramming OFF Code Pro Max Message Length Min Message Length default 6 Pro CMD 0418030 Max Message Length default 48 Pro CMD 0418040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of Standard 25 to 8 bytes and Max Message Length to 12 Ki le na Page 90 Symbols Standard 25 Tools Check Digit Standar
2. Prefix Sequences Biter TT Ra HSuffix Terminal AIMID CodeID User Prefix User Suffix Terminal i o or 1 1 a Page 140 Interception Pack Appendix Factory Default List Parameters Factory Default Symbol Code 128 Enable Max Message Length gt lt O A av ga O ES ga EAN 8 Enable 5 2 Digits Addenda Code 5 Digits Addenda Code B cul Me Mel OA JEJEJE E IS e o o E o O wlx x gt z bes Z de pa ud Q EAN 13 Enable O Embe Ya OOO Send Check Digit On o po Enable 2 Digits Addenda Code om ce Ei 2 Digits Addenda Code 5 Digits Addenda Code C E Enable secs 5 l B 2 Digits Addenda Code 5 Digits Addenda Code A Send Default 0 UPC A Enable Send Check Digit Enable 2 Digits Addenda Code Enable 5 Digits Addenda Code Send Default 0 Interleaved 2 of 5 Enable Check Send Check Digit mimimuiu 3 E i e E SE e BE le lo lO a o O e L L IS HR da 5 Max Message Length a Page 141 Appendix Factory Default List Emb o e inte mw Send ANO Ge ow a Page 142 Appendix Factory Default List EAN UCC Composite Off Min Message Length No less than 4 nG Page 143 Appendix Factory Default List PDF417 fraen Read Single PDF417 Only On a Page 144 Appendix A
3. Enable Maxicode Pro CMD 0505020 Disable Maxicode Pro CMD 0505010 me Page 112 Symbols Maxicode NA Tools Code Programming ON Select Message Length It is used to program the valid reading length of Maxicode The engine will not send l barcode message to the Host 1f the decoded data length does not match the valid reading length Maxicode Message Length is defined by Min Message Length and Max Code Programming OFF Message Length li Min Message Length default 1 Pro CMD 0505030 Max Message Length default 150 Pro CMD 0505040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length Maxicode Please program Max amp Min Message Length to the same value To set Min Message Length of Maxicode to 8 bytes and Max Message Length to 12 bytes read these programming codes 1 Code Programming ON 2 Select Min Message Length 3 Digit Code 8 see Digit Code 4 Save Programming see Digit Code 5 Select Max Message Length 6 Digit Code 1 7 Digit Code 2 8 Save Programming 9 Code Programming OFF nG Page 113 Symbols Chinese Sensible Code d Tools MT Code Programming ON Load Factory Default Code Programming OFF Load Chinese Sensible Code Factory Default Pro CMD 0508000 Enable Disable Chinese Sensi
4. is enabled and barcode message length minus one is less than Min Message Length it will lead to an error E g Reading a 4 byte include check byte MSI Plessey with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error Symbols Tools Code Programming ON Load Factory Default l Code Programming OFF Load PDF417 Factory MU Pro CMD 0501000 Enable Disable PDF417 Enable PDF417 Pro CMD 0501020 Disable PDF417 Pro CMD 0501010 oa Page 98 Symbols NA Tools Select Message Length It is used to program the valid reading length of PDF417 The engine will not send barcode message to the Host if the decoded data length does not match the valid reading length PDF417 Message Length is defined by Min Message Length and Max Message Code Programming Length Min Message Length default 1 Pro CMD 0501030 ple Max Message Length default 2710 Pro CMD 0501040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length PDF417 Please program Max Min Message Length to the same value To set Min Message Length of PDF417 to 8 bytes and Max Message Length to 12 bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code SelectMax Messa
5. a Page 128 Message Interception amp Pack Tools Code Programming ON Interception Rule No 1 It only intercepts selected symbols raw barcode messages and it effects all barcodes of the barcode format Interception Rule No 2 There are maximum 3 interception options restored in the non volatile memory If more than 3 are programmed the last 3 are stored For example if there are 4 options are programmed in the order of Code 128 Code 39 QR Code and UPC A and Save The 3 options are restored gt ra LLE in the order of Code 39 QR Code UPC A Interception Rule No 3 If there are more than one options programmed for a barcode format the later one is used For example there are 3 options restored Code 128 option A QR Code option Code 128 option B The Code 128 option B is used when a Code 128 barcode is read Enable Interception barcode should be read before intercepting message Steps should be followed to erase certain barcode EAN 13 e g interception options 1 Read Erase Certain Barcode Interception Options barcode 2 Get Symbol ID for example EAN 13 005 3 Read digit codes accordingly 4 Read Save barcode Disable Interception Pro CMD 0315000 Frase Certain Barcode Interception Options Pro CMD 0316010 Enable Interception Pro CMD 0315010 Frase Latest Interception Options Pro CMD 0316020 Program Intercept Option Pro CMD 0316000 Erase All Interception
6. 0 50 100 150 200 250 a Page 9 Getting to Start Performance Image Sensor CMOS Resolution 752 480 Interface RS232 USB 1 1 PDF417 QR Code Model 1 2 2D DataMatrix ECC200 ECC000 050 080 100 140 Aztec Maxicode Symbologies Ro ID Code128 EAN 13 EAN 8 Code39 UPC A UPC E Codabar Interleaved 2 of 5 ISBN ISSN Code 93 etc Precision gt Smil CMOS Acquisition 60 fps Light Source LED 617 5 nm 633 5 nm Light Intensity 320 LUX 130 mm Depth of Scan Field 35mm 210 mm Print Contrast Signal gt 30 Roll 360 0 Pitchand0 Skew EO bul 60 0 Rolland 0 Skew Skew 60 0 Rolland 0 Pitch Mechanical Electricals Power Consumption 2 1W Voltage DC 5 0V Max 420 mA Current Working 260 mA Idle l mA Weight 70g Environment Operate Temperature 5 C 445 C Storage Temperature 40 C 60 C Humidity Certificates 5 95 non condensing FCC Part15 Class B CE EMC Class B Test Condition Code39 4 Bytes Resolution 10mil W N 3 1 PCS 1 0 Barcode Height 12mm Distance 100mm T 23 C Illumination 200 LUX nG Page 10 Getting to Start Dimensions of FX100 Unit UU 97 M3 machine skew 11 7mm WE 3 3 4 A Y d NA Imm 1 10mm 60mm Figure 1 FX100 Top View a Page 11 Programming the Engine Introduction There are 3 ways to program configure the Engine Code Programming Command Pro
7. Check DISI TTT TTT E o o EU O 84 DIANA o E O PO ANNA E E E OE AA 85 Load Fa ctory AA AA APA PAA 83 Enable Disable ISBN Mc m 85 LI RAR RR AA 85 E ORE RR ERRE AA AA 86 Load Factory TOS TUG RR RR RO teia dd 86 Enable Disable Industrial EE 86 Select Message Length E 87 CID 88 musa aan a 89 Load Paetory RE virile een adicta 89 Enable Disable Standard E 89 Select Message GNG luso AGNO NDN la 90 CREDO e 9 A EEE 92 Load Factory Dealer ita 92 Enable Disable Plessey iii 92 Select Messaje E E 93 Check PIS E 94 N E A A E DAA NOO 95 EE l TT To I LJ TT oR ETT 95 Enable Disable EE saanman Kad A Kon ka KR AN 95 Select Message Length unionista rapa rile 96 rcv bou EN 97 e RPP PEO E PE E GO Po e E RR 98 Load Tacto Det ella AA 98 Enable Disable PDP4 usos iii 98 Select Message DEBET np aaa eripi EE Rectum Rt dA dU pha Mead 99 JDI ITAN A ia 100 Forward Backwrd Direction PDF EE 100 Table of Contents ORC Ode AA A AG 101 Load Factory Re E OS PO PO E O RR RD AROS ERR SR 101 Enable Disable Eed 101 Select Message Length a ta TETTE 102 CRI 103 LV RR EZRA 104 Load Factory DEU astas ori 104 Enable Disable e va icio MNT 104 Select Message Lens 105 Reading Multi barcodes of an Image 106 The number of Multi barcodes Lakan NAGA AA AA 107 BEE ee AI 108 Lead Factory PA 108 Enable Disable Data Mat quoi LU iia 108 Select Message Lenta iaa 109 Data Matrix Twin Code unan Aka 110 RECARE R
8. Stop Character Codabar uses either one of A B C and D as the start character and the stop character Transmission of them can be selected Code Programming OFF Transmit Both Start amp Stop Character Pro CMD 0409090 Transmit Neither Start amp Stop Character Pro CMD 0409080 Use ABCD ABCD As Start amp Stop Character Pro CMD 0409100 Use Upper Letter Pro CMD 0409120 Use ABCD TN E As Start amp Stop Character Pro CMD 0409110 Use Lower Letter Pro CMD 0409130 C Page 75 Symbols R Tools Code Programming ON Load Factory Default l Code Programming OFF Load Code 93 Factory Default Pro CMD 0410000 NA Enable Disable Code 93 Disable Code 93 Pro CMD 0410010 Enable Code 93 Pro CMD 0410020 na Page 76 Symbols R Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 93 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code 93 Message Length is defined by Min Message Length and Max gramming OFF Code Pro n Min Message Length default 1 Pro CMD 0410030 Max Message Length default 48 Pro CMD 0410040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two wA lengths If Max Mess
9. default 48 Pro CMD 0420040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of MSI Plessey to 8 bytes and Max Message Length to 12 E le 90 Q9 tM na Page 96 Symbols MSI Plessey ss Tools Code Programming ON Check Digit Plessey may include Check Digits s not compulsory following its barcode message It may have one or two digits which verify the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digits gramming OFF Code Pro NO Check Transmit All Pro CMD 0420050 Double Check Digits MOD10 MOD11 Pro CMD 0420080 Single Check Digit MODIO Pro CMD 0420060 NO Transmit Check Digits Pro CMD 0420090 Double Check Digits MOD10 MOD10 Pro CMD 0420070 Transmit Check Digits Pro CMD 0420100 When Check Do not Transmit Check digit
10. CMD 0100030 1200 9600 19200 Pro CMD 01000501 Pro CMD 0100000 38400 Pro CMD 0100060 2400 Pro CMD 0100010 57600 Pro CMD 0100070 4800 Pro CMD 0100020 115200 Pro CMD 0100080 14400 Pro CMD 0100040 a Page 26 RS232 Interface Serial Port NA Tools Code Programming ON Parity Check Parity check options should be the same on the engine and the Host Select Odd parity If data has an odd number of 1 bits the parity bit value is set to 0 f Code Programming OFF Select Even parity If data has an even number of 1 bits the parity bit value is set to 0 Select No Parity Check and parity bit will not be sent No Parity Check Pro CMD 0101000 Odd Check Pro CMD 0101020 Even Check Pro CMD 0101010 Hardware Auto Flow Control When enabled the engine will decide if the data should be sent in accordance with CTS signal level When it is low level CTS signal it means the serial port s cache memory of receiving end such as PC is full and the engine will not send data through RS232 until CTS signal is set to high level by receiving end When the engine is not ready for receiving it will set RTS signal to low level When sending end such as PC detects it it could not send data to the engine any more otherwise the data will be lost When disabled data s sending and receiving through serial port will not be effected by RTS CTS signal Disabl
