User Manual User Manual
Contents
1. Phone Settings Neat Settings Switch Settings Setting Low Battery Neat Code Input Disconnected Neat Code Neat Radio Single Ind Resend Delay Neat Report Ack Neat Auto Resend Neat Walk Test TO O None CJ Record Neat Acknowledgement Sound O TTS _ File Low Battery Neat Code Type text for TTS here IR Repeat Settings Dedicated Alarm Settings Description The Neat code to send as a low battery alarm Zero no alarm sent OxFFFF uses default ID The Neat code to send as an input disconnect alarm Zero no alarm sent OxFFFF uses default ID Controls Neat radio RF Ack functionality Single transmissions stop on RF Ack Multi RF Ack is ignored Set the minimum time between repeat transmissions of the same alarm code If non zero the Neat radio will listen for and report any alarm acknowledgement The value set is the maximum time to listen in minutes Sets the time in minutes after which an alarm is re sent if no alarm acknowledge is received NOTE NeatReportAck should also be set otherwise alarms will always repeat Timeout for the Neat radio walk test if not cancelled in minutes Specifies the sound file played when a Neat alarm acknowledge is received If None a beep is played instead Set the NEAT alarm code that will be transmitted when the FreeWay battery reaches low charge e Assigning 0000 will disable the alarm e Assigning FFFF will use the default alarm ID Input Disconnected2. 1001 y W Speak v Select Sound y W PhoneBook v Select Contacts 4 If we wanted to change our list so the phonebook contact is dialled before the speak action we can either select the speak actions positional arrow down or the phonebook actions positional arrow up Y NeaTcode Y Speak v Select Sound W PhoneBook v Select Contacts This would then result in the required list of actions as shown below Il NEATCode W PhoneBook v Select Contacts W Speak v Select Sound Page 46 Finish san Client Detais gt Global Settings TDI Send To Freeway This option is enabled only if a newFreeway is plugged into the computer via the USB cable and switched on Selecting this button will transfer the current setup to the device A progress bar will become visible to monitor transfer progress Print Overlay This option will bring up a print preview of the layout in its current state From there you can print the overlay using the windows print screen If you want to make changes to the layout quit the preview and modify the setup in the Cell Settings tab Greate Backup This option allows you to save your current setup to a file for storage To open this file choose the Load From Drive option from the Start tab
3. received alternatively in order to operate correctly Primary and Secondary codes accommodate situations where two codes are required Note When capturing the secondary code ensure the button press is directly after capturing the primary code This will reduce the risk of capturing identical infra red codes behind both primary and secondary positions If the secondary code is left blank it will be ignored and the primary code will be transmitted on every cell action New Function In some cases infra red functions will need to be added yy lt Once an Appliance Type Manufacturer and Model has been chosen its list of functions will appear below If a new function is required click New Function as shown below Upon selecting New Function a Name filed will appear as shown below A New Function Name Enter the new functions name and you will notice that the Add option becomes accessible A New Function Select Add and the new function will be added to the currently selected devices list of functions Page 41 Transmit NEAT Alarm In order to assign a simple NEAT radio frequency transmission to a cell place the required four digit number in the box provided as shown below Transmit NEAT Alarm 1001 Upon cell selection the NEAT code will be transmitted Note Only number 0 9 and letters A F are accepted Dial a Number In order to assign a simple dial telephone num
4. t O File till Both Audio Scan Prompt and Audio Selection Prompt have their own test button After recording selecting or entering TTS text the prompt can be tested via select the required test button Page 16 Switch Settings Start A Client Details Global Settings Page Settings Cell Settings gt Finish Phone Settings Neat Settings Switch Settings Scan Settings IR Repeat Settings Dedicated Alarm Settings E Wired Input 1 Mb Wired Input 2 ESE Y Wired Input 2 Internal Capacitive Input EA gt Capacitive Switch Remote Input 1 EE HAM Channel For Remote Switch 1 P Remote Input 1 2 Li Remote Input 2 ESTE Remote Input 2 The Freeway is operated via a number of inputs These inputs are configured in a default order but can be changed to accommodate different situations or user needs Wired Input 1 Wired input 1 switch mode options e Don t Use e Switch Input 1 e Switch Input 2 e Dedicated Alarm Wired Input 2 Wired input 2 switch mode options Don t Use Switch Input 1 Switch Input 2 Dedicated Alarm Internal Capacitive Input Internal capacitive input mode options e Don t Use e Switch Input 1 e Switch Input 2 e Dedicated Alarm Remote Input 1 Remote input switch 1 set to channel 1 options e Don t Use e Switch Input 1 e Switch Input 2 e Dedicated Alarm Channel For Remote Switch 1 Remote switch 1 channel options e 0 Channel 0 e 1 Channel1 e 2
