2075DWRWC — Drawer Model Wine Captain ® Installation - U-Line
Contents
1. Note The slides have extra mounting holes that may be used Mark and Drill New Mounting Holes 1 Remove one slide s mounting screws odo obo 2 Reposition the slide so it is the same distance from the bottom of the liner as the other slide Measure to confirm Upward or Push Slide Downward Figure 16 3 Mark new drilling holes using different sets of mounting holes on the slide See Figure 16 Note Front location holes are shown Corresponding rear holes will also need to be marked 4 Drill all the new holes with a 30 drill bit 5 Remount the slide Re installation of Drawer CAUTION Use care when handling the drawer Drawer edges drawer rail and the unit s slide may be sharp 1 Set the drawer s rails onto the slides 2 Re install the rails mounting screws See Figure 7 on Page 8 3 Plug in the drawer s connection wiring top drawer only 4 Go on to 6 Prepare Power Supply 02 2005 2075DWRWC Drawer Model Wine Captain UJ U LINE 6 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician The unit requires a grounded and polarized 115 VAC 60 Hz 15A power supply normal household current An individual properly gr2. height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening www U LineService com UFsLINE NE 2075DWRWC Drawer Model Wine Captain ecCORPORATION e Install the Unit Horizontal Mounting Left Side Shown Installation of the 2075DWRWC 1 Plug in the power cord N Countertop or Wall Header 2 Gently push the unit into position Be careful not to entangle the electrical cord 3 Re check the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop Anti Tip Kit Installation N WARNING lo The Anti Tip Kit must be installed on this unit before it is used Vertical Mounting e Additional blocking or special fasteners may be Left Side Shown required for installation Installer is responsible Cabinet or Wall Stud for secure attachment to prevent the unit from tipping Make sure the mounting screws attaching the unit to the counter cabinet or wall are deep enough into the mounting surface to support the weight of the drawers and the items that will be inside the drawers Never use the drawers as steps or as a shelf to
3. mounting screws 1 Loosen the slide s mounting screws 2 Push the slide backward 2 Level the slide 3 Retighten the screws 3 Retighten the screws See Figure 12 See Figure 9 4 Repeat procedure for the other slide Figure 12 Figure 9 Severe Adjustment Severe Adjustment Note The slides have extra mounting holes that Mark and Drill New Note The slides have may be used Mounting Holes extra mounting holes that Mark and Drill New may be used Mounting Holes 1 Loosen one slide s rear mounting screws 1 Remove the slide s g mounting screws ao OCH 2 Remove the slide s front mounting screws 2 Reposition the slide so it is the same distance E 3 Reposition the slide so evel the Slide from the front of the Sg it is level liner as the other slide Se e i Backward A Mark new front drilling Figure 13 Measure To caniin Figure 10 holes using a different set of mounting holes on the slide See Figure 13 5 Drill the new holes with a 30 drill bit 3 Mark new drilling holes using different sets of mounting holes on the slide See Figure 10 Note Front location holes are shown Corresponding rear 6 R mo unt the slide holes will also need to be marked 7 Repeat procedure for the other slide 4 Drill all the new holes with a 30 drill bit 5 Remount the slide Front to Back Adjustment See F
4. J UsLINE CORPORATION 7 Lightly sand tack and reapply 2 times if desired 8 Allow the final coat to dry for 24 hours 9 Reinstall wood trim to wine racks and caddy using screws removed in Steps 2 and 3 10 Reinstall the removed wine racks and caddy in unit 11 Go on to 5 Adjust Drawers Staining Wood Trim a Different Color IMPORTANT Do not remove the two racks attached at the drawer slides 1 Remove wine caddy the top two racks in the upper drawer and the top rack in the bottom drawer remove each wine rack by sliding it out and up See Figure 5 2 Remove and save screws securing wood trim to the racks and caddy 3 Remove and save screws securing wood trim to the two racks attached at the drawer slides without removing these racks themselves 4 Apply Minwax Water Based Wood Stain to wood with a synthetic foam brush Stain must penetrate approximately 3 minutes After this period while stain is still wet take a stain dampened rag and remove all excess stain Wipe in the direction of the grain with medium pressure to achieve the desired stain color 5 After 2 hours repeat Step 4 6 Allow stain to dry for a minimum of 3 hours before finishing 7 Sand the wood with very fine sandpaper to smooth the surface from the staining process 8 Remove sanding dust with a tack cloth 9 Apply a thin coat of Minwax Polycrylic following container label for directions Allow to dry 24 hours 10 L
5. UFLINE C OR PORATION Echelon Series Installation Guide EEE 2075DWRWC Drawer Model Wine Captain www U LineService com Phone 414 354 0300 e FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 e FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 U LINE NE 2075DWRWC Drawer Model Wine Captain ecCORPORATION Contents Exterior Cleaning 4 Cut Out Dimensions 4 Product Dimensions 5 Clearances Information 5 Other Site Requirements 6 Adding a Final Finish Coat to Wood Trim 7 Staining Wood Trim a Different Color 7 Checking Drawer Alignment 8 Adjusting Drawer Alignment 8 Electrical Specifications 11 Leveling Information 11 Installation ip 11 Installation of the 2075DWRWC 12 Anti Tip Kit Installation 12 Installation Troubleshooting 13 Initial Start Up 13 Start Up Troubleshooting 14 Service Information 15 www U LineService com 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to ins