11. Default 0 The first byte of UPC E is defaultto 0 Code Programming OFF Do Not Transmit 0 Pro CMD 0403090 Transmit 0 Pro CMD 0403100 UPC E Expand to UPC A Follow the standard algorithm to expand UPC E to UPC A Do Not Expand to UPC A Pro CMD 0403110 Expand to UPC A Pro CMD 0403120 a Page 56 Symbols Tools uz Code Programming ON Load Factory Default I Load UPC A Factory Default Pro CMD 0404000 TI OFF Disable Enable UPC A xx Enable UPC A Pro CMD 0404020 Disable UPC A Pro CMD 0404010 Check Digit UPC A is fixed 13 digits barcode and the last digit is Check Digit Transmit Check Pro CMD 0404040 Do Not Transmit Check Pro CMD 0404030 a Page 57 Symbols PUPC 4 fll XX Tools o Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 2 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 2 digits Addenda Code Code Programming OFF uic AA mO vu i SEIKO 1 Disable 2 Digits Addenda Code Pro CMD 0404050 Enable 2 Digits Addenda Code Pro CMD 0404060 5 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 5 digits Addenda Code The left one in blue lines is an ordinary code The right one in red
12. Options Pro CMD 0316030 a Page 129 Message Interception amp Pack Message Interception d Tools Code Programming ON Programming 1D Intercept Option l When programming ID intercept option read digit codes as interception command The rules is as below The interception command format of ID interception command regards a 3 digit decimal number as a unit j TII OFF The interception command has two parts which are barcode type part Symbol ID and data interception part A command could have several data interception parts A barcode type part Symbol ID uses a unit such as 005 a datainterception part uses three units including intercepting direction unit 000 Ascending or 001 Descending start unit and stop unit There is only one type of barcode to be setted to intercept in a time Intercept EAN 13 from Ist digit to 3rd ascending and from reciprocal 4th to reciprocal Ist 1 Read Code Programming ON a 2 Read Allow Interception p 3 Read Program Intercept Option 4 Check Symbols ID Number table for EAN 13 5 Read below digit barcodes ii e ow sor oss ou ow en symbol ID the Ist digit the 3rd digit the 4th digit the Ist digit Barcode Type Data Interception 1 Data Interception 2 Note 1 Maximum sections of barcode message interception are 5 2 Maximum value is 127 for both start digital and end digital 3 Overlaps of barcode message sections
13. are allowed and work independently 4 Start unit and end unit determine its message section In the above example descending 004 and 001 means the section of last 4th last 3rd last 2nd and last one digits 5 To intercept only one digit program start unit and end unit to be the same value a Page 130 Message Interception amp Pack R Tools Code Programming ON Programming 2D Intercept Option When programming 2D intercept option read digit codes as interception command The rules is as below The interception command has two parts which are barcode type part Symbol ID and data interception part A command could have several data Code Programming OFF interception parts A barcode type part Symbol ID uses a unit such as 005 a data interception part uses three units including intercepting direction unit 000 Ascending or 001 Descending start unit and stop unit Barcode type part and intercepting direction regards a 3 digit decimal number as a unit but start and stop digit regards a 6 digit decimal number as a unit They uses 6 digits to present 4 digit value The first two digits are for thousandth and next two digits for hundredth For example 001013 means 113 Thereis only one type of barcode to be setted to intercept in a time For example intercept QR Code from Ist digit to 20th ascending and from 113th digit to 140th ascending I
14. barcode message l It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digit o Code Programming OFF Check Do Not Transmit Check Digit means to read and check If verifica tion is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0415050 Single Check Digit MOD11 Len lt 10 Double Check Digits MOD11 MOD11 Len 10 Pro CMD 0415090 Single Check Digit MODII Pro CMD 0415060 Single Check Digit MOD11 Len lt 10 Double Check Digits MOD11 MOD9 Len gt 10 Pro CMD 0415100 Double Check Digits MODII MODII Pro CMD 0415070 Do not transmit Check Digit Pro CMD 0415110 Double Check Digits MOD11 MOD9 Pro CMD 0415080 Transmit Check Digit Pro CMD 0415120 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error V E g Reading a 4 byte include check byte Code 11 with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error Symbols XX Tools Code Programming ON 7 o B Load ISBN
15. be read more than once in the delay period 1f ambient illumination is changed for example the bar code is removed out of reading area and moved back Multi reading Semi prohibit Pro CMD 0313020 Multi reading Prohibit Pro CMD 0313030 To set One Reading Timeout to 1500ms read these programming codes 1 Code Programming ON E le SE 2 One Reading Timeout 3 Digit Code 1 5 0 0 see Digit Code 4 Save Programming a Page 20 Programming the Engine SK Tools ui Code Programming ON Sensitivity is how sensitive the engine is to ambient illumination change Sensitivity value is 1 20 The lower the sensitivity value is the higher sensitivity will be The low er the sensitivity value 1s the smaller illumination change will initiate reading Code Programming OFF High Sensitivity 8 Pro CMD 0312020 Enhanced Sensitivity 5 Pro CMD 0312030 Normal Sensitivity 11 Pro CMD 0312010 Program Sensitivity Min 1 Max 20 Pro CMD 0312040 Low Sensitivity 14 Pro CMD 0312000 a Page 21 Programming the Engine Exposure Imaging Mode NA Tools Code Programming ON Code Programming OFF Normal Exposure Mode Pro CMD 0321000 Reflections Eliminating Mode Pro CMD 0321010 a Page 22 Programming the Engine Default Tools Code Programming ON Factory Default Read Load All Factory Default
16. if then read Abort One Data of Current Setting the 3 will be deleted if read Code Programming OFF Abort One String of Current Setting the 123 will be deleted if read Abort Current Setting both the program code and 123 will be deleted the device will be on status of initiating program code Save Pro CMD 0000160 Abort Current Setting Pro CMD 0000190 Abort One Data of Current Setting Pro CMD 0000170 Abort One String of Current Setting Pro CMD 0000180 a Page 139 Appendix Factory Default List General Programming Code Programming om o 0 Illumination Illumination Wink o Aiming AimingWink On T Decoding Beep o n E Decoding Beep Type o ei Decoding Beep Volume ed LL ny n Working Mode O AutoMode 3000ms CC o Fail umm 1500ms Sensitivity Normal Exposure Mode Power On Send Product Info MM 4 Un O 5 a rg O Q o a O S O tr un S 2 9 Sela 8 n o I Du lo o g O R a O um B O Le a Ue 09 JE 5 B ga o lo lt e le O 3 Ox ga 2 o o lt Baud Rate Serial Port Check Transmit Digits Stop Digit Keystroke Delay Caps Lock Convert Case ic Keypad Unkown Character Beep Hardware Auto Flow Control Emulate ALT keypad Function Key Mapping Emulate Numeric Ke J ri 3 mi O GQ o B ga Add Prefix Suffix PS
17. lines is the 5 digits Addenda Code p des c e amd de eo We pp 23456 1134561789014 KO dee GG QU BA T Disable 5 Digits Addenda Code Pro CMD 0404070 Enable 5 Digits Addenda Code Pro CMD 0404080 Enable 2 Digits Addenda Code read an ordinary code and 2 digits Addenda Code Enable 5 Digits Addenda Code read an ordinary code and 5 digits Addenda Code Disable 2 Digits Addenda Code read an ordinary code only and ignore 2 digits Addenda Code Symbols XX Tools Code Programming ON Transmit Default 0 The first byte of UPC A is default to 0 l Code Programming OFF Do Not Transmit 0 Pro CMD 0404090 Transmit 0 Pro CMD 0404100 di UPC A has the default O but it is not printed out unlike UPC E Read Transmit i ASA 0 willadda 0 to transmit na Page 59 Symbols Interleaved 2 of 5 IS Tools eee Code Programming ON Load Factory Default I Code Programming OFF Load Interleaved 2 of 5 Factory Default Wi Pro CMD 0405000 Disable Enable Interleaved 2 of 5 Enable Interleaved 2 of 5 Pro CMD 0405020 Disable Interleaved 2 of 5 Pro CMD 0405010 When the engine can not read Interleaved 2 of 5 please read Enable Interleaved 2 of 5 and try again na Page 60 Symbols 2 of SK Tools Code Programming ON Select Message Length It is used to program the valid r
18. notation to disable the Code Programming 2 The second part of the notation is the name of the options or features such as Disable Code Pro gramming 3 The third part of the notation is the corresponding Pro CMD string of the Code Programming 4 Ifthereis in front of the name it means the notation is factory default a Page 13 Programming the Engine Code Programming On Off d Tools ming function One or more Code Programming barcodes can be read to configure the Engine If an option or feature needs additional parameters such as digits they can be found at the end of this chapter To exit Code Programming read Code Programming OFF or any normal Code Programming OFF barcode i Code Programming ON Read the Code Programming ON barcode to activate Code Program l 4 Code Programming OFF Pro CMD 0006000 Code Programming ON Pro CMD 0006010 The value of code programming can be sent to the Host For factory default No Send Pro Code Value the value of programming codes will not be sent to the Host by reading Send Pro Code Value the reader will send the value of Programming Code to the Host No Send Pro Code Value Pro CMD 0002000 Send Pro Code Value Pro CMD 0002010 a Page 14 Programming the Engine Tools Code Programming ON Illumination LED lighting up barcodes are used to capture better images There are 4 modes Illumination W
19. of Aztec to 8 bytes and Max Message Length to 12 bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF SA PO nG Page 105 Symbols SX Tools Reading Multi barcodes of an Image l There are three modes Mode l Read one barcode only Mode 2 Read fixed number of barcodes only Code Programming OFF Mode 3 Composite Reading Read fixed number of barcodes first if failed read one barcode only Mode 1 Pro CMD 0503070 Mode 2 Pro CMD 0503080 Mode 3 Pro CMD 0503090 na Page 106 Symbols XK Tools Code Programming ON The number of Multi barcodes l Code Programming OFF Pro CMD 0503060 5 Pro CMD 0503064 2 Pro CMD 0503061 6 Pro CMD 0503065 3 Pro CMD 0503062 7 Pro CMD 0503066 4 Pro CMD 0503063 8 Pro CMD 0503067 a Page 107 Symbols Tools eee Code Programming ON Load Factory Default d Load Data Matrix Factory Default Pro CMD 0504000 Enable Disable Data Matrix Enable Data Matrix Pro CMD 0504020 Disable Data Matrix Pro CMD 0504010 When the engine can not read Data Matrix please read Enable Data Matrix and try nG Page 108
20. symbols are the fast the engine will work a Page 44 Symbols General Options A Tools Code Programming ON Disable Reading All Disable Reading All Allow reading Programming Codes only Code Programming OFF Disable Reading All Pro CMD 0001010 Enable Reading All Enable Reading All Enable to read all symbols and Programming Codes Enable Reading All Pro CMD 0001020 Enable Reading All 1D Enable Reading All 1D Pro CMD 0001040 Disable Reading All 1D Disable Reading All 1D Pro CMD 0001030 nG Page 45 Symbols SK Tools Code Programming ON Enable Reading All 2D l Enable Reading All 2D Code Programming OKE ee i Disable Reading All 2D Disable Reading All 2D Pro CMD 0001050 oa Page 46 Symbols Tools Code Programming ON Load Factory Default l Code Programming OFF Load Code 128 Factory Default Pro CMD 0400000 Enable Disable Code 128 Disable Code 128 Pro CMD 0400010 Enable Code 128 Pro CMD 0400020 ce Page 47 Symbols R Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 128 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code 128 Message Length is defined by Min Message Length and Code Programming OFF Max Message Length Min Message Length default 1 Pro CMD 0400030 Max Message
