V-Control Users Guide_1.2
Contents
1. Using V Control with Pro Tools Setting up V Control as a Control Surface in Pro Tools To set up V Control for use with Pro Tools perform the following steps Launch the Ney Fi application In Pro Tools select Setup MIDI Input Devices Enable the V Control and both V panner MIDI inputs by selecting their respective check boxes Select the Peripherals dialog from the Setup menu Select the MIDI Controllers tab and then set up the following three controllers o For Controller 1 select type HUI and then select V Control as both the receive from and send to choices Select 8 for the of channels field o Forcontroller 2 select type SurroundPan and then select V Pan 1 as both the receive from and send to choices Select 0 for the of channels field o Forcontroller 3 select type SurroundPan and then select V Pan 2 as both the receive from and send to choices Select 0 for the of channels field The above steps are a one time process and do not need to be repeated again Close and re open V Control on the iPad If everything is set up correctly the computer running Ney Fi will be available to choose from in the computer picker in the settings window V Control and Pro Tools should now have complete bi directional control of each other Important Windows Information for Pro Tools 9 Running as Administrator Pro Tools 9 must be run as administrator t2. Setting Up a Local Network with Wi Fi V Control uses the iPad s Wi Fi capabilities to communicate with your DAW Please make sure the DAW computer and the iPad are connected to the same local area network LAN While you can get very good performance when wirelessly connected to your host computer you can achieve the highest levels of performance when the host computer uses a hard wired Ethernet connection to your local network or if a computer to computer network is set up on the computer for a direct Wi Fi connection between the iPad and computer You may want to do this if you want V Control to perform as accurately and responsively as possible especially when performing mix moves like mutes For information on setting up a computer to computer network see Creating a computer to computer network in Mac Help For Windows look online for information about creating an ad hoc windows network Installing Ney Fi Ney Fi is a free utility that must be installed and run on your DAW computer Ney Fi creates a virtual software MIDI port for the DAW software to communicate with V Control over your network so it must be running for V Control to detect the DAW system Follow these instructions to install Ney Fi Quit the DAW software if it is currently running Download the appropriate OS X or Windows Ney Fi installer at www neyrinck com downloads Run the installer o Windows Installer Launch the Ney Fi Setup exe application
3. This window contains the following controls Surround Panner Screen This screen shows the current position of the track within the surround sound field Two surround panner screens are shown in the popup in total This allows you to Adjust the panning of both sides of a stereo track Adjust the panning of two mono tracks simultaneously Each panner window has its own set of independent controls allowing them to work as two completely separate panning modules Pan Position Screen Touch and drag a path in this display to control the surround pan position of the audio track within the surround panning field This touchscreen area emulates the hardware panner joystick on a Pro Tools surround panner Note that due to the limitations of the emulation the screen will not show any indication of the current position of the audio within the sound field Cursor Left Button Touch this button to move panner focus to the track above if the Pro Tools Edit window is active or on the left if the Pro Tools Mix window is active Cursor Right Button Touch this button to move panner focus to the track below if the Pro Tools Edit window is active or on the right if the Pro Tools Mix window is active Cursor Up Button Touch this button to step upwards through the main output and send panners on the focused track so that you can select a panner to control Cursor Down Button Touch this button to step downwards through the main outpu
4. When the popup window s Inserts button is pressed the popup window displays Inserts in the upper left hand corner and the window works as follows FX Rotate this control to select which of the 8 channel insert slots to adjust The display above the rotary control will show which insert slot is currently being adjusted On Off Rotate this control to toggle the bypass state on off for the currently selected insert slot The control reads on when the insert is active and off when the insert is bypassed Selected Effect Rotate the third control in the window to scroll through all available stock and third party insert effects available to Cubase Nuendo The display above the rotary control will show which insert effect is currently selected Parameter Adjustment Swipe the top of the popup window to navigate to additional pages where the parameters of the selected insert can be adjusted 4 at a time The number of pages available to swipe to will depend on the particular effect that is selected An insert effect with a large number of parameters will have more pages of parameters to adjust Toggle Button When adjusting inserts with the popup window the toggle button has no effect Known Issues with V Control 1 2 and Cubase Nuendo The pan controls are not updated by Cubase when it is reset in the HUI Setup if already set to pan mode To better reset it tap the Send 1 control before resetting Cubase does not se
5. area away from a fader cap and drag left or right Each swipe will bank left or right one channel at a time Keep your finger down and keep dragging to increment more than one channel Level Meter The channel strip contains a multi segment meter display that displays the signal level of the channel s audio Clear Peaks Touch the peak indicator on any given meter to clear its red peak overload indicator Solo Touch the solo button to solo the channel Press it again to turn off solo Mute Touch the mute bottom to mute the channel Press it again to unmute the channel Record Touch the record button to record arm the channel Press it again to record safe the channel Insert Plug In Editing Touch the INS button of a channel to display the insert plug in display where you can adjust parameters of plug ins inserted on the channel For more information see the section titled Insert Plug In Editing Popup Window Automation Mode Touch the A button of a channel to display the automation mode popup window which allows selection of the following different automation modes 8 V Control 1 2 User s Guide Off Turns automation for the channel off Read Switches the channel to automation read mode Touch Switches the channel to automation touch mode Latch Switches the channel to automation latch mode Write Switches the channel to automation write mode Trim Switches the channel to automation trim mode St
6. Keys Popup Window for further details Set Left L Touch this button to set a mark in point at the current location of the play head Set Right R Touch this button to set a mark out point at the current location of the play head Punch L Touch this button to set an auto punch in point at the current location of the play head Punch R Touch this button to set an auto punch out point at the current location of the play head Save Touch this button to save the current session Undo Touch this button to undo the last performed action of the session Redo Touch this button to redo the last performed action of the session V Control 1 2 User s Guide 37 Bottom of Screen Controls The buttons on the bottom of the V Control interface work as follows Settings Touch this button to bring up the V Control settings screen Touch it again to return to the main interface Banking Popup Window Touch this button to bring up the banking popup window which contains 4 buttons that allow banking the displayed channels left or right either 1 or 8 channels at a time These buttons serve as an alternate interface for bank channel increment decrement for users who prefer this method to the one finger two finger swiping method described above Time counter This display displays the current time location in Logic It can display the session counter as SMPTE minutes seconds or bars and beats Big Counter Display Touch the left area