6. age appliances Echelon SERIES Origins SERIES U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter icemakers Combo icemaker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2005 U Line Corporation Publication No 30059E 02 2005 Rev A
7. ay be coated with a final finish or stained If neither of these treatments are to be included in this installation go on to 5 Adjust Drawers AE CAUTION To prevent permanent damage to the inner liner of the Wine Captain the wine rack wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the stain finish manufacturer s instructions prior to re installing the wood trim inside the cabinet of the Wine Captain Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty Adding a Final Finish Coat to Wood Trim IMPORTANT Do not remove the two racks attached at the drawer slides 1 Remove wine caddy the top two racks in the upper drawer and the top rack Slide Out in the bottom drawer and Up remove each wine rack by sliding it out and up See Figure 5 2 Remove and save screws securing wood trim to the racks and caddy 3 Remove and save screws securing wood trim to the two racks attached at the drawer slides without removing these racks themselves Figure 5 4 Lightly scruff sand the wood trim with 280 grit 3M Tri M Ite sandpaper 5 Remove sanding dust with a tack cloth 6 Apply a thin coat of Minwax Polycrylic following container label for directions Allow to dry 24 hours 02 2005 2075DWRWC Drawer Mlodel Wine Captain U
8. djustment and re installation 1 Confirm that the unit is unplugged from wall outlet 2 Unplug the drawer s connection wiring top drawer only 3 Remove the mounting screws See Figure 7 4 Pull the drawer completely out of the unit Mountin Screw Figure 7 CAUTION Use care when handling the drawer Drawer edges drawer rail and the unit s slide may be sharp IMPORTANT Drawer adjustments are made by moving the slide that carries the drawer s rail Minor adjustments may be made by loosening one of the slide s mounting screws adjusting the slide and retightening the screw Severe adjustments may be made by removing the slides mounting screws drilling new mounting holes and remounting the slide Side to Side Adjustment See Figure 8 The drawer will need a Side to Side Adjustment if when viewed from the top the drawer front is not square with the sides of the cabinet This is caused by one of the slides being mounted too far forward on the unit s liner Not Aligned Side to Side T A Top View of Unit Figure 8 02 2005 2075DWRWC Drawer Model Wine Captain UJ U LINE CORPORATION Minor Adjustment Minor Adjustment Note The mounting holes Note The mounting holes on the slide are slightly Loosen on the slide are slightly larger than the screws Mounting Screws i larger than the screws ER diameter diameter 1 Loosen one slide s
9. ed to chlorine gas pool chemicals salt water or cleaners with bleach e Clean glass drawer fronts with a non chlorine glass cleaner Keep your stainless steel surfaces looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis Do not clean with steel wool pads Do not use stainless steel cleaners polishes on the glass surfaces Do not use cleaners that are not specifically intended for stainless steel on stainless steel surfaces this includes glass tile and counter cleaners e If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible www U LineService com 3 Prepare Site You
10. ightly sand tack and reapply 2 times if desired 11 Allow the final coat to dry for 24 hours 12 Reinstall wood trim to wine racks and caddy using screws removed in Steps 2 and 3 13 Reinstall the removed wine racks and caddy in unit 14 Go on to 5 Adjust Drawers www U LineService com UFLINE 2075DWRWC Drawer Model Wine Captain CORPORATION 5 Adjust Drawers Checking Drawer Alignment The unit s drawers are aligned at the factory before shipment However their alignment could have been disturbed during shipment Aligned Front to Back gt E Aligned Side to Side Aligned Top to Bottom Figure 6 See Figure 6 Check each drawer to confirm that it is aligned Side to Side When viewed from the top the drawer front should be square with the sides of the cabinet Front to Back When viewed from the side the drawer front should be straight with the cabinet s sides not cocked forward or back Top to Bottom When viewed from the front the drawer should be level horizontally If both drawers are properly aligned go on to 6 Prepare Power Supply If either drawer is not aligned carefully follow instructions to remove that drawer make the necessary adjustment and re install the drawer www U LineService com Adjusting Drawer Alignment A WARNING SHOCK HAZARD The unit must be unplugged from the wall outlet during drawer removal a