21. to reset all parameters to factory default Applicable conditions Code Programming OFF User options programming wrong configuration leads to reading mal function Forget details of previous programming and start over Load All Factory Default Pro CMD 0001000 User Default All user options can be saved as User Default It will be restored in non volatile memory Read Save as User Default to save all the current user options to be User Default and erase the previous User Default Read Load User Default to restore the engine to User Default Save as User Default Pro CMD 0001150 Load User Default Pro CMD 0001160 Programming the Engine Query Product Information NA Tools Code Programming ON Product information could be obtained by reading Query Product Information barcode The engine will send it to the Host immediately Power ON Send Product Info the engine sends product information through serial port only to the Host after Power ON Code Programming OFF Query Product Information Pro CMD 0003000 Power ON Do not Send Product Info Pro CMD 0007000 Power ON Send Product Info Pro CMD 0007010 The product information is provided as follows Device Manufacture Date Device serial number S N Device serial number User defined device serial number Manufacture ID 1 types of communication interfaces TTL232 EM3000 or RS232 EM2027 baud rate parity che
22. virtual keyboard It works in Code Programming ON USB connection no driver needed supports simulating the Imager transmission to be a Plug and Play base There is no driver required Code Programming OFF Select USB HID KBW Pro CMD 1100020 KBW input a Page 30 USB Interface B HID KB SK Tools Code Programming ON USB Country Keyboard Types l Refer The keyboard arrangements and country codes vary in different countries country codes to the table USB Country Keyboard Types Follow the steps mentioned below to program Code Programming OFF 1 Code Programming ON 2 Select Country Code 3 Read digit codes according to country code 4 Save programming 5 Code Programming OFF Select Country Code Pro CMD 1103000 Emulate Norway keyboard 1 Code Programming ON ple 2 Select Country Code 3 Digit code I 5 4 Save Programming 5 Code Programming OFF nG Page 31 USB Interface fis o fo petti CA Pin O ww a 8 mm v sesto ES ame s tnm 8 nG Page 32 USB Interface Tools HID KBW deems an unknown character to be a character is not included in a country keyboard type It may not be able to allocate and send a keystroke thus lead to an error beep Code Programming ON Unknown Characters Beep II l gramming OFF Code Pro No Beep Unkown Character Pro CMD 1103030 Beep Unkown Character Pro CMD 11030
23. 0 2000 change One Reading Timeout to 2 seconds 0405140 Disable Fixed Length of Interleaved 2 of 5 0000160 Save The batch setting code PDF417 is as follow EO a Page 135 Batch Programming Use batch setting code X Tools Code Programming ON Read Code Programming ON then read enable batch setting code and then read the batch setting code produced just now finally Read Code Programming Off Code Programming OFF Code Programming ON Pro CMD 0006010 y Allow Read Batch Code Pro CMD 0001110 y ui Batch Setting Code y Code Programming OFF Pro CMD 0006000 Y Page 136 Appendix Digit Code It is must to be read save after read digit code 0 Pro CMD 0000000 4 1 Pro CMD 0000010 Pro CMD 0000040 5 Pro CMD 0000050 Pro CMD 0000060 Pro CMD 0000070 a Page 137 Appendix Digit Code 8 Pro CMD 0000080 9 Pro CMD 0000090 A Pro CMD 0000100 B Pro CMD 0000110 oa Page 138 C Pro CMD 0000120 D Pro CMD 0000130 E Pro CMD 0000140 F Pro CMD 0000150 Appendix R Tools Code Programming ON In order to save the received data Save has to be read after data transition completed If error occurs when reading data the wrong data can be deleted and the setting up can be done again Eg after a program code is received then 123 in order is received
24. 31 Suppose select country keyboard types France number 7 read a barcode ADF Since the D 0xDO is not included in France country code the Imager skip D e and transmit AF For factory default no beep produced Read Beep Unkown p Character to indicate unknown character dea Page 33 USB Interface Tools 7777777777777 Code Programming ON Emulate ALT keypad When enabled full ASCII characters 0x00 Oxff can be sent over the numeric key pad regardless country keyboard selections l ALT Make Code Programming OFF 2 According to the ASCII value input the numbers over the numeric keypad 3 ALT Break No Emulate ALT keypad Pro CMD 1103060 Emulate ALT keypad Pro CMD 1103061 Suppose country code 7 France is selected and Emulate ALT keypad is enabled Barcode message ADF 65 208 70 will be sent as l ALT make 0 6 5 ALT Break p E 3 ALT make 2 0 8 ALT Break 3 ALT make 0 7 O ALT Break nG Page 34 USB Interface SB HID KBW Tools Code Programming ON Function Key Mapping When enabled function characters 0x00 0x1F are sent as ASCII sequences Over the numeric keypad 1 Ctrl make Code Programming OFF 2 Hit function key 3 Ctrl Break No Function Key Mapping Pro CMD 1103130 Function Key Mapping Pro CMD 1103140 USB HID KBW set to be factory def
25. 8030 Max Message Length default 48 Pro CMD 0408040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF E To set Min Message Length of Code 39 to 8 bytes and Max Message Length to 12 bytes ple a Page 70 Symbols Tools Code Programming ON Check Digit Code 39 may include Check Digit not compulsory following its barcode l message It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digit o Code Programming OFF Check Do Not Transmit Check Digit means to read and check If verification is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is suc cessful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All
26. Addenda Code Code Programming OFF 1234 567 E ES EZ Disable 2 Digits Addenda Code Pro CMD 0401050 Enable 2 Digits Addenda Code Pro CMD 0401060 5 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 5 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 5 digits Addenda Code rom qo 89012 i i l l d 1234 567 k l Disable 5 Digits Addenda Code Pro CMD 0401070 Enable5 Digits Addenda Code Pro CMD 0401080 Enable 2 Digits Addenda Code read an ordinary code and 2 digits Addenda Code Enable 5 Digits Addenda Code read an ordinary code and 5 digits Addenda Code Disable 2 Digits Addenda Code read an ordinary code only and ignore 2 digits Addenda Code Symbols XX Tools Code Pro gramming ON EAN 8 expand to EAN 13 Expand EAN 8 to EAN 13 by adding 5 bytes of 0 to the left and then transmit Code Programming OFF Do Not Expand to EAN 13 Pro CMD 0401090 Expand to EAN 13 Pro CMD 0401100 UD Page 51 Symbols R Tools eee Code Programming ON Load Factory Default I Load EAN 13 Factory Default Pro CMD 0402000 Code Programming OFF Disable EnableEAN 13 Enable EAN 13 Pro CMD 0402020 Disable EAN 13 Pro CMD 0402010 Check Digit Transmi
27. Characters Behind 33 EE E PO EP PE E RR RR 34 Funchal ea 33 ASCII Function Key Mapping Table 36 ie O 37 CIPS RR AAA 37 Convert E 38 Emulate Numeric KEYPAD varices 39 WE DLE RR A 40 USB COM Port EmMm lati f lei ae 41 NID POS a NONA NAGANA ae 42 LEO AA KAPA 42 Access the Device in Your POSTA 43 Getting Scanned BA 43 A e e E O CO rn A 43 Symbols APO aia lirio 44 rs eR o A O DO O beeen 45 Dis bl R ading a 45 Enable Reading E 45 Enable cad na EU AR AA 45 Disable leading Dear 45 Enable Reading All EE 46 Disable Radins e RE 46 uia ee P H 47 Load AG MINE 47 Enable Disable E E 47 Select Message RR AA 48 e a 49 bodies ail 49 Enable Disable UDU BAN lia 49 CREDE O loi aos 49 Table of Contents 2 Digits Addenda KA 50 5 Digits Addenda Code AA 50 Ianus expand tou inti eu TTTTTTTTTTTTTTTETTTTTTTTTTRTTTTTTTTTTE ETT ME 34 NA jo PO TTT 32 Load Factory Paa AA AA TU DU CD 52 Disable Enable EA EK E 52 Check Bia pares ga A 52 2 Digits Addenda AA AT 53 DEA 33 UPC CO COPE CE E ECO Em O OP O PC PU TE ET 54 aaa Dama AA E ea i aa Aa 54 Disable Enable UPOD Tr 54 Check RR RR a E eE e S E 54 SEET 55 5 a ga AA 55 MMAR A Delt 0 aipim a 56 UPC E Expand OPO cun 56 Ubi a7 Load Factory REI dd a a o cd rde uM UU PERbA cU ME aM CoU EAT UN RE 57 Disable BRADIPO T AA 57 atc gp
28. Code Programming OFF Single Data Matrix Only Read either Data Matrix Twin Data Matrix Only Read both Data Matrix The transmission sequence is left upper Data Matrix followed by right lower Data Matrix Both Single amp Twin Read both Data Matrix If successful transmit as twin Data Matrix Otherwise try single Data Matrix only Single Data Matrix Only Pro CMD 0504070 Twin Data Matrix Only Pro CMD 0504080 Both Single amp Twin Pro CMD 0504090 a Page 110 Symbols R Tools Code Programming ON Da II Data Matrix has two formats Square symbols which has the same amount of models in length and gramming OFF Code Pro width 10 10 12 12 144 144 Rectangular symbols which has different amounts of models in length and width 6 16 6 14 14 22 Enable Rectangular Symbols Pro CMD 0504110 Disable Rectangular Symbols Pro CMD 0504100 Forward Backwrd Direction Data Matrix Data Matrix has forward or backwrd direction Forward Direction Barcode Light colour ground Deep colour bars Backwrd Direction Barcode Deep colour ground Light colour bars Forward Direction Barcode Only Pro CMD 0504320 Both Pro CMD 0504322 Backwrd Direction Barcode Pro CMD 0504321 a Page 111 Symbols Tools Code Programming ON Load Factory Default l Code Programming OFF Load Maxicode Factory Default Pro CMD 0505000 Enable Disable Maxicode
29. F417 3 Read Digit Code 7 0 4 Read Save Programming 5 Read Code Programming OFF Load Code ID factory default including PDF417 1 Read Code Programming ON 2 Read 2D Load Code ID Factory Default 3 Read Code Programming OFF Modify PDF417 Pro CMD 0005000 Modify Data Matrix Pro CMD 0005030 Modify QR Code Pro CMD 0005010 Modify Maxicode Pro CMD 0005040 Modify Aztec Pro CMD 0005020 User Define Code Pro CMD 0005090 oa Page 123 Prefix Suffix SX Tools Code Programming ON Code Programming OFF Modify EAN 8 Pro CMD 0004040 Modify EAN 13 Pro CMD 0004050 Modify ITF 6 Pro CMD 0004100 Modify UPC E Pro CMD 0004060 Modify Code 39 Pro CMD 0004130 Modify UPC A Pro CMD 0004070 Modify Codabar Pro CMD 0004150 Modify Interleaved 2 of 5 Pro CMD 0004080 Modify Code 93 Pro CMD 0004170 Modify ITF 14 Pro CMD 0004090 a Page 124 Prefix Suffix SX Tools Code Programming ON Modify Code 128 Pro CMD 0004020 Code Programming OFF Pro CMD 0004240 Modify UCC EAN 128 Pro CMD 0004030 Modify Industrial 25 Pro CMD 0004250 Modify Code 11 Pro CMD 0004280 Modify Standard 25 Pro CMD 0004260 Modify EAN UCC Composite Pro CMD 0004300 Modify Plessey Pro CMD 0004270 Modify GSI Databar Pro CMD 0004310 Modify MSI Plessey Pro CMD 0004290 oa Page 125 Prefi