5. Channel 2 e 3 Channel 3 e 4 Disabled Remote Input 2 Remote input switch 2 set to channel 2 options e Don t Use e Switch Input 1 e Switch Input 2 e Dedicated Alarm Channel For Remote Switch 2 Remote switch 1 channel options e 0 Channel 0 e 1 Channel1 e 2 Channel 2 e 3 Channel 3 e 4 Disabled Page 17 Page 18 Scan Settings Client Details Global Settings Page Settings Cell Settings Phone Settings Neat Settings Switch Settings Scan Settings IR Repeat Settings Dedicated Alarm Settings Setting Description Contains the file holding the default sound used when no square specific sound is Default Sound specified If zero no default sound is used gt Percentage increase in scan time for repeated scans cycles Scan Cycle Siow Down 0 means no increase in scan time 20 20 longer on each subsequent pass For turbo scan mode age of scan period for the turbo pass Tarbo Speadup 100 no speed up 80 delay is 80 of standard Turbo Announce If nonzero announce during forward pass of turbo scan Max Cycles If no press maximum number of scan cycles Dim Cell Level The relative brightness of a dimmed cell 0 100 of full brightness Press Debounce Internal and external switch press debounce delay 0 025 Seconds Dedicated Alarm Debounc Press debounce for dedicated alarm input Period for manual scan select press LONG PRESS coma asserts tees as multiple of de
6. Freeway to adjust the brightness using its full range Setting the value to O will disable Auto Brightness Change Page 29 Cell Settings The Cell Settings area is where cells within your layout are configured Cell Settings Select Layout Select layout Within the Select Layout area situated on the left your pre configured layout will be displayed as shown below in this case a 2x2 cell layout In order to select a cell from within the layout for editing simply select the cell amp it will be highlighted as shown below Once a cell has been selected it can be configured within the Edit Cell area Page 30 Cell Settings Edit Cell Edit Cell After selecting a cell for editing from the Select Layout area situated on the left its available Edit Cell options will become available Appearance Background colour image text and prompt configurable cell options are available The text formatting toolbar provides a number of text formatting icons B Makes selected text and numbers bold AX Reduces selected text and numbers font size Makes selected text and numbers italic Aligns to the left with a ragged right margin U Underlines selected text and numbers Centres the selected text and numbers abc Toggles selected text uppercase lowercase Aligns to the right with a ragged left margin H Al Increase selected text and numbers font size es Changes col
7. IN No Rows To increase the number of rows slide the pointer upwards To reduce the number of rows slide the pointer downwards As the pointer is moved rows will appear or be removed accordingly No Cols To increase the number of columns slide the pointer to the right position To reduce the number of columns slide the pointer to the left position As the pointer is moved columns will appear or be removed accordingly Note Cells that are already populated when hidden can be recovered if the editor does not move away from the Page Settings area Once the editor has moved away from this tab any cells that were hidden will be permanently lost Page 25 Below we can see a Freeway layout with the maximum number of cells available along with their sequential ordering Page Settings Scan Settings Scan Settings Customize the user s preferred method of input control scanning mode and auditory prompt Select the box positioned next to the required option to enable it Page 26 Selection Method How the switch will be used to initiate scanning and select cells Momentary Press and release the switch to start scanning Press and release the switch whilst scanning to select a cell Held Press and hold the switch to start scanning Release switch whilst scanning to select a cell Manual Press to start scanning Short press will scan to the next cell Long press will select the current ce
8. volume may be required to be set at a higher level so can be heard clearly but in evening times volume may be required to be reduced as a result of reduced background noise Dwell Time milliseconds Set the dwell time for the relevant day and night setting Dwell time determines the period of time each cell is dwelled upon until it moves to the next cell in the scanning cycle in effect this is the scanning speed Lower values will result in shorter dwell times resulting in a faster scanning cycle Higher values will result in longer dwell times resulting in a slower scanning cycle Tremble Tremble determines how long the switch needs to be held down before the appropriate action is triggered Values are groups of 10 milliseconds for example 2 20 milliseconds Sleep Timeout minutes Set the period of time to elapse in minutes of user inactivity before the unit falls to sleep Brightness Set the default Freeway brightness level For example in light daytime environments a high level of brightness may be required to optimize scanning visibility In evening low light environments a lower level of brightness may be required Values range from 0 15 0 lowest 15 highest Auto Brightness Change Freeway s on board ambient light sensor can adjust the level of brightness automatically Auto Brightness Change allows control over the level of automated change in brightness Setting the value to 4 will allow