11. igure 11 The drawer will need a Front to Back lt Not Aligned Front to Back Adjustment if when F viewed from the side the drawer front is cocked forward or back This is caused by the front slide mountings not being level with the rear slide mountings Side View of Unit Figure 11 02 2005 9 www U LineService com UFLINE 2075DWRWC Drawer Model Wine Captain CORPORATION Top to Bottom and Left to Right Adjustment ot Aligned Top to Bottom Not Aligned Left to Right o Front View of Unit Figure 14 Top View of Unit See Figure 14 The drawer will need a Top to Bottom Adjustment if when viewed from the front the drawer is not level horizontally Viewed from the top one side will protrude This is caused by one of the slides being mounted higher than the other slide on the unit s liner Minor Adjustment Note The mounting holes on the slide are slightly larger than the screws diameter Loosen Mounting Screws 1 Loosen one slide s mounting screws 2 Push the slide upward or downward to match the position of the other slide Push Slide Q Upward or Downward 4 3 Retighten the screws See Figure 15 4 Repeat the procedure with the other slide if necessary Figure 15 www U LineService com Severe Adjustment
12. oint displays Wait 10 seconds for the new set point to be saved Wait 24 hours for the temperature to stabilize before checking the actual temperature again Each wine compartment can be set to 40 F to 60 F Note A flashing indicator light LED dot indicates a thermistor error in that drawer Call for service Other Settings Other settings for the unit are factory preset No adjustments should be necessary at this time See the User Manual for information on e Adjusting the interior lighting e Removing the lower drawer s wine caddy e Using or disabling the cascade feature www U LineService com 14 Start Up Troubleshooting Q Problem Unit does not appear to turn on when plugged in P Solution Make sure outlet has power circuit breaker has not tripped IMPORTANT See the User Manual s Troubleshooting Guide for more solutions 02 2005 UJ UFLINE CORPORATION Who to Call Service Information If the need for service arises contact the dealer from whom the unit was purchased State the Model Number and Serial Number and explain the problem The Model and Serial Number plate is located inside unit at upper right hand corner If you need to locate a service company you can go online at www U LineService com and search for a service company by zip code For more than four decades U Line has distinguished itself as the leader in built in undercounter ice making refrigeration and wine stor
13. ounded branch circuit or circuit breaker is recommended GFCI ground fault circuit interrupter is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See Figure 17 for recommended receptacle location 23 11 16 Figure 17 N WARNING SHOCK HAZARD Electrical Grounding Required Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit Go on to 7 Level the Unit 02 2005 CORPORATION 7 Level the Unit Leveling Information Note It is recommended that the unit is level 1 Use a level to check the levelness of the unit from front to back and from side to side Level should be placed along top edge and side edge as shown see Figure 18 Figure 18 2 If the unit is not level adjust the feet on the corners of the unit as necessary see Figure 19 Turn Foot to Adjust Figure 19 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Go on to 8 Install the Unit Installation Tip If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a total unit rear
14. r U Line product has been designed for built in installation Your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for electrical connection in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions F e See Electrical Specifications for Power Supply N ht Figure 1 23 11 16 Follow the cut out drawing in Figure 1 The 24 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations The unit is 23 11 16 deep including the drawer and not the full handle see Figure 2 02 2005 2075DWRWC Drawer Model Wine Captain UJ U LITNE Product Dimensions P95 43 16 Including Handle Bag Black or Stainless Steel Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 19 on Page 11 02 2005 CORPORATION Clearances Information The unit must be installed in a wall or under a counter top to allow for the installation of the Anti Tip Kit see Page 12 N WARNING The Anti Tip Kit must be installed on this unit before it is used Never use the drawers as steps or as a Shelf to support more than the drawers contents Serious pe
15. rsonal injury could occur The unit is designed so it can be installed next to a wall on either side see Figure 3 x Cabinet or Wall Figure 3 www U LineService com UFLINE NE 2075DWRWC Drawer Model Wine Captain ecORPORATION The drawer unit can be installed with an appliance or Other Site Requirements fixture located in front of it as long as there is adequate clearance for the drawer to be opened and removed Power Supply when servicing see Figure 4 I f _ The unit requires a grounded and polarized 115 VAC Note U Line recommends you consider additional 60 Hz 15A circuit normal household current See clearance in front of the open drawer for convenience Electrical Specifications on Page 11 Environmental Requirements The surrounding air temperature must be at least 50 F 10 C but must not exceed 110 F 40 C Units may be installed outdoors in a covered area The unit must not be located near heat generating equipment or in direct sunlight Figure 4 www U LineService com 6 02 2005 4 Prepare Racks and Caddy The U Line Wine Captain is equipped with wood trimmed wine racks that are coated at the factory with a clear vinyl sealer which will adequately protect the wood in normal usage A final finish coat was not applied so that the wood trim could be stained to match d cor The trim on the racks m
