Z-Wave Wireless Water & Freeze Alarm: Instruction
Contents
1. gt Cop by DynaQuip a Automatic Water Shut Off Systems Z Wave Wireless Water amp Freeze Alarm Instruction Manual Thank you for purchasing the ZWCFS1 Z Wave enabled Wireless Water amp Freeze Alarm Leaking pipes corroded water heaters fixtures in bathrooms and laundry rooms automatic water and ice dispensers etc can all cause water damage The ZWCFS1 is a Z Wave enabled device and will send a water leak alert on any Z Wave enabled network ZWCFS1 sensors are most effective at water damage prevention when properly used with a WaterCop Z wave automatic shut off valve sold separately However a ZWCFS1 unit that is not in a Z Wave network will still alert you to water leaks using the audio alarm Specifications Inclusion in adding to a network 1 Set up the inclusion mode at the controller 2 Press and hold the button for approx 2 seconds until the ae controller indicates the unit has been included in the network Also a Power One 3 6V 1 2AA 1200mAh Lithium Battery ER14250J LS14250 or equivalent Battery Life Calculated to be 1 to 2 years with no alarms and default Z Wave network settings Frequency Range 908 42MHz US Distance Range Max 100ft line of sight in unobstructed environment Product Size LxWxD 2 4 x 1 6 x 0 8 Product Weight 0 2 Ib Operating Temperature 10 C 14F to 70 C 158F Reported Temperature Reported temperature is at the unit and has a2. 2 C accuracy System Requirement Any Z Wave enabled network and controller Testing the ZWCFS1 Moisten a paper towel and place over both of the small metal pads on the back of the water sensor until you hear the audible alarm sound The water alarm may take up to 4 or 5 seconds before it sounds If the alarm fails to sound your battery may be old or dead or incorrectly installed the sensor may not be moist enough or the water sensor may be damaged If you do hear the audible alarm remove the moistened paper towel dry the small metal pads of any water residue and hold the button for 2 seconds to clear the alarm You can then add your water alarm to any Z Wave enabled network and controller Using the ZWCFS1 ina Z Wave Network The button in the rear casing is used for including or excluding the ZWCFS1 in a Z Wave network Refer to your controller s User Manual for specific details on network inclusion exclusion and association sra OWY Products that speak Z Wave work together better FCC ID XCT WWA01 IC 8156A WWA01 908 MHz Program Madein USA Press this button Switch www dynaquip com DynaQuip Controls 10 Harris Industrial Park e St Clair MO 63077 Tel 800 545 3636 Fax 636 629 5528 www watercop com beep will be heard when the inclusion completes Inclusion and exclusion are always done at normal transmit power mode Exclusion from Removing from a network 1 Set up t
3. When the freeze alarm is cleared due to temperature rise one additional reports with status no alarm is sent During an alarm If water is detected at the monitoring location the unit will sound an 82 decibel audible alarm and will send an alert message to the Z Wave network if included in the network already Pressing and holding the button for 2 seconds will clear the Water Alarm If freezing conditions are detected no audible alarm will sound but an alert message is sent to the Z Wave network if included in the network Depending on your Z Wave controller it is possible to receive a remote alert For example with some gateway controllers you can receive an email or cell phone text message when an alarm is activated With a gateway s remote access and depending on your specific controller s capabilities you will be able to check the status of any ZWCFS1 in your network SHACK Products that speak Z Wave work together better Made in the USA Choosing a mounting location The ZWCEFS1 is suitable for use in dry interior locations only Avoid placing the ZWCFS1 close to a metal frame or other metal enclosures that may affect RF range Also avoid areas with rapid temperature swings Place the unit so that any leaks that may occur will not drip directly on the unit Recommended ZWCFS1 uses under sink next to sump pumps water heaters laundry room bathroom floor storage area gar
4. LUSIVE REMEDY AGAINST THE SELLER This warranty gives you specific legal rights and you may also have other rights which may vary from state to state No increase or alteration written or verbal to this warranty is authorized DynaQuip Controls Corporation reserves the right to change or improve the design of any DynaQuip Controls manufactured product without assuming any obligations to modify product previously manufactured or sold sra ONY Products that speak Z Wave work together better Made in the USA PN 192341
5. abor charges delays vandalism negligence fouling caused by foreign material damage from adverse water conditions chemicals weather or any other circumstances over which DynaQuip Controls has no control DYNAQUIP CONTROLS MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED EXCEPT AS PROVIDED BY THIS LIMITED WARRANTY The seller does not represent that the product will prevent any property loss by sudden or accidental discharge of water from plumbing systems into living area of a residential dwelling may not be compromised or circumvented or that the product will in all cases provide adequate warning or protection Buyer understands that a properly installed and maintained automatic water shut off system may only reduce the risk of a sudden and accidental water loss event resulting in significant water damage and is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO TURN OFF WATER SUPPLY OR GIVE WARNING OFA POTENTIAL WATER LOSS EVENT HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXC
6. age utility sink vacation recreation homes boats etc Low Battery The ZWCFS1 will broadcast an alert on the Z Wave network at regular intervals when it detects a low battery condition In addition it will periodically sound an audible chirp Your controller may be able to be configured to monitor the ZWCFS1 wake up notifications If these stop then this might be an indication that the battery has died or that transmissions from the ZWCFS1 are no longer being received Because the audible water alarm draws a large current from the battery the battery should be replaced each time an actual water leak has been detected After a water leak please ensure that there is no moisture in the unit before replacing the battery Do not install batteries that appear damaged or unsealed When replacing batteries the water seal may be broken around the screws After screwing the parts back together it is recommended to use some sealant such as silicone caulk around the screws FCC Compliance Statement Statements This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation FCC Warning Part 15 21 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate
7. eration is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Limited Warranty DynaQuip Controls Corporation 10 Harris Industrial Park Saint Clair Missouri 63077 warrants its WaterCop electric valve actuator and electronic sensor and electronic system control components against defects in material and workmanship for a period of two 2 years from the date of original shipment DynaQuip Controls warrants its WaterCop brass ball valve mechanical component against defects in material and workmanship for the life of the component In the event that such defects appear within the warranty period DynaQuip Controls will at its option and upon written notification thereof and substantiation that the product s have been stored installed maintained and operated in accordance with DynaQuip s recommendations and standard industry practice repair or replace the product without charge This warranty shall be invalidated by any abuse misuse misapplication improper installation modification or disassembly at any place other than the point of original manufacture This shall constitute the exclusive remedy for breach of warranty and DynaQuip Controls shall not be responsible for any incidental or consequential damages including without limitation damages or other costs resulting from l
8. he exclusion mode at the controller 2 Press and hold the button for approx 2 seconds until the controller indicates the unit has been removed from the network A beep will also be heard when the exclusion completes Awake Mode To remain awake and listen for commands when in a network press and hold the button for at least 2 seconds The ZWCFS1 will stay awake for approx 30 seconds Association Once in a network a controller can be used to associate the ZWCFS1 with other devices in the Z Wave network such as a light or another remote audible alarm Refer to your controller s documentation on how to associate the ZWCFS1 to another device in your network The ZWCFS1 supports two association groups A maximum of 5 associated devices are allowed in each group The ZWCFS1 sends the Basic Set Command to the associated nodes assigned to Group 1 to convey that a water Alarm is active If no nodes are assigned to Group 1 then a Binary Sensor Report value OxFF is broadcast The reports are sent at regular intervals while the water alarm is active When the water alarm is cleared via the button one additional report with status no alarm is sent The ZWCFS1 sends the Basic Set Command to the associated nodes assigned to Group 2 to convey that a Freeze Alarm is active If no nodes are assigned to Group 2 then a Binary Sensor Report value OxFF is broadcast The reports are sent at regular intervals while the freeze alarm is active
9. the equipment FCC Interference Statement Part 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications No guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help DynaQuip Controls 10 Harris Industrial Park St Clair MO 63077 Tel 800 545 3636 Fax 636 629 5528 www watercop com Industry Canada Statement per Section 4 0 of RSP 100 The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met Section 7 1 5 of RSS GEN Op
Download Pdf Manuals
Related Search