Wilson RF Signal Detector USER GUIDE
Contents
1. RF Signal Detector Model 2E7501 Contents PUIDOSC 3 Geese ewe eae Ee oe eee ee oo ae eee oat 1 Powering Up the Detector 5 2 Understanding the LCD Screen 3 Guarantee amp Warranty 0 0 00 0c eee eee eee 6 Specifications 0 0 eee Back Cover Appearance of device and accessories may vary Note This manual contains important safety and operating information Please read and follow the instructions in this manual Failure to do so could be hazardous and result in damage to your Signal Detector Wilsonr Electronics Inc Purpose The purpose of the RF Signal Detector is to assist the installation of a Wilson Electronics Signal Booster specifically for e Mapping the frequency environment e Pointing directional antennas e Maximizing Wilson Electronics Signal Booster coverage Recommended Outside Antenna Any Outside Antenna may be used The recommended antenna for installing a Wilson Signal Booster is the antenna the Signal Booster came with Directional antennas will help the installer determine the location of a signal of interest or interferer For general frequency mapping the 304411 is recommended because it is both directional and has wide bandwidth This will allow the installer to use the RF Signal Detector without ever having to change antennas Inside this Package Velcro Stickers N Male to N Male Connector 971149 Je TNC Female to2. N Male Connector Battery Pack 971148 859996 Rubber Antenna for indoor frequency mapping 301144 Power Supply 859912 RF Signal Detector 867501 Optional Accessory Kit 308410 A Wide Band Panel Antenna 700 2700MHz 304411 B Pole Mount Assembly 901117 C 2 Extension Cable RG58 N Male to N Male 951134 A B os 4 Seal qS iti Appearance of device and accessories may vary To purchase contact Wilson Electronics Sales Department at 800 204 4104 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Frequency Mapping Finding Strongest Outdoor Signal Cell Tower RF Signal Detector Ze y p l Wide Band Directional Antenna Checking Inside Coverage Area N Inside p nel Antenna RF at Detector il l Check inside coverage before amp after installation EEE of Signal Booster system Powering Up the RF Signal Detector 1 2 Plug the AC power supply or battery pack into the RF Signal Detector input Ensure that the Outside Antenna cable or Rubber Antenna is connected to the RF Signal Detector and the connection is tight before powering up the RF Signal Detector marked 6V DC carefully to avoid damaging the center pin Plug into surge protected AC Po
3. St George UT 84790 For additional Technical Support visit www WilsonElectronics com or email tech wilsonelectronics com Phone 866 294 1660 Local 435 673 5021 Fax 435 656 2432 www twitter com WilsonCellular www facebook com WilsonCellular 111081_RF Signal Detector _Rev05_ 07 25 12
4. a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty RMA numbers may be obtained by contacting Technical Support at 866 294 1660 Disclaimer The information provided by Wilson Electronics Inc is believed to be complete and accurate However no responsibility is assumed by Wilson Electronics Inc for any business or personal losses arising from its use or for any infringements of patents or other rights of third parties that may result from its use Copyright 2012 Wilson Electronics Inc All rights reserved U S Patent Nos 7 729 669 7 486 929 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST RF Signal Detector Specifications RF Signal Detector Specifications Model Number 2E7501 Antenna connector N Type Antenna impedance 50 ohms Dimensions 5 7 x 4 2 x 1 5 inch 14 0 x 10 8 x 3 9 cm Weight 1 24 lbs a SS Maximum detectable in band signal dBm 38 Minimum detectable in band signal with 1 5MHz BW dBm 110 Minimum detectable in band signal with 1OMHz BW dBm 105 Maximum recommended RF input dBm 38 L l SSS SS SSS SS SSSSS_a___Z Power Requirements 110 240 V AC 50 60 Hz 4 2W or 6V DC 700mA amp Wilson Electronics Inc 3301 East Deseret Drive
