HC-600 Model ODG V1 / V3 ON DEMAND COFFEE GRINDER
Contents
1. ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 4 UNPACKING AND INSTALLATION Warning All appliances technical handling operations such as installation maintenance or service should be performed by certified personnel or by your local dealer After opening the box make sure that the appliance is intact and that there is no visible damage If there is any doubt DONOT use the appliance and call your local dealer for further assistance Unpack the carton box carefully For your convenience we suggest storing all packaging materials where they can be used in the future whenever the appliance s transportation is necessary Place the grinder on a stable flat counter in a dry area away from water or water splashes Position the coffee residue tray underneath the body in front of the appliance Install the beans hopper firmly on top of the body inside the top blade holder Fasten the hopper to the appliance body by means of the supplied screw fig 4 1 Make sure that the screw is inserted completely through both holes in the hopper and in the top blade holder Fig4 1 NEVER OPERATE THE GRINDER IF THE BEAN HOPPER IS NOT FULLY SECURED IN ITS POSITION Before plugging in the electrical cord make sure o The appliance voltage and frequency rating according to the bottom cover label is the same as the supply mains o The wall socket is fitted with an efficient ground contact DONOT plug the appliance into2. e The replacement and assembly of a new set of blades is a delicate task Only skilled technical personnel should be allowed to perform blade removal and assembly e fa more thorough clean is required then the operation must be performed by skilled technician After all cleaning and replacing tasks are through make sure to assemble all of the parts and safety screws the same way as they were disconnected If anything does not fit back together or there are some leftover parts do not attempt to operate the appliance call for the assistance of your technician To ensure long lasting grinder and great fresh taste of coffee the cleaning procedure as described above should be repeated periodically and at least once per month or as necessary according the grinder s usage and quality of beans END 14 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 Add your remarks here vate evem e P wms O Important details and telephone numbers Local dealer Address Telephone number Fax number Technician mobile number name Coffee beans supplier details Telephone number Fax number 15 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012
3. Brush empty the grinding tunnel from powder using the provided brush e Pull the outlet chute out and use wet sponge and soap to clean the coffee oils and the powder s residue Fig 10 1 Remark Outlet Chute internal surface its Teflon coated use only soft sponge and liquid soap to clean it avoid scratching it e In order to ensure perfect attachment of the outlet chute make sure to clean any powder s leftovers from the outlet chute housing it is magnet slots and bottom holder Fig 10 3 Fig 10 1 Fig 10 2 Fig 10 3 12 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 Cleaning the grinding chamber grinding parts and powder outlet housing Follow the instruction below for grinding chamber and grinding parts cleaning STEP1 By using a screw driver take out the dial s safety screw Rotate the grinding dial clock wise to take it off STEP 2 Pull out the upper blade holder make sure not to lose the upper blade three Supporting springs STEP 3 Use a brush a dry cloth and a vacuum cleaner to clean the grinding chamber thoroughly STEP 4 Use a brush a dry cloth anda vacuum cleaner to clean the upper and lower blade thoroughly 13 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 e Do not use sharp objects to scrape coffee residue off of the blades or the internal Teflon coating of the outlet port e Examine both of the blades condition and replace them if necessary
4. Version 2 1 September 2012 7 SAFETY DEVICES A Thermal overload protection In order to eliminate the risk of fire the motor is equipped with an overheat protection device which will cutoff the motor s power supply should it reach a high temperature In the event that the thermal protection is tripped as a result of malfunction e g jammed blades worn out bearings foreign object in grinding chamber etc the appliance main switch should be turned off immediately and the main power plug must be disconnected For further handling of the device contact your local service provider and allow the appliance to cool down before any further maintenance In the event that the thermal protection is tripped as a result of a long continuous operation read section 5 for operating intervals allow the appliance to cool down and reset the thermal cutoff protection by unplugging the main cable from the socket On the first operation after resetting a tripped overheat protection device observe the grinding quality and noise level and if there are any irregularities shut down the appliance and call a certified technician for a complete analysis of the appliance B Grinding chamber safety screws The grinding chamber can be a hazardous area if the proper precautions aren t observed The hopper safety screw fig4 1 and the grinding dial safety screw fig6 1 should never be removed during normal operation of the appliance unless the appliance is disco