30. Factory Default Code Programming OFF Pro CMD 0416000 i Fnable Disable ISBN Enable ISBN Pro CMD 0416020 Disable ISBN Pro CMD 0416010 Transmit Transmit 13 digits Pro CMD 0416030 Transmit 10 digits Pro CMD 0416040 a Page 85 Symbols SK Tools eee Code Programming ON B Wi Code Programming OFF Load Industrial 25 Factory Default II Pro CMD 0417000 Fnable Disable Industrial 25 Enable Industrial 25 Pro CMD 0417020 Disable Industrial 25 Pro CMD 0417010 a Page 86 Symbols SK Tools Code Programming ON Select Message Length It is used to program the valid reading length of Industrial 25 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Industrial 25 Message Length is defined by Min Message Length and gramming OFF Max Message Length II Min Message Length default 6 Pro CMD 0417030 Max Message Length default 48 Pro CMD 0417040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code
31. IDT CH Value through Innovation 2DScan FX100 Barcode Scanner Scanner User s Manual 80108506 001 rev B Table of Contents Content About this guide Idtech A to ID Support A EE 2 Getting to Start NO NAA 3 LIE Lite 4 o dii AAA A TQ 4 EHS 4 BEL RR TORA 5 Communication nilo in 6 Connecting with USB Cable nani e 7 Connecting with RS232 EE 8 Eee Re EEE 9 SPEC AA 10 Pana nor NOO T Mik eT Tr 2f Programming the Engine PP e o AA 12 CUR lara 12 Command Oil 12 COuick e nni 12 Programming NA PR RE 13 Code Programming AA AA MAA AR 14 Mee E e ETE TT E Oo A E oT RE 15 ORRORE RR DNE UENIRE O ENSEM NN NICE DN INA TE 16 E MERE ID d dE NE I EE Det 17 IPod aria is 0 NN TNNT MERO TT 17 Decoding eio M RIO I 17 Decoding Beep VOLUME AA 18 COMERC DEE aaa AA AA TL 18 Beep Denotation Beeper Defmtons EO LL VL re Ful un d a dE anu 18 Reading ARR PAR A 19 Reading Timeout and Delay sr iaia 20 SP ORI AA AA NON A 21 Exposure Imaging MOGS soria cri 22 A A e O A 23 Factoty RA AA 23 Libellula 23 Query Product Information oa freada RR IRR A RA E I 24 a Page I Table of Contents RS232 Interface TREO CCO PR RR RR IE 23 A Eo AAP 26 BANI nan a a oa oo E o o aa 26 Parity adi aa 27 Hardware Auto Flow Cola calare ia 27 Data Bits Transmitted AA AA AA 28 IE RR VR RO e E ET 28 USB Interface lode 29 CE SUL qu siii aaa 30 USB Country Keyboard Ty Pescia siano ene cut ira beu NAGANA edi tt Lena errare 31 Unknown
32. IM ID List Symbol AIM ID Possible AIM ID Modifiers m Code 128 UCC EAN 128 EAN 8 EAN 13 EAN 13 with Addon UPC E UPC E with Addon UPC A UPC A with Addon Interleaved 2 of 5 ITF 6 ITF 14 Matrix 2 of 5 Code 39 Codabar Code 93 Code 11 ISBN Industrial 25 Standard 25 Plessey MSI Plessey GS1 Databar EAN UCC Composite PDF417 QR Code Aztec o 1 W Chinese Sensible Code Km Reference ISO IEC 15424 2008 Information technology Automatic identification and data capture techniques Data Carrier Identi fiers including Symbology Identifiers a Page 145 Appendix 3 Chinese Sensible Code oag Page 146 Appendix Symbols ID Number Symbol ID Number a Page 147 Appendix ASCII Table w NUE Nullchar ENQ Enqui 06 ACK Acknowledgment BEL Bell a BS Backspace O O AT Horizontal Tab Oa Line Feed P W VT VeialTa O Od ER Carriage Return SP Space a Page 148 Minus Dash Dot Forward Slash Less Than Equal Sign Greater Than Question Mark AT Symbol ed ei BoD E Ba a Be A E HA Har MO F E ill pr ln TE UY en Appendix ASCII Table Page 149 Equal Sign AT Symbol Bef Greater Than Bai Question Mark 0 qu G Dot un o A E E EN n Sj N WI SOID CO DN Jm noe eo en en n en eo en E Forward Slash eu gg Genie Bc ess
33. Length default 48 Pro CMD 0400040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two wA lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length To set Min Message Length of Code 128 to 8 bytes and Max Message Length to 12 bytes read these programming codes sample 1 Code Programming ON NI Select Min Message Length 3 Digit Code 8 see Digit Code 4 Save Programming see Digit Code 5 Select Max Message Length 6 Digit Code 1 7 Digit Code 2 8 Save Programming 9 Code Programming OFF a Page 48 Symbols Tools eee Code Programming ON Load Factory Default I Code Programming OFF Load UCC EAN 8 Factory Default Enable Disable UCC EAN 8 Enable UCC EAN 8 Pro CMD 0401020 Disable UCC EAN 8 Pro CMD 0401010 Check Digit UCC EAN 8 is fixed 8 digits barcode and the last digit is check digit Transmit Check Pro CMD 0401040 Do Not Transmit Check Pro CMD 0401030 nG Page 49 Symbols BEANS Jo XX Tools o Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 2 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 2 digits
34. Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two VA lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length To set Min Message Length of Matrix 2 of 5 as 8 bytes and Max Message length as 12 bytes read these programming codes 1 Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Appendix Pxxx Save Programming see Digit Code Appendix Pxxx Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF SPD de ALIO Symbols Tools Code Programming ON Check Digit Matrix 2 of 5 may include Check Digit not compulsory following its barcode l messages It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check digit Check Do Not Transmit Check Digit means to read and check If Code Programming OFF verification 1s successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode mes sage to the Host The number of Matrix 2 of 5 barcode bits check digit contained
35. O RI E dil Forward Backwrd Direction Data Matrix iii a 111 LEG TTT TTT m Mhanhbabnoi 112 Load Factory AAA e RO AA 112 Enable Disable Mixic0de crr iii 112 Select E D cla 113 Chinese Sensible Ci rai daga aghi 114 Load Factory Delli 114 Enable Disable Chinese Sensible Ole SE LA 114 Select Message E BE 115 OCR TOJU CHON PR RR ON SP OOOO EEE III 116 Prefix Suffix IAA IU TOT FRABOSA RE 117 General Poni 118 Disable or Enable Pref Sienna 118 e E ORE AE 119 Disable or Enable User Pre ii tutor d erede eesg re ben t ieteiurbRrsat Uese pd Ub Edad Es 120 Program User Prefix ea 120 AN RAI 12 Irina 122 Cooper 122 Modify Code ID E 123 o A e ER OO E O o A 126 Disable or Enable Esselte 126 Program User SURX eege 126 lle 127 Disable or Enable ermanno raevan 127 Program la E E E EE GNG 127 a Page V Table of Contents Message Interception amp Pack ege CUCIRE OO O E E AE 128 Message Aa 129 Programming 1D Intercept Option tege eege 130 Programming 2D Intetcept OPIO APA GASA 131 lu CERA ARR ITA 132 AKOO NONA AA AA dana 132 LELE AA 132 Batch Programming AA NONA ANA NAA OTTO AA IA 133 How to build a batch command AA nata 134 Produce setina Cat 135 Use batch setting CONG maa alii 136 Appendix Digit Code meen E Pe O ERR H A 137 i sx DOES AA 139 Factory Default ia a a 140 FIL EDE TETTE E om E E e E RR 145 IE EI A 146 Symbols ID NUDE AGA E AA AA AA 147 a Page VI About this gui
36. Plessey The engine will not send barcode message to the Host if the decoded data length does not match the valid length Plessey Message Length is defined by Min Message Length and Max Code Programming OFF Message Length Wi Min Message Length default 4 Pro CMD 0419030 Max Message Length default 48 Pro CMD 0419040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of Plessey to 8 bytes and Max Message Length to 12 bytes E le a Page 93 Symbols Plessey K Tools Code Programming ON Check Digit Plessey may include Check Digits not compulsory following its barcode message l The two digits verify the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digits o Code Programming OFF Check Do Not Transmit Check Digit means to read an
37. Pro CMD 0408050 Check Transmit All Pro CMD 0408070 Check Do not transmit Check Digit Pro CMD 0408060 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error SVO E g Reading a 4 byte include check byte Code 39 with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error Decode ASCII Code 39 can include full ASCII characters For factory default the engine only decodes part of them Read Full ASCII decode to decode full ASCII characters Partial ASCII Decode Pro CMD 0408100 Full ASCII Decode Pro CMD 0408110 nG Page 71 Symbols R Tools Code Programming ON Load Factory Default l Code Programming OFF Load Codabar Factory Default Pro CMD 0409000 Enable Disable Codabar Enable Codabar Pro CMD 0409020 Disable Codabar Pro CMD 0409010 ce Page 72 Symbols Tools Code Programming ON Select Message Length It is used to program the valid reading length of Codabar The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code Programming OFF Codabar Message Length is defined by Min Message Length and Max Message Length Min Message Length default 2 Pro CMD 0409030 Max Message Length default 60 Pro CMD 0409040 1D bar code M
38. QR Code Pro CMD 0502020 Disable QR Code Pro CMD 0502010 na Page 101 Symbols QR Code NA Tools Code Programming ON Select Message Length It is used to program the valid reading length of QR Code The engine will not send l barcode message to the Host 1f the decoded data length does not match the valid length QR Code Message Length 1s defined by Min Message Length and Max Code Programming OFF n Mim Message Length default 1 Pro CMD 0502030 Max Message Length default 7089 Pro CMD 0502040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length QR Code Please program Max amp Min Message Length to the same value To set Mm Message Length of QR Code to 8 bytes and Max Message Length to 12 bytes read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF ple pepe c is n de UA a Page 102 Symbols XX Tools Code Programming ON QR Twin Code QR twin code is 2 QR barcodes paralleled vertically or horizontally They must have the same direction Their specifications must be similar and the distance between them must be short There are 3 options for reading QR
39. Read Code Programming ON 2 Read Enable Interception 3 Read Program Intercept Option 4 Check Symbols ID Number table for QR Code 2 Read below digit barcodes Barcode Type Data Interception 1 Data Interception 2 Rules 1 Maximum intercept 3 barcode message sections 2 Maximum value is 9999 for start digital and end digital 3 Overlaps of barcode message sections are allowed and work independently 4 Start unit and end unit determine its message section In the above example ascending 000001 and 000020 means the first 20 digits 5 To intercept only one digit program start unit and end unit to be the same value nG Page 131 Message Interception amp Pack R Tools NN Code Programming ON Introduction Data Pack is for the special requirements of barcode message There are 3 types of data pack Data pack effects all data formats in that be sure to load the default Disable Pack if pack is not required Code Programming OFF Disable Pack Pro CMD 0314000 Normal Pack Normal pack format STX ATTR LEN AL TYPE DATA LRC STX 0x02 ATTR 0x00 LEN Barcode message length is expressed by 2 bytes range 0x0000 0xFFFF which is between 0 and 65535 AL TYPE 0x36 DATA Barcode message LRC Parity byte The algorithm 1 computation sequence is LRC 0xFF STX ATTR LEN AL TYPE DATA 2 computation method is XOR byte by byte Normal Pac
40. Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of Industrial 25 to 8 bytes and Max Message Length to 12 E le a Page 87 Symbols Industrial 25 Tools Check Digit Industrial 25 may include Check Digit not compulsory following its barcode message It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digit Check Do Not Transmit Check Digit means to read and check If verifica tion is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0417050 Check Transmit All Pro CMD 0417070 Check Do Not Transmit Check Digit Pro CMD 04170601 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length 1t will lead to an error E g Reading a 4 byte include check byte Industrial 25 with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error ce Page 88 Symbols SK Tools Code Programming ON