7. buffer into the session at the current location of the play head Delete Touch this button to delete the currently selected audio clip removing it from the session Navigation Scrub Shuttle Strip Swiping this strip moves the play head back and forth within the session Scrub Button Touch this button to switch the scrub shuttle strip into scrub mode resulting in audio playing back as long as the strip is manipulated with one s finger Shuttle Button Touch this button to switch the scrub shuttle strip into shuttle mode resulting in audio playing back as long as the strip is manipulated with one s finger Audition Touch this button to perform the audition function on a selected audio clip Cursor Diamond Nav Zoom Select Touch this button to toggle the use of the cursor diamond between Zoom Mode In this mode the cursor up down keys adjust the waveform height of the tracks while the cursor left right keys adjust the zoom level of the edit timeline Nav Mode In this mode the cursor up down keys allow you to select a track while the cursor left right keys allow selection of audio regions within a track V Control 1 2 User s Guide 15 Modifiers Popup Window This popup offers several modifier keys duplicating the modifier keys found on a standard computer keyboard These keys provide variant functions when used in conjunction with other commands 16 Touch the modifiers button at the lower left side
8. in point at the current location of the play head Set Right Touch this button to set a mark out point at the current location of the play head Save Touch this button to save the current session Undo Touch this button to undo the last performed action of the session V Control 1 2 User s Guide 25 Bottom of Screen Controls The buttons on the bottom of the V Control interface work as follows Settings Touch this button to bring up the V Control settings screen Touch it again to return to the main interface Banking Popup Window Touch this button to bring up the banking popup window which contains 4 buttons that allow banking the displayed channels left or right either 1 or 8 channels at a time These buttons serve as an alternate interface for bank channel increment decrement for users who prefer this method to the one finger two finger swiping method described above Time counter This counter displays the current time location in Cubase Nuendo mirroring the time format currently used in the application s counter window Big Counter Display Touch the left area of the counter display to show or hide the Big Counter which displays the counter at a much larger size Touch the left area of the counter to hide the Big Counter display Note that you can still touch the faders with the big counter display active Transport Popup Window Touch the right hand side of the counter to toggle the transport popup window on
9. it can simply be double tapped repeatedly to toggle between the two states of the parameter If more than 16 parameters are present for the select plug ins tap the lt page and page gt buttons to navigate to the different pages of parameters To adjust the plug ins for a different channel in Logic simply select a different channel in the V Control mixer interface which can be done without having to close the plug in window Note that although Logic will allow more than 12 plug ins to be inserted into a track V Control only allows adjustment of the first 12 plug ins Important Tip Logic requires a track to be in the Arrange window for a control surface to access the plug in inserts By default aux output and master tracks do not get placed in the Arrange window which means that plug ins for these tracks will not be controllable by V Control To eliminate this restriction simply move these tracks to the arrange window by selecting them and then using the key command Control T Known Issues with V Control 1 2 and Logic If Ney Fi is updated to fix problems or add features it will be necessary to manually remove V Control from Logic s controller setup window in preferences then re perform the initial setup procedure see setup section for details 42 V Control 1 2 User s Guide
10. of the app to display the modifier keys popup window Touch each modifier key you want to be active the modifier keys will hold their current state so you don t have to keep a finger on them while you re using them All modifier keys will be deactivated when you close the modifier buttons display The four modifier keys behave the same way as when used from a computer keyboard within Pro Tools o Shift emulates the Shift key on a computer keyboard o Control emulates the Control key on a computer keyboard o Option emulates the Option key on a computer keyboard o Command emulates the Command key on a computer keyboard Pressing the default key disengages any previously activated modifier keys V Control 1 2 User s Guide Keypad Popup Window The keypad popover provides a numeric keypad that provides many control features for Pro Tools and works as follows Note that Pro Tools must be the foreground app on the computer and will not receive the keypad commands if it is in the background Clear Touch this button to clear any previously entered values from the counter window z Capture Time Code Touch this button to capture the value of any time code currently entering the session and enters it into the session s time code window Enter Start End Length Touch this button in conjunction with the numbers keys to assign a start and end time to the session Enter Main Counter Touch this button in c
11. of the counter display to show or hide the Big Counter which displays the counter at a much larger size Touch the left area of the counter to hide the Big Counter display Note that you can still touch the faders with the big counter display active Transport Popup Window Touch the right hand side of the counter to bring up the transport popup window which offers additional transport related controls Touch the right hand side of the counter again to close the popup window See section entitled Transport Popup Window for details Loop Touch this button to turn on the loop playback function in Logic Touch it again to turn the loop function back off Metronome Touch this button to turn on Logic s internal metronome Touch it again to turn the metronome back off Go To Left Touch this button to move the play head to the current mark in point of the session Go To Right Touch this button to move the play head to the current mark out point of the session Rewind Touch this button momentarily to rewind the play head backwards by one beat Press and hold the button to rewind the play head which will keep rewinding until the stop button is pressed Fast Forward Touch this button momentarily to advance the play head forward by one beat Press and hold the button to fast forward the play head which will keep fast forwarding until the stop button is pressed 38 V Control 1 2 User s Guide Stop Touch this button to stop the
12. off which offers additional transport related controls See section entitled Transport Popup Window for more details Go to Left L lt Touch this button to move the play head to the current mark in point of the session Go to Right R gt Touch this button to move the play head to the current mark out point of the session Go to Start lt Touch this button to move the play head to the very start of the current session Go to End gt Touch this button to move the play head to the very end of the current session Rewind Press and hold the button to rewind the play head Fast Forward Press and hold the button to fast forward the play head Loop Touch this button to toggle the transport loop function on off The button illuminates when the loop function is active 26 V Control 1 2 User s Guide Stop Touch this button to stop the transport of the current session Play Touch this button to start playback of the current session Record Touch this button to punch in to record in the current session The button illuminates in red when recording is active Touch the play button to punch out of record Transport Popup Window The transport popup window provides additional transport related controls and works as follows Auto Punch Touch this button to toggle the auto punch in function on off The button illuminates when the auto punch function is active Edit Keys Popup Window The edit keys popup wind