5. are typically 5 MHz increments for 10 MHz BW Note For a list of channel options see tables on page 4 Any button may be held down to step more quickly If the RF Signal Detector is operating normally the LCD Screen will appear similar to Figure 1 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST To Find Your Wireless Providers Licensed Broadcast Frequencies 1 2 3 4 5 Go to http wireless2 fcc gov UISApp UlsSearch searchLicense jsp Look for Specialized search on right side of screen Click on Geographic Enter your region Enter a specific frequency range to narrow the search results As the signal detector indicates the downlink frequency below are the recommended frequency ranges to search for each band 700 MHz Search 728 757 850 MHz Search 869 894 1900 MHz Search 1930 1990 AWS Search 2110 2155 Click Search On the Search Results page click on the wireless provider of interest NOTE Most will show the wireless provider s name If it does not show the wireless provider s name then select the Call Sign Lease ID and then look at Contact for the wireless provider Check that the license is Active under Status Click View Frequencies or look at Associated Frequencies and Channel Block Click on th
6. e Market tab and look at the Spectrum and Market Area to verify the exact frequency that your provider is operating on in your particular county or counties Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Available Downlink Bands Channels Downlink Band Pass Bandwidth MHz _Lowest Center Pighest Gener Frequency MHz Frequency MHz 1900 MHz PCS 1930 75 1989 25 1700 2100 MHz AWS m 2110 75 2154 25 1 5 700 MHz Band 12 amp 13 728 75 755 75 About Wilson Electronics Wilson Electronics Inc has been a leader in the wireless communications industry for over 40 years The company designs and manufactures Signal Boosters Antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications both mobile marine RV vehicles and in building home office M2M With extensive experience in antenna and Signal Booster research and design the company s engineering team uses a state of the art testing laboratory including an anechoic chamber and network analyzers to fine tune antenna designs and performance For its Signal Boosters Wilson Electronics uses a double RF electrically shielded enclosure and cell tower simulators for compliance testing All products are engineered and assembled in the company s 55 000 square foot h
7. eadquarters in St George Utah Wilson Electronics has product dealers in all 50 states as well as in countries around the world Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST 30 Day Money Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30 day money back guarantee If for any reason the performance of any product is not acceptable simply return the product directly to the reseller with a dated proof of purchase 1 Year Warranty Wilson Electronics Signal Boosters are warranted for one 1 year against defects in workmanship and or materials Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase Signal Boosters may also be returned directly to the manufacturer at the consumer s expense with a dated proof of purchase and a Returned Material Authorization RMA number supplied by Wilson Electronics Wilson Electronics shall at its option either repair or replace the product Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer if located within the continental U S This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to misuse abuse neglect or mishandling that alters or damages physical or electronic properties Failure to use
8. wer Strip NOTE Utilize the velcro included in this kit to secure Battery Pack to botto side of Signal Detector Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST If the RF Signal Detector does not have a green light N or if you questions please contact Wilson Electronics Technical Support Team at 866 294 1660 or email tech wilsonelectronics com Technical Support hours are Mon Fri 7 am to 6 pm MST Understanding the LCD Screen 13 Figure 1 The Downlink Center z S Frequency is the top number on Po z the screen Units are MHZ C Wilson The Pass Bandwidth is the bottom left number on the amna mE screen Units are MHZ Lal zal Downlink Center Frequency o yt Detected Cellular Pass Bandwidth gt gt m Downlink Signal Li m A The Detected Cellular Downlink Signal Level is the bottom right number on the screen Units are RF SIGNAL DETECTOR d B m SMART TECHNOLOGY BAND BW The BAND Select button Select Select will select between downlink bands Note For a list of band options see tables on page 4 XS A The BW bandwidth Select button toggles between 1 5 MHz and 10 MHz pass bandwidth Note For filter characteristics see tables on page 4 The CH Channel Select button will step to the next channel Steps are in 1 5 MHz increments for 1 5 MHz BW Steps
Download Pdf Manuals
Related Search