Click on the
Contents
1. 11 Technical Parameters 12 Important notice e In this instruction for use contains about the installment and the use aspect important information of the LED moving head When installing and using you need to look this usage instruction strictly e Before open the LED moving head and if you want to do the repair work please make sure the power source is at the separation condition e Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer or dealer Attention Unceasingly carries on the product improvement about our company the policy in this instruction booklet carries the data will have the possibility to be able to change in the future when no longer separate notice change matters concerned Our company retains when the product improvement changes the related specification the authority This instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy also cannot the related consequence which causes regarding these information be respons2. Gy Porn LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Channel List nn nn tete kel ze sen sen Cammie oss cn ser sen namme joss EN Strobe 10 255 255 Strobe Strobe speed CAE RG bottom color strobe bottom color strobe LI Marco Strobe CA Marco speed Full Functions Jumping effect Gradually effect Marco Effect e effect CINCA xo pew nen nen yo E pa ou No Functions System reset www mjledlighting com PIN Nn nm nin h na atin Ee ES SCH Gy rn LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Technical Parameters Construction Composite plastic die casting aluminum Voltage ACIOV 240V 50 60Hz Power Consumption 360W 220V LED Bulbs 3W 108LEDs Red 18pcs Green 36pcs Blue 36pcs White 1 8pcs LED Current 750mA LED Lifetime 50000Hours Colors RGBW color mixing Adjusts the light 0 100 electron adjusts the light various colors may alone move also may mix the color tone Strobe 1 25 second high speed strobe but single color Mixes the color strobe Head Movement Pan 540 Tilt 270 with auto position correction and electronic replacement function Beam Angle 25 Control mode DMX 512 Stand alone mode Self test mode Sound Master slave DMX Channel 9CH 11CH 15CH Control Panel LCD display IP Grade IP20 Work Environment Temperature 20 C 40 C Other Functions Pan and Tilt speed adjustable Fan automatic control funct
3. ENTER will show slave running Show DMX512 mode press ENTER will show main screen running status Press ENTER button to save and quit Press MENU button to quit no saving a a te E gt Information 1 Press Menu button to information confirm by press ENTER button It will show Power On Hours Power this time Head Sensor Software Version 2 Press ENTER button to save and quit Press MENU button to quit no saving gt Reset 1 Press Menu button to Reset confirm by press ENTER button it shows reset Maintenance To prolong the life of the projector some maintenance work has to be done to ensure the LED optical system in good condition If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification Should these be damaged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating Should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not call a qualified technician yx Any maintenance work should only be carried out by qualified technicians www mjledlighting com Gy Mops TED Lieke LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Keeping The Product Cle
4. 3 MJ 1006 User Manual ver2 0 2 Show Pan invert Choose menu by pressing UP amp DWON button will show pan swap correcting by ENTER Button 3 Show Tilt invert Choose menu by pressing gt UP amp DWON button will show tilt Swap and tilt DMX swap correcting by ENTER Button 4 Show Dimmer invert Choose menu by pressing UP DWON button will show Dimmer Swap and dimmer invert correcting by ENTER Button 5 Press ENTER button to save and quit Press MENU button to quit no saving gt Display options settings 1 Press Menu button to Set display option Will show languages and display invert functions confirm by press ENTER button 2 Show languages selections Choose menu by pressing gt UP amp DWON button will show English and Chinese functions correcting by ENTER Button 3 Show display invert functions Choose menu by pressing UP amp DWON button will show display invert on and display invert off correcting by ENTER Button 4 Press ENTER button to save and quit Press MENU button to quit no saving gt Work modes Press Menu button to Set work modes confirm by press ENTER button Show DEMO modes 1 press ENTER button Will show program demo Show DEMO modes correct by pressing ENTER button Will show modes running Show sound mode press ENTER will show sound control running Show slave mode press
5. CORD i ee if i RE NN AN rough this orsafety i a at y HOLE FOR SAFETY CORD nn ee A PIPA amp SSL IGHT HOOK Soa SS KA Pa OS A a is gt a 2 0 Use lpes clamp and safety cord need to purchase Use clamp fix with light hook which in the packing box with light then use screw install to the bottom of lamp Hang the fixture on the structure and fasten the screws attached to each clamp Make sure the light is installed reliable and confirm the light which you fixed is strong enough for hanging the light Base on safety reason please according to the above picture using safety wire cross the light to make it strong enough again Warning 1 Hook and clamp only use for hanging the light Do not use clamp as a tool to move fixtures 2 Base on safety reason please use the safety cord which can afford the weight ten times of lamp through Insurance hole for auxiliary hanging 3 Don t use the handle of the moving head light to fixed or lift Power Code Connection Connect the power cord as follows L live brown E earth yellow green N neutral blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector It 1s recommended that each projector be supplied separately so that they may be individually switched on and off A It is essential that each projector is correctly earthed and the electrical installation conf
6. LED Moving Head Light MJ 1006 User Manual Thank you for choosing our LED moving head light For the sake of your safety Please read and follow these instructions carefully and keep this manual in a safe place for future reference Gy Mops TED Lieke LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Catalogue Chapter Page Safe Usage Of The Product 3 Install The Equipment 4 Power Code Connection a mea 4 DMX Connection 5 DMX Terminator 6 Function Set 7 e e e 6 Operation Menu a e 7 Maintenance e 9 Keeping The Product Clean 10 Trouble Shooting 10 Equipment and Appendix 10 Channel List
