Manual DVM-HDBT-SCAL51
Contents
1. and connect to ground and connects to signal and connect to ground and connects to signal Switch to MIC Dynamic Microphone 48V LLINE amp 9 L 2 Balanced connection connects to positive connects to negative and connects to ground Switch to MIC Dynamic Microphone 4 MIC 48V CLINE gt LINE input LINE input has a low frequency characteristics and wide frequency response 7 Compact Scaler Switcher with PoC When switch to LINE the microphone input is used for connecting with line audio or wireless microphone output There are two different connection methods 1 Unbalanced connection and connect to ground and connects to signal and connect to ground and connects to signal MIC j line audio or wireless microphone Q 2 amp 9 H 11 connects to negative and 48V CLINE has 2 Balanced connection connects to positive connects to ground MIC Switch to LINE NN 1 line audio or wireless microphone 48V CLINE 3 5 Application SCAL51 has a good application in various occasions such as computer realm monitoring conference room big screen displaying television education command amp control center and smart home etc 4 System Operations 4 1 Operations of Front Panel Butto2. Cut off the power of SCAL51 then reboot As SCAL51 is in auto switching mode it will choose INPUT 2 to output 4 1 3 Volume Adjusting Not in OSD menu press VOL to decrease line volume VOL to increase Not in OSD menu press MIC to decrease MIC volume MIC to increase 4 1 4 Used in OSD Menu Press MENU button to enter in OSD menu and use UP DWON LEFT RIGHT button to navigate press ENTER button to confirm selection MENU button also can be used to exit present menu level by level until exit the OSD menu 4 1 5 Software updating SCAL51 supports software updating via USB flash disk Procedures 1 Copy the file MERGE 51T bin to the root directory of a USB flash disk Make sure the file is copied to the root directory for normal use 2 Plug the USB flash disk to the SCAL51 USB port on its front panel 3 Press the button MENU for 7 seconds or more to update the software automatically Or press this button for 1 second to open the OSD menu Option Select Software Update to enter in update procedure Or send command 50689 to update software 10 Compact Scaler Switcher with PoC 4 2 Operations of IR 4 2 1 IR Remote As IR signal can be transmitted bi directionally between SCAL51 and DVM HDBT RXLPOC it is able to use the IR remote at the far end to control SCAL51 or HDMI source devices via CEC function buttons D Standby button Enter exit standby mode QD 2 Input channel selection butto
3. gt 1x User Manual Notes Please confirm if the product and the accessories are all included if not please contact with the dealers 2 Product Appearance 2 1 SCAL51 Front Panel D Power indicator Illuminate red when power on turn green in standby mode 2 LCD screen Show real time system working status 3 SOURCE AUTO Used as video source selection button press to select one source press again to select next source switching circularly between HDMI1 HDMI2 HDMI3 VGA1 and VGA2 The LCD screen will show the name of selected source Used as switching mode selection button press and hold for 7 seconds or more to enter in Auto switching mode press and hold for 7 seconds or more again to enter in Manual switching mode Note Setting any VGA port to AV or YPbPr in Manual switching mode the system will not be able to enter in Auto switching mode While in Auto switching mode setting any VGA port to AV or YPbPr will automatically enter in Manual switching mode and the Compact Scaler Switcher with PoC LCD screen and RS232 control software will prompt Not support ENTER Confirm selection in menu 6 RESO AUTO Used as output resolution manual switching button select among 1920x1200 1920x1080 1600x1200 1360x768 1280x800 1280x720 1024x768 Used as output resolution switching mode selection button press and hold for 7 seconds or more to enter in Auto switching mode press and hold for 7 seconds o
4. Control local device from remote Control SCAL51 or local device from local through corresponding IR remote 12 Compact Scaler Switcher with PoC AUDIO INPUT HDMI 1 HDMI 2 HDMI 3 VGA1 VGA2 Gi IR Receiver IR Transmitter HDTV X A gt IR Remote 4 3 Operations of CEC Function SCAL51 supports CEC it can be turned on off by sending RS232 commands or OSD menu operations The default setting is ON Commands pertaining to CEC 50686 enable CEC and 50687 disable CEC HDMI INPUT ports 1 3 support CEC if the connected source devices also support CEC and their CEC are on users can control the source device via the IR remote of SCAL51 The working status related to CEC and STANDBY is showed as below Press STANDBY button on IR remote SCAL51 enters in standby mode so do all HDMI source devices Press STANDBY button again on IR remote SCAL51 exits standby mode the HDMI source devices start working too CEC on Standby on CEC on Standbv off Press STANDBY button on IR remote SCAL51 enters n in standby mode HDMI 1 3 source devices keep on Use CEC function buttons A V lt 4 gt and OK buttons on CEC on IR remote to control HDMI source devices include play pause fast forward fast reverse and operations in menu CEC off Unable to control HDMI source devices through IR remote 13 Compact Scaler Switcher with PoC IR Receiver a IR Remote of S
