Anwenderhandbuch UM DE FL WLAN EPA (5N) - Digi-Key
Contents
1. File name Enter name of the firmware file Update Start firmware update Make sure that TFTP transmission is not blocked by a firewall 2 4 SSC script Configuration via the SSC script can be used if numerous EPAs are to be set up in an identical or similar way A script can be executed on all current Windows PCs without any further installation It allows for fast configurations that can be reproduced without errors SSC is based on the Windows Scripting Host WSH that has been an integral part of all current Windows versions since Windows 98 For a detailed description containing examples please refer to SimpleScriptConfiguration WLAN_00 zip at www phoenixcontact net download PHOENIX CONTACT 2 17 FL WLAN EPA 2 18 PHOENIX CONTACT 8099 en_00 Simple Network Management Protocol SNMP 3 Simple Network Management Protocol SNMP 3 1 General function SNMP is a manufacturer independent standard for Ethernet management It defines commands for reading and writing information and defines formats for error and status messages SNMP is also a structured model which consists of agents and their relevant MIB Management Information Base and a manager The manager is a software tool which is executed on a network management station The agents are located inside switches bus terminal modules routers and other devices that support SNMP The task of the agents is to collect and provide data in2. Durchsuchen IP Configuration Set amp Reboot Ip Address 192 168 0 254 Subnet Mask 255 255 0 0 Default Gateway 192 168 0 254 IP Assignment Static v Set amp Reboot Client Mode Mode Multi Client vi DHCP Relay on v Device MAC EPA MAC Scan Set amp Reboot WLAN WLAN Band WLAN Band Auto Default v Set Band WLAN Network Press Scan to find APs Y Scan Assume amp Set Connection Network SSID PxC Operating Mode Infrastructure Data Rate Auto v Transmit Power 17 Set Security Security Mode None v Set General Mode Standard v Used Channels all IE To To Roaming Profile Background Medium v Service Change Password New Password Confirm Password Set System Identification Device Name epa Description WLAN Ethernet Port Adapter Physical Location unknown ae Contact unknown General Data Set Miscellaneous Event Subscriber Off x Set Save Configuration Read all settings Reload Settings Write all Reboot Figure 2 4 Configuration menu The frequency band can only be selected with FL WLAN EPA RSMA 8099_en_00 PHOENIX CONTACT 2 7 FL WLAN EPA All the sections contain a Set or Set amp Reboot button The parameters of each section are only transferred to the EPA and stored permanently with a click on the
3. Keep Fresnel zone free from any obstacles d J Fresnel Zone Figure 4 1 The Fresnel zone 8099_en_00 PHOENIX CONTACT 4 1 FL WLAN EPA 4 1 2 1 Marginal conditions for planning a wireless path There should be a line of sight especially in the event of longer distances between the antennas of the wireless devices To keep the Fresnel zone free from any obstacles it may be required to mount the antennas at a height of some meters This area should also be free from any other obstacles Table 4 1 Fresnel zone mounting height for the WLAN devices antennas Wireless path distance Antenna height Antenna height d 2 4 GHz r 5 GHz r 100 m 1 7m 1 2m 200 m 2 5m 1 7m 300 m 3 0m 2 1m 400 m 3 5m 2 4m Note the wireless path may also work if obstacles are within the Fresnel zone house tree etc In most cases the decisive factor is the number of obstacles and the area they occupy in the Fresnel zone However there is no clear calculation basis for this It is therefore recommended to perform test measurements Indoors reflections which do not occur outdoors in this way usually dominate in the conventional automation environment and ensure a safe wireless connection even if the Fresnel zone is not free from obstacles 4 1 3 Free space attenuation of the wireless signal Fresnel zone The following table lists the values for free space attenuation which experiences a
4. User manual UM EN FL WLAN EPA 5N Hardware and software for the WLAN Ethernet port adapter versions with 2 4 GHz or 5 GHz and with external antenna connection OGD OO GD GD OGD OO OD Misma INSPIRING INNOVATIONS User manual Hardware and software for the WLAN Ethernet port adapter versions with 2 4 GHz or 5 GHz and with external antenna connection 2012 08 09 Designation UM EN FL WLAN EPA 5N Revision 01 Order No This user manual is valid for Designation Revision Order No FL WLAN EPA Hardware version 2692791 2 1 or later firmware version 2 2 or later FL WLAN EPA 5N Hardware version 2700488 2 1 or later firmware version 2 2 or later FL WLAN EPA RSMA Hardware version 2701169 2 1 or later firmware version 2 2 or later PHOENIX CONTACT 8099 en_01 Internet Subsidiaries Published by Please observe the following notes User group of this manual The use of products described in this manual is oriented exclusively to Qualified electricians or persons instructed by them who are familiar with applicable standards and other regulations regarding electrical engineering and in particular the relevant safety concepts Qualified application programmers and software engineers who are familiar with the safety concepts of automation technology and applicable standards Explanation of symbols used and signal words hazards Obey all safety measures that follow this symbol to avoi