9. A AA AAA A AA AAA Ac 25 a aasa sect cci cd noes ea A a 26 SAMMI 1 OCS a NA 26 PCI PLOMO ras A o a7 Sy ana n a A E E E 27 MAIS I AN AA 29 A A EEA E A T E E EE E T E A A T A T oun 29 a AE A A A A E E A 30 PO DCAPANICE erica A AAA ANN AAN 30 o A A E AA A NE E 35 a E A E AA PO APO AN A EAN A tte A N N A E PEN A A O N 36 S E S gon EE OAE AE OON E EAA AN 36 ESCOCIA A N A I ere anes eee 40 Arranca ARONS psa cal 42 tania 46 A 46 Ae ao AI A Co O o O T S T E N EN 46 ESO ns 30 bees Oe en nese E E ene A ame Wan E em ONTOS ONE ETE A See eon A E eee O 46 Page 4 Getting to know your freeway Volume control 2 Scan speed control 3 Manual brightness control auto function also available 4 Anti tremor sensitivity also adjustment 5 On Off switch 6 3 5mm input socket 7 Mains power charger socket HC501C 8 USB input for PC programming 9 Integrated touch switch External Buttons 1 Volume Control Adjust the volume of the Freeway to your desired level using the increase volume and decrease volume buttons 2 Scan Speed Control A Adjust the scanning speed of the Freeway to your desired level using the increase speed and decrease speed buttons 3 Manual Brightness Control x Adjust the brightness of the Freeway to your desired level using the raise brightness and reduce brightness buttons e Pressing both and simultaneously will toggle between enable disable
10. Neat Code Set the NEAT alarm code that will be transmitted on input disconnection e Assigning 0000 will disable the alarm e Assigning FFFF will use the default alarm ID Neat Radio Signal Ind Configure NEAT radio frequency acknowledgement functionality e Single Transmission stops on radio frequency acknowledgement e Multi Radio frequency acknowledgement is ignored NEAT No Resend Delay Set the minimum time period between repeat transmissions for the same alarm Move the slider in a horizontal direction until the required value is displayed Page 15 NEAT Report Ack The NEAT radio will listen for and report any alarm acknowledgement The value entered is the time in minutes to listen e O Disabled NEAT Auto Resend The time in minutes after which an alarm is re sent if no acknowledgement is received NEAT Report Ack needs to be enabled otherwise alarms will always repeat NEAT Walk Test TO Timeout period for the NEAT radio walk test Set the time in minutes NEAT Acknowledgement Sound Specifies the sound played when a NEAT alarm acknowledgement is received If no audio prompt is required then select None _ None Record amp assign audio to scanning prompt and or the selection prompt Record Assign TTS Text To Speech to scanning prompt and or the selection prompt TTS Type text for TTS here Select from file allows you to select an audio file from your local drive
11. Page l FREEWAY liveyourway User Manual Version 1 0 Page 2 Table of Contents Gertie TO how YOU Freeway rss need 4 Ey isaac A A 4 Mo An A A 4 We Gare o ea Eee en ee PU re ree Ser rer FP O un rs Sera arene er 4 aR eg el Beg edn ach Slo plus emer ce emer qP ner aera terrane eee toy ence ane eee me ee ee ae te eee 4 Ec sn PE O 5 EOI SEA toca E N 5 Ed lao E O A 0 E E E RPG OU A 5 ds e ASIA AA 5 Eds a o en tee recent 5 Sie Ta tSd TOMES session 5 A EE A AEN E A AA E O A T 6 Bec choro ane I TE A E E N E N S 7 Ph o A ne seca ne E PRO CO O PERO EEE AAEE E ATE 7 SEMA A aan 7 2 AAA AA 8 Bice a py Sn ooo 8 STIG PINS on a ii li 8 CONT SU TaCIOH NOTES sc NAAA ti 9 PREVIOUS AMO E AN AAA AA AAN AAA ARA 9 A A A E ETE 9 GOA Ea PRO O O U 0N0PeP PPPPPPS PP O EME POE RA 10 NS AUN pe ee ers Nene meyer rer ey eter ern errr Error Bookmark not defined OGD See PRONE an praia Error Bookmark not defined Pror TOP SIS IWBncsan ii ibn Error Bookmark not defined Ss 1 eee rT enemy One oe ine eer Error Bookmark not defined or a serene tes ono ne Meera nr Pere rarer etree Seem rey eee rere rere eee ee E rem i Tne ce ors 12 Glo al EEEE ENEE EI N ENEE N EAN S ET NEM Ce Are ena hee Sareea isn eee EY SEIN AIAI en near aan ae T reer ee 12 Posun VOS RECON varian AA AA 19 AMECA ARO A AAA A 21 FAS SSE iran 24 SEE LAO 24 A ucae sp1csacawsnaneeesnnrseiai picasa eon A E ail eect anne 24 A A o REE 5 gn RO un IN 24 CU A AA
12. assigned to individual phonebook contacts The default telephone can be selected along with an outside line prefix if required Default Phone Clicking on the current entry will result in a drop down list of available options to choose from RTT No Phone Sero Chi 6 Sero Chi 7 Sero Chi 8 Freedom Gewa HC2003 Page 11 Prefix for outside line In situations when a digit or series or digits needs to be dialled in order to obtain an outside line before dialling a phonebook contact Prefix for outside line Enter the required digits s into the box required as shown above Create Phone Book Contacts Selected Contact Details w Possum Ltd 01296461000 Name Possum Ltd Number 01296461000 Audio Scan Prompt a None Record a TTS Possum _ File Audio Selection Prompt C None O Pecora 0 TTS Possum _ File Add Contact Delete All Contacts are displayed in the phonebook contacts list situated on the left When a contact is selected from within the phonebook list its details are then displayed in the selected contact details on the right As contacts are added to the phonebook list a scroll bar will appear to facilitate easy contacts browsing Page 12 Add Contact Add Contact After selecting Add Contact a new contact will appear within the list as shown below Contacts Selected Contact Details Il Possum Ltd 01296461000 Name New Contact W New Contact Number A