5. amp MIC audio MIC Unmute 50695 Disable Mic precedence 16 Compact Scaler Switcher with PoC Command 50696 50724 50725 508xx 50706 50707 50708 50709 50710 50711 50619 50626 50627 50628 50629 50620 Check Mic precedence status MIC volume up MIC volume down Set MIC volume Choose embedded audio as HDMI 1 audio input Choose external audio as HDMI 1 audio input Choose embedded audio as HDMI 2 audio input Choose external audio as HDMI 2 audio input Choose embedded audio as HDMI 3 audio input Choose external audio as HDMI 3 audio input Mic precedence XXXX XXXX enable disable MIC Volume xx xx 00 60 MIC Volume xx xx 00 60 MIC Volume xx xx 00 60 HDMI 1 Audio from Embedded HDMI 1 Audio from LINE HDMI 2 Audio from Embedded HDMI 2 Audio from LINE HDMI 3 Audio from Embedded HDMI 3 Audio from LINE Resolution Commands Change the resolution to 1360X768 Change the resolution to 1024X768 XGA Change the resolution to 1280X720 720P Change the resolution to 1280X800 WXGA Change the resolution to 1920X1080 1080P Change the resolution to1920X1200 WUXGA 17 Resolution 1360x768 Resolution 1024x768 Resolution 1280x720 Resolution 1280x800 Resolution 1920x1080 Resolution 1920x1200 Compact Scaler Switcher with PoC Change the resolution to1600X1200 Resolution 1600x1200 UXGA 50621 Setup Comma
6. A PORT Comi Baudha 3600 Parity pNone Bute 8 stop Fest Monitoring area indicates if the command sent works Clear Save To File Hex View Stop View Auto Clear View Mew Line Hes Send Mode Auto Send oad File Interval 1000 ms ies Command Sending area Counter Reset Clear 2013 05 08 14 03 35 Send Receive N Please set the parameters of COM number bound rate data bit stop bit and the parity bit correctly and then you are able to send command in Command Sending Area 15 Compact Scaler Switcher with PoC 4 4 3 RS232 Communication Commands Communication protocol RS232 Communication Protocol Baud rate 9600 Data bit 8 Stop bit 1 Parity bit none Command Feedback Example 50701 Switch to HDMI 1 50702 Switch to HDMI 2 50703 Switch to HDMI 3 50704 Switch to VGA 1 YPbPr 1 AV 1 50705 Switch to VGA 2 YPbPr 2 AV 2 50680 Input 4 Set amp Switch to VGA 1 50681 Input 4 Set amp Switch to AV 1 50682 Input 4 Set amp Switch to AV 1 50683 Input 5 Set amp Switch to VGA 2 50684 Input 5 Set amp Switch to YPbPr 2 50685 Input 5 Set amp Switch to AV 2 50785 Auto Switching 50786 Disable auto switching Manual Switching Audio Commands 50600 LINE Mute 50601 LINE Unmute 50602 LINE Volume xx xx 00 60 50603 LINE Volume xx xx 00 60 LINE Mute 50720 Mute LINE audio amp MIC audio MIC Mute l l LINE Unmute 50721 Unmute LINE audio
7. Check whether the MIC audio is mute 50752 i MIC Mute Unmute or no Display status including MIC LINE 50783 audio Resolution Output Audio m on off Manual Auto switching modes 21 Compact Scaler Switcher with PoC Resolution XXXX Digital Sound Ouput XXXX Switch status XXXX Adjustment Commands 5067896 Enter Output Position Adjust 50679 Exit Output Position Adjust 50670 Output Position Adjust X xx 50671 Output Position Adjust X xx 50672 Output Position Adjust Y XX 50673 Output Position Adjust Y xx Stretch left from left side increase 50674 Output Width Adjust xx image width Pull right from left side decrease 50675 Output Width Adjust xx image width Stretch upwards from bottom side l l 50676 l l Output Height Adjust xx decrease image height Stretch downwards from bottom side l l 50677 l l l Output Height Adjust xx increase image height 50730 Turn off HDMI output HDMI power off 50731 Turn on HDMI output HDMI power on 50732 Turn off HDBT output HDBT power off 50733 Turn on HDBT output HDBT power on Turn on HDMI amp HDBT output 50734 HDMI HDBT power on synchronously 22 Compact Scaler Switcher with PoC Note 1 Turn on off HDCP auto management by sending serial commands a When HDCP is set to active whether output source is with HDCP depends on input source If the input source is with HDCP so is the output and vice versa 2 When HDCP is set to Ma
8. Secondly send command 5078896 via RS232 communication software Lastly send the right command to control SCAL51 Connect as below AUDIO INPUT HDMI 1 HDMI 2 HDM 3 Oo O O VIDEO INPUT Control SCAL51 from local e Control SCAL51 from remote 24 Compact Scaler Switcher with PoC Firstly connect the RS232 port of far end RS232 device to RS232 port of PC Secondly send command 50788 via RS232 communication software Lastly send the right command to control SCAL51 Connect as below AUDIO INPUT IRIN FIRMWARE RS232 rmm STE 0 1510 SF yay je IL RIL RIL RIL RIL RIL RI Tx Rx C3 C5 C5 07 eL Jo e pons OUTPUT VIDEO input S ec i Control SCAL51 from remote 4 5 Operations in OSD Menu SCAL51 provides a powerful OSD operation menu contains 4 parts optional settings image settings audio settings and system setting etc Press MENU button on front panel or MENU button on IR remote send command 5061696 to enter in OSD menu so it is able to do some settings through the OSD menu 4 5 1 Option Includes Output Adjust Input4 5 Select HDMI1 2 3 Audio select and Software Update USB 25 Compact Scaler Switcher with PoC Output Adjust Input4 Select VGA 1 Input5 Select VGA 2 d HDMI1 Audio Embedded OPTION HDMI2 Audio Embedded meh HDMI3 Audio Embedded Software Update USB Output Adjust Adjust output image position X horizontal direction an