7. an To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days LED lens should also be regularly cleaned to maintain an optimum light output Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used for cleaning It is recommended to clean the external optics at least once every 15 days gt Do not use any organic solvent e g alcohol to clean housing of the apparatus Trouble Shooting The LED moving head light doesn t switch Check the fuse the power socket on Although shines but the LED moving head Check the digital start address and lamp doesn t accept the instruction of the also check the connection situation of controller the communication control line intermittently is whether normal well or broken The light beam appears gloomily Check that the heat dissipation system is running normally or Inspect the optics part is whether clean yx Other maintain work should by the specialist which has the experience to carry on Equipment and Appendix The packing list of this light as follows Y Led moving head light pcs yx Power Cable pcs yx Signal Cable Ipcs vx Light Hook Ipcs yx M10 Screw 2pcs 7 The Product of Instruction Ipcs www mjledlighting com
8. ible www mjledlighting com N rr LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 SAFE USAGE OF THE PRODUCT When unpacking and before disposing of the carton check there is no transportation damage before using the product Should there be any damage caused by transportation consult your dealer and do not use the apparatus The product is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The product is not designed or intended to be mounted directly on to inflammable surfaces The product is only intended for installation operation and maintenance by professional person The product must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not product the beam onto inflammable surfaces minimum distance is 5m 5m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this dev
9. ice to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep the optical system clean Do not touch the LED lens with bare hands The product should always be installed with a secondary safety fixing On the projector base brink there 1s a hole for the safety cord provided It should be attached as shown in installing the projector section LED lens shall be changed if they have become visibly damaged to such an extent that their TR ES ISI A N AD 44 MASA A effectiveness is impaired for example by cracks or deep scratches Exterior surface temperatures of the luminaire after 5 minutes operation is 40 C when steady state is achieved 50 C There is no user serviceable parts inside the projector do not open the housing and never operate the product with the covers removed If you have any questions don t hesitate to consult your dealer or manufacturer Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work www mjledlighting com ay Maps TED Lighting LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Install The Equipment Ei a __ SAFETY CORD a RN A WARNING a e pn ae e a y n oO ji En ei a yi a n o pass the SAFETY
10. ion Display LED lamps and lanterns use time Menu inversion Net weight 9 5KG Gross Weight 11 3 kg Package Size 42 x 33 x 46cm Light Size see it below 240 mm p n i IR AS J Fi Y S mm FT gan SO J TTS Y y j T I ml www mjledlighting com
11. orms to all relevant standards www mjledlighting com Gy mess TED Lighting LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 DMX Connection DMX OUT DMX IN DMX 512 3 PIN DMX OUT DMX IN PIN FUNCTION AE 5 PIN o 0 o 0 4 DATA oe 0 40 4 NIC N C Connection between the controller and a projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin which are included with the projector XLR plugs and sockets The XLR s are connected as shown in the figure above Note Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The XLED 590 accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below Ni AS ee eS aa J DMXIN DMXOUT DMX CONTROLLER DMX TERMINATOR www mjledlighting com Cy rn LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 DMX Terminator In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminato
12. peed speed ee leer Pan swap Pan swap off nn Jeen www mjledlighting com ty s LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Master show Work Modes BB Demo Modes 1 BB Master Running Demo Modes 2 CD KKK Sound Running Sound Mode KKK Slave Running Slave Mode gt FAR DMX512 Mode DMX512 Mode Pover On tours C e hour Poner tine Wine Cc Pernu gt DMX512 Address code Settings 1 Press Menu button to Set DMX Address to confirm by press ENTER button 2 Show Set DMX address DMX address 001 correct by pressing UP amp DOWN button 3 Press ENTER button to save and quit Press MENU button to quit no saving gt Config Settings 1 Press Menu button to Config Settings and choose channel quantity select it will be show Standard Extended Short three mode to confirm by press ENTER button 2 Show Fan Settings choose menu by pressing UP 4DWON button will show AUTO speed and high speed correcting by UP DOWN Button 3 Show temperature Settings and press the menu choose set the temperature 4 Press ENTER button to save and quit Press MENU button to quit no saving gt Option Settings 1 Press Menu button to choose Options Settings it will be show Pan invert Tilt Invert and Dimmer invert three options confirm by press ENTER button www mjledlighting com Oy Mega LEO Lighting LED Moving Head Wash 108
13. r This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below DMX TERMINATOR CONNECTION 3 ef Connect a 120 OHM resistor e 08 l l Va across pins 2 and 3 in an XLR plug 100 BI and insert it into the DMX out socket y d PIN on the last unit in the chain ne 5 PIN XLR en 3 PIN XLR Function Set OG6OO MENU DOWN UP ENTER Use button switch and LCD display can set the address code and function code easily Check or modify lighting function settings Press ENTER button LCD display panel will display function menu of lighting Function operation menu all have corresponding submenu Each menu all represent the specific functions of lamps specific see below operation menu section Set or browse function setting of lamp press UP or DOWN key Press ENTER key to save your changes or to ENTER submenu press UP or DOWN can change value Plus or reduce number According to the MENU key to return to the last menu If do not press MENU key system will return to display state automatic www mjledlighting com Gy Mops TED Lng LED Moving Head Wash 1083 MJ 1006 User Manual ver2 0 Operation Menu DMX Addr set DMX Address 001 512 gt oes Short High s
Download Pdf Manuals
Related Search