13. ay Text Image Location a LJaU ALARM Text Image Location Freeway Text Image Location a my O Freeway Page 35 Cell Prompt Record select and assign a sound file for the currently selected cell s audio prompt a None Record a TTS Type text for TTS here File da Record D reor a Selecting Record Prompt will initiate the Possum Voice Recorder After recording an audio prompt for the cell the length of the sound clip will be displayed and the Test button will become accessible Record 2 1 seconds To playback the recorded audio select Test TTS Text To Speech Select TTS and type the required word s in the box provided TTS Hello To test the text entered select Test and the typed message will be spoken File Import Local File In cases where audio prompts files already exist these local files can be selected and assigned via the Freeway file browser Select File to select a sound file from your local drive Fite 7 Note Freeway currently supports sound files of type wav only Upon selection the Freeway file browser window will open allowing navigation to and selection of an audio file of your choosing Page 36 fiction Each cell is capable of performing a number of simple or advanced actions if required Actions are split between three sections e No Action Required e Simple e Advance
14. ber action to a cell place the required telephone number in the box provided as shown below Dial A Number 01296461000 Upon cell selection the telephone number will be dialled Play a Sound A sound can be assigned to play upon cell selection Play a Sound a None Record Ts Type text for TTS File b If no sound is required then select None as shown above To Record a sound or select a File please see earlier section Record Prompt TTS Text To Speech Select TTS and type the required word s in the box provided To test the text entered select Test and the typed message will be spoken Page 42 Advanced fictions Select this option if you wish to configure advanced cell actions Available Actions Phone Book Play Voice Sound Transmit IR z gt Dial a Number Toggle Day Night Mode The Available Actions window shown above allows the editor to build a list of actions within a custom order and assign them to a single cell Phone Book Select a contact from the phonebook to dial W PhoneBook v Select Contacts Select the circle with the expand symbol and the current phonebook contacts will be displayed Choose the required contact by placing a tick in the adjacent box as shown below W PhoneBook Select Contacts Possum Ltd The Phone Book advanced action has now been added to the list ir To remove the action sel
15. bounce period Previous Page 19 Possum Voice Recorder A Possum Voice Recorder v Recording Device O WW 00 00 000 es Recording Device v Recording Device This is the currently selected device for recording audio To check the currently selected device click the arrow down circle to expand the information a Recording Device Select a recording device Microphone USB Audio Device v L The information can be hidden again by clicking the arrow up circle Click record to start recording audio w Click stop when you have recorded the required audio When not recording the stop button will be inaccessible 00 00 000 ndicates length of current recording Reset Whilst recording select reset to clear amp begin recording again Mic level The MIC recording level can be altered by moving the slider up amp down Whilst recording your audio it will be displayed as shown below Page 20 Once your audio has been recorded you will be presented with the following Page 21 Advanced Settings Advanced System Settings Dedicated Alarm Action This is the action triggered by the dedicated input switch 3 Dedicated Input Alarm ID The action parameter used for dedicated alarm Remote Switch Ch2 Remote switch 2 channel options e 0 Channel 0 e 1 Channel1 e 2 Channel 2 e 3 Channel 3 e 4 Disabled Default Sound Specifies the sound file used for t
16. d When configuring a cell if no action is required then the corresponding option should be selected this is the default action option No Action Required Simple Actions T Simple O ss Transmit Infra red W Choose IR E Record Transmit NEAT Alarm aaa TTS Type text for TTS here Fil i Dial A Number G Ow a Play a Sound The simple actions area offers quick and direct access to a number of simple actions Note All four simple actions can be assigned to a cell at the same time Transmit infra red Select an infra red device and transmit one of its commands from the Possum Freeway infra red database Select Choose IR and the following window will be displayed Choose IR Manufacturer gt Model Function Name Primary Code Alternate Cod v New Function Transmissions Interval ms O Repeat IR A Timeout Setting J Page 37 In order to select an infra red device start with selecting the required Appliance Type Note Selection boxes will be greyed out whilst inaccessible on making a selection the next box will become accessible Once an Appliance Type has been chosen Manufacturer will become accessible click Manufacturer and select the required option from the drop down list Once a Manufacturer has been chosen Model will become accessible click Model and select the required option from the drop down lis
17. e sound that will be played when the cell is highlighted not selected None No auditory prompt is set Speech The chosen recorded prompt will be heard Beep A beep will be heard Day and Night Settings The lower section of scan settings allows manipulation of day and night settings as shown below Day Settings Volume demp Dwell Time ms 9 ud Tremble 9 uy Sleep Timeout mins E Go Brightness 9 E Auto Brightness Change LJA Night Settings Volume demr Dwell Time ms o ED Tremble EY Sleep Timeout mins dmm Brightness Vawda Auto Brightness Change LAIA Freeway has an on board ambient light sensor that depending on the environment and surroundings can determine if day or night mode is required In situations where light is poor Freeway will automatically enable Night Settings In situations where light is good Freeway will automatically enable Day Settings As a result of the Freeway s intelligence user view ability is optimized and valuable battery charge is conserved resulting in longer overall usage times Page 28 Each option can be adjusted via its corresponding paddles positioned to the left and right of the options value mmp To reduce an options value select paddle down To increase an options value select paddle up Volume Set the volume level for the relevant day and night setting For example in busy daytime environments