16. s open approximately 8 If it is not re check leveling from front to back of the unit and readjust if necessary 02 2005 9 Start Up for the First Time Initial Start Up Once installation and leveling is complete the unit is ready for initial start up and operation Temperature Controller Figure 21 The temperature controls are integrated in the top front drawer panel They consist of an LED display and touch sensors for each drawer and a touch sensor to control the lighting C AA N and The LED displays show the drawer s temperature set point and are calibrated in degrees Fahrenheit The controls are factory programmed for a set point of 60 F for the top drawer and 40 F for the bottom drawer Each drawer s display will show its set point when the unit is first powered up Figure 22 www U LineService com UFLINE NE 2075DWRWC Drawer Model Wine Captain ecORPORATION To display actual temperature of each drawer press the A and V touch sensors simultaneously for three seconds The display indicates the actual temperature After approximately 10 seconds the set point temperature displays To adjust the temperature set point touch and hold either the AA or WM for that drawer for three seconds When the LED displays SP lift your finger from the controller and the corresponding LED will begin to flash the set point Touch the AA or V until the desired set p
17. support more than the drawers content Serious personal injury could occur After leveling the unit must be secured to a counter a cabinet or a wall to prevent tipping 1 Open the upper drawer to expose the six screws A installed at the top two corners three at each corner Remove the appropriate screws for horizontal or vertical mounting see Figure 20 Do not discard Figure 20 www U LineService com 12 02 2005 CORPORATION i 2075DWRWC Drawer Model Wine Captain UFLINE 2 Insert the screws through the anti tip bracket B and attach the bracket to the unit Tighten screws securely 3 Repeat for the other side Note The bracket should be flush with the surface it is being attached to If it is not loosen the screws and slide the bracket against the mounting surface Tighten screws securely 4 Using two of the screws C supplied fasten the screws through the bracket and into the counter cabinet or wall IMPORTANT Certain cabinets or countertops may require special fasteners or additional wood blocking to anchor properly CAUTION Make sure the screws are back far enough so they do not damage any exposed front surface of the cabinet Installation Troubleshooting Q Problem The drawer remains open unless it is pushed closed A Solution The drawer should be self closing when it i
18. tain and synthetic foam brush Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating Stainless Steel Models When inspecting installing a Stainless Steel unit the protective coating covering the drawer fronts must be removed Start at a corner of the drawers and pull back the protective coating to remove it from the drawer fronts After all the protective coating has been removed from the drawers clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration Clean all glass surfaces with a non chlorine glass cleaner www U LineService com U LINE NE 2075DWRWC Drawer Model Wine Captain ecORPORATION Exterior Cleaning As Required Black Models e Clean glass drawer fronts with glass cleaner The drawers grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models can discolor when expos
19. tall or operate the unit This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death N WARNING Warning means that failure to follow this safety statement could result in serious personal injury or death NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 02 2005 2075DWRWC Drawer Model Wine Captain UJ UFLINE General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide N WARNING SHOCK HAZARD Electrical Grounding Required Keep the unit unplugged throughout installation except during testing Never remove the round grounding prong from the plug and never use a two prong grounding adapter Never use an extension cord to connect power to the unit Always keep your working area dry A WARNING The Anti Tip Kit must be installed on this unit before it is used Never use the drawers as steps or as a Shelf to support more
20. than the drawers contents Serious personal injury could occur CAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the drawer handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 CORPORATION 2 linspect and Plan You have received a carton containing your 2075DWRWC Drawer Model Wine Captain with a package inside containing a User Manual a Product Registration Card and Anti Tip Kit Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference Your unit is Black or Stainless Steel Black units have drawers with black glass fronts sculpted handles and black vinyl clad cabinets Stainless Steel units have drawers with stainless steel framed fronts sculpted stainless steel handles and black vinyl clad cabinets All units come with maple trim wine racks and caddy that can be finished or stained Please carefully follow the directions that apply to your unit and your intended design Tools Materials Required e Wrenches e Screwdrivers slotted and Phillips head e Sandpaper low odor water clean up quick drying finish tack cloth and if desired water based wood s
Download Pdf Manuals
Related Search