5. with the legislation of the customer s own country of residence with a minimum of 1 year Germany 2 years starting from the date on which the appliance is sold to the end user The warranty only covers defects in material or workmanship The repairs under warranty may only be carried out by an authorized service centre When making a claim under the warranty the original bill of purchase with purchase date must be submitted The warranty will not apply in cases of Normal wear and tear Incorrect use e g overloading of the appliance use of non approved accessories Use of force damage caused by external influences Damage caused by nonobservance of the user manual e g connection to a nun suitable mains supply or non compliance with the installation instructions Partially or completely dismantled appliances ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 TABLE of CONTENTS MEP PS TACO atest seande testes sapsnemntcsee A A ES 2 Techmeal SPC CITICATIONS snina E T 3 General DeScriDHUON aoan T AA A Unpackng and instalatia senene E 5 Operation VL models eriraiannaen A 6 Operation V3 MOCEIS ssurpise e T NEA A T II ACCESS Orie Sna eA a casino aged aes 8 Salet VOV CE Sarera R a deddsdeessthoadtiaendens I SATELY nS UCHO Seea TaT NE G 10 Maintenance and servite neperi ana a EEEE U a e E EE AE E eras nce A V E E 10 Remarks and important Aetails ccccscccscssseecsseseseceeeseeesecsesescseeessaes E
6. HC 600 Model ODG V1 V3 ON DEMAND COFFEE GRINDER Designed in EU Produced in China by Elan Changzhou Hardware Co Ltd Building 6 2 Tenglong Rd Wujin Economic Development Zone Jiangsu 213161 China ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 WARNINGS 1 This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety 2 Children should be supervised to ensure that they do not play with the appliance 3 Care is needed when handling cutting blades during cleaning 4 If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling Warranty Information The manufacturer provides warranty in accordance
7. LAN Changzhou Hardware Co Ltd Version 2 1 September 2012 10 poe ba le LS MH be a16 1 PREFACE Congratulations for purchasing the HC 600 On Demand Grinder ODG The HC 600 is a commercial appliance to be used in coffee shops espresso bars hotels restaurants and so on HC 600 will grind whole been coffee into variable user selectable from super fine to course coffee powder and will dose a pre defined on V1 models dose to your espresso machine filter holder Read this manual from cover to cover before using the appliance as it contains important instructions for the safety operation and maintenance of the appliance Keep the manual ina reachable place for future use and reference The manufacturer reserves the right to modify from time to time the appliance and the manual accordingly 2 TECHNICAL SPECIFICATIONS HC 600 Dimensions Height 560mm Width 210mm Length 330mm Weight 15Kg Burrs diameter 64mm Hopper capacity 1200gr Coffee beans Electrical Specifications 230V 50Hz or 110V 60z or 220V 60Hz as marked Power 350w Duty Cycle 50 Grinding capacities 6 9Kg hour 3 General Description Model V1 Bean hopper door Bean hopper lid Powder outlet lid Bean hopper Powder outlet p Hopper Safety screw Espresso filter handle support B Grinding dial Program dial V1 Grinder body LCD display and counter mode selector V1 Residue tray Working mode selector V1
8. alled with a simple operating main switch consisting of 2 running modes fig 5 1 A e Continues mode while selecting the ON position the grinder will run and grind coffee continuously up until the user will switch main switch back to Off position e Dosing mode while selecting the Auto position the grinder will run together with the demand switch and as long as it pressed Grinding in continues mode The HC 600 ODG is designed to grind continuously into bags or any other collecting tool Nevertheless this machine was not designed as a pure bags grinder We suggest In continues mode do not grind more than 10kg 20 pounds of coffee per day Grind in intervals of not more than 1 kg 2 pounds per hour When grinding in continues mode Keep the powder outlet top cover open and shake the bag from time to time View the free flow of coffee to avoid back logging of the powder into the grinding chamber In that case stop the grinding use the provided brush to evacuate the clogged powder into the bag and resume grinding V3 ONLY Operating intervals e tis anormal occurrence that during long grinding periods the grinding chamber will heat up In order to achieve best grinding results it is recommended to grind coffee in short intervals of a few minutes each Adjusting coffee grind e The grinding blades distance was factory pre adjusted to satisfy different common coffee grinds from super fine to coarse corresponding gap distan
