EUKT02-RGB60 User Manual
Contents
1. ation surfaces wall colors mounting angle and objects can all affect the lighting appearance Before installing this LED lighting kit please consider the following Location of the power supply and the RGB Controller LED Lighting ON and OFF plan The layout configuration you will be using Wire connections to your LED strips de EUuUComtrols EUKT02 RGB60 Typical Configuration Options Straight LED Connection are LED Strips Controller Tn ee SS Te Array LED Connection LED Strips RGB Controller f COO Toni 2 none Loop Back LED Connection i MERE eCa RGB LED Strips Controller Center Feed LED Connection hin innit iii E LED Strips RGB Controller w EUuUComtrols EUKT02 RGB60 INSTALLATION INSTRUCTIONS RGB Remote Control Power Supply P Input Voltage 100 240VAC Output Voltage 12V DC 21 RGB Controller Miitiiil amp LED CONTROLLER CE LED Strips After you had determined the mounting position you are going to use e Make sure to clean the surface area The area should be free from oil or waxes and should be smooth and dry to ensure proper adhesion of the 3M tape on the back side of the RGB strip light e Gently remove the 3M backing and press the RGB strip light between the LED s to securely contact the surface of the mounting surface Never press on the individual LED s since this could damage their solder connect2. colors flashing 2 12 RGB flashing 13 RGB flashing 2 14 RG flashing 15 RB flashing 16 GB flashing White flashing Gradual flashing RGB gradual flashing RG gradual flashing RB gradual flashing GB gradual flashing Flickering RGB Flickering White flickering RG flickering RB flickering GB flickering R flickering G flickering B flickering w EUComtrols EUKT02 RGB60 Standard Product Warranty PRODUCT WARRANTY EuControls warrants that at the time of shipment the standard products manufactured by EuControls and sold hereunder will be free from defects in material and workmanship for a period of three years from the date of shipment Warranty Adjustment Buyer shall notify EuControls immediately if any defect within the warranty period should appear EuControls agrees to repair or furnish a replacement for but not install any product which within three 3 years from the date of shipment by EuControls shall upon examination by EuControls prove defective within the above warranty period No product will be accepted for return or replacement without written authorization of EuControls Upon such authorization and in accordance with instructions by EuControls the product will be returned shipping charge prepaid by Buyer Replacements made under this warranty will be shipped prepaid by Seller Exclusions from Warranty This warranty does not extend to any products manufactured b
3. de EUComtrols EUKT02 RGB60 RGB LED STRIP LIGHTING KIT EUKTO2 RGB60 This kit comes complete with everything you will need to light up your project It includes a deluxe RGB LED controller a mated AC DC power supply 16 4 of LED strip light and six light strip connectors In some cases you may need to splice connecting wire to power the LED strips or make extended turns It is recommended you first read these guidelines completely to understand how the products work and how they can be configured to your desired lighting layout Please note All wiring must comply with local and national electrical codes for Class II lighting If you are unclear on how to install this product please contact a licensed electrician All 120V AC main connections should be made by a licensed electrician What s included in the KIT Part Number Description XR6 30300 RF RGB Controller EUACRE 003 RGB Remote EULSRO260 5 0 LED Strip Light HE AC DC Power Supply KOS Wired Interconnect with End to EUAECON R10 End connectors Butt Connectors Owner s Manual If any parts are missing please call 1 888 535 9580 e The AC DC power supply is UL listed and ready to use in a standard 120V AC outlet Any alterations or wiring modifications i e hardwiring to the 120V AC input power must be completed by a licensed electrician Please check your local codes prior to beginning any project All 12V DC output circuits meet Class II lighting requi
4. ions to the strip e Avoid sharply bending the LED strip solder joints in curves or irregular spaces since this might damage the LED s w EUComtrols EUKT02 RGB60 OPERATIONAL MANUAL Select desired Brightness By pressing or Select desired Speed for fast or for slow Mode Pause Power function function EuControls ON OFF MODE PAUSE BRT CLAG SPD SPoD B y e re Qa R gt Q OuT Ve qe LED CONTROLLER our re eae MODEL XR6 30300 RF SEM POWER INPUT gt T 5 24 gt ee DC 12V esis INPUT 5V VDC C power input OUTPUT MAX 18A IN ALI RGB wires and power connection STUDY KEY Check Code Function Use with Remote The main function of this key is to sync the controller with the wireless remote control in order to prevent interference from other wireless devices When using this key turn Power ON first and press the STUDY KEY on the controller panel then press any button on the remote control NOTE Please clear codes before using check code function when using XR3 30300 RF To Clear Codes Hold the STUDY KEY for 4 to 5 seconds Power ON OFF Select desired Mode Pause function Select desired Brightness Press for high or Select desired for low Speed Press for fast or for slow lt Battery at the back ae EuComf trols Power Supply Output Power 100W Output Voltage 12V DC Output Current 0 8 33A Input Vo
5. ltage AC 100 240V 50 60Hz Range Voltage AC 90 264V 47 63Hz Over voltage Protection 120 min Over current Protection 120 min Load Regulation 5 Ripple and Noise 100mV Operation Temp 0 40 C Storage Temp 20 85 C Operation Humidity 5 95 Size SPECIFICATIONS RGB Controller Input Voltage DC 5 24V Output Power 12V 5V 90W 24V 432W Standby Power 0 5W 3 channel RGB Control 31 control mode functions 8 brightness level adjustments 8 speed level adjustments Remote Control RF remote control Distance up to 30 meters Speed and brightness adjustments Battery Alkaline 27A 12V LED Tape 5050 smd 60 LED meter 12V DC maximum Operation temp 20 50 C Non waterproof View Angle 120 degrees Storage Temp 30 C 80 C Power per meter 14 4watt Color RGB IP20 EUKT02 RGB60 Connector Use for AWG 22 LED strip thickness 0 3mm Current 5A AC DC Voltage 12 24V DC Operation temp 40 105 C Voltage Resistance 1500V AC min Contact Resistor 30m max 1000m min Housing PA6 Contact over Brass Tin Tooth Slice double Tin Size 12 88mm x 15 48mm x 3 3mm L 156 x W 67 x H 40 mm Cord Input cable wire stripped and tinned 18 AWG black power cord 120VAC MODE SELECTION Red Green Blue Yellow Purple Cyan White 7 colors flashing 9 Flashing 2 10 6 colors flashing 11 6
6. rements and are safe for DIY installation w EUComtrols EUKT02 RGB60 e Our commercial grade RGB LED controller has 31 changing modes and 256 grey levels changing in addition to manual controls for Brightness Speed Pause Mode and On Off Please read these guidelines before installing e Disconnect the AC DC power supply before making any cuts or connections e Do not connect power to the LED strip lights while they are coiled on the reel e Do not install or use this kit in wet or damp locations Use LED strip lights only with a low voltage 12V DC power source and 5 24V DC RGB Controller e To protect the eyes do not stare directly into the LED lights when they are lit e Make sure to use the B R G indicators on the LED strip lights to maintain polarity and correct sequencing e For running wires inside walls use properly certified CL2 or better cabling e Do not install Class 2 low voltage wiring in the same runs with AC main power wiring If AC and DC wires cross keep them at 90 degree angles Peel Remove the 3M tape backing from the LED strip lights and stick in place Connect Simply use the wire interconnects and butt connectors to join the RGB strips Cut Locate the cut lines on the RGB strip light and cut strip to desired length Cutting Figure A Figure B Copper pad location Soldered copper pad location ns tej 3 FRR 5 Bari Faz 5 Kei OH Cut the RGB strip light
7. using scissors Make sure to cut strip in the center of the copper pad locations as shown in the Figure A If you cut at a soldered location refer to Figure B You may need to remove the solder from the RGB strip light connection joint in order for the butt connectors to work properly w EUComtrols EUKT02 RGB60 Connecting g Carefully slide the LED tape into the connector so that copper pads on the RGB strip are positioned underneath the connector contacts Insert the RGB strip into the channel under contact tabs Figure 2 Snap the lid down to close the connector Perform a test to be sure that the connection is correct and that the LED s light before proceeding with the Figure 3 final installation Important Make sure to use the 12V B R G indicators printed on the LED tape light to ensure correct polarity and color sequencing 12V i ren SS R oes 6 B R G B R G e If necessary the LED wires can be extended using 4 conductor 22 18 AWG wire But the shorter the length of wire added or the larger the wire gauge the less chance for voltage drop which would allow for higher LED brightness Please consult your electrician if you are unclear about your connections Planning EUKTO2 Kit is designed for indirect lighting applications The light from the LED RGB strip should not be directly visable Every design is unique and the lighting effects depend on your personal preference The installation loc
8. y EuControls which has been subjected to misuse neglect accident improper installation or use in violation of instructions furnished by EuControls This warranty does not extend to or apply to any unit which has been repaired or altered other than at EuControls factory or by persons not expressly approved by EuControls Components purchased or made by Buyer from any supplier other than EuControls shall bear only the warranty given by the manufacturer of that product and EuControls assumes no responsibility for the interface of its product with any other product and such responsibility shall remain with Buyer for interface functionality and intended use Notice The foregoing warranty is in lieu of and excludes all other expressed or implied warranties of merchantability or fitness for use or otherwise EuControls Corporation 19210 S Vermont Ave Ste 310 Gardena CA 90248 United States Toll free sales hotline 1 888 535 9580 Tel 1 810 643 5700 Fax 1 310 643 5688
Download Pdf Manuals
Related Search