18. ect Delete Item WI Page 43 Play Voice Sound Assign a recorded message TTS or local sound file to play upon cell selection W Speak v Select Sound Select the circle with the expand symbol and play voice sound options will appear W Speak Select Sound None Record 11s Type text for TTS here File Please refer to previous cell prompt sections Record TTS and File To remove the action select Delete Item Transmit IR Assign an infra red device command to transmit upon cell selection W PlayiR PES Panasonic Television N2QAYB000239 Function 0 Please refer to the previous Transmit infra red section When a device and function has been chosen details of the selected device will be displayed upon returning to the available actions window as shown above To remove the action select Delete Item W NEAT Assign a NEAT code to transmit upon cell selection Il NEATCode 1001 Enter the required four digit NEAT code into the provided box as shown above Upon selecting the cell the entered NEAT code will be transmitted To remove the action select Delete Item Dial a Number Assign a telephone number to be dialled upon cell selection U DialNumber 01296461000 Enter the required telephone number into the provided box as shown above Upon selecting the cell the telephone number will be dialled To remove the action select Delete I
19. he default sound e 0 No sound file used Cycles to Extend Set the percentage of increase delay for repeat scans e 0O No increase delay e 10 10 increase on each subsequent pass e 20 20 increase on each subsequent pass e Etc Turbo Speedup Set the percentage for turbo pass scanning turbo scanning only e 100 100 of standard scanning speed no change e 80 80 of standard scanning speed e 70 70 of standard scanning speed e Etc Turbo Announce Announce during forward pass of turbo scanning Max Cycles Set the maximum number of repeated scanning cycles e 0 No repeats Page 22 Dim Cell Level Set the percentage of the relative brightness of a dimmed cell e 100 100 brightness e 20 20 brightness e Etc Press Debounce Press debounce delay for Internal and external switches This reduces the chance of multiple presses depending on user input Time is set in units of 5 milliseconds o 1 5ms e 5 25ms e Etc Dedicated Alarm Debounce Set the press debounce delay for dedicated alarm switch 3 This reduces the chance of multiple presses depending on user input 1 5ms e 5 25ms e Etc Manual Scan Press Time The period of time required for manual scan select presses long press This value will multiply the press debounce value Fast Glide To Set the timeout period for Fast Glide operations After the time period has expired the operation will halt Value is set in
20. le and accessible Tabs are positioned so when creating a new Freeway configuration they can be worked through in a sequential order from left to right start finish Although tabs are positioned in this way when importing previously saved Freeway configurations if required each tab can be directly accessed via selecting the required tab The Start screen provides the user with a number of starting choices e Load From Drive e Load From Controller e Setup Manually Page 7 load from Drive Load From Drive Selecting this option will allow you to choose a previously saved Freeway layout from your local drive Select Load from Drive amp the following window will be displayed We Ji Possum FREEWAY Freeway Configurations y Search Freeway Configurations p Organize v New folder A Name Date modified Type Ft Favorites WE Desktop 20131107 _1234_Possum_07 11 13 fw 07 11 2013 16 07 FW File Je Downloads de Dropbox E Recent Places Libraries Select a file to preview ES Documents ad Music Pictures Subversion E Videos 4 m File name 20131107_1234_Possum_07 11 13 fw v New Freeway Setup Files fw Navigate to the destination of your Freeway files amp select the appropriate file by either double left clicking the required file or single left clicking amp then selecting Open After selecting the required layout it will be loaded to your FreeWay soft
21. ll Turbo Press and release the switch to start scanning scanning speed will be fast When turbo scanning has passed the desired cell press and release the switch to pause scanning and then initiate reverse scanning at the normal scan speed When the desired cell is highlighted press and release the switch to select the cell Scanning Mode How the layout will be scanned Linear Scanning begins at the top and will move downwards until it reaches the last cell scanning will then begin from the top again If two columns exist scanning will begin in the upper left corner and move downwards Once the first column has been scanned the second column column positioned on the right will begin scanning in the lower right corner and move upwards until it reaches the last cell scanning will then begin again from the upper right corner Column Row Scanning begins with the column positioned on the left Each column is highlighted in turn Once a column has been selected cells within the selected column will be scanned individually beginning from the upper cell Quadrant Quadrant scanning moves in an anti clock wise movement beginning with the quadrant positioned in the upper left corner then the lower left corner then the lower right corner and finally the upper right corner Once a quadrant has been selected its cells are highlighted in turn starting with the upper cell and moving down Page 27 Auditory Prompt This is th