41. Symbols Data Matrix NA Tools Code Programming ON Select Message Length It is used to program the valid reading length of Data Matrix The engine will not l send barcode message to the Host if the decoded data length does not match the valid reading length Data Matrix Message Length 1s defined by Min Message Length and Max Message Length Code Programming OFF Min Message Length default 1 Pro CMD 0504030 Max Message Length default 3116 Pro CMD 0504040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length Data Matrix Please program Max amp Min Message Length to the same value To set Min Message Length of Data Matrix to 8 bytes and Max Message Length to 12 bytes read these programming codes 1 Code Programming ON 2 Select Min Message Length 3 Digit Code 8 see Digit Code 4 Save Programming see Digit Code 5 Select Max Message Length 6 Digit Code 1 7 Digit Code 2 8 Save Programming 9 Code Programming OFF nG Page 109 Symbols Data Matrix NA Tools Code Programming ON Data Matrix Twin Code Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally They must have the same direction Their specifications must be similar and the distance between them must be short There are 3 options for reading Data Matrix
42. Than AA eee Y JU De 4 6____ en en LA A aaa sr t laj w SO S JIMmMI TI VI DIIDVIO wells Kaell eg NO ME Md LU DU DU DL AL AL Da IL CO CO LO co TF D NO Pm 00 N af Dl SIDI DI HI SD JJ mImT xiu un NN Appendix ASCII Table tigt lt gyt T I0 N N N Page 150 ID TECH 10721 Walker Street Cypress CA 90630 714 761 6368 www idtechproducts com 80108506 001 rev B
43. age Length is equal to Min Message Length the engine will only sup port barcodes of the length read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of Code 93 to 8 bytes and Max Message Length to 12 bytes E le 96 9 tM a Page 77 Symbols R Tools Check Digit Code 93 may include Check Digits not compulsory following its barcode message The two digits verify the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digits Check Do Not Transmit Check Digit means to read and check If verification is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is suc cessful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0410050 Check Transmit All Pro CMD 0410070 Check Do not transmit Check Digit Pro CMD 0410060 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error SV E g Read
44. am Terminal Read Program Terminal Then program terminal byte s To end the suffix read Save programming The terminal byte is programmed in its hex values See example below Note The maximum length for terminal is 2 bytes Program Terminal Pro CMD 0310000 Program Ox0D as Terminal Pro CMD 0310010 Program Ox0D 0x0A as Terminal Pro CMD 0310020 a Page 127 Message Interception amp Pack Introduction Barcode message could divide information into different sections such as product ID manufacture ID and so on They are important overall However at certain situations some of them are not of interest This is where message interception comes in Message interception feature allows transmission of selected section s Message intercept only applies to raw barcode messages The sequence of a read to transmit without message intercept is Read a raw barcode gt Add prefix gt Append suffix gt Append terminal gt Transmit to Host The sequence of a read to transmit with message intercept is Read a raw barcode gt Intercept Message Add prefix Append suffix gt Append terminal gt transmit to Host A special programming pack can insert barcode messages into a certain message format Then the processing sequence is Read to obtain barcode message gt Intercept gt Add prefix gt Append suffix Pack gt Append terminal gt Transmit
45. ault Enable Emulate CTRL keypad Read barcode A tab F 0x65 0x09 0x70 The sequence is I Keystroke A p e 2 Input Ctrl I by Ctrl make Keystroke I Ctrl break 3 Keystroke F For some text editors Ctrl I is italic convert So the output may be AF keypad nG Page 35 USB Interface USB HID KBW ASCII Function Key Mapping Table ASCII HEX Function ke ASCII HEX Function Key y O mm m N Nn E O oO A o Hibla Fr Oo O O ley a Page 36 USB Interface Q Tools Code Programming ON Keystroke Delay This parameter sets the delay in milliseconds between emulated keystrokes Scan programming code below to increase the delay when the Host require a slower trans mission of data Code Programming OFF No Delay Pro CMD 1103050 Long Delay 40ms Pro CMD 1103052 Short Delay 20ms Pro CMD 1103051 Caps Lock The case of the data is inverted regardless of the state of the Caps Lock key on the Host Lower case and upper case are converted correspondingly Disable Caps Lock Pro CMD 1103010 Enable Caps Lock Pro CMD 1103020 Convert Case Emulate ALT keypad and Function Key Mapping option prevails Enable Caps Lock USB Interface Q Tools Code Programming ON Convert Case The Imager converts all barcode messages to the selected case Code Programming OFF No Cas
46. ble Code Enable Chinese Sensible Code Pro CMD 0508020 Disable Chinese Sensible Code Pro CMD 0508010 When the engine can not read Maxicode please read Enable Chinese Sensible Code and try again me Page 114 Symbols z T Chinese Sensible Code d Tools Code Programming ON Select Message Length It is used to program the valid reading length of Chinese Sensible Code The engine will not send barcode message to the Host if the decoded data length does not match the valid reading length Maxicode Message Length is defined by Min Message Length and Max Code Programming OFF Message Length li Min Message Length default 1 Pro CMD 0508030 Max Message Length default 7827 Pro CMD 0508040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length Maxicode Please program Max amp Min Message Length to the same value To set Min Message Length of Chinese Sensible Code to 8 bytes and Max Message Length to 12 bytes read these programming codes 1 Code Programming ON 2 Select Min Message Length 3 Digit Code 8 see Digit Code 4 Save Programming see Digit Code 5 Select Max Message Length 6 Digit Code 1 7 Digit Code 2 8 Save Programming 9 Code Programming OFF a Page 115 OCR Introduction OCR Optical Character Recognition
47. ck data bits stop bit 1D Indicate that reading 1D is allowed Symbols are divided by comma Additional features format l connect features 2 Min Message Length gt Max Message Length 3 No Check Digit or Check Digit 4 Fixed Length 2 64 even value It is in this format Fixed Length 2 4 6 8 10 12 2D Indicate that reading 2D is allowed Symbols are divided by comma EE Additional feature format Min Messa th Scan Mode Scan Mode 1 Manual Scan 2 Auto Scan 3 Continuous Scan RS232 Interface Introduction When the engine is connected to the Host with RS232 cable system will select RS232 connection by default Under RS232 connection the engine and the Host use the same communication parameters baud rate parity check data bits select and stop bits select Select RS232 Connection Pro CMD 1100000 nG Page 25 RS232 Interface Serial Port SN Tools Code Programming ON The engine and the Host should use the same serial port parameters baud rate parity check data bits and stop bits The sequence is as follows 9600 baud rate null parity check 8 data bits 1 stop bits Baud Rate baud rate to match the baud rate setting of the Host device Otherwise they can not i e Code Programming OFF Baud rate is the number of bits of data transmitted per second Set your scan engine The engine supports the following baud rates The default baud rate is 9600 Pro
48. d 25 may include Check Digit not compulsory following its barcode message It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digit Check Do Not Transmit Check Digit means to read and check If verifica tion is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0418050 Check Transmit All Pro CMD 0418070 Check Do Not Transmit Check Digit Pro CMD 0418060 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error WT E g Reading a 4 byte include check byte Industrial 25 with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error ve Page 91 Symbols Tools Code Programming ON II Code Programming OFF Load Plessey Factory Default Pro CMD 0419000 Enable Disable Plessey Enable Plessey Pro CMD 0419020 Disable Plessey Pro CMD 0419010 a Page 92 Symbols XX Tools Code Programming ON Select Message Length IIU l It 1s used to program the valid reading length of
49. d check If verifica tion is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0419050 Check Transmit All Pro CMD 0419070 Check Do Not Transmit Check Digit Pro CMD 0419060 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error E g Reading a 4 byte include check byte Plessey with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error ve Page 94 Symbols SX Tools Code Programming ON Code Programming OFF Load MSI Plessey Factory Default Pro CMD 0420000 Enable Disable MSI Plessey Enable MSI Plessey Pro CMD 0420020 Disable MSI Plessey Pro CMD 0420010 a Page 95 Symbols SK Tools CO Code Programming ON It is used to program the valid reading length of MSI Plessey The engine will not send barcode message to the Host if the decoded data length does not match the valid length m Code Pro ing OFF MSI Plessey Message Length is defined by Min Message Length and Max Message Length Min Message Length default 4 Pro CMD 0420030 Max Message Length
50. de Introduction This FX100 Embedded 1D 2D Barcode Scanner Integration Guide provides general instructions for OEM integration Graphic Notations Tool Handy item for a task Attention Important subject to be aware of or to avoid Tips Helpful information about a topic or a feature E Example Illustration of how to use a feature inple oag Page 2 Getting to Start Introduction FX100 is an omnidirectional imager capture decode and transfer ID amp 2Dbarcode This chapter presents an overall picture of how to use FX100 step by step Please have an FX100 handy This chapter is recommended to general users maintenance personnel and software programmers a Page 3 Getting to Start Unpacking Unpacking Unpack FX100 and accessories Check with the packing list Make sure that there is no damage or missing part s If any damage or missing parts please keep the original package and contact your supplier for services Outline of FX100 The figure below shows major components of FX100 Indicator Sensor Light FX100 Outline The scan window must be kept clean Improper maintenance will breach the limited warranty Avoid rough objects not to damage or scratch the window Use brush to remove the stain Use soft cloth cloth for glasses to clean Prohibit spraying towards the window Only use clean water as a cleanser a Page 4 Getting to Start Data Int
