Profoto B1 500 AirTTL
Contents
1. Dongle for using Profoto Air Software WW pr ofoto com Ir ii Profoto B1 50 Profoto B1 500 Air TTL Slave Sync operation When Slave is shown in the Sync Air setting section 21 on the Display 13 the B1 unit senses the flash release as well as IR signals from most IR sync transmitters 1 Ifthe Sync Air setting section 21 is blank press the SYNC button 18 once to activate wireless sync AIR or Slave is now displayed 2 Ensure that Slave is displayed If not press and hold the SYNC button 18 until Slave is displayed Cable Sync operation Sync via cable is possible in all sync modes Connecta sync cable from the camera or flash meter to the Sync Connector 11 onthe B1 unit Modeling light settings The current setting is shown in the Modeling light setting section 19 on the Display 13 1 Press the MODEL button 14 to turn the modeling light on or off 2 With the modeling light on press and hold down the MODEL button 14 to toggle between PROP and FREE e PROP The modeling light intensity is automatically adjusted to be proportional to the selected energy level of the flash light e FREE The modeling light intensity is manually set independent from the energy level of the flash light 3 If FREE is selected With the modeling light on press and hold down the MODEL button 14 until the percentage value is blinking Turn the ENERGY SETTINGS dial 16 to2. 0 full power flashes Battery life 300 charge cycles to 80 capacity left Battery status indicator Approx battery level in percentage of the total capacity is indicated on the Display 3 sections 100 70 2 sections 70 40 1 section 40 10 1 section blinking lt 10 Battery charging time 2h 1h with Battery Charger 4 5A Auto power off Yes after 60 minutes Sleep activated after 30 minutes 18 Battery operating temperature 10 C to 50 C 4 F to 120 F range attery storage temperature 20 C to 60 C 20 F to 140 F range Wireless sync Yes via all Air camera transmitters or IR Slave All figures are to be considered as nominal and Profoto reserves the right make changes without further notice TLL 4IV 00S Lg 0 0 01d www profoto com Technical data and product information are subject to change without notice Profoto AB SWEDEN Phone 46 8 447 53 00 info profoto com www profoto com eo C5Profoto Profoto Air The Light Shaping Company
3. Changing flash tube and Model Light LED www profoto com Profoto B1 500 Air TTL Nomenclature O A WwW N Handle Tilt lock knob Stand adapter Clamp screw Reflector and Front glass 6 Zoomscale 7 Umbrella holder 8 Battery 9 Battery release button 10 USB port 11 Sync connector 13 LCD display 14 MODEL button 15 TEST button 12 IR Slave eye Profoto FREEZE BE 2L im 16 ENERGY SETTINGS dial 17 READY button 18 SYNC button READY SYNC PROP Lift DIM SLAVE Ci FREE 71 01 BEEP AIR ZI Ci 19 Modeling light setting 24 Freeze mode indicator 20 Ready signal setting 25 Temperature limit indicator 21 Sync Air setting 26 Automatic flash exposure TTL indicator 22 Battery level indicator 23 Light output setting Battery charger 2 8A 2 Battery charger 28 Case Bag XS Operation Quick guide For detailed operating instructions see subsequent sections Charge the battery see page 14 Mount the battery see page 14 Remove the transport cap from the Reflector Front glass 5 Fitthe Stand adapter 3 to a light stand and secure it with the Clamp screw 4 see page 14 Adjust the tilt position of the flash by loosening the Tilt lock knob 2 see page 14 Switch on the unit by pressing and holding the TEST button 15 see page 10 7 Select Freeze Normal mode by pressing and holding the ENERGY SETTINGS dial 16 and then
4. Profoto B1 500 AirTTL y_N O Profoto Profoto Air The Light Shaping Company TLL 4IV 00S 18 0 0 01d www profoto com Congratulations on your new Profoto product Regardless if you chose anew flash or anew light shaping tool know that almost half a century s worth of experience was put into its making If the years have taught us one thing it is to never neglect a single detail We only put our name on a product in which we have the fullest confidence Before shipping every one of our products pass an extensive and strict testing program Unless it complies with the specified performance quality and safety itis a no go As a result we are confident that your new Profoto product will stay with you for years and help you grow as a photographer But getting the product is only the beginning of that journey Using it for light shaping is the real adventure That is why we take pride in providing you with such a wide assortment of light shaping tools allowing you to shape the light in any way you can imagine The almostinfinite possibilities might seem bewildering atfirst but we re certain you will soon get the hang of it Still I encourage you to sign up for our newsletter at www profoto com newsletter or visit our blog at www profoto com blog so that we can share our experience from almost 50 years of light shaping and hopefully inspire you to grow even further Enjoy your Profoto product Conny Dufgran foun
5. The Profoto Car Charger 1 8A should not be used in this case Dismountthe battery Connect the battery charger to the battery pack Check that the battery charger indicates that charging is in progress When the battery charger indicates thatthe charging is completed itis recommended to disconnect the battery charger and remove the battery from the charger Stand mounting 1 Fitthe Stand adapter 3 to alight stand and secure it with the Clamp screw 4 2 The B1 unit can be directed upwards downwards when the Tilt lock knob 2 is loosened Fasten the Tilt lock knob 2 when the unit is correctly directed Mounting Profoto Light Shaping Tools The B1 s built in reflector creates a wide and even light spread with a high output In addition the B1 is compatible with more than 120 light shaping tools which can be used to shape its already beautiful light into almost any light you can imagine A wo N All tools with standard reflector mount rubber collar with clasp Mostreflectors are equipped with Profoto s unique clamp mechanism which makes them easy to mount and allows you to shape the light by simply sliding the reflector back and forth along the zoom scale 6 1 Unlock the clasp on the reflector 2 Slide the reflector onto the B1 Use the zoom scale 6 to place the reflector in the desired position 3 Secure by locking the clasp on the reflector www profoto com Umbrella mounting Umbrellas are simply
6. arked with the flash symbol are hazardous when live WARNING Electrical Shock High Voltage Mains powered generators shall always be connected to a mains socket outlet with a protective earthing connection Only use Profoto extension cables Do not open or disassemble generators or lamp heads Equipment operates with high voltage Generator capacitors are electrically charged for a considerable length of time after being turned off Do not touch modeling lamps or flash tubes when mounting an umbrella metal shaft in its reflector hole Disconnect the lamp head cable between the generator and lamp head when changing the modeling lamp or flash tube The mains plug or appliance coupler is used as disconnect device The disconnect device shall remain readily operable Batteries battery pack or batteries installed shall not be exposed to excessive heat such as direct sunlight fire or the like Caution Burn Hazard Hot Parts Do not touch hot parts with bare fingers Modeling lamps flash tubes and certain metal parts emit strong heat when used Do not point modeling lamps or flash tubes too close to people All lamps may on rare occasions explode and throw out hot particles Make sure that the rated voltage for the modeling lamp corresponds with the technical data in the user guide regarding the power supply NOTICE Equipment Overheating Risk Remove transport cap from lamp head before use Do notobstruct ventilation by placing filters d
7. change the percentage value After afew seconds the display will stop blinking and the new value will be set Ready signal settings The current setting is shown in the Ready signal setting section 20 on the Display 13 e BEEP The unit beeps when it is ready to flash again after recharging e DIM The modeling light is turned off after flashing and is turned on when itis ready to flash again e DIM BEEP The modeling light is turned off after flashing The unit beeps and the modeling light is turned on when it is ready to flash again e Blank No ready signal Use the READY button 17 to select the Ready signal setting e Press the READY button 17 to turn BEEP on or off e Press and hold down the READY button 17 to turn DIM on or off www profoto com Wrong exposure alarm When a flash is released before the unit is ready there will be a long beep and the display will blink These signals indicate that the flash light does not fully correspond to the set value The B1 will always continue to flash even ifthe set light output cannot be metas the image may still be usable if the catch of the moment was perfect The sound alarm is partially deactivated when BEEP is deactivated If BEEP is deactivated the sound alarm will only go off if B1 is used in TTL operation and cannot keep up with the camera in sequence shooting Quick burst Quick burstis an automatically activated function that allows a series burst of f
8. der NNANAL OKO fi th ROY WWW proroto com N U to B15 Profo Profoto B1 500 Air TTL General safety instructions x SAFETY PRECAUTIONS Do not operate the equipment before studying the instruction manual and the accompanying safety information Make sure that Profoto Safety Instructions always accompany the equipment Profoto products are intended for professional use Generators lamp heads and accessories are intended for indoor photographic use only Do not place or use the equipment where it can be exposed to moisture extreme electromagnetic fields or in areas with flammable gases or dust Do not expose the equipment to dripping or splashing Do not place any objects filled with liquids such as vases on or near the equipment Do not expose the equipment to rapid temperature changes in humid conditions as this could lead to condensation water in the unit Do not connect this equipment to flash equipment from other brands Do not use flash heads without supplied protective glass covers or protective grids Glass covers must be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches Lamps must be changed if they are damaged or thermally deformed When placing a lamp into the holder ensure not to touch the bulb with bare hands Equipment must only be serviced modified or repaired by authorized and competent service personnel Warning The terminals m
9. e mode is selected the Freeze mode indicator 24 is shown on the Display 13 See below overview of flash duration in Freeze vs Normal mode 1 1 000 s 1 10 000 s Freeze mode Normal mode 1 20 000 s 10 90 80 7 0 60 50 40 30 2 0 Light output Set light output Energy The light output of the flash lightis shown on the Display 13 inarelative f stop scale The maximum energy 500Ws is shown as 10 Use the ENERGY SETTINGS dial 16 to change the energy level of the flash light e Turnthe ENERGY SETTINGS dial 16 to change the energy level in 1 10 f stop increments e Press and turn the ENERGY SETTINGS dial 16 to change the energy level in 1 f stop increments The TEST button 15 is illuminated when the unit is fully charged and ready to flash Press the TEST button 15 to release a test flash www profoto com Select Sync setting The current sync setting is shown in the Sync Air setting section 21 on the Display 13 Wireless sync settings e AIR The built in Profoto Air receiver is activated The B1 is set to be triggered and or controlled from any of the optional Profoto Air transceivers offered by Profoto e SLAVE The built in IR Slave eye 12 is activated The flash will slave sync if another flash is fired or an IR signal is detected Cable sync only e Blank When the Sync setting shows blank the B1 can only be synced with cable Activate deactivate the wireless sync settings by briefly pre
10. iffusing materials etc over inlets and outlets of the equipment ventilation or directly over glass covers modeling lamps or flash tubes Note about RF This equipment makes use of the radio spectrum and emits radio frequency energy Proper care should be taken when the device is integrated in systems Make sure that all specifications within this document are followed especially those concerning operating temperature and supply voltage range Make sure the device is operated according to local regulations The frequency spectrum this device is using is shared with other users Interference cannot be ruled out Final Disposal Equipment contains electrical and electronic components that could be harmful to the environment Equipment may be returned to Profoto distributors free of charge for recycling according to WEEE Follow local legal requirements for separate disposal of waste for instance WEEE directive for electrical and electronic equipment on the European market when product life has ended www profoto com Table of Contents Automatic flash exposure TTL indicator Temperature limit indicator Check Firmware Upgrade Firmware i 0 1 0 eee mv In A ee Quick guide Power on off Select Freeze Normal mode Set light output Energy Select Sync setting Modeling light settings Ready signal settings FFG EN a Battery mounting Battery charging Stand mounting Mounting Profoto Light Shaping Tools Replacing the Reflector Front glass
11. lashes to be fired atafaster pace than the B1 canrecharge without losing light output The function is only active when the light output is setto less than full The length of the burst in number of flashes depends onthe repetition rate and the set light output The lower the light output is set the longer bursts can be triggered Thanks to this feature the B1 can trigger up to 20 flashes per second on lower power output without triggering the Wrong exposure alarm Note that the accuracy of the light outputis slightly less precise when Quick burstis active www profoto com Profoto B1 500 Air TTL Profoto B1 500 Air TTL 14 Handling Battery mounting 1 To mount the battery fit the battery pack into the B1 unit and push firmly until the battery pack locks in place Make sure there is a click sound indicating that the battery pack is properly secured 2 Todismountthe battery first switch off the B1 unit Press the Battery release button 9 and pull out the battery pack Battery charging For optimal performance the battery should be fully charged prior to usage The battery can be charged from any charge level Only use the Profoto Battery Charger 2 8A Profoto Battery Charger 4 5A or Profoto Car Charger 1 8A lf the battery has not been used for a long time the Profoto Battery Charger 2 8A should preferably be used The Profoto Battery Charger 4 5A could be used but puts more wear on a deeply discharged battery
12. mounted by sliding the umbrella shaft into the Umbrella holder 7 The diameter of the umbrella shaft must be between 7 mm and 8 mm in order to fit When an umbrella is used itis not possible to mount an external reflector at the same time 1 Slide the umbrella shaft into the Umbrella holder 7 2 After afew centimeters there willbe more friction then continue to slide the umbrella shaft a few more centimeters into the Umbrella holder 7 Replacing the Front glass The Front glass 5 can be replaced with optional front glass or glass domes Domes can be used to enhance the zoom effect if using any of Profoto s Zoomable reflectors 1 Switch off the B1 and remove the battery 2 Wait five minutes to allow the unit to be fully discharged and cooled down 3 Gently remove the Frontglass 5 by pushing the springs holding the glass gently to the sides 4 Carefully fit the front glass glass dome in place Make sure that all springs holding the glass are back in position and securely holding the front glass glass dome Changing flash tube and Model Light LED For replacement of the modeling light LED or Model Light LED contact your local dealer or distributor for professional service www profoto com Air TTL 00 LO Profoto B1 Other Automatic flash exposure TTL indicator The automatic flash exposure TTL indicator 26 is lit every time the flash output is set automatically by the camera This will only hap
13. pen when the B1 is operated together with any of the optional Air Remote TTL C N in TTL mode The indicator is lit for a few seconds after receiving a TTL flash command from the remote Temperature limit indicator The temperature limit indicator 25 is litif the B1 has reached a temperature level that has activated the built in over temperature protection When this occurs the performance is limited until the temperature level is back to an acceptable level Check Firmware 1 Switch off the B1 unit 2 Press and hold the ENERGY SET TINGS dial 16 and then press and hold the TEST button 15 until the B1 switches on 3 The current firmware version is shown on the Display 13 for example A7 Upgrade Firmware We recommend that you regularly look for firmware upgrades on Profoto com Upgrade of firmware is made via the USB port 10 following the instructions provided on Profoto com You can always contact your local dealer or distributor for professional service Technical data 500Ws 1 10 or full f stops Mode control Freeze shortest flash duration or Normal color balanced mode Flash duration Normalmode 1 11 000s 2Ws 1 1 000 s 500Ws t0 5 Flash duration Freeze mode 1 19 000s 2Ws 1 1 000 s 500Ws t0 5 Light spread with built in 71 degrees reflector Guide number 2 m 100 1S0 452 10 with Magnum reflector Battery type Exchangeable Lithium lon Battery 14 8V 3 Ah U Battery capacity p to 22
14. shortly pressing the TEST button 15 See page 11 8 Setthe briefly flash light output with ENERGY SETTINGS dial 16 See page 11 9 Release atest flash by pressing the TEST button 15 See page 11 10 Select Sync setting 21 with the SYNC button 18 see page 12 11 Select Modeling light setting 19 with the MODEL button 14 see page 13 12 Select Ready signal setting 20 with the READY button 17 see page 13 13 Mount Light Shaping Tools see page 15 A w N Oo oo Power on off 1 To switch on the unit press and hold down the TEST button 15 until the Display 13 shows the settings information 2 To switch off the unit press and hold down the TEST button 15 until the Display 13 is all black The B1 unit automatically goes into sleep after 30 minutes and shuts off completely after one hour of inactivity to save battery life www profoto com Profoto B1 500 Air TTL Profoto B1 500 Air TTL Select Freeze Normal mode The B1 unit can operate in two modes to maximize the versatility in different shooting situations e Normal mode Optimized color temperature stability over the entire energy range Best option for most types of shots e Freeze mode Optimized for shortest flash duration Best option for shots where the flash is used to freeze fast action Switch between Freeze Normal mode by pressing and holding the ENERGY SETTINGS dial 16 and then shortly pressing the TEST button 15 When Freez
15. ssing the SYNC button 18 To toggle between the wireless sync options press and hold the SYNC button 18 Air and TTL operation When AIR is selected in the Sync Air setting section 21 on the Display 13 the B1 is set to be triggered and or controlled from any of the optional Profoto Air transceivers offered by Profoto The B1 supports all available Air accessories offered by Profoto including those listed in the table below 1 Activate Air by following the instructions to Select Sync Setting 2 When Air is activated press and hold down the SYNC button 18 until the channel and group setting in the Sync Air setting section 21 is blinking and then release the button 3 Press and turn the ENERGY SETTINGS dial 16 to change the channel 4 Turnthe ENERGY SETTINGS dial 16 to change the group Note There are eight different channels 1 8 that can be set and each channel has 6 groups A F All lights set to the same channel will be synced together Groups are used to remotely control individual lights or groups of lights on the same channel when a set up is made with more than one light Air Accessories compatible with B1 For operation instruction refer to user guide of respective accessory Optional ProfotoAir Usable features in combination with B1 500 AirTTL accessories Flash sync Remote control TTL Automatic flash setting mmo E S wenen ooo ooo wwe o S a E A Optional Camera mounted transmitters
Download Pdf Manuals
Related Search