9. ce from 0 05mm to 0 5mm e Turning the grinding dial incrementally counterclockwise will make the grind finer and turning it clockwise will make the grind coarser e Grind a small amount of coffee and test its coarseness with your espresso machine e As coffee beans qualities and characteristics are changing from time to time it is recommended repeating this adjustment once in a while Safety screw ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 6 Accessories 1 Porte filter holder accessory for models sold after August 2009 Fig 1 1 Fig 1 2 1 Notice the two holes under the filter fork support fig 1 1 2 Unpack the accessory fig 1 2 which is packed separately within the grinder packaging 3 Insert the accessory into the 2 holes fig 1 3 Fig 1 3 Fig 1 4 4 Place your filter supported by the fingers and the back accessory fig 1 4 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 2 Outlet powder restrictor on models earlier than 2012 Fig 1 1 EF 1 In some cases for specific Porte filters height you may require to restrict the flow of the outlet powder to avoid unnecessary waste 2 Unpack the accessory fig 1 2 which is packed separately within the grinder packaging 3 Use the accessory s 2 ears in order to half turn and assemble it onto the 2 pins on the powder outlet port fig 1 3 i i ul 10 ELAN Changzhou Hardware Co Ltd
10. g blades periodically approximately every 50kg of grinded coffee Good condition blades will result in a high quality grind and prevent the appliances over heating Replace grinding blades every 400KG of grinded coffee when using original replacement parts Be aware of the appliance s noise level In case the noise level is higher than normal or irregular noises are coming from within the appliance get certified personnel to perform an overall check of the appliance 10 CLEANING BEFORE ANY CLEANING ROUTINE DISCONNECT THE APPLIANCE POWER SUPPLY NEVER USE RUNNING WATER TO CLEAN THE MAIN BODY AND POWDER OUTLET USE ONLY PERFECTLY CLEAN CLOTHS OR BRUSHES TO CLEAN THE APPLIANCE DO NOT USE ABRASIVE CLEANING PRODUCTS AS THEY MAY WEAR OUT THE APPLIANCE COATING Cleaning the beans hopper Take off the bean hopper by releasing Bean Hopper safety screw Fig 4 1 and rinse it thoroughly with water and soap As the bean hopper is made of clear polymer use only liquid detergent free of abrasive components and soft sponge Before reinstalling the beans hopper back to its position make sure it is dried thoroughly To ensure great coffee taste clean the bean hopper periodically Cleaning the Outlet powder chute from 2012 models and on The Grinder is provided with magnet detachable powder outlet In order to clean the outlet chute follow the next steps e Disconnect the grinder from the power source to avoid undesired operation Safety requirement e
11. modes is achieved by single pressing on the relative mode selector button Once activated a green LED will turn to ON state on each one of the selectors e Continues mode while in continues mode pressing longer than 3 sec on continues mode button will start the grinder The relative LED will blink as long as the grinder is running stopping the grinder by another short press on continues mode button e Single cup mode while in single cup mode any press on the demand switch fig 5 2 will activate the grinder to grind a precisely timed dose time can be programmed by user into the filter handle e Double cup mode while in double cup mode any press on the demand switch fig 5 2 will activate the grinder to grind a precisely timed dose time can be programmed by user into the filter handle Remark Stopping an undesired grinding operation before reaching complete dose by pressing continues mode button Demand switch ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 Dose counting LCD e The HC 600 ODG model is equipped with 3 independent dosing counters e In order to view each one of the counters a single press on the counter selector will flip the LCD to the next counter and the relative counter s LED will turn on e 2 ofthe counters are resettable middle and left most LED in order to reset each of these 2 counters a 5 sec continues press on the counter selector will zero the relative counter e On single cup m