51. de 3 short low 2 high reading failure 1 long low Unknown Character Virtual Keypad USB connection a Page 18 Programming the Engine Reading Mode NA Tools matically initiates reading After completion of reading the engine goes to idle Code Programming ON Auto Mode The ambient luminance change in front of the engine auto Both luminance change and the Trigger can initiate reading when idle Continuous Mode Pull the Trigger line low to start reading The engine will keep reading To stop pull trigger line low again Code Programming OFF Auto Mode Pro CMD 0302010 Continuous Mode Pro CMD 0302020 a Page 19 Programming the Engine Reading Timeout and Delay d Tools Code Programming ON One Reading Timeout If the engine doesn t read any barcode during the timeout period it will stop reading automatically One Reading Timeout is valid in Auto mode The default timeout is 3000ms Same Barcode Reading Delay It is used to avoid misreading on the same Code Programming OFF barcode the same format and message in a Same Barcode Reading Delay Time It is valid only 1n Auto mode The default delay 1s 1500ms One Reading Timeout Pro CMD 0313000 Same Barcode Reading Delay Pro CMD 0313010 There are two options available in Same Barcode Reading Delay Multi reading Prohibit The same symbol can be read after delay Multi reading Semi prohibit The same symbol can
52. disable Disable Specified Length Pro CMD 0405140 Add Code Length Pro CMD 0405160 Enable Specified Length Pro CMD 0405150 Remove Code Length Pro CMD 0405170 The engine only read Interleaved 2 of 5 which are 12 and 24 bytes Code Programming ON Enable Specified Length Add Code Length Digit Code Q I 2 Save Programming Add code length Digit Code 0 2 4 Save Programming Code Programming OFF 96 LO AN The engine only read Interleaved 2 of 5 between 12 bytes and 24 bytes 1 Code Programming ON 2 Enable Specified Length 3 Add Code Length 4 Digit Code O 1 2 5 Digit Code 0 2 4 6 Save Programming 7 Code Programming OFF Symbols XX Tools o Code Programming ON ITF 14 is a fixed length 14 bytes Interleaved 2 of 5 barcode with Check digit By factory default 1t 1s disabled l When enabled ITF 14 precedes 14 byte Interleaved 2 of 5 barcode Code Programming OFF Disable ITF 14 Pro CMD 0405080 Enable ITF 14 Do Not Transmit Check Digit Pro CMD 0405090 Enable ITF 14 Transmit Check Digit Pro CMD 0405100 For instance when ITF 14 is enabled and Interleaved 2 of 5 is disabled the ITF 14 and 14 bytes Interleaved 2 of 5 with check digit can be read but other Interleaved 2 of 5 can not a Page 64 Sy
53. e Conversion Pro CMD 1103040 Convert All to Upper Case Pro CMD 1103041 Convert All to Lower Case Pro CMD 1103042 Read Convert All to Lower Case Barcode message AbC issentas abc a Page 38 USB Interface Q Tools Nm EEE ene ven II l Code Programming OFF When disable the whole barcode message will be emulated as keystrokes on main keyboard Read Emulate Numeric Keypad to enable the function when 0 9 is of the barcode message it will be emulated as keystrokes on numeric keypad But sign auch as 7 m 2 emulated as keystrokes on main keyboard 1S Numeric keypad is normally at the right of a standard keyboard This function is effected by the current state of Num Lock of Host s numeric keypad The emulate numeric keypad couldn t control the state of Num Lock So if Num Lock light off the output is function key instead of numbers Disable Emulate Numeric Keypad Pro CMD 1103110 Emulate Numeric Keypad Pro CMD 1103120 Check Num Lock light before use this function Enable Emulate ALT keypad will automatically disable this function Enable Emulate Number Keyboard and read the A4 5 barcode If Num Lock on the Host is ON the data received will be A4 5 If Num Lock is OFF Host will receive the data from keyboard as follow Host receives data A This character is not includ
54. e Hardware Auto Flow Control Pro CMD 0104000 Enable Hardware Auto Flow Control Pro CMD 0104010 Before enabling this function please be sure that RTS CTS signal line is contained in RS232 cable If not a RS232 communication error will occur RS232 Interface XK Tools Code Programming ON Data Bits Transmitted l Select data bits transmitted to be 5 6 7 and 8 Ensure the selections on the engine and the Host are the same Code Programming OFF 8 Data Bits Pro CMD 0103030 l 6 Data Bits Pro CMD 0103010 7 Data Bits Pro CMD 0103020 i 5 Data Bits Pro CMD 0103000 Stop Bits Stop bit follows every byte to indicate the end of transmission and the start of the next transmission Default 1 stop bit 1 Stop Bits Pro CMD 0102000 2 Stop Bits Pro CMD 0102010 a Page 28 USB Interface Introduction When using a USB connection the default protocol is USB COM Port Emulation When only data transmission is needed through USB connection USB HID KBW option can be programmed It emulates the unit s transmission as a USB keyboard input The Host receives keystrokes of the virtual keyboard It is Plug and Play There is no driver required If a USB connection and an RS232 connection are used at the same time the engine will select USB connection by default for its priority a Page 29 USB Interface Q Tools USB keyboard input The Host receives keystrokes of the
55. e UPC E Enable UPC E Pro CMD 0403020 Disable UPC E Pro CMD 0403010 Check Digit UPC E is fixed 8 digits barcode and the last digit is check digit Transmit Check Pro CMD 0403040 Do Not Transmit Check Pro CMD 0403030 nG Page 54 Symbols ram XX Tools o Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 2 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 2 digits Addenda Code PES Code Programming OFF 78 I i Au Abort 2 Digits Addenda Pro CMD 0403050 Enable 2 Digits Addenda Code Pro CMD 0403060 5 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 5 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 5 digits Addenda Code ING 78901 p Disable 5 Digits Addenda Code Pro CMD 0403070 W Enable 5 Digits Addenda Code Pro CMD 0403080 Enable 2 Digits Addenda Code read an ordinary code and 2 digits Addenda Code Enable 5 Digits Addenda Code read an ordinary code and 5 digits Addenda Code Disable 2 Digits Addenda Code read an ordinary code only and ignore 2 digits Addenda Code Symbols XX Tools Code Programming ON Transmit
56. eading length of Interleaved 2 of 5 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code Programming OFF Interleaved 2 of 5 Message Length is defined by Min Message Length and Max Message Length Min Message Length default 6 Pro CMD 0405030 Max Message Length default 80 Pro CMD 0405040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two VA lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length To set Min Message Length of Interleaved 2 of 5 as 8 bytes and Max Message length as 12 bytes read these programming codes 1 Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Appendix Pxxx Save Programming see Digit Code Appendix Pxxx Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF E re dec Se do a Page 61 Symbols Interleaved 2 of 5 IS Tools Code Programming ON Check Digit Interleaved 2 of 5 may include Check Digit not compulsory following its l barcode messages It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check d
57. ed in keyboard thus the data will be sent as normal Next Host receives data 4 corresponding to the instruction of Cursor move to left Then Host receives data just back of cursor There is no input generated by data 4 as the data 5 corresponds to NO instruc tions ce corresponding to the instruction of delete the character USB Interface K Tools Code Programming ON A driver has to be installed before using this protocol to communicate with reader l The advantage of using this protocol is the fast data transmission Meanwhile the SDK can be easily integrated into the application system Code Programming OFF Select USB DataPipe Pro CMD 1100010 oa Page 40 USB Interface USB COM Port Emulation d Tools scanner the model of imitating USB to RS232 has to be chosen Hence the engine and the Host must communicate at the same parameters and the parameters of real serial port and visual serial port must be the same Code Programming ON When the USB port is connected to Host serial port in order to receive data from l Code Programming OFF Select USB COM Port Emulation Pro CMD 1100060 a Page 41 USB Interface R Tools mid 56 The HID POS interface is recommended for new applications It can send up to characters in a single USB report and is muchfaster than keyboard emulation HID based no custom driver required Much faster than keyboard emulat
58. erface PIN 10 PINI Cable Slot 1 ve ono 2 pe Na 9 3 2 3 ve de JPowrDCSV 0 0 4 wo O Serial Port Output RS232 Serial Port Input RS232 6 JNC 1 1 ST MM 4 4 4 4 7 NC aan 8 GND e Ground 9 po FUSS Data Signal ua Page 5 Getting to Start Communication Ports FX100 must connect to a Host to operate A Host can be PC POS or any intelligent terminal with at least one of the following communication ports USB RS232 or PS 2 1 USB USB port on Host 2s RS232 RS232 port on Host Please check the ports first to order the fitting cable nG Page 6 Getting to Start Connecting with USB Cable 1 Insert USB Cable RJ45 male head into FX100 cable slot 2 Insert USB Cable USB male head into Host s female USB connector a Page 7 Getting to Start Connecting with RS232 Cable 1 Insert RS232 cable RJ45 male head into FX100 cable slot 2 Insert RS232 cable RS232 male head into Host s female RS232 connector 3 Connect RS232 cable and the mains with power adapter a Page 8 Getting to Start 35mm Code39 10mil 170mm 55mm Code39 15mil 210mm 55mm PDF417 10mil 175mm 60mm PDF417 15mil 205mm 45mm Data Matrix 10mil 145mm 45mm Data Matrix 15mil j 175mm 45mm QR Code 10mil 140mm 50mm QR Code 15mil 175mm EAT NN MA er eT
59. essage Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two MD lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length ove Page 73 Symbols R Tools Check Digit Codabar may include Check Digit not compulsory following its barcode message It verifies the barcode message NO Check Transmit All means to read without check and transmit all bytes including barcode message and Check Digit Code Programming Check Do Not Transmit Check Digit means to read and check If verification is successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is suc cessful transmits all messages if not engine will not send barcode message to the Host NO Check Transmit All Pro CMD 0409050 eck Transmit All D CMD 0409070 Check Do not transmit Check Digit Pro CMD 0409060 When Check Do not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error SVO E g Reading a 4 byte include check byte Codabar with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error a Page 74 Symbols Tools Code Programming ON Transmit Start amp
60. ge Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF SARTRE nG Page 99 Symbols XX Tools Code Programming ON PDF417 Twin Code PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally They must have the same direction Their specifications must be similar and the distance between them must be short There are 3 options for reading PDF417 twin code Code Programming OFF Single PDF417 Only Read either PDF417 code IK Twin PDF417 Only Read both PDF417 codes The transmission sequence 1s left upper PDF417 code followed by right lower PDF417 code Both Single amp Twin Read both PDF417 codes If successful transmit as twin PDF417 only Otherwise try single PDF417 only Single PDF417 Only Pro CMD 0501070 Both Single amp Twin Pro CMD 0501090 Twin PDF417 Only Pro CMD 0501080 Forward Backwrd Direction PDF 417 PDF 417 has forward or backward direction Forward Direction Barcode Light colour ground Deep colour bars Backwrd Direction Barcode Deep colour ground Light colour bars Forward Direction Barcode Only Pro CMD 0501320 Both Pro CMD 0501322 Backwrd Direction Barcode Only Pro CMD 0501321 oa Page 100 Symbols XX Tools Code Programming ON Load Factory Default l Code Programming OFF Load QR Code Factory Default Pro CMD 0502000 Enable Disable QR Code Enable