22. milliseconds Slow Glide To Set the timeout period for Slow Glide operations After the time period has expired the operation will halt Value is set in milliseconds Subsidiary To When Subsidiary To is activated and input is transferred there needs to be a method of escape timeout so control can be returned to Qwayo Set the period of time in milliseconds for user inactivity no switch operation before returning control to Qwayo Page 23 Sticky To Once a cell is triggered via operation of Qwayo switch or touch screen its action will be repeated until the user triggers the Qwayo switch or touches the screen again to cancel the sticky to operation When Sticky To is activated and the cell action begins to repeat there needs to be a method of escape timeout so the operation can be cancelled in cases where it cannot be cancelled manually Value is set in milliseconds Phone Type Selects the infrared codes used for the telephone function actions and phonebook dials e 0 No telephone e 1 HC2006 Sero Channel 6 e 2 HC2006 Sero Channel 7 e 3 HC2006 Sero Channel 8 e 4 Freedom e 5 GEWA e 6 HC2003 e 7 15 Reserved e 16 Other telephone use captured codes Page 24 Page Settings Page Settings Select layout Configure the layout of the Freeway screen by selecting the number of Rows 16 maximum and Columns 2 maximum No Cols 1 _ Ae o Bo Bo 5 6 o
23. mote control firmly and continually point at the top of the Freeway Florescent tube lights and natural sunlight can have adverse effects If capture is problematic try and eradicate these sources of interference IE cancel As instructed in the image above position your Freeway and device handset accordingly and transmit the desired infra red command Note During infra red capture the Freeway will indicate the stream of data received represented in two vertical bars In most cases only a short press is needed whilst capturing infra red and will be illustrated on the Freeway by only the lower left bar lighting Page 40 Infra red Capture In some cases infra red functions will still need to be captured As shown below each infra red function has two capture infra red options available known as Primary and Secondary codes Selecting one of the little red record buttons will prompt for capture of the chosen primary or secondary code Position the Freeway and original handset as shown in Capture Search section and transmit the required infra red code After successfully capturing the desired infra red command you will be returned to the IR Selection window where your recently captured code will be available for playback as shown below Select OK to save changes and return to Cell Settings Primary and Secondary Codes Some infra red devices require two slightly different infra red codes
24. of Auto Brightness Change Page 5 4 Anti tremor Sensitivity Control Y Adjust the anti tremor of the Freeway to your desired level using the increase sensitivity and decrease sensitivity buttons 5 On Off Switch In order to use the Freeway the unit will need to be powered set the sliding switch closest to the ON position I To switch the Freeway unit off set the sliding switch closest to the OFF position 0 6 3 5mm Input Socket If required Freeway can accommodate an external 3 5mm input switch 7 Mains Power Charger Socket Socket to accommodate the accompany HC501C mains power charger e IMPORTANT Use only the provided Possum HC501C mains power charger 8 USB Input Socket USB communication port used to connect the Freeway to a PC in order to transfer Freeway layout between Freeway and PC 9 Integrated Touch Switch The integrated touch switch when enabled can be used as a user input switch Simply touch or tap anywhere on the area to trigger switch operation Page 6 Freeway Software Start A Client Details Global Settings Page Settings Cell Settings D Finish Welcome to Freeway 3 Setup FREE WAY liveyourway Load From Drive Load From Controller Setup Manually Upon opening the Freeway software you will be presented with the Start screen as shown above The Freeway software is navigated via tabs located across the top of the software which are always visib
25. our of selected text and numbers Set Cell Text Select the text field and enter the text that you would like to appear for the currently selected cell s label Select this option to adjust the currently selected cells background colour Selected Color Opacity ScRGB sRGB SA 1 A 255 ScR 04507858 R 179 ScG 0 7083758 G 219 ScB 1 B 255 Hexadecimal Notation FFB3DBFF To change cell background colour left click and hold the hue scale colour slider shown above then move vertically in the required direction as the slider is moved it will change colour accordingly Page 31 Below we can see that the colour has been changed from pale blue shown above and red has been selected y The selected colour will then be displayed in the upper right corner as shown below Note To quickly jump to the required colour click the sliders bar on the selected area and the slider will reposition it self accordingly Once a cell background colour has been selected its colour shade can also be adjusted To change the shade of the cell background colour click the required area in the window positioned on the left as shown below To lighten the shade of colour select an area towards the upper left corner To darken the shade of colour select an area towards the lower right corner Above we can see that the red colour has been changed to a light shade of pink We can also adjust the cell background colours opaci
26. switch press This mode times out after say 30 seconds from last transmission This timeout is configurable in the Advanced Settings section of the software Transmission Interval This is the period of time between repeated transmissions Set the value in milliseconds Timeout This is the period of time set to elapse before halting a repeated infra red transmission if no user input is received e Short Refers to Fast Glide To Global Setting value e Long Refers to Slow Glide To Global Setting value When you have successfully chosen an infra red function and configured its repeat options select OK to save your changes and return to Cell Settings Page 39 Capture Search Capture Search If you cannot find a particular device within the Possum Freeway infra red database the Capture Search facility allows the user to transmit an infra red command from their desired handset and search the Possum Freeway infra red database for any possible existing matches Upon selecting Capture Search you will be prompted with the following Function name Hold the device to capture pointing at the top of the Freeway unit Within 10 seconds of initiating this process fire the IR into the Freeway The lights on the Freeway display will light up as the IR buffer is filled Once complete the Freeway will wait 3 seconds for further IR before terminating capture Ensure you press the button on the re
27. t yy lt When an Appliance Type Manufacturer and Model have been chosen the device list of functions will be displayed as shown below Appliance Type Pammsonde Function Name Primary Code Alternate Code gt v a v New Function Repeat IR lo nl Mode Transmissions Interval ms Timeout 2 EE Capture Score In order to select one of the devices functions and assign it as a simple cell action select the required function and it will highlight orange as shown below Function Name Primary Code Alternate Code 4o O DOA gt h 2 m aj Note Functions with infra red assigned will have an accessible green playback button Page 38 Repeat IR Once a device and function have been selected if required the selected transmission can be repeated In order to enable Repeat IR click the adjacent box and it will become accessible Repeat IR Mode Goa ED L timeout Repeat IR Modes Glide Sticky Subsidary The Glide option repeats the chosen infra red transmission whilst switch input is held Upon releasing switch input the transmission will halt The Sticky option repeats the chosen infra red transmission after press and release of switch input the switch must be pressed and released a second time to halt repeated transmission The Subsidary option repeats the chosen infra red transmission on each
28. te amp time of change or maybe an explanation of why the layout has been configured in a particular way Previous and Next Previous Next Selecting Previous will navigate you back to the screen you were previously on Selecting Next will navigate you to the next screen Save Selecting Save will prompt you to save the current layout The Save As window will appear you will be required to select a destination filename for the layout The filename will be automatically populated with the date followed by the customer ID then the Customer Name Page 10 Global Settings Global Settings gt Client Details Global Settings Page Settings Cell Settings gt Finish Phone Settings Neat Settings Switch Settings IR Repeat Settings Dedicated Alarm Settings Create Phone Book Contacts Selected Contact Details w Possum Ltd 01296461000 Name New Contact En Default Phone Number Audio Scan Prompt E None Prefix for outside line Lo 0 Record 0 TTS Type text for TTS here File a Audio Selection Prompt O None O reco 0 TTS Type text for TTS here _ File pel Add Contact Delete All The Global Settings area contains a host of settings for phone NEAT switch scan IR repeat and dedicated alarm configuration Phone Settings Telephone contacts can be added amended or removed from the phonebook Audio scan and selection prompts can be recorded and
29. tem Wi Page 44 Pause The pause action inserts a period of time delay before the next action is executed W Pause Co A The time value is displayed in milliseconds and will increment or decrement in multiples of 100 via the and paddles positioned either side of the value box To remove the action select Delete Item 1i Note Custom values can also be entered directly Toggle Day Night Mode Toggle between day mode and night mode preferences Il SwitchMode Toggle between Day and Night settings Upon selection will toggle the current mode preference To remove the action select Delete Item W Loop Assigning a loop will result in looping any actions that appear within the list before the loop action ily Loop A list of actions can be looped if required The loop action will always position itself at the end of the list and cannot be positioned elsewhere To remove the action select Delete Item Wt Note The list of actions can only be looped once No Action Select this option if no action is required To remove the action select Delete Item Wi Page 45 Positioning Actions within the fictions list Each action in the actions list contains positional arrows allowing the actions position within the list to be changed For example below we can three actions added to the actions list Positions that are unavailable will have their arrows greyed out as shown below T NEATCode
30. tures Freeway v Search Freewa Organize v New folder XX Favorites Pictures library HZ Desktop Freeway Je Downloads Ss J Dropbox JPEG image Recent Places 25 3 KB Arrange by Folder y A Libraries FS N AY Documents A Music t Pictures Subversion BB Videns File name Freeway jpg v Image files j pg jpeg jpe Page 33 Once an image has been chosen for the cell either via double clicking the image or selecting Open the file browser will automatically close and the cell should now display the chosen image below we can see the upper left outlined cell has a black background colour and a Freeway image file AAN Independeracr you Gin cour or Remove Image Remove Image Once an image has been assigned to a cell the Remove Image option becomes available To remove an assigned image from a cell select the cell and then select Remove Image the image will be removed promptly Note If no image has been assigned then the remove option will be greyed out inaccessible Text Image Location Choose the texts position relative to the associated image The small central orange square box represents the images position The four surrounding larger rounded boxes determine the texts position Selecting one of the four surrounding boxes will position the text and image accordingly Page 34 Please see the following examples Freew
31. ty Opacity Moving the opacity slider in a horizontal direction will change the opacity of the currently selected colour automatically Positioned directly below the opacity slider are a number of colour values Page 32 ScRGB and sRGB The ScRGB and sRGB colour space values allow a selected colour to be accurately represented this can be very useful when wanting to user the same colour scheme over a number of different cells ScRGB sRGB ScA 1 A 255 ScR 0 8307699 R 235 ScG 0 008568126 G 23 ScB 0 008568126 B 23 Hexadecimal Notation EFFE ma Cut Ctrl X Copy Ctrl C Paste Ctrl V The Hexadecimal notation is derived from both ScRGB and sRGB values As shown above the hexadecimal notation value can be highlighted and then copied right click on the value once it has been highlighted or press Ctrl c Once the value has been copied to the clipboard it can then be pasted into another cells hexadecimal notation field right click the empty field and selecting paste or press Ctrl v Note A hexadecimal notation can be pasted multiple times as long as it remains within the clipboard and is not overwritten Note All SCRGB and sRGB values can be copied and pasted Choose Image Choose Image Select this option to add an image to the chosen cell The Freeway file browser will appear allowing you to navigate to an image file that resides on your local drive as shown below fa PY Open OI Jo Libraries Pic
32. udio Scan Prompt Audio Selection Prompt 0 None E Record m TTS Type text for TTS here _ File sa Add Contact Delete All Enter the required details in the area on the right contact name and number will automatically refresh in the phonebook contacts list as the information is entered Delete All Delete All Select Delete All to remove all current phonebook entries Delete Contact To delete an individual contact from the phonebook list select the trash can position to the left of the contact entry WARNING Once a contact has been deleted it cannot be recovered Page 13 Audio Scan Prompt and Audio Selection Prompt e Audio Scan Prompt Plays assigned audio prompt when cell is scanned e Audio Selection Prompt Plays assigned audio prompt when cell is selected If no audio prompt is required then select None None Record amp assign audio to scanning prompt and or the selection prompt Q Record Assign TTS Text To Speech to scanning prompt and or the selection prompt TTS Type text for TTS here Select from file allows you to select an audio file from your local drive j t File a Both Audio Scan Prompt and Audio Selection Prompt have their own test button After recording selecting or entering TTS text the prompt can be tested via select the required test button NEAT Settings Page 14 gt Client Details Global Settings Page Settings Cell Settings gt Finish
33. ware and the Client Details screen will be displayed load from Controller Load From Controller Selecting this option will allow you to transfer the layout that currently resides on your Freeway controller to the Freeway software Please ensure that the Freeway controller is connected to your computer via the supplied USB cable before attempting to transfer layouts Note This option will only be available for selection when a FreeWay controller is connected to the computer via the supplied USB cable Setup Manually Selecting this option will allow you to manually configure a new layout without loading an existing one On selecting Setup Manually you will be navigated to Clients Details area Page 8 Client Details Client Details Global Settings Page Settings Cell Settings gt Finish Configuration Notes Customer ID Enter identification for the customer this can be in both alphabetical and or numerical format The customer ID will be used to create the default filename when saving the configuration to the local drive Customer flame Enter the customer or client s name The customer name will also be used to create the default filename when saving the configuration to the local drive Page 9 Configuration Notes Configuration Notes An area provided for notes that may be relevant to the configuration of the layout Changes to the layout could be recorded along with the da
Download Pdf Manuals
Related Search