12. nnected from the power source 8 SAFETY INSTRUCTIONS NEVER OPERATE THE GRINDER IF THE BEAN HOPPER IS NOT FULLY SECURED TO THE TOP BLADE HOLDER BEFORE REMOVING THE HOPPER FOR ANY REASON MAKE SURE TO DISCONNECT THE POWER SUPPLY AVOID CLEARING FOREIGN OBJECTS FROM THEGRINDING CHAMBER OR HOPPER WHEN THE APPLIANCE IS PLUGGED INTO A POWER SOCKET Never attempt to insert your fingers or any foreign objects into the grinding chamber or blades Be aware that grinding blades continue rotating for a short while after the grinding operation has ended BEFORE ANY MAINTENANCE EVEN FOR CLEANING ALWAYS DISCONNECT THE POWER SUPPLY In the event that the appliance has a malfunction or the blades need to be replaced do not attempt to service the appliance unless you got the specific training by a certified trainer to do so Do not change or tamper with the appliance Do not use the appliance barefoot or if your hands or feet are damp Do not use the cable wire to pull and disconnect the power plug Always keep the appliance dry internally and externally Never re grinds grinded coffee Never attempt grinding anything else other than coffee beans 11 ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 9 MAINTENANCE AND SERVICE Warning All appliances technical handling operations such as installation maintenance or service should be performed by certified personnel or by your local dealer Check the state of the grindin
13. ode each coffee demand will increase the counting on all the 3 counters in 1 e On double cup mode each coffee demand will increase the counting on all 3 counters in 2 e On continues mode the counters are not counting Programming grinding time for single and double cup mode The HC 600 ODG is factory set with time values for single and double dose grinding periods These pre set values are obviously estimated and user should find his own times according the coffee grinding request In general as the coarseness of grind is coarser the time required to grind same weight of coffee is shorter Additionally different type of coffee blends and coffee shops are requiring different dose size for their single and double cups 6 5gr to 9 5gr per single cup and 11gr to 18gr for double cup The HC 600 ODG is supporting the need of the user to change grinding time setting frequently In order to change time setting of single cup or double cup mode please follow these steps 1 Press the desired mode selector button continuously for longer than 3 sec when in programming mode the mode selector s LED is blinking 2 Watch the LCD display is now showing your current set up time in seconds and tents of seconds 3 In order to increase or decrease set up time simply rotate the peripheral scale of the knob and watch the time set up on the LCD is changing up or down according direction of rotation 4 When reaching the desired time value press shortly the mode selector but
14. the supply mains if the ground system was not positively checked to be in compliance with current safety rules IT IS COMPULSORY TO GROUND THE APPLIANCE The manufacturer can not be held responsible in the event that this regulation is not complied with o The power consumption of the appliance according to the backside label is consistent with the relevant wall socket capacity o The wall socket is protected against short outs and power surges o Do not use extension cables plug adapters for multiple sockets or make shift connections Plug in the appliance Upon first time operation and before placing beans into the hopper VISUALLY check that the blade rotation direction is clockwise by switching the appliance ON for a short while Should the rotation direction be wrong do not use the appliance and contact your local dealer for further instructions ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 5 OPERATION for V1 models only for V3 models jump forward to page 8 Grinding coffee with HC 600 On Demand Grinder Continues mode selector SEE N LCD display Single cup mode selector Double cup mode selector f Counter selector button Programming dial Fig 5 1 Before start grinding coffee please spend some few minutes to learn and understand the concept of the HC 600 ODG controller fig 5 1 Modes of operation The HC 600 ODG can be operated in 3 different modes Activating or deactivating each one of the
15. ton to return to normal working mode watch the display is returning to counter mode Grinding in continues mode The HC 600 ODG is designed to grind continuously into bags or any other collecting tool Nevertheless this machine was not designed as a pure bags grinder We suggest In continues mode do not grind more than 10kg 20 pounds of coffee per day Grind in intervals of not more than 1 kg 2 pounds per hour When grinding in continues mode Keep the powder outlet top cover open and shake the bag from time to time View the free flow of coffee to avoid back logging of the powder into the grinding chamber In that case stop the grinding use the provided brush to evacuate the clogged powder into the bag and resume grinding 1 Select continues mode button continues mode LED is turned on 2 If you wish to grind into a collecting tool or bag unscrew the fork legs fig 5 3 and place the collecting tool under the outlet port fig 5 4 To start grinding press the continues mode button for longer than 3 sec 3 The grinder will turn on and the LED will start blinking Stop the grinding by another short press on continues mode button ELAN Changzhou Hardware Co Ltd Version 2 1 September 2012 V3 ONLY 5 OPERATION for V3 models only Grinding coffee with HC 600 On Demand Grinder Automatic mode Continues mode selector Power indicator Fig5 1A Modes of operation The HC 600 ODG V3 grinder is inst
Download Pdf Manuals
Related Search