61. gramming and QuickSet Programming Code Programming The Engine reads a set of specially encoded barcodes to program features In the following sections we will explain the options and features available and provide the barcodes to program them This method of programming the Engine is most straight forward However it requires manually readings of each barcode As all manual operations errors are more likely to occur Command Programming The Host can send the Pro CMD strings see the chapter of Software Interface to program the Engine In the following sections the Pro CMD strings will be included with the barcodes for Code Programming A fixture such as EVK3000 or other simplier circuit board could be used to program the Engines before they are installed into your equipments or systems Another alternative is to design the configuration capability in your equipments or systems This method of programming the Engine could be automated A software program can be developed to download all the configuration data to the Engine Note The programming results are restored in non volatile memory They will not be lost when the Engine is powered off a Page 12 Programming the Engine Programming Notation d Tools Code Programming ON lt 1 5 Code Programming OFF There are 4 parts of a notation 1 The first part of the notation is the barcode for Code Programming 4 gt ode Programming OFF Pro CMD 0006000 This is the
62. igit Check Do Not Transmit Check Digit means to read and check If Code Programming OFF verification 1s successful transmits barcode message if not engine will not send barcode message to the Host Check Transmit All means to read and check If verification is successful transmits all messages if not engine will not send barcode mes sage to the Host The number of Interleaved 2 of 5 barcode bits check digit contained must be even If it is odd a 0 will be added as the first digit The check digit generates automatically when a barcode is produced NO Check Transmit All Pro CMD 0405050 Check Do Not Transmit Check Digit Pro CMD 0405060 Check Transmit All Pro CMD 0405070 When Check Do Not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error E g Reading a 4 byte include check Digit Interleaved 2 of 5 with the Min Message Length being 4 bytes and Check Do Not Transmit Check digit enabled leads to an error a Page 62 Symbols Interleaved 2 of 5 IS Tools Code Programming ON Specified Lengths Program the engine to read specified lengths or ranges of specified lengths for Interleaved 2 of 5 The length value must be 3 decimal digits And the length value MUST be an even number between 2 to 64 Read Enable Specified Length to enable this feature or Disable Specified Length to
63. ing a 4 byte include check byte Code 93 with the Min Message Length being 4 bytes and Check Do not transmit Check Digit enabled leads to an error a Page 78 Symbols Tools eee Code Programming ON Load Factory Default I Load UCC EAN 128 Factory Default l Pro CMD 0412000 TN Enable Disable UCC EAN 128 Enable UCC EAN 128 Pro CMD 0412020 Disable UCC EAN 128 Pro CMD 0412010 a Page 79 Symbols Tools eee Code Programming ON Load Factory Default I Code Programming OFF Load GS1 Databar Factory Default Pro CMD 0413000 Enable Disable GS1 Databar Enable GS1 Databar Pro CMD 0413020 Disable GS1 Databar Pro CMD 0413010 Transmit AI 01 Character Transmit AI 01 Character Pro CMD 0413060 Do not Transmit AI 01 Character Pro CMD 0413050 oa Page 80 Symbols EAN UCC Composite NA Tools Code Programming ON Load Factory Default l Code Programming OFF Load EAN UCC Composite Factory Default Pro CMD 0414000 Enable Disable EAN UCC Composite Enable EAN UCC Composite Pro CMD 0414020 Disable EAN UCC Composite Pro CMD 0414010 Enable UPC EAN Composite Pro CMD 0414040 Disable UPC EAN Composite Pro CMD 0414030 When the engine can not read EAN UCC Composite please read Enable EAN UCC Composite and try again ona Page 81 Symbols R Tools Code Programming ON Load Factory Default l Code Program
64. ink LED keeps flashing when reading Code Programming OFF Illumination Keep ON LED keeps on when Power ON Illumination Read ON LED keeps on when reading Illumination OFF LED is off all the time Illumination Wink Pro CMD 0200000 Illumination Read ON Pro CMD 0200030 Illumination Keep ON Pro CMD 0200010 Illumination OFF Pro CMD 0200020 oa Page 15 Programming the Engine SX Tools Code Programming ON BM II Aim Wink LED keeps flashing when reading Aim Keep ON LED keeps on when Power ON Code Programming OFF Aim Wink Pro CMD 0201000 Aim Keep ON Pro CMD 0201010 oa Page 16 Programming the Engine XX Tools Code Programming ON Decoding Beep Read Beep ON to enable all decoding beep denotation and read Beep OFF to disable Code Programming OFF Beep ON Pro CMD 0203010 Beep OFF Pro CMD 0203000 Decoding Beep Type Type 1 Pro CMD 0203020 Type 3 Pro CMD 0203022 Type 2 Pro CMD 0203021 ce Page 17 Programming the Engine suy Tools A Code Programming ON Loud Tl il Low Pro CMD 0203032 Medium Pro CMD 0203031 Power On Beep Beep On Pro CMD 0204001 Beep OFF Pro CMD 0204000 Beep Denotation Beeper Definitions low higher higher higher Power ON completed successful reading of an ordinary barcode successful reading of an programming barco
65. ion and traditional RS 232 Note HID POS does not require a custom driver installation However a HID interface on Windows 98 does Select HID POS Pro CMD 1100080 ove Page 42 USB Interface Q Tools III Code Programming ON Access the Device in Your Program l CreateFile opens the device as a HID then ReadFile delivers the scanned data to the application Use WriteFile to send data to the device For complete information on USB and HID interfaces please see www USB Code Programming OFF i KKK Getting Scanned Data After scanning and decoding a bar code the device sends the following input report Report ID 0x02 Length of the bar code field Decoded Data CI pe p Jd fh p p p jo Decoded Data 1 56 58 61 Reserved 1 4 Symbology Identifier or N C 0x00 Decode Data VID and PID Table USB uses two numbers to identify a device and find the correct drivers The first is the VID Vendor ID assigned by the USB Implementers Forum The vendor ID VID is 1EAB hex The second is the PID Product ID A range of PIDs is used for each product sub family so each PID contains a base number and an interface type keyboard COM port etc a Page 43 Symbols Introduction This chapter lists all the available symbols and provides the programming barcodes to enable disable them Disabling reading of the symbols which do not apply will improve reading performance The few abling reading of the
66. is the technology that captures image of printed information and recognizes the image to editable characters The engine supports OCR B standard and specific typefaces such as 0123456 78 M l Nine numbers of OCR B typeface must be included 2 There must be a space between No 7 and No 8 number 3 It must start and end with IM There must be a space between IM and a number e Load SPEC OCR B Factory Default Pro CMD 0600000 Disable OCR Pro CMD 0600010 Fnable OCR Pro CMD 0600020 a Page 116 Prefix Suffix Introduction 1D barcodes could contain digits letters and symbols etc 2D barcodes could contain more data such as Chinese characters and other multi byte characters However in reality they do not and should not have all the information we need such as barcode type date and time of scan delimiter and so on in order to keep the code short and flexible Prefix and Suffix are how to fulfill the needs mentioned above They can be added removed and modified while the original barcode message is still in tact Barcode processing sequences Intercept barcode message Add Prefix Suffix Pack Terminate with Terminal and transmit a Page 117 Prefix Suffix SX Tools MITT Code Programming ON Disable or Enable Prefix Suffix Wi l Disable AlI Prefix Suffix Tran
67. k Pro CMD 0314010 a Page 132 Batch Programming RK Tools Code Programming ON Batch Programming can integrate a programming sequence into one barcode l Introduction Batch Programming Rules 1 Sub command is in this format Programming Command Parameters 2 Sub commands are terminated by semicolons Note that there is no blank between a sub command and its terminator semicolon 3 Save Programming 0000160 to terminate KI 4 Use Barcode Generator software to make the 2D batch barcode For example to generate a batch barcode for Illumination Keep ON 0200030 Auto Mode 0302010 One Reading Timeout 2000 0313000 and Disable Fixed Length Selection 0405140 for Inter leaved 2 of 5 0200030 0302010 0313000 2000 0405140 0000160 Generate a batch code Allow Read Batch Code Pro CMD 0001110 a Page 133 Batch Programming How to build a batch command Batch command can contain many commands Each command is divided by semicolon Batch command must be ended with save command Command structure command equal mark setting information The setting command list is provided below There are 4 setting command modes 1 Setting syntax 1 Command The most command is the one can be set at one time without the command EB The command setting the baud rate as 38400 bps 0100060 The command setting auto mode 0302010 2 Setting syntax 2 Command equal ma
68. laka A 8 57 2 Digits Addenda Code A iis 58 5 Dadda 58 Transmit Dellt iero 59 RZ la e EE 60 Load AN 60 Disable Enable Interleaved 2 of Da AA NAINA AG 60 Select Message FONO oo ao a ge q 61 CER RR AA 62 CEE IRR a RIA 63 AA AA 64 RR O 65 VETRI NR CN 66 Load Factory EEE TIT RUP 66 Disable Enable Mido 66 Select Message LENG aa AA AA AA AA 67 Co AA 68 CL RIE 69 Load Factory Dada ii cani 69 Enable Disable CONE 39 a nesana so ana rdo Ka Dt lanla Sad Os Saed ka KON 69 Transmit Start amp Stop Char ne ai a inde Pr ot iosuada ine M Rd ets 69 Select Message BA 70 Check pora a A 71 Pi 0 AA X 9 71 KEE 72 Load Factory AA 72 Enable Disable CONN iio aus ai 72 Select Mess ge TECIDO o sa 73 Ci cara ES 74 Transmit Start amp Stop EE 75 a Page III Table of Contents Olii 76 Load Factory DEU ama nA NAA loin olii 76 Enab Ba Slo Codo lieta 76 Select Nessas Cl CNO ENRIQUE a Check Mem O O RR REUNIR EDI 78 9 d ee 79 Load Factory DE Ulam AA GAAN 79 Enable Disable UCC EAN 128 lla 79 Ge Iulo RR RE O I 80 Ee sil TTT TTTTTTTTTTRRTTTTTTTTTTRTTETTTTTTTTTTTTTTTT 80 Enable Disable GS1 DIR 80 Transmit CON O i ONERE Tm 80 EAN UCC COMPOS ie T m9 81 Load Pico EE iena A 81 Enable Disable BAN UCC Compose ida 81 ll ii i i 82 Load An ta 82 Enable Disable Coletta oz Select Message RR A 83