9. force ends of the optical cable It can cause malfunction Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning Unplug the power cord when left unused for a long period of time Information on disposal for scrapped devices do not burn or mix with general household waste please treat them as normal electrical wastes Compact Scaler Switcher with PoC NOTICE 1 Please read this user manual carefully before using this product 2 The item PoC is short for Power over Cable and when the power adapter is connecting with DVM HDBT RXLPOC SCAL51 can t be energized through PoC The receiver works with SCAL51 can only be DVM HDBT RXLPOC 4 The item far end means the device e g display device 3 party RS232 device etc connected with DVM HDBT RXLPOC Take notice to 4 6 Instructions of VGA Converting Cable when using Pictures shown in this manual are for reference only different model and specifications are subject to real product This manual is for operation instruction only not for any maintenance usage The functions described in this version are updated till January 2015 Any changes of functions and parameters since then will be informed separately Please refer to the dealers for the latest details This manual is copyright Sommer cable GmbH All rights reserved No part of this publication may be copied or reproduced without the prior written consent of Sommer ca
10. C51T e AUDIO INPUT IRIN FIRMWARE RS232 DC 12V re m 0000 O10 r4 ry IL RIL RIL RIL RIL RIL RI Tx Rx 5 c5 c5 oe Jj Ma o oo vipEOINPUT OUTPUT f I I tg OF Cg DVD Signal Source DVD Signal Source DVD Signal Source CEC Control HDMI source devices by IR remote of SCAL51 4 4 Operations of RS232 Control As RS232 can be transmitted bi directionally between SCAL51 and DVM HDBT RXLPOC so it is able to control a third party RS232 device from local or control SCAL51 from remote When to control a third party RS232 device the baud rate of this device should be 2400 4800 9600 19200 38400 57600 or 115200 4 4 1 Installation uninstallation of RS232 Control Software e Installation Copy the control software file to the computer connected with SCALS1 e Uninstallation Delete all the control software files in corresponding file path 4 4 2 Basic Settings First to connect SCAL51 with all input devices and output devices needed then to connect it with a computer which is installed with RS232 control software Double click the software icon to run this software Here we take the software CommWatch exe as example The icon is showed as below Commftatch exe The interface of the control software is showed as below 14 Compact Scaler Switcher with PoC Parameter Configuration area UaAl T Se 1alPort Test Tool 1 0 HTITP SL CON CH
11. Cannot control the device by control device e g a PC through RS232 port Cannot control the device by front panel buttons while can control it through RS232 port Cannot control the device by RS232 IR remote front panel buttons Fail connection of power cord The HDMI cable is broken at the output end The display does not support the resolution of the video source Bad grounding Wrong RS232 communication parameters Broken RS232 port The front panel buttons are locked The device has already been broken Make sure the power cord connection is good Change for another HDMI cable which is in good working condition Switch again Manage the EDID data manually to make the resolution of the video source automatically compliant with the output resolution Check the grounding and make sure it is connected well Type in correct RS232 communication parameters Send it to authorized dealer for checking Send command 50605 to unlock the front panel buttons Send it to authorized dealer for repairing If your problem persists after following the above troubleshooting steps seek further help from authorized dealer or our technical support 33 Compact Scaler Switcher with PoC 8 After sales Service If there appear some problems when running SCAL51 please check and deal with the problems referring to this user manual Any transport costs are borne by the users durin
12. MIC level and connect right microphone to MIC input port MIC audio will be transmitted to AUDIO OUTPUT port and mixed with source audio Step9 Connect DC12V power adaptor to the power port DVM HDBT RXLPOC is able to get power from SCAL51 with PoC function Note SCAL51 supports unidirectional PoC i e If the power adapter is connecting with SCAL51 DVM HDBT RXLPOC can get power from SCAL51 but when the power adapter is connecting with DVM HDBT RXLPOC SCAL51 can not get power from DVM HDBT RXLPOC 3 4 Connection of Microphone SCAL51 provides with one 3 level microphone input port to accommodate different microphone input modes including 48V phantom power mode MIC mode amp LINE mode gt 48V phantom power input 48V phantom power input has a good frequency characteristic high input impedance and high sensitivity When switching to 48V the MIC input will provide a 48V phantom power This is only used for condenser microphone di 9 Connect the microphone in this way connects to positive connects to negative 6 Compact Scaler Switcher with PoC and to ground Switch to 48V Condenser Microphone 48V CLINE gt MIC input MIC input has a low frequency characteristics and wide frequency response When switch to MIC the microphone input is used for connecting with dynamic microphone There are two different connection methods 1 Unbalanced connection