5. C 40 C to 85 C IP65 DIN 40050 IEC 60529 5 to 90 non condensing 10 to 95 non condensing 79 5 kPa to 108 kPa 2000 m above sea level 70 kPa to 108 kPa 3000 m above sea level On a level mounting surface Not required 120 g typical Via M12 conductor cross section 2 5 mm maximum 24 V DC SELV 9V DC to 30 VDC 75 mA 1 8W 1 4 pos M12 socket on the device D encoded Twisted pair cable with a conductor cross section of 0 14 mm to 0 22 mm 100 ohms 10 100 Mbps auto negotiation 100 m 192 168 0 254 WLAN according to IEEE 802 11 2 4 GHz to 58 5 Mbps WLAN according to IEEE 802 11 5 15 to 5 725 GHz to 58 5 Mbps WLAN according to IEEE 802 11b g n 2 4 GHz to 58 5 Mbps WLAN according to IEEE 802 11a n 5 GHz to 58 5 Mbps 20 dBm maximum FL WLAN EPA RSMA 15 dBm maximum 2 4 GHz max 94 dBm 5 GHz max 87 dBm 8099_en_00 PHOENIX CONTACT 5 1 FL WLAN EPA Interfaces Fortsetzung Characteristics Connection WLAN functions Operational mode Configuration Security Mechanical tests Shock test in acc with IEC 60068 2 27 Vibration resistance in acc with IEC 60068 2 6 Free fall in acc with IEC 60068 2 32 Approvals FCC CFR 47 Part 15 ETS 300 328 Conformance with EMC directives Noise emission according to EN 55022 Radio interference field strengths according to EN 55022 Electrostatic discharge ESD according to EN 61000 4 2 Electromagnetic fields according to IEC
6. 2832580 10 2832616 10 2832629 10 8099_en_00 PHOENIX CONTACT 5 3 FL WLAN EPA 5 1 3 Declaration of conformity PHCENIX CONTACT 2701169 CE 00 EG Konformit tserkl rung EC Declaration of Conformity Hersteller Manufacturer PHOENIX CONTACT GMBH amp CO KG Anschrift Address Flachsmarktstra e 8 D 32825 Blomberg Germany Produktbezeichnung Product description FL WLAN EPA RSMA Artikelbezeichnung Article description Artikel Nr Article no 2701169 Das vorstehend bezeichnete Produkt stimmt mit den wesentlichen Anforderungen der nachfolgenden Richtlinie n und deren Anderungsrichtlinien berein The above mentioned product is in line with the essential requirements of the below directive s and their modification directive s 1999 5 EC Funkanlagen und Telekommunikationsendeinrichtungen Radio and telecommunications terminal equipment Fur die Beurteilung der Ubereinstimmung wurden folgende einschl gige Normen herangezogen For evaluation of the conformity following relevant standards were consulted EN 300 328 V1 7 1 EN 301 893 V1 5 1 EN 301 489 01 V1 9 2 EN 301 489 17 V2 1 1 EN 61000 6 2 2005 EN 61000 6 3 2007 A1 2011 Weitere Informationen z B Dokumente Pr fberichte Einschr nkungen etc zur Konformit tsbewertung Additional information for example documents test reports restrictions etc of the conformity assessment Zertifikate einer benannten Stel
7. 61000 4 3 Conducted interference according to IEC 61000 4 6 Fast transients burst according to IEC 61000 4 4 Surge voltages according to IEC 61000 4 5 Panel antenna cannot be replaced FL WLAN EPA RSMA external antenna connection RSMA female Internal Client in an infrastructure ad hoc Via web based management SNMP AT commands or SSC script Authentication open WPA WPA2 PSK LEAP PEAP encryption TKIP AES CCMP WEP 64 128 bits Operation 25g 11 ms period half sine shock pulse Storage transport 50g 11 ms period half sine shock pulse Operation storage transport 5g 10 150 Hz Criterion 3 im Class B Class A Contact discharge 4 kV Air discharge 8 kV 10 V m Criterion A 10 Vans Criterion A Data lines 1 kV Criterion B Power supply lines 0 5 kV Criterion B Data lines 1 kV asymmetrical Criterion B Power supply lines 0 5 kV symmetrical asymmetrical Criterion B Differences between this version and previous user manual versions Rev 00 First version Rev 01 RSMA version updated 5 2 PHOENIX CONTACT 8099_en_00 Technical data 5 1 Ordering data 5 1 1 Products Description 2 4 GHz WLAN Ethernet adapter 5 GHz WLAN Ethernet adapter WLAN Ethernet adapter 2 4 5 GHz RSMA antenna connection Order designation FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA 5 1 2 Accessories Description Mounting kit for wall or mast mounting Mounting kit for DIN rail
8. Fingerprint General Certificate for authentication via PEAP Mode Select roaming operating modes Standard roaming optimization via parameters Seamless roaming uninterrupted roaming with two EPAs operating in parallel Used Channels Select possible wireless channels Channel limitation is used for optimizing the roaming time 8099_en_00 PHOENIX CONTACT 2 15 FL WLAN EPA Table 2 4 Parameter list for the Settings page Fortsetzung Designation Description Roaming Profile Select typical setting for roaming optimization Hold connection no roaming Background search for better access point in short high medium or long low distance Individual loading of individual adapted parameter records templates for special cases RSSI Difference Change password