13. tent to tst ttn nnna 18 Insert Plug In Editing Popup Window esse iee treten tente ttnntttn tent tette ttn tta tentes 19 Known Issues with V Control 1 2 and Pro Tools eene ttn tnnntnnntnnnnns 20 Using V Control with Cubase Nuendo censes eene eere eene enun sentent een 21 Setting up V Control as a Control Surface in Cubase Nuendo s 21 Channel Strip Interface deiecti me orc NA HORS duque 22 Right Hand side Controls a a onus fecti pictae 24 Bottom of Screen COntro s 5 ntt ayi aiai ta cbe c n nk dn a rnb v abu 26 Transport Popup Wind Ow ecce territi oerte ct tr dx en re Do estia a re Dee este eh dog 27 Edit Keys Popup Window s eese tentat tttn tnnt tents tte tena tattoo tena totes danian 27 Locator Popup WindOW ederet etin Ret prb ttp eerie ERR tiet bn ipa Heap a 29 Channel Popup Window sienten tentant tnnt tenta tte ttt tent tattoo ttt tena torso ttt ttta sona ni 30 Known Issues with V Control 1 2 and Cubase Nuendo entrent 32 Using V Gontrol WITH EOgIG ii in hao FREE RVR FEE FE FEEEXR YEPR TREES EEEVR REED FERE FERE RE ERE REPE RF Ta PU 33 Setting up V Control as a Control Surface in Logic sesenta 33 Channel Strip Interface eee aiaa reca co debe ae ueste tiere anto eL igne 35 Right Hand Side Controls ss siesseen tentaret tent tents ttn ttt tent to tetto tenta 37 Bottom of Screen Control
14. to install the Ney Fi app MIDI driver and runtime libraries The runtime libraries installer is a separate installer that you will need to authorize Make sure to also install Bonjour if it is not already installed o Mac Installer Drag the downloaded Ney Fi icon to your applications folder Connect your computer to your chosen local network Launch Ney Fi V Control 1 2 User s Guide 5 o Windows Launch Ney Fi from the program list in the Ney Fi section o Mac Launch Ney Fi from the applications folder Ney Fi is a simple menu bar only application on the Mac and a system tray application on Windows thus there is nothing for you to configure on either operating system General Troubleshooting 6 Verify the iPad and target DAW computer are connected to the same local area network Verify that the Ney Fi utility is running on your host DAW computer On Mac OS X Ney Fi operates as a menu bar application On Windows Ney Fi operates as a system tray utility Verify that V Control sees the DAW computer on the network by touching the gear icon to display the Setup window Look at the computer picker to verify that your computer is both listed and selected Verify that you have selected V Control as the MIDI input and output source in the control surface setup window of your DAW Verify that Bonjour is installed on your Windows systems Verify that firewall blocking is disabled for Ney Fi V Control 1 2 User s Guide
15. Touch this button to toggle the Logic floating transport bar on off Environment Touch this button to toggle the Logic environment window on off Audio Pool Touch this button to toggle the Logic audio pool window on off 40 V Control 1 2 User s Guide Sample Editor Touch this button to toggle the Logic sample editor window on off Markers Touch this button toggle the Logic markers window on off Screen Set Section Touch any of these 9 buttons to switch to 9 different screen sets that you have configured in Logic Markers and Jog Scrub Section This section allows the user to quickly navigate to different marker positions as well as jug scrub the play head 1 9 Touch any of these buttons to go straight to a marker with one button press all while staying in the edit window Prev Touch this button to navigate to the previous marker Next Touch this button to navigate to the next marker Jog Scrub Strip Swipe this strip with in a left or right motion to jog the play head along the timeline Touch the transport s pause button to put the transport into pause mode which will allow the jog scrub strip to now act as a scrub control As you swipe along the strip the track will audibly scrub back and forth Touch the pause button again to take the transport out of pause mode The jog scrub strip now operates in jog mode again Plug In Editing Popup Window The insert plug in editing window allows you to adjust parameters of an i
16. V Control Version 1 2 User s Guide www neyrinck com V Control 1 2 User s Guide 1 Table of Contents Welkome to V C ntrol anssen Ria Ee DURHURRERAS FEE TALES a EHE DI E PUE E HAE TERM XPETDMEL UE 3 figli M 3 fO 1UITe eI EDT CITIES LS a 4 Setting up V Control for use with your DAW seien tenta tnnt tent tents ttt tttn nn 4 Using V Control sisi c 4 Setting Up a Local Network with Wi Fi scccssscccsseeccsseeccssecccsseccnsscecsscecsesecaneeees 5 Installing us RE 5 General Troubleshooting cincscccscesiiccuteccecteateercisessieshceseestuctateschinteanecterestcesdersudesactesctestectantelietdksesecsntdtiaschietaneceent 6 Using V COntrol with Pro ToDls eris io o ssavessnateavaes secseacscassietesedsessssceussedsedsssanies 7 Setting up V Control as a Control Surface in Pro Tools sees 7 Important Windows Information for Pro Tools 9 eise eerte tnnt tents 7 Channel Strip loli utc RE m m 8 Right Hand Side Controls heri Iit bari aa ipee a pd 10 Bottom OF Sere et oliudsc E 11 Transport Popup WindOW aiit tette iet anand dealin wlth ceca eda do inde ud 12 Edit KEYS Pop p loo iiaa naat 12 Modifiers Popup WIndOW niu titre cerca tetendit Rc a Get 16 Keypad dita 17 Surround Pan Popup Window eise tentent tenta ttt teta tents tatto
17. ary controls now adjust panning for each channel The pan pot will display the pan position and at the same time a pan value will be displayed as a numerical value inside the pan pot The rotary encoders operate as follows when used to adjust channel auxiliary sends V Control 1 2 User s Guide 35 Touch one of the buttons 1 8 on the right hand side of V Control to select which of the 8 aux sends in Logic to adjust The rotary controls now control the aux send level for the selected send Tap the center of a rotary control to toggle the send on off allowing for quick and easy bypassing of the channel aux send Mute M Touch the mute button to mute the channel Press it again to unmute the channel Solo S Touch the solo button to solo the channel Press it again to un solo the channel Input Monitor I Touch the I button to turn on input monitoring for the channel Touch it again to turn the input monitoring off Record R Touch the record bottom to record arm the channel Press it again to record safe the channel Fader Touch the fader and drag it up and down to adjust the signal level of the channel Since the iPad uses a multi touch interface multiple faders can be adjusted at once just like on a real hardware mixer The fader cap displays the current gain level for the channel Level Meter The channel strip contains a detailed level meter that displays the signal level of the channel s audio Bank Increme
18. atus Display the current automation mode status of the selected channel Rotary Encoders These virtual knobs allow you to adjust both channel panning as well as send levels A E for the relevant Pro Tools channel when used in conjunction with the Pan and A E buttons on the right hand side To adjust the rotary encoder touch the encoder and swipe using an up down or side to side motion The rotary encoders operate as follows when used to adjust stereo panning Touch the Pan button again to switch between the Left and Right pan controls when working with a stereo track the Pan button blinks when the right panner is active The rotary encoders operate as follows when used to adjust channel auxiliary sends Touch buttons A B C D or E to select which of the five aux sends in Pro Tools to adjust Tap the center of the rotary control to toggle the send between pre fader and post fader status V Control Pro only A mute button is also present below the sends When this button is toggled on tapping the center of the encoder will mute the send as opposed to toggling its pre post status V Control 1 2 User s Guide 9 Right Hand Side Controls The buttons on the right hand side of the screen control various additional functions and work as follows Pan Touch this button to switch the rotary encoders to panning mode allowing the user to adjust L R panning of each channel by swiping the onscreen v pot A E Touch any of