69. mbols X Tools Code Programming ON ITF 6 is a fixed length 6 bytes Interleaved 2 of 5 barcode with check digit When enabled ITF 6 precedes 6 byte Interleaved 2 of 5 barcode Code Programming OFF Disable ITF 6 User Selection Pro CMD 0405110 ITF 6 Read Do Not Transmit Check Digit Pro CMD 0405120 ITF 6 Read Transmit Check Digit Pro CMD 0405130 For instance when ITF 6 is enabled and Interleaved 2 of 5 is disabled the ITF 6 and 6 bytes Interleaved 2 of 5 with check digit can be read but other Interleaved 2 of 5 can not a Page 65 Symbols Tools eee Code Programming ON Load Factory Default I Code Programming OFF Load Matrix 2 of 5 Factory Default Pro CMD 0406000 Disable Enable Matrix 2 of 5 Enable Matrix 2 of 5 Pro CMD 0406020 Disable Matrix 2 of 5 Pro CMD 0406010 When the engine can not read Interleaved 2 of 5 please read Enable Interleaved 2 of 5 and try again na Page 66 Symbols R Tools Code Programming ON Select Message Length It is used to program the valid reading length of Matrix 2 of 5 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code Programming OFF Matrix 2 of 5 Message Length is defined by Min Message Length and Max Message Length Min Message Length default 4 Pro CMD 0406030 MaxMessage Length default 80 Pro CMD 0406040 1D bar code Message
70. ming OFF Load Code 11 Factory Default Pro CMD 0415000 Enable Disable Code 11 Enable Code 11 Pro CMD 0415020 Disable Code 11 Pro CMD 0415010 a Page 82 Symbols R Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 11 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code 11 Message Length is defined by Min Message Length and Max gramming OFF Code Pro n Mim Message Length default 4 Pro CMD 0415030 Max Message Length default 48 Pro CMD 0415040 1D bar code Message Length should not exceed 127 bytes If Max Message Length is less than Min Message Length it means the engine will only support barcodes of the two wA lengths If Max Message Length is equal to Min Message Length the engine will only sup port barcodes of the length read these programming codes Code Programming ON Select Min Message Length Digit Code 8 see Digit Code Save Programming see Digit Code Select Max Message Length Digit Code 1 Digit Code 2 Save Programming Code Programming OFF To set Min Message Length of Codell to 8 bytes and Max Message Length to 12 bytes E le 96 9 tM oa Page 83 Symbols Tools Code Programming ON Check Digit Code 11 may include Check Digit not compulsory following its
71. must be even If it is odd a 0 will be added as the first digit The check digit generates automatically when a barcode is produced NO Check Transmit All Pro CMD 0406050 Check Do Not Transmit Check Digit Pro CMD 0406060 Check Transmit All Pro CMD 0406070 When Check Do Not Transmit Check digit is enabled and barcode message length minus one is less than Min Message Length it will lead to an error E g Reading a 4 byte include check Digit Matrix 2 of 5 with the Min Message Length being 4 bytes and Check Do Not Transmit Check digit enabled leads to an error a Page 68 Symbols R Tools eee Code Programming ON Load Factory Default I Code Programming OFF Load Code 39 Factory Default Pro CMD 0408000 Enable Disable Code 39 Enable Code 39 Pro CMD 0408020 Disable Code 39 Pro CMD 0408010 Transmit Start amp Stop Character EI Transmission of can be selected Transmit Both Pro CMD 0408090 66 II Transmit Neither Pro CMD 0408080 a Page 69 Symbols Tools Code Programming ON Select Message Length It is used to program the valid reading length of Code 39 The engine will not send barcode message to the Host if the decoded data length does not match the valid length Code Programming OFF Code 39 Message Length is defined by Min Message Length and Max Message Length Min Message Length default 1 Pro CMD 040
72. rk number This command is used for setting the value of parameter including the longest and shortest length ofthe barcode one reading timeout setting same barcode reading delay setting sensitive value setting etc e g The command setting the one reading timeout as 3000ms 0313000 3000 The command setting the sensitive value as 10 0312040 10 3 Setting syntax 3 command equal mark hex e g 0x101a 0x2C03 This command can be used as setting the user defined prefix user defined suffix ending suffix CodelD increase or cancel the barcode length value information intercepting etc Note every two hexes in the command stand for a setting character eB Append the fixed length 4 of interleaved 2of 5 to 26 0405160 0x041a Setting the suffix information of the ending as CR LF 0310000 0x0d0a 4 Setting syntax 4 command equal mark double quotation marks If the setting information is viewable character then this mode of setting is appropriate ep The command setting the user defined prefix information as AUTO ID 0300000 AUTO ID II a Page 134 Batch Programming Produce setting code Make the command list ended with save command to a PDF417 QR code or DataMatrix For example to produce a batch command means light Always On Auto Scan change delay time to 2 seconds Disable Fixed Length of I 2 of 5 Firstly find commands as follows 0200030 Clight Always On 0302010 Auto Mode 031300
73. smit barcode message with no Prefix Suffix Enable All Prefix Suffix Allow appending Code ID prefix AIM prefix User Code Programming OFF prefix User suffix and Terminal to the barcode message Disable All Prefix Suffix Pro CMD 0311000 Enable All Prefix Suffix Pro CMD 0311010 nG Page 118 Prefix Suffix XK Tools Code Programming ON Prefix Sequences 6 options of Prefix Sequences Code Programming OFF CodeID AIM User Prefix Pro CMD 0317000 AIM User Prefix CodeID Pro CMD 0317030 CodelD User Prefix AIM Pro CMD 0317010 User Prefix CodeID AIM Pro CMD 0317040 AIM CodeID User Prefix Pro CMD 0317020 User Prefix AIM CodelD Pro CMD 0317050 dea Page 119 Prefix Suffix SX Tools E Code Programming ON Disable or Enable User Prefix I I User Prefix is added before barcode message For example if the user prefix is AB and the barcode message is 123 the Host receives AB123 Code Programming OFF Disable User Prefix Pro CMD 0305000 Enable User Prefix Pro CMD 0305010 Program User Prefix Enable Program User Prefix Then program user prefix byte s To end the prefix read Save programming The user prefix byte is programmed in its hex values See example below Note The maximum length for user prefix is 10 bytes Program User Prefix Pro CMD 0300000 Program CODE as user prefix The he
74. t Check Pro CMD 0402040 Do Not Transmit Check Pro CMD 0402030 UD Page 52 Symbols R Tools o Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 2 digits Addenda Code The left one in blue lines is an ordinary code The right one in red lines is the 2 digits Addenda Code Code Programming OFF EE ee TI 134 i II Ill h Disable 2 Digits Addenda Code Pro CMD 0402050 Enable 2 Digits Addenda Code Pro CMD 0402060 5 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code Picture below shows an ordinary code with a 5 digits Addenda Code The left one in blue lines 1s an ordinary code The right one in red lines is the 5 digits Addenda Code pese rmm l Em ANA 145678 DI i 11 234567 89012 Ti i Disable 5 Digits Addenda Code P MD 0402 Pro C 0402070 Enable5 Digits Addenda Code Pro CMD 0402080 Enable 2 Digits Addenda Code read an ordinary code and 2 digits Addenda Code Enable 5 Digits Addenda Code read an ordinary code and 5 digits Addenda Code Disable 2 Digits Addenda Code read an ordinary code only and ignore 2 digits Addenda Code Symbols SX Tools eee Code Programming ON Load Factory Default I Load UPC E Factory Default Pro CMD 0403000 Code Programming OFF Disable Enabl
75. twin code gramming OFF Code Pro Single QR Only Read either QR code II Twin QR Only Read both QR codes The transmission sequence is left up per QR code followed by right lower QR code Both Single amp Twin Read both QR codes If successful transmit as twin QR only Otherwise try single QR only Single QR Only Pro CMD 0502070 Twin QR Only Pro CMD 0502080 Both Single amp Twin Pro CMD 0502090 a Page 103 Symbols SX Tools eee Code Programming ON Load Factory Default Code Programming OFF Load Aztec Factory Default ll ll Pro CMD 0503000 Enable Disable Aztec Enable Aztec Pro CMD 0503020 Disable Aztec Pro CMD 0503010 na Page 104 Symbols Tools Code Programming ON Select Message Length It is used to program the valid reading length of Aztec The engine will not send barcode message to the Host if the decoded data length does not match the valid length Aztec Message Length is defined by Min Message Length and Max Code Programming OFF Message Length ll Min Message Length default 1 Pro CMD 0503030 Max Message Length default 3832 Pro CMD 0503040 2D bar code Message Length should not exceed 65535 bytes Max Message Length should not be less than Min Message Length To read a fixed length Aztec Please program Max amp Min Message Length to the same value To set Min Message Length
76. x Suffix Ng Tools MT Code Programming ON Disable or Enable User Suffix Wi l User suffix is appended to the right of barcode message For example if user suffix is AB and the barcode message is 123 The Host receives 123AB Code Programming OFF Disable User Suffix Pro CMD 0306000 Enable User Suffix Pro CMD 0306010 Program User Suffix Read Program User Suffix Then program user suffix byte s To end the suffix read Save programming The user suffix byte is programmed in its hex values See example below Note The maximum length for user suffix is 10 bytes Program User Suffix Pro CMD 0301000 Program CODE as user suffix The hex of CODE are 0x43 0x4F 0x44 and 0x45 Read Code Programming ON Read Program User Suffix Read 4 3 4 F 4 4 4 5 in order Read Save Programming Read Code Programming OFF i Read Allow User Suffix to enable above programming CODE will appear to the right of a barcode DURAN a Page 126 Prefix Suffix Terminal SX Tools Code Programming ON Disable or Enable Terminal l Terminal is the termination for a string of barcode messages It can not be formatted like other suffix and prefix It is fixed to the right and the very end ofa barcode transmission gramming OFF Code Pro Disable Terminal Pro CMD 0309000 Enable Terminal Pro CMD 0309010 Progr
77. x of CODE are 0x43 0x4F 0x44 0x45 Read Code Programming ON Read Program User Prefix Read 4 3 4 F 4 4 4 5 in order Read Save Programming Read Code Programming OFF Read Allow User Prefix to enable above programming CODE will appear to the left of a barcode NA qu S nG Page 120 Prefix Suffix Tools AIM Automatic Identification Manufactures defines AIM prefix for many standard Code Programming ON barcode formats AIM Prefix Format AIM prefix 0 gramming OFF Code Pro Disable AIM Prefix for All Barcodes Pro CMD 0308000 Enable AIM Prefix for All Barcodes Pro CMD 0308030 a Page 121 Prefix Suffix Code ID Prefix s Tools Code Programming ON Besides AIM prefix Code ID prefix can be used to denote barcode format and can be customized The Code ID prefix MUST be one 1 or two 2 visible English letters Code Programming OFF Allow Code ID Prefix Pro CMD 0307010 No Code ID Prefix Pro CMD 0307000 Code ID Default All Bar codes Load Code ID Factory Default Pro CMD 0307020 a Page 122 Prefix Suffix Code ID Prefix SN Tools Code Programming ON Modify Code ID See the examples below for how to modify a code ID and restore factory default code ID Modify PDF417 Code ID to be p hex value is 0x70 Code Programming OFF Las ple Read Code Programming ON 2 Read Modify PD

2DScan FX100 Barcode Scanner Scanner User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents