Radio Controlled Quadcopter
Contents
1. 1S LiPo Charger DIDE1512 Transmitter DIDZ1501 Micro Card Reader DIDE1507 LIPO 1S 3 7V 390MAH2. KODO Re link the quadcopter and radio 2 Make sure that the battery on the KODO is fully charged PROBLEM Red radio LED light flashing after linking SOLUTION Replace with new AAA batteries PROBLEM KODO will not stay level SOLUTION 1 Place the quadcopter on a level surface and restart the quad by unplugging and plugging in the battery 2 Check the props and motors for damage PROBLEM Unable to Flip but the KODO is flying SOLUTION Battery voltage is low and needs to be charged PROBLEM Will not take off SOLUTION 1 Check the rotor blades for proper installation 2 Battery is not fully charged 3 Check motors and props for damage PROBLEM Quadcopter is shaking SOLUTION Check the canopy chassis motors and rotor blades for damage BLADE REPLACEMENT A B A B FRONT White Blades Blue LEDs NOTE Rotor blades must be installed as shown REAR Black Blades Red LEDs 4 4 10 10 10 11 5 2 9 9 7 8 6 6 7 8 6 6 1 4 4 10 10 10 7 7 3 3 3 12 3 1 DIDE1500 Upper Shell Black Yellow 2 DIDE1501 Battery Tray 3 DIDE1502 Prop Set Black White 4 4 DIDE1503 Prop Guard Set 4 5 DIDE1504 Lower Shell 6 DIDE1505 Motor Holder 4 7 DIDE1506 Motor Cover 4 8 DIDE1508 Motor CW L F R R 2 9 DIDE1509 Motor CCW R F L R 2 10 DIDE1510 Screw Set 11 DIDM1500 Flight Control Board w Arms 12 DIDZ1500 Camera DIDE1511 USB
3. Radio Controlled Quadcopter Radio 2G Memory Card USB Card Reader Rotor Blade Guards AAA Batteries 2 USB Charge Cord Spare Blades 2 black 2 white Flight Battery KODO Quadcopter CHARGING THE FLIGHT BATTERY NEVER leave the battery unattended while charging DO NOT allow the USB port to power down while the charger is connected to the battery ALWAYS unplug the charger from the USB port and the battery when charging is complete Plug the charger into a USB to AC adapter or USB port on a computer as shown and connect the battery The red LED will flash slowly while charging and be steady when the charge is complete RADIO SETUP PROP GUARD INSTALLATION Remove the screw on the battery compartment cover Take the cover off and insert 2 AAA batteries 1 Carefully pry off the prop using a screwdriver NOTE Do one corner at a time so you don t accidentally mix up the props 2 Push the prop guard in place 3 Push the prop onto the motor so it is tight on the shaft To protect the propellers from crash damage attach the prop guards before flight RADIO For Mode 1 operation slide the mode switch to the MD1 position and hold the controller with the throttle on the right side For Mode 2 operation slide the mode switch to the MD2 position and hold the controller with the throttle on the left side LOW BATTERY INDICATOR The LEDs on the KODO will flash when the battery v
4. oltage is low and the model should land as soon as possible to avoid damaging the battery Always unplug the battery after flight The battery needs to be charged before the quadcopter is stored MOTOR REPLACEMENT The motors are not hard to replace but a soldering iron will be required to remove and replace the wires 1 Remove the propeller from the motor 2 Remove the motor cover from the bottom of the motor holder 3 While holding any two of the clamping arms away from the motor press the motor shaft down on the workbench until the remaining clamp comes loose so the motor can be removed from the holder 4 Unsolder the wires from the frame and remove the motor from the holder 5 Verify that the wires on the new motor are the same color 6 Push the new motor down in the holder until the clamping arms are back in position over the end of the motor 7 Solder the wires to the frame The wire on the right side of the frame should always be blue or white 8 Install the motor cover and replace the propeller if it is undamaged PREPARING TO FLY Your KODO is fitted with a Power On failsafe This is designed to ensure that the motors will not start until the KODO has detected the controller Important When you are finished with your flight immediately UNPLUG the battery 2 1 3 4 1 Move the throttle stick to the lowest position Power on the controller Mode 2 shown 2 Place the KODO on a level surface and connect the ba
5. ttery Do not move the KODO until you hear two beeps and the LEDs have stopped flashing 3 Advance the throttle to the highest position The controller will beep once 4 Move the throttle back the lowest position The controller will beep once The KODO is now ready to fly CAMERA OPERATION Please disconnect the battery before the memory card is inserted or removed from the camera When KODO is linked with the controller and the card is installed correctly there will be a steady blue LED just above the card A red LED flashing next to the blue LED when the camera is not operating indicates that the card is missing or not installed correctly To record a video press the V button The red LED next to the blue LED above the card will flash slowly to indicate that the camera is recording Press the V button again to stop the recording and store the video on the card If the KODO battery is unplugged while the camera is recording the video will not be saved onto the card To capture a photo press the P button The red LED on the quadwill flash once to indicate that a photo has been captured and stored The camera will not capture a photo while it is recording a video MEMORY CARD PUSH dromida com DIDE0005 v1 0 MNL 2014 DROMIDA A HOBBICO COMPANY TROUBLESHOOTING REPLACEMENT PARTS PROBLEM The quadcopter will not respond to the radio SOLUTION 1 Turn off the radio and disconnect the battery for the
Download Pdf Manuals
Related Search