19. d along the strip Press the scrub button again to put the strip back into normal jog mode Shuttle Button Touch this button to put the scrip into shuttle mode The jog strip now works like a shuttle wheel with the play head moving on its own after the strip has been used to give it momentum Press the shuttle button again to put the strip back into normal jog mode Cursor Diamond The cursor diamond works in two modes Select and Zoom Select Mode In this mode the cursor center key is not illuminated and the cursor keys work as follows The cursor up down buttons navigate which channel is selected The cursor left right buttons navigate among the selected channel s audio clips selecting each clip in series as the cursor buttons are pressed Zoom Mode In this mode the cursor center key is illuminated green and the cursor keys work as follows The cursor up down buttons zoom the height of the session tracks to be taller shorter The cursor left right buttons zoom the height of the session tracks to be taller shorter 28 V Control 1 2 User s Guide Locator Popup Window The locator popover provides a numeric keypad that provides many control features for Cubase Nuendo and works as follows e Use the number buttons to enter a numerical value for a desired location and then press the Set Position button to go to location e Enter a number and then press Move Back to move the current location back by that amo
20. ed channel and adjust their parameters Adjusting EQ When the popup window s EQ button is pressed the popup window displays EQ in the upper left hand corner and the window works as follows Band Selection Swipe the top of the popup window to select among the 4 bands of EQ that can be adjusted Each band of EQ has its own page of controls as follows Page 1 Low Band Page 2 Low Mid Band Page 3 High Mid Band Page 4 High Band Gain Rotate this control to adjust the boost cut of the currently selected EQ band Frequency Rotate this control to adjust the center frequency of the currently selected EQ band 30 V Control 1 2 User s Guide Q Rotate this control to adjust the Q bandwidth of the currently selected EQ band On Off Rotate this control to toggle the EQ on off for the specific band of EQ that is currently displayed Toggle Button Touch this button to toggle all 4 bands of EQ on off for the currently selected channel Adjusting Sends When the popup window s Sends button is pressed the popup window will display FX Send in the upper left hand corner providing an alternate sends interface to the one at the top of the channel strip The window works as follows Send Selection Swipe the top of the popup window to select which of the 8 channel sends to adjust The page number in the upper right hand corner of the window corresponds to the currently selected send for example page 5 of 8 means y
21. er display to show or hide the big counter which will show the scrolling time value at a much larger size Note that you can still touch the faders with this display active Touch the same spot on the counter again to close the big counter window Pre Roll Touch the pre roll area of the counter to toggle the Pro Tools pre roll function on when playing or recording Touch the pre roll area again to turn pre roll off Post Roll Pressing the post roll area of the counter to toggle the Pro Tools post roll function on when playing or recording Touch the post roll area again to turn post roll off Online Touch this button to toggle the Pro Tools session s online chase status on off Return to Zero Touch this button to move the playback cursor to the start point of the project Rewind Touch this button to move the playback cursor backwards within project V Control 1 2 User s Guide 11 Fast Forward Touch this button to move the playback cursor forwards within the project End Touch this button to move the playback cursor to the end point of the project Stop Touch this button to stop the transport of the current session Play Touch this button to start playback of the current session Record Touch this button to begin recording in the current session Transport Popup Window The buttons in the transport popup window offer additional transport related commands and work as follows Loop Touch this button to toggle
22. face to the edit window Mix Touch this button to switch the Pro Tools main interface to the mix window Memory Touch this button to toggle the Pro Tools memory locators window on off Transport Touch this button to toggle the Pro Tools transport window on off Ins pl Touch this button to toggle the Pro Tools insert in place function on off Setup Touch this button to toggle the Pro Tools session setup window on off Auto Write Vol Touch this button to toggle the channel volume automation parameter on off when any channels are in automation write mode Pan Touch this button to toggle the channel pan automation parameter on off when any channels are in automation write mode Send Vol Touch this button to toggle the channel send volume automation parameter on off when any channels are in automation write mode Plug in Touch this button to toggle the channel plug in automation parameter on off when any channels are in automation write mode Mute Touch this button to toggle the channel mute automation parameter on off when any channels are in automation write mode Send mute Touch this button to toggle the send mute automation parameter on off when any channels are in automation write mode V Control 1 2 User s Guide 13 Mode Shuffle Touch this button to switch the Pro Tools editing grid to shuffle mode Spot Touch this button to switch the Pro Tools editing grid to spot mode Slip Touch this button t
23. hannel name in the DAW software itself Channel Select Touch the track name at the top of a channel to select that channel The selected channel changes to light grey to show it has been selected Panning Aux Level Controls These controls allow you to adjust both channel panning as well as send levels 1 8 for the channel Their specific function is selected using the Pan 1 4 and 5 buttons on the right hand side of the V Control interface The level controls work as follows when used to adjust stereo panning Touch the pan button on the right hand side of V Control The horizontal swiping motion now controls panning for each channel A vertical blue line will indicate the current panning position The level controls work as follows when used to adjust channel auxiliary sends To adjust one of the first four aux sends touch one of the buttons 1 4 on the right hand side of V Control To control aux sends 5 8 touch the 5 button repeatedly it will scroll through values 5 6 7 and 8 allowing you to select any of those aux sends Swipe the level controls in to increase decrease the level of the selected aux send Tap the center of the control to toggle the send on off allowing for quick and easy bypassing of the channel aux send The send bypass function can also be controlled by the send bypass button further down on the channel strip Mute M Touch the mute bottom to mute the channel Press it again to unm
24. indow Touch this button to toggle the GUI window on off for the selected plug in Bypass Touch this button to bypass all inserts on the relevant channels Compare Touch this button to toggle between the last adjusted parameter and the previous setting allowing an A B comparison of a parameter adjustment V Control 1 2 User s Guide 19 Known Issues with V Control 1 2 and Pro Tools 20 The Create Location button in V Control Pro will not operate correctly if Pro Tools has the setting Use Separate Play and Stop Keys enabled You may instead use the keypad to create e memory location by typing period and enter The Grab Tool button in V Control Pro will only cycle you through the Separation and Object Grab tools You must select the Time Grab Tool directly in Pro Tools The Zoom Preset buttons 1 4 will not operate correct unless you press Recall or Store before you select them Loop Record mode is not indicated The HUI protocol that V Control uses does not provide the ability to display it but does allow it to be switched using the keypad Pro Tools must be in the foreground to receive commands via the Keypad popover Pro Tools must be in the foreground to use the zoom presets memory locations tool select edit mode select features in the Edit popover V Control Pro only V Control 1 2 User s Guide Using V Control with Cubase Nuendo Setting up V Control as a Control Surface in Cubase Nuendo To use V Contr
25. l plug in parameter automation on off in the current session V Control 1 2 User s Guide 39 Solo Touch this button to toggle all solo parameter automation on off in the current session Command Section This section contains various editing commands Cut Touch this button to cut the currently selected audio clip removing it from the session but also copying it into the copy buffer memory Copy Touch this button to copy the currently selected audio clip into the copy buffer memory Paste Touch this button to paste the audio clip that is currently residing into the memory buffer into the session at the current location of the play head Delete Touch this button to delete the currently selected audio clip removing it from the session Select All Touch this button to select all clips residing on the currently selected track Window Section This section contains buttons for toggling various Logic windows on off Arrange Touch this button to toggle the Logic arrange edit window on off Mixer Touch this button to toggle the Logic mixer window on off Event Touch this button to toggle the Logic event editor window on off Score Touch this button to toggle the Logic notation scoring window on off Transform Touch this button to toggle the Logic transform window on off Hyper Touch this button to toggle the Logic hyper editor window on off Piano Touch this button to toggle the Logic Piano View window on off Transport
26. mation read write button displays as R then the individual channel automation buttons is set to W and automation write status can be toggled on off on a per channel basis Clear Mutes M Touch this button to unmute any and all channels that are currently muted Clear Solos S Touch this button to un solo any and all channels that are currently soloed Mixer Touch this button to toggle the Cubase session between its mixer and edit windows Soft Keys 1 and 2 These buttons can be custom configured to perform many different assignable functions with Cubase Nuendo To configure the soft keys Within Cubase Nuendo select the devices menu then select device setup In the Remote Devices column on the left select Mackie HUI On the right hand side you will see a column labeled button with two entries Audition which corresponds to Soft Key 1 and Window A which corresponds to Soft Key 2 Click on the category and command columns to select among the available Cubase Nuendo functions Click apply and then OK The two soft keys will now control the two functions you have assigned Edit Touch this button to bring up the V control Edit Keys popup window See the section titled Edit Keys Popup Window for more details Locate Press thus button to toggle the Locator Window On Off See the section titled Locator Popup Window for more details Set Left Touch this button to set a mark
27. mute solo and automation controls It contains the following controls from top to bottom Channel Name Display This display at the top of each channel displays the name of the channel matching the channel name in the DAW software itself Channel Select Touch the track name at the top of a channel to select that channel The selected channel changes to light grey to show it has been selected Automation Mode The thinner text box below the channel name is the automation display It displays the current automation state for that channel Touch the text box to display the automation mode popup menu where the channel s different automation modes can be selected including Off Turns automation for the channel off Read Switches the channel to automation read mode Touch Switches the channel to automation touch mode Latch Switches the channel to automation latch mode Write Switches the channel to automation write mode Rotary Encoders These virtual knobs allow you to adjust both channel panning as well as auxiliary send levels 1 8 for the relevant channel Their specific function is selected using the Pan and 1 8 buttons on the right hand side of the V Control interface To adjust the rotary encoder touch the encoder and swipe using an up down or side to side motion The rotary encoders operate as follows when used to adjust stereo panning Touch the pan button on the right hand side of V Control The rot
28. nserted plug in It works as follows Touch the channel name at the top of a channel to select the channel whose plugins you wish to highlight o Note that the plug in editing window only works for plug ins that are inserted on an audio track Plug ins that resides on an auxiliary return or master fader cannot be edited Touch the plug in button to bring up the plug in window A vertical row of buttons on the left hand side of the window will display the names of any plug ins that have been inserted into the channel s 12 V Control 1 2 User s Guide 41 available plug in slots Each of these buttons can be touched to allow adjustment of that specific plug in s individual parameters A second row of vertical buttons allow you to toggle on off the bypass status of any individual plug in The button illuminates to show if a plug in is currently bypassed As you select a specific a plug in from the 12 buttons on the left the names and parameter values of the various plug in s parameters are displayed on 16 separate rotary controls Adjust the rotary controls to change the setting of a specific plug in parameter A rotary control can be double tapped to change the control to its minimum position A 2 double tap will then change the control to its maximum position This approach is particularly useful for parameters that only have a 2 position state such as on off Instead of rotating the control to select between the two states
29. nt Decrement Using two fingers swipe the surface in the fader area but not in the area of a fader cap in a left or right motion Each swipe will bank left or right eight channels at a time Channel Increment Decrement Using one finger touch the surface in the fader area but not in the area of a fader cap and drag in a left or right motion Each swipe will bank left or right one channel at a time Keep your finger down and keep dragging to increment more than one channel 36 V Control 1 2 User s Guide Right Hand Side Controls The buttons on the right hand side of the V Control interface work as follows Pan Touch this button to switch the rotary encoders to panning mode 1 8 Touch any of these 8 buttons to switch the V pots into auxiliary send control for sends 1 8 Clear Mutes M Touch this button to unmute any and all channels that are currently muted Clear Solos S Touch this button to un solo any and all channels that are currently soloed Group Suspend Touch this button to suspend all track groups that have been created Pressing the button again will resume the normal grouping function Plug in Touch this button to bring up the plug in editing window for the currently selected channel See the section titled Plug In Editing Popup Window for more details Touching the button a second time closes the window Edit Touch this button to bring up the V control Edit Keys popup window See the section titled Edit
30. ntrol and display Automation and group status display Automation and Group suspend control Window select controls for edit mix locations transport setup and plug in Locations 1 8 hot keys Edit tool select buttons Zoom preset buttons Edit command buttons V Control 1 2 User s Guide 3 Quick Start Setting up V Control for use with your DAW Launch the Ney Fi wireless hosting application on your Mac or Windows system See details below on installing Ney Fi Ney Fi must be running in order for the V Control app on the iPad to communicate with the DAW running on your computer Configure the connections in your specific DAW as per the instructions in the appropriate section of the user s manual Within the V Control app itself select the gear icon button to display the settings window o In this window s Computer Picker section select the target computer you wish to connect to o In this window s DAW section select the specific DAW you wish to connect to Enjoy Using V Control V Control s Interface consists of four main areas The channel strip interface that displays eight channels of the DAW ata time A vertical row of buttons on the right hand side of the screen offering various functions and shortcuts A horizontal row of controls on the bottom of the screen offering mainly transport commands and a time counter Various popup windows for additional functions 4 V Control 1 2 User s Guide
31. o switch the Pro Tools editing grid to slip mode Grid Touch this button to switch the Pro Tools editing grid to grid mode Zoom Preset Store Touch this button to store the current zoom settings into a zoom preset when used in conjunction with one of the 1 4 buttons Recall Touch this button to recall one of the four stored zoom settings when used in conjunction with one of the 1 4 buttons 1 4 Used in conjunction with the store and recall buttons as described above Tool Trim Switches the computer cursor to the trim tool Zoom Switches the computer cursor to the zoom tool Select Switches the computer cursor to the select tool Scrub Switches the computer cursor to the scrub tool Grab Switches the computer cursor to the grab tool Pencil Switches the computer cursor to the pencil tool Command Capture Touch this button to issue the capture command in Pro Tools Separate Touch this button to issue the separate command in Pro Tools dividing the selected audio clip into two separate ones at the current location of the play head Cut Touch this button to cut the currently selected audio clip removing it from the session but also copying it into the copy buffer memory 14 V Control 1 2 User s Guide Copy Touch this button to copy the currently selected audio clip into the copy buffer memory Paste Touch this button to paste the audio clip currently residing into the memory
32. o work with V Control This is due to a Pro Tools 9 bug where it won t send MIDI out the V Control MIDI node without running as Administrator Bonjour Ney Fi uses Bonjour to locate V Control and the iPad on your network Separate installers for Bonjour are provided if you need to install it If you don t know if it is installed launch the installer and if it gives you an option to repair or remove that means it is already installed V Control 1 2 User s Guide 7 Channel Strip Interface The channel strip interface is the area that allows adjusting levels and panning adjusting sends and working with mute and solo controls It contains the following controls from top to bottom Channel Name V Control will automatically display the name of your Pro Tools track at the top of the channel in an abbreviated form Channel Select Touch the scribble strip at the top of channel to select a channel Use the modifier buttons to manage selection and operations on multiple channels Fader Touch the fader and drag it up and down to adjust the signal level of the channel Since the iPad uses a multi touch interface multiple faders can be adjusted at once just like on a real hardware mixer Bank Increment Decrement Using two fingers touch the surface in the fader area away from a fader cap and swipe left or right Each swipe will bank left or right eight channels Channel Increment Decrement Using one finger touch the surface in the fader
33. ol with the Macintosh OS X or Windows versions of Cubase or Nuendo perform the following steps Launch the Ney Fi application Launch the V Control app on your Ipad In the settings screen of V Control select the computer tab and then select the computer that Cubase is running on In the DAW tab select Cubase Launch Cubase on your computer In Cubase select Controllers in the windows menu Follow the steps outlined in Cubase s documentation for adding a Mackie HUI control surface V Control works with Cubase Nuendo by emulating certain elements of the HUI hardware in software form When selecting MIDI input and output ports for the HUI in the Cubase Nuendo Window select V Control as the MIDI source and destination Close the Cubase controllers window V Control and Cubase Nuendo should now have complete bi directional control with each other Verify operation by adjusting the faders and transport controls in both the V Control app and the Cubase Nuendo software Actions performed in the Cubase Nuendo software and V Control should be reflected in the other V Control 1 2 User s Guide 21 Channel Strip Interface The channel strip interface is the area that allows adjusting levels and panning adjusting sends and working with mute and solo controls It contains the following controls from top to bottom Channel Name Display This display at the top of each channel displays the name of the channel matching the c
34. onjunction with the number keys to enter a time code value into the main session counter window Nudge Back Touch this button to nudge a selected audio clip backwards in time by the assigned nudge value Nudge Forward Touch this button to nudge a selected audio clip forwards in time by the assigned nudge value Enter Create Memory Location Touch this button to create a new memory location at the current location of the play head 1 Rewind Touch this button to move the playback cursor backwards within the project 2 Fast Forward Touch this button to move the playback cursor forwards within the project 3 Record Touch this button to begin recording in the current session 4 Loop Playback Touch this button to toggle the loop playback function on off 5 Loop Record Touch this button to toggle the loop record function on off 6 Quick Punch Touch this button to toggle the Pro Tools Quick Punch function on off allowing you to perform live recording punches in the session 7 Metronome Touch this button to toggle the audible metronome on off 8 Count Off Touch this button to toggle the count off function on off 9 Merge Replace Touch this button to toggle the Pro Tools merge replace function on off V Control 1 2 User s Guide 17 Surround Pan Popup Window The surround pan window allows you to control surround panning of a track when Pro Tools is set up with a surround mixer as opposed to stereo
35. ou are currently adjusting send 5 Level Rotate this control to adjust the level of the currently selected send FX On Off Rotate this control to turn the selected send on off using it as a send bypass control FX Pre Rotate this control to toggle the send between pre fader and post fader status When the rotary control is illuminated the send is configured as pre fader Toggle Button Touch this button to toggle all 8 sends on off for the selected channel Adjusting Input output Routing When the popup window s Routing button is pressed the popup window displays Routing in the upper left hand corner and the window works as follows Output Bus Rotate this control to select among the available audio outputs offered by the audio interface hardware The display above the rotary control shows all input connections as the control is rotated Monitor Rotate this control to toggle input monitoring on off for the Input Bus Rotate this control to select among the available audio inputs offered by the audio interface hardware The display above the rotary control shows all output connections as the control is rotated V Control 1 2 User s Guide 31 Swipe the top of the popup window to navigate to the 2 page of controls which includes Phase Rotate this control to invert the phase of the channel s audio by 180 Gain This control has no effect in current versions of Cubase Nuendo 73 Adjusting Inserts
36. ow provides a large variety of additional controls with its contents divided up into different sections The buttons in the Edit Keys Popup window work as follows Command Section This section contains various editing commands Cut Touch this button to cut the currently selected audio clip removing it from the session but also copying it into the copy buffer memory Copy Touch this button to copy the currently selected audio clip into the copy buffer memory Paste Touch this button to paste the audio clip that is currently residing into the memory buffer into the session at the current location of the play head Delete Touch this button to delete the currently selected audio clip removing it from the session Window Section This section contains buttons for toggling various Cubase windows on off Marker Touch this button to toggle the markers window on off Transport Touch this button to toggle the session s transport window on off V Control 1 2 User s Guide 27 CPU Touch this button to toggle the session CPU percentage window on off Navigation Section This section contains buttons for navigating among the session as well as changing zoom levels Jog Scrub Strip Swipe this strip with in a left or right motion to move the play head along the timeline Scrub Button Touch this button to put the scrip into scrub mode The scrub button illuminates and the jog strip now audibly scrubs the audio as a finger is swipe
37. ox as it is very important to have Logic always automatically detect attached control surfaces in order for V Control to work correctly with Logic Updated versions of V Control and Logic If you are setting up V Control and Logic and it is NOT the first time you have done the setup process such as using a post 1 2 update of the V Control app it is important to manually remove the existing V Control profile from Logic so that the new version of V Control can be automatically detected V Control 1 2 User s Guide 33 34 This removal process can be done with the following steps In the Logic drop down menus select Preferences Control Surfaces Setup In the setup window that appears you will see a large icon labeled V Control Highlight the icon and press the keyboard s delete key to delete it Confirm your decision to delete the profile when asked in the resulting dialog box Before closing the setup dialog box click on the new tab at the top and make sure that automatic installation is checked Quit Logic At this point you may follow the steps for setting up V Control with Logic as described on the previous page with the confidence that the latest installed version of the V Control app will be automatically detected and used by Logic V Control 1 2 User s Guide Channel Strip Interface The channel strip interface allows adjustment of channel levels adjusting of panning and aux sends and working with
38. reen control various additional functions and work as follows Pan Touch this button to switch the channel pan aux controls to panning mode 1 4 Touch any of these 4 buttons puts to switch the channel pan aux controls into auxiliary send control for sends 1 4 5 Touch this button to cycle through controlling aux sends 5 6 7 and 8 The display will change to show which aux send is currently being controlled by the channel level controls Pre Post Touch this button to toggle the channel send button between two different functions Pre Post In this mode the master pre post button is lit orange and the channel sends buttons toggle each channel s send between pre fader and post fader status for the currently selected aux send Send Bypass In this mode the master pre post button is not illuminated and the channel send buttons act as a bypass control for the currently selected aux send Automation On Off R Touch this button to toggle automation on off for all channels in the current session The button illuminates to show when automation for all channels is armed Automation Read Write R or W Touch this button to toggle the function of the individual channel automation buttons o When the automation read write button displays as R then the individual channel automation buttons is set to R the automation read status can be toggled on off on a per channel basis 24 V Control 1 2 User s Guide o When the auto
39. s toe iere a TA 38 Transport Popup Window s sadid ingadanan tttm te nter ttta tent ta ttes tagi neradi aakit 39 Edit Keys Popup WindOW eei iiiter terreri nente epe ire baba aan reed pe uie ebrei 39 Plug In Editing Popup Window isses tentaret tttn tent tents ttn ttt tent toto ttt ttta tenta 41 Known Issues with V Control 1 2 and Logic sess tentnttnttnnttnn tentes 42 2 V Control 1 2 User s Guide Welcome to V Control V Control Pro is an iPad app that provides a virtual multi touch control surface for Digital Audio Workstation DAW software applications including Pro Tools Logic and Cubase Nuendo V Control acts as a multi touch control surface allowing the user to access transport editing and mixing functions on both Macintosh OS X and Microsoft Windows systems In tandem with your iPad V Control s portability small footprint and ease of use provide a powerful addition for the user Features V Control offers the following features feature set varies by specific DAW Edit send volume pan mute and pre post controls Flip mode send editing Automation mode select and display for each channel Automation write enable disable for volume pan mute send volume send mute and plug ins Input Output and Insert assignments Plug In editing Scrub and shuttle control Auditioning pre roll in out and post roll Navigation Zoom Select switch quadrant Transport online offline control Channel select co
40. t and send panners on the focused track so that you can select a panner to control Down Window Button Touch this button to toggle on off the panner window of the targeted main output or send in your Pro Tools session Right Button Touch this button to toggle focus between panners on a stereo track allowing you to choose between surround panning of the left or right side of the track in a single surround pan screen 18 V Control 1 2 User s Guide Insert Plug In Editing Popup Window The insert plug in editing window allows you to adjust parameters of an inserted plug in It contains the following displays and controls Rotary Controls These four controls perform two separate functions e Selects a specific plug in to assign to an insert slot e Adjust parameter values for an assigned plug in Parameter Displays These four display slots show the currently assigned plug ins and plug in parameters When working with the parameter displays use your finger to swipe the LCD text display in a left or right direction to move between additional control pages Assign Touch this button to assign a plug in to the relevant channel Ins Params Touch this button to toggle the parameter display between two functions Insert Mode The display shows what plug ins are assigned to a particular insert Parameter Mode The display show the parameters available to a selected plug in allowing them to be adjusted with the rotary controls W
41. t V Control s counter when first launching or resetting Cubase will refresh the counter when it changes to a new value 32 V Control 1 2 User s Guide Using V Control with Logic Setting up V Control as a Control Surface in Logic To set up V Control for use with Logic for the first time perform the following steps Launch the Ney Fi application Launch Logic Launch the V Control app on your Ipad In the settings screen of V Control select the computer tab and then select the computer that Logic is running on In the DAW tab select Logic Since V Control acts as a native Logic control surface Logic should automatically detect the V Control app as a valid control surface once it has finished launching Logic will then display a message that it has detected a new control surface called V Control and will offer to add it to its list of supported control surfaces Click OK At this point the computer running Ney Fi will be available to choose from in the computer picker in the settings window V Control and Logic will now have complete bi directional control of each other IMPORTANT NOTE When Logic presents the dialog box that it has detected a new control surface it will offer a checkbox option that says Do not display this window again Checking this box will turn off the automatic discovery process of new control surface and thus turn off automatic installation of control surfaces DO NOT check this b
42. the transport s loop function on off The button illuminates when the loop function is active Quick Punch Touch this button to toggle the quick punch function on off which allows for real time punching in the Pro Tools software The button illuminates when the quick punch function is active Edit Keys Popup Window Touch the Edit button to display the edit popover The edit keys popup provides many different functions and includes the following groups of controls I O Controls Input Touch this button to temporarily have the channel displays to show the currently assigned hardware input feeding each channel Output Touch this button to temporarily have the channel displays to show the currently assigned hardware output fed by each channel Assign Touch this button to use each channel s rotary control to assign an input or output to the appropriate channel Group Controls Status Touch this button to show the group status for each channel in its channel display 12 V Control 1 2 User s Guide Create Touch this button to create a group from any currently selected channels Memory Locations 1 8 Touch any of the buttons 1 8 to quickly navigate to the respective memory location Create Touch the create button in conjunction with one of the 8 buttons to create a new memory location from the current play head position and assign it to that number Window Edit Touch this button to switch the Pro Tools main inter
43. these 5 buttons to switch the V pots to auxiliary send controls for sends A E Flip Touch this button to reverse the functionality of the channel faders and the rotary encoders allowing you to adjust aux sends using the faders When flip mode is active the channel mute button acts as a send mute Surround Pan Touch this button to toggle on off the Surround Panner popup window See the section titled Surround Panner Popup Window for further details Window Touch this button to toggle the Pro Tools interface on the computer between its two main interface screens Edit and Mix Record Touch this button to put all channels into record arm mode Auto Input Touch this button to toggle Pro Tools in an out of auto input mode Group Suspend Touch this button to suspend all track groups that have been created Touching the button again will resume the normal grouping function Auto Suspend Touch this button to suspend all automation that has been written to the session Touch the button again to switch the automation back on Edit Touch this button to toggle the V control edit popup window on off See the section titled Edit Keys Popup Window for further details Keypad Touch this button to toggle the V control keypad popup window on off See the section titled Keypad Popup Window for further details Mark In Touch this button to set a mark in point at the current location of the playback head Mark Out Touch this b
44. transport of the current session Play Touch this button to start playback of the current session Pause Touch thus button to pause playback of the session Touch it again to un pause the playback Record Touch this button to punch in to record in the current session Touch the play button to punch out of record Transport Popup Window The buttons in the transport popup window work as follows Auto Punch Touch this button to turn on Logic s auto punch feature which will automatically punch the transport in and out of record based on the auto punch in and auto punch out points Touch the button again to turn auto punch back off Bars Touch this button to switch the counter display to show bars beats SMPTE Touch this button to switch the counter display to show SMPTE values displayed in hours minutes seconds and frames Edit Keys Popup Window The buttons in the Edit Keys Popup window work as follows Automation Write Section This section allows the user to filter automation status for various channel parameters Volume Touch this button to toggle all volume automation on off in the current session Pan Touch this button to toggle all panning automation on off in the current session Mute Touch this button to toggle all mute automation on off in the current session Send Volume Touch this button to toggle all aux sends volume automation on off in the current session Plug In Touch this button to toggle al
45. unt e Enter a number and then press Move Forward to move the current location forward by that amount Delete Last Char Clear Touch this button to delete the current marker in the logic session Set Position Enter Touch this button after first pressing O go to marker then a value of 1 9 By pressing enter they complete the marker selection sequence and the play head switches to the entered marker location 0 The numerical 0 key acts as a go to marker command thus pressing this button primes the keypad for entry of a value between 1 and 9 By pressing the go to marker button then a value of 1 9 and finally the enter button the user can quickly navigate to any of the first nine marker locations V Control 1 2 User s Guide 29 Channel Popup Window This popup window appears when the user presses the diamond shaped symbol located on the channel strip It allows adjustment of various channel functions including e Channel EQ e Channel Sends e Channel I O Routing e Channel Inserts The popup window contains the following controls that work as follows EQ button Touch this button to adjust the 4 band stock Cubase Nuendo channel EQ Sends Button Touch this button to adjust the channel sends Routing Button Touch this button to select the audio input sources and audio output destinations for the selected channel on your audio interface Insert Button Touch this button to insert effects on the select
46. ute the channel Solo S Touch the solo button to solo the channel Press it again to turn un solo the channel Record R Touch the record button to record arm the channel Press it again to record safe the channel 22 V Control 1 2 User s Guide Fader Touch the fader and drag it up and down to adjust the signal level of the channel Since the iPad uses a multi touch interface multiple faders can be adjusted at once just like on a real hardware mixer Level Meter The channel strip contains a detailed level meter display that displays the signal level of the channel s audio Bank Increment Decrement Using two fingers swipe the surface in the fader area but not in the area of a fader cap in a left or right motion Each swipe will bank left or right eight channels at a time Channel Increment Decrement Using one finger touch the surface in the fader area but not in the area of a fader cap and drag in a left or right motion Each swipe will bank left or right one channel at a time Keep your finger down and keep dragging to increment more than one channel Automation Arm Displayed as an R or W Touch this control to arm disarm automation for the channel whether it is currently set to read or write mode Insert Bypass Touch this control to bypass the inserts of the relevant channel The button will illuminate when the channel inserts are bypassed Channel Popup Window Touch this button to bring a popup windo
47. utton to set a mark out point at the current location of the playback head Save Touch this button to save the current session Undo Touch this button to undo the last performed action of the session 10 V Control 1 2 User s Guide Escape Touch this key to cancel out any onscreen dialog similar to pressing the escape key on a computer keyboard Bottom of Screen Controls The buttons on the bottom of the screen offer various transport related controls as the settings page button and the modifier keys popup window The controls work as follows Modifiers Touch this button to toggle the modifiers key popup window on off See the section titled Modifiers Popup Window for further details Settings Touch this button to bring up the settings screen Touch the button again to return to the main interface Banking Popup Window Touch this button to bring up the banking popup window which contains 4 buttons that allow banking the displayed channels left or right either 1 or 8 channels at a time These buttons serve as an alternate interface for bank channel increment decrement for users who prefer this method over the one finger two finger swiping method described above Time counter This display reflects the ongoing session time counter from Pro Tools It can display the session counter as SMPTE minutes seconds or bars and beats as selected in the Pro Tools session Big Counter Display Touch the left area of the count
48. w that allows editing of various channel functions including e Channel EQ e Channel Sends e Channel I O Routing e Channel Inserts Touch the button again to close the window For more information refer to the section titled Channel Popup Window Sends Bypass Sends Pre Post Button This dual purpose button covers one of two functions at any given time depending on the state of the Pre Post button located on the right hand side of the V Control interface e Sends Bypass In this mode touch the button to bypass the sends for the currently selected channel and aux send The button will illuminate when the selected is bypassed Touch the button again to stop bypassing the send Note that this icon is not present if the level controls are currently set to control panning V Control 1 2 User s Guide 23 e Pre Post Button In this mode touch the button to toggle the currently selected aux send to pre fader or post fader status The button illuminates an orange color when the aux is configured as pre fader Input Monitor Speaker Icon Touch the small speaker icon at the bottom of the channel strip to turn on input monitoring for the channel Touch it again to turn the input monitoring off The button illuminates when input monitoring is turned on Record Press the record button to record arm the channel Press it again to record safe the channel Right Hand Side Controls The buttons on the right hand side of the iPad sc
Download Pdf Manuals
Related Search