13. O Source A Operation Examples 1 Via front panel buttons amp OSD Press MENU button on front panel to enter in OSD and then enter in OPTION setting menu set INPUT 4 Select to AV1 and INPUT 5 Select to AV2 After setting press SOURCE AUTO button on front panel to switch to AV1 or AV2 source 2 Via RS232 commands Send command 50682 or 50685 to switch to YPbPr1 or YPbPr2 source 3 Via IR remote amp OSD Press MENU button on IR remote to enter in OSD and then enter in OPTION setting menu set INPUT 4 Select to AV1 and INPUT 5 Select to AV2 After setting press INPUT 4 or INPUT 5 button to switch to AV1 or AV2 source B Connecting the VGA converting cable like this Blue lt Red gt C VIDEO 20 utin Green 5 Specification Video Input Video Output 3 HDMI 1 HDMI PH 2 VGA MEE 1 HDBaseT Input 3 female HDMI Output 1 female HDMI Connector 2 female VGA 15 pin Connector 1 RJ45 l HDMI YPbPr C video l 1 HDMI Video Signal Video Signal 1 HDBaseT Input 1 IR IN Output 5 IR OUT ie 3 5mm mini jack PUE 3 5mm mini jack Connector Connector Video General 1920x1200 HDMI 4 95Gbps 1 65Gb ps per color Resolution Mi i36 76g Bandwidth C Video 150MHz YPbPr 170MHz 1280x800 1280x720 rer 30 Compact Scaler Switcher with PoC Maximum Video Gain OdB a a en Level Compliant with DVI amp HDMI 1 3 standards Audio Input Audio output 3 Dual mono stereo audio f
14. SOMMER CABLE gt Gg User Manual DVM HDBT SCAL51 DVM 5x1 Switcher Scaler 1 2 19 1HE All Rights Reserved Version DVM HDBT SCAL51_2015V1 8 Compact Scaler Switcher with PoC SAFETY PRECAUTIONS To insure the best from the product please read all instructions carefully before using the device Save this manual for further reference Unpack the equipment carefully and save the original box and packing material for possible future shipment Follow basic safety precautions to reduce the risk of fire electrical shock and injury to persons Do not dismantle the housing or modify the module It may result in electrical shock or burn Using supplies or parts not meeting the products specifications may cause damage deterioration or malfunction Refer all servicing to qualified service personnel To prevent fire or shock hazard do not expose the unit to rain moisture or install this product near water Do not put any heavy items on the extension cable in case of extrusion Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards Install the device in a place with fine ventilation to avoid damage caused by overheat Keep the module away from liquids Spillage into the housing may result in fire electrical shock or equipment damage If an object or liquid falls or spills on to the housing unplug the module immediately Do not twist or pull by
15. ble GmbH All product function is valid till 2015 01 12 Compact Scaler Switcher with PoC Contents T MOGUCOM ee ee aa aan RR NOTER 1 1 1 Introduction to SCALES Er iod E eoe ea ddl sa Ela 1 U 24e AEM S oic testa huida her A arse aea dcs nen ed vid aite EAT 1 Tis PACKAGES ISU PH een 1 Z ProductADDeal ari GG nennen 2 2 SCALOI TBIODPPanelssescs eii tad nera ecd aid 2 22 OGAL SI Rear Panelessis eiserne 4 3 System COnNeellon u u e 5 Onl USAGE PrecalltlOliS aan ae 5 3 2 Sysle1 Diagfales esse ee 5 3 0 Connection Precedente ein 6 3 4 Connection of Microphone 222000220002ennenennennnnnnnnnennnnnnnnnnnnnnnennnne nn 6 a oy 2 1618 eio EHE T ne een 8 4A System OPE NAL ONS zu sea ee eier 8 4 1 Operations of Front Panel Buttons 2u002220002000nennennnnennnnennnnn nennen 8 41 1 Resolution AQJUSING ae aaa a a ie 8 4 1 2 Switching Operations us020440Bnennennnnne nennen nenne nnnnnne nennen nennen nnnnnen 9 41 3 VOUME AQJUSING ae ee 10 4 1 4 Used in OSD Menu u 2222002200000nennnonnnnnn nennen nennen nennen nnnnne nennen 10 4 1 3 Soflware pdatling iwi Accs Re hou stes Ae ea 10 4 2 Operations On IR euere ee 11 LUN MIS aei ce Ee 11 42 2 IR Operalons aiiud idet ent accom en er ne ear 12 4 3 Operations of CEC Function sseeessessssessseeennenenn nnne nnne nnns 13 4 4 Operati
16. d Y vertical direction r Input4 Select Select video source format for VGA input includes AV 1 C video signal VGA 1 VGA signal and YPbPr 1 Component video signal Input5 Select Select video source for VGA input includes AV 2 C video signal VGA 2 VGA signal and YPbPr 2 Component video signal For INPUT4 amp INPUT5 when change for new format signal 1 Firstly please select a format through this menu the signal format changed while the video source is still the same 2 Secondly switch off the present signal channel e g switch to another channel 3 Thirdly switch to channel INPUTA INPUTS again HDMI1 Audio Select switch between Embedded and Line to choose the desired audio output port for HDMI1 HDMI2 Audio Select switch between Embedded and Line to choose the desired audio output port for HDMI2 HDMI3 Audio Select switch between Embedded and Line to choose the desired audio output port for HDMI3 Software Update USB Insert the USB flash disk with updating file to USB port of 26 Compact Scaler Switcher with PoC SCAL51 to update the software through this menu 4 5 2 Picture Including Picture Mode Color Temperature Aspect Ratio Noise Reduction Screen and Color Range Please check the picture below Picture Mode Standard Color Temperature Aspect Ratio _ PICTURE Screen Picture mode Includes Dynamic Standard Mild and User Color Temperature Includes Cool M
17. edium Warm and User And only in User mode it is able to set values for Red Green and Blue RGB Aspect Ratio Includes Native 4 3 16 9 Zoom1 Zoom2 Just Scan and Panorama VGA format only supports 4 3 16 9 and Panorama Noise Reduction not for VGA format Includes Off Low Middle High and Default Screen not for HDMI source Includes Auto Adjust Horizontal Vertical Size and Phase Color Range not fo ormat use ENTER button to select the desired color range 4 5 3 Sound Including Sound Mode Surround Sound and EQ Please check the picture below 27 Compact Scaler Switcher with PoC Surround Sound Sound mode Includes Standard Music Movie Sports and User Only User mode supports to set treble and bass Surround Sound Includes Off Surround and SRS Trusurround XT EQ To adjust the sound balance 4 5 4 Setup Including OSD Language Restore Factory Default Blending HDMI CEC OSD Duration and version inquiry Restore Factory Default Blending HDMI CEC OSD Duration Off VERSION 1 1 6 Compact Scaler Switcher with PoC OSD Language Supports 7 languages including English default Chinese etc Restore Factory Default Restores to original system state Blending Includes Low Middle High and Off Use ENTER button to select HDMI CEC Enable disable CEC and auto standby function Default CEC on STANDBY on Only when CEC is on will it be able to set auto standby status OSD Durati
18. g the warranty 1 Product Limited Warranty Sommer cable GmbH warrants that its products will be free from defects in materials and workmanship for three years which starts from the first day you buy this product The purchase invoice shall prevail Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service 2 What the warranty does not cover e Warranty expiration e Factory applied serial number has been altered or removed from the product e Damage deterioration or malfunction caused by Normal wear and tear Use of supplies or parts not meeting our specifications No certificate or invoice as the proof of warranty The product model showed on the warranty card does not match with the model of the product for repairing or had been altered Damage caused by force majeure Servicing not authorized by Sommer cable GmbH Any other causes which does not relate to a product defect e Delivery installation or labor charges for installation or setup of the product 3 Technical Support Email to our after sales department or make a call please inform us the following information about your cases Product version and name e Detailed failure situations e The formation of the cases Remarks For any questions or problems please try to get help from your local distributor or email Sommer cable at info s
19. iant with multiple video signals SCAL51 scales amp switches any video signal to HDMI output and HDBaseT output Supports PoC connects with DVM HDBT RXLPOC max transmission distance is 60 meters And with 1 IR IN 5 IR OUT amp 1 RS232 IR amp RS232 signal can be transmitted bi directionally between SCAL51 and DVM HDBT RXLPOC 1 2 Features Compliant with HDCP Supports CEC with commands to enable disable this function Supports video source auto switching function Bi directional IR amp RS232 control Output resolutions selectable to assure preferred output and supports various output resolutions such as 1920x1200 1920x1080 1600x1200 1360x768 1280x800 1280x720 1024x768 VGA video supports C video YPbPr and VGA Supports online software upgrading 48V phantom power to support condenser microphone MIC port supports balance unbalance signal suppress the external noise effectively 3 level MIC input supports condenser microphone dynamic microphone and wireless microphone e Controllable via button IR amp RS232 Powerful OSD function 1 3 Package List gt 1xSCAL51 2 x Mounting ears for SCAL51 5 x Screws black color 7 x Captive screw connectors VV V WV 1 x IR receiver with carrier wave Compact Scaler Switcher with PoC gt 1xIR emitter 2 x VGA to YPbPr cables 1 x RS232 cable 8 x Plastic cushions V VV WV 1 x IR remote Cell battery is not included gt 1x Power Adapter DC 12V
20. ler 50697 Exit standby mode Enter standby mode Software update LU Reset to factory defaults Menu Commands 50616 MENU button enter OSD OSD Enter 50618 EXIT button exit OSD OSD Exit Inquire Commands keel LINE Volume xx xx 00 66 5063096 Check the volume level MIC Volume xx xx 00 66 Input xx xx HDMI1 HDMI2 5063196 Check the input source HDMI3 VGA1 VGA2 YPbPr1 YPbPr2 AV1 AV2 Resolution xx xx 1920 X 1200 1920 x 1080 1600 x 1200 1360 X 768 1280 x 800 1280 X 720 1024 X 768 5063396 Check the image mode Picture Mode xx xx Dynamic 20 5079796 50698 50617 50632 Check the output resolution Compact Scaler Switcher with PoC Sound Mode xx xx Standard 50634 Check the audio mode l l Music Movie Sports User Aspect Ratio xx xx 16 9 4 3 auto panorama justscan 50635 Check the image aspect ratio zoom1 zoom2 when the input source is VGA format xx can only be 4 3 16 9 or Panorama Saturation xx xx 00 99 Color Temperature xx 50640 Check the color temperature xx Cool Medium Warm User 50651 Check Volume Icon display status u Embedded Audio Output 50652 Check Digital audio output status l enable disable HDMI1 Audio from XXXX port Check the audio input sources for 50712 HDMI2 Audio from XXXX port HDMI 1 2 3 HDMI3 Audio from XXXX port Check whether the LINE audio is mute 50751 LINE Mute Unmute or not
21. ly gt Power rebooting principle SC51T offers the function to remember the last displayed signal when rebooting Once rebooted SCAL51 will automatically enter auto switching mode and then detect all inputs and memorize their connection status for future rebooting using If the last displayed signal is still available SCAL51 will output the signal If not there will be no signal on output devices gt Signal removing principle Once removing the current display signal SCAL51 will detect all input signals with priority from INPUT 1 to INPUT 5 It will transfer the signal firstly detected to be available to output devices Notice Auto switching function works only when inputting new signal removing a signal or power rebooting With any VGA port set to AV or YPbPr the system will be not able to 9 Compact Scaler Switcher with PoC enter in Auto switching mode Operation Examples Connect INPUT 2 INPUT 4 and INPUT 5 ports with source devices select INPUT 4 to outputs Press and hold for the front key SOURCE AUTO for 7 seconds or more to enter in auto switching mode No signal removing or new input SCAL51 just works in auto switching mode and take no action Output from INPUT 4 Connect INPUT 3 with a source device and then it will choose INPUT 3 to output Remove the signal of INPUT 3 SCAL51 will detect from INPUT 1 to INPUT 5 And when it detects that input 2 is available it will choose INPUT 2 to output
22. nds 50604 Lock the front panel buttons Front Panel lock 50605 Unlock the front panel buttons Front Panel Unlock 501xx LINE Volume xx xx 00 60 503xx Contrast xx xx 00 99 504xx Saturation xx xx 00 99 505xx Sharpness xx xx 00 99 Color Temperature xx Adjust the color temperature xx Cool Medium Warm User Aspect Ratio xx xx 16 9 4 3 auto panorama justscan Set the aspect ratio zoom1 zoom2 when the input source is VGA format xx can only be 4 3 16 9 or Panorama l Picture Mode xx xx dynamic 50614 Set the picture mode l standard mild user l Sound Mode xx xx standard 50615 Set SM audio mode l l music movie sports user 18 Compact Scaler Switcher with PoC Auto adjust the input parameter VGA 50606 ly VGA Input Auto only Inquire HDCP Active HDCP 50795 HDCP Manual Inquire HDCP Manual HDCP HDCP OFF ON 50767 Restore default EDID EDID initial 50768 Bypass EDID data from output to input EDID bypass Upload custom EDID data to the 50769 EDID user switcher EDID initial 50770 Inquire EDID status EDID bypass EDID user Compact Scaler Switcher with PoC EDID management copy the best EDID manage 50782 resolution data of one output to HDMI ee Enable serial control mode 1 control Scaler amp far end from local RS232 Scaler amp Remote rozon Enable serial control mode 2 control Scaler from local RS232 and far end Remote Control Sca
23. ns INPUT 1 is for HDMI1 INPUT 2 for HDMI2 INPUT 5 for VGA2 AUTO Enable disable auto switching mode 3 Volume adjusting buttons MIC turn down up MIC volume LINE turn down up line volume MIC MUTE mute unmute MIC audio LINE MUTE mute unmute line audio 4 Menu operation buttons MENU press to enter in OSD menu or used to return to previous menu EXIT exit OSD menu OK confirm button Navigation buttons UP DWON LEFT RIGHT button for value setting or page turn Buttons in area a are also able to work in CEC mode to enter the menu of HDMI source device P P ZOOM S M shortcut button to select display mode STOP MENU REV FWD J Scaler Switcher 5 Resolution selection buttons Select resolution by pressing corresponding button AUTO Enable disable auto switching mode CEC function buttons For HDMI input signal which supports CEC only Including PLAY PAUSE STOP MENU REV reverse and FWD forward Buttons in section a also work when entered CEC too 11 Compact Scaler Switcher with PoC 4 2 2 IR Operations The 5 IR OUT ports correspond to the 5 video inputs separately and the IR signals are switched following the corresponding video source 1 Control far end device from local Control SCAL51 or far end display device from local through corresponding IR remote IR Receiver E i IR Signal AUDIO INPUT HDMI3 HDMI 1 HDMi 2 VGA 1 2
24. ns Front panel buttons can be used for output resolution adjusting switching operations software updating volume adjusting and other operations in menus 4 1 1 Resolution Adjusting Resolution supports auto adjusting and manual adjusting Press and hold for RESO AUTO button for 7 seconds or more to switch between auto adjusting manual adjusting mode Note Compact Scaler Switcher with PoC 1 In auto adjusting mode SCAL51 will choose the resolution of the display device at the far end as the preferred resolution If you need to choose the resolution of local HDMI display device Cut off the power of SCAL51 and disconnect SCAL51 and DVM HDBT RXLPOC Turn on the power of SCALS1 Gets the resolution of local HDMI output device Connect DVM HDBT RXLPOC to SCALS1 2 In auto switching mode front panel button control is not available but IR and RS232 control are able to switch modes 4 1 2 Switching Operations Video signals support auto switching and manual switching Press and hold for SOURCE AUTO button for 7 seconds or more to enter in auto switching manual switching mode The display result is showed as below IN HDMI1 MANUAL IN HDMI1 AUTO 1280 X 720 1280 X 720 The display result will be showed for 2 seconds Auto switching function The auto switching mode abides by the following principles New input principle Once detecting a new input signal SCAL51 would switch to this new signal automatical
25. nual whether the output is with HDCP depends on the statue of HDCP Turn off HDCP then the output is without HDCP and vice versa 3 Screen output adjusting avails only when the screen output adjusting is on Send command 50678 to turn on 4 CEC commands with grey background avails only when CEC is on 5 MIC precedence In Mute mode if the MIC noise detecting is on the device will unmute MIC automatically given the outer noise exceeds the limit of noise detecting Send 50696 to enable MIC precedence then the device will not be able to change the mute mode no matter how loud the noise is 4 4 4 Control SCAL51 or 3rd Party Device from Local Firstly connect the RS232 port of SCAL51 to RS232 port of PC Secondly send command 50787 serial control mode 1 factory default via RS232 communication software Lastly send the right command of SCAL51 or other remote RS232 device connected in present system Connect as below 23 Compact Scaler Switcher with PoC X gt AUDIO INPUT AUDIO IROUT IRIN FIRMWARE R 232 DC 12 HDMI HDMI2 HDMIS X VGA1 VGA2 OUTPUT O O O O O O IP IL RIL RIL RIL RIL RIL RI Tx Rx f O O o Oo 715 C9 C9 C9 LL A 48V LINE HDMI 1 HDMI 2 OUTPUT VGA2 VIDEO input SA Control SCAL51 or 3rd party device from local 4 4 5 Control SCAL51 from Local or Remote Control SCAL51 from local Firstly connect the RS232 port of SCAL51 to RS232 port of PC
26. ommercable com 34 SOMMER CABLE SOMMER CABLE GmbH Humboldtstra e 32 36 75334 Straubenhardt Germany Telefon 49 0 7082 49133 0 Support Tel 49 0 7082 49133 10 Fax 49 0 7082 49133 11 E Mail info sommercable com Internet www sommercable com
27. on Includes 5 s 10 s 15 s and Off s is for Second VERSION Displays software version 4 6 Instructions of VGA Converting Cable As VGA source supports YPbPr and C video source SCAL51 provides with 2 VGA converting cables to compliant with these signals When need to select these signals as input source please switch to channel INPUT 4 or INPUT 5 and then set the signal type in OSD And then switch to other input channel and connect INPUT 4 or INPUT 5 with corresponding source device At last please switch to INPUT4 or INPUT 5 again e Connect with Component Video YPbPr Source A Operation Examples 1 Via front panel buttons amp OSD Press MENU button on front panel to enter in OSD and then enter in OPTION setting menu set INPUT 4 Select to YPbPr1 and INPUT 5 Select to YPbPr2 After setting press SOURCE AUTO button on front panel to switch to YPbPr1 or YPbPr2 source 2 Via RS232 commands Send command 50681 or 5068496 to switch to YPbPr1 or YPbPr2 source 3 Via IR remote amp OSD Press MENU button on IR remote to enter in OSD and then enter in OPTION setting menu set INPUT 4 Select to YPbPr1 and INPUT 5 Select to YPbPr2 After setting press INPUT 4 or INPUT 5 button to switch to YPbPr1 or YPbPr2 Source B Connecting the VGA converting cable like this Blue pp Red J Pr Green Y 29 Compact Scaler Switcher with PoC e Connect with Composite Video C VIDE
28. onnected before power on 3 2 System Diagram y u Sy IR Receiver Ew IR Receiver A gt N lt a ee n IR Emitter HDBaseT Audio Signal Video Signal RS232 Control Signal IR Transmitter Receiver Compact Scaler Switcher with PoC 3 3 Connection Procedure Step1 Connect HDMI source devices e g Blue ray DVD to HDMI input ports of SCAL51 with HDMI cable Connect VGA source devices e g PC to VGA input ports of SCAL51 with VGA cable Step2 Connect audio sources to corresponding AUDIO INPUT ports on SCAL51 with audio cable The audio of HDMI can be embedded or external by sending the right command Step3 Connect a HDMI display device to HDMI output port of SCAL51 with HDMI cable Step4 Connect DVM HDBT RXLPOC to HDBaseT output port of SCAL51 with twisted pair Step5 Connect speaker headphone or DVM amplifier to AUDIO OUTPUT port of SCAL51 Step6 Connect control device e g PC to RS232 port of SCAL51 or DVM HDBT RXLPOC bi directional RS232 control either end is available Step7 Both SCAL51 and DVM HDBT RXLPOC have IR IN and OUT When one model is connected with IR receiver the other model should connect with an IR transmitter For example When IR IN of SCAL51 connects with an IR receiver the IR transmitter must connect to IR OUT of DVM HDBT RXLPOC The IR signal can be transmitted bi directionally between SCAL51 and DVM HDBT RXLPOC Steps Select
29. ons of RS232 Control eessessssessssessesee senes 14 4 4 1 Installation uninstallation of RS232 Control Software 14 44 2 Basic Sellings ua a 14 4 4 3 RS232 Communication Commands eese 16 4 4 4 Control SCAL51 or 3rd Party Device from Local 23 4 4 5 Control SCAL51 from Local or ReMote ccccccsseeeeeseeeeeeaeeeeeseeeees 24 4 5 Operations in OSD Menue es ciet santo ies tto poer rino tide d n sento tain euap ees 25 Compact Scaler Switcher with PoC Aa HOO OW ee 25 19 2 PICU ns Suse e Oii hoe tet cato iode sos tu MM oci aes 27 AREE KELO T ao ME ATR PEEP E TN EEEE AAE ea Ne ante ee een 27 2 54 SOUS er ea ED Le M E E 28 4 6 Instructions of VGA Converting Cable seesseseseeeeee 29 meets t eee 30 o zig OFA ING een ens 32 7 Troubleshooting amp Maintenance ccccccssececceeececceesceceeseeecseeeeeseseesseueeesseeeeseaes 32 8 Aller sales Ser VICE facie creel ca er ee ee ee base E neue 34 Compact Scaler Switcher with PoC 1 Introduction 1 1 Introduction to SCAL51 is a compact mini scaler switcher with 5 video inputs 3 HDMI 2 VGA and 6 audio inputs 3 HDMI audio amp 2 VGA audio switched following the video 1 MIC audio input As the VGA input supports VGA YPbPr and C video so the scaler switcher is compl
30. or HDMI Input 2 Dual mono stereo Output 1 stereo audio for VGA Support C VIDEO YPbPr VGA Output Connector Input Coredo 3P captive 3 81mm 3P captive 3 81mm Input gt 10KQ Output 700 Impedance Impedance Audio General Stereo 20Hz 20K Hz Channel gt 80dB 1KHz Separation Frequency Response Control Parts Control IR remote Buttons amp Pin 2 TX 3 RX 5 Remote RS232 Configuration GND 10 40 C Humidity 10 90 8W supply power to B 5 SCAL51 and ower ower Supply pone SON Consumption RXLPOC separately 16W SCAL51 supplies power to RXLPOC Dimension W H D 220x 44x 148mm Weight 0 65Kg 31 Compact Scaler Switcher with PoC 6 Panel Drawing 220 00 mm 148 00 mm 118 00 mm 44 00mm 7 Troubleshooting amp Maintenance Protons Tome i Sune Output image with Bad quality of the Try another high quality is good No output image when No signal at the input Check with oscilloscope or switching output end multimeter if there is any signal at the input output end Fail or loose connection Make sure the connection is good The switcher is broken Send it to authorized dealer for repairing 32 Compact Scaler Switcher with PoC POWER indicator doesn t work or no respond to any operation EDID management does not work normally There is a blank screen on the display when switching Static becomes stronger when connecting the video connectors
31. r more again to enter in Manual switching mode MENU FWUPDATE Used as menu button press it to enter in OSD menu Used as software updating button press and hold for 7 seconds or more to enter in software updating procedure D VOL Used as volume down button Used as direction button NEXT in menus MIC Used as MIC volume up button Used as direction button MOVE UP in menus Q VOL Used as volume up button Used as direction button PREVIOUS in menus MIC Used as MIC volume down button Used as direction button MOVE DOWN in menus Note Pictures shown in this manual are for reference only different model and specifications are subject to real product Compact Scaler Switcher with PoC 2 2 SCAL51 Rear Panel 2 D AUDIO INPUT Including 3 HDMI audio amp 2 VGA audio inputs User can choose any one audio embedded HDMI audio or external input audio for HDMI audio input by sending RS232 commands AUDIO OUTPUT Audio output port the audio comes from the input audio corresponding to the selected video source and mixed with MIC audio IR OUT 5 in total connect with IR emitters to control local source devices or SCAL51 from remote switched along with corresponding video source IR IN Connects with IR receiver with carrier wave only to receive IR signal send by the IR remote or remote controller of other input output device FIRMWARE USB po
32. rt connects with USB flash disk or other storage which is with update file inside to update the system firmware RS232 Serial control port 3 pin captive screw connector connect with a control device such as a computer to control SCAL51 or other devices connected with DVM HDBT RXLPOC DC 12V Power port connect with DC 12V power adapter MIC a MIC port Connect with microphone b Dial switch Compact Scaler Switcher with PoC Including 3 levels 48V phantom power mode connect with condenser microphone MIC mode connect with dynamic microphone and LINE mode connect with wireless microphone or line audio Q VIDEO INPUT Video input ports include 3 HDMI inputs amp 2 VGA inputs VGA ports support YPbPr C video and VGA format Factory default is VGA format OUTPUT c HDMI local output d HDBaseT output support PoC The two ports share the same audio signal and the audio signal is mixed with MIC audio and HDMI embedded audio output audio If disabling HDMI embedded audio output there will be no audio output through these ports Note Pictures shown in this manual are for reference only different model and specifications are subject to real product 3 System Connection 3 1 Usage Precautions 1 System should be installed in a clean environment and has a prop temperature and humidity 2 All of the power switches plugs sockets and power cords should be insulated and safe 3 All devices should be c
Download Pdf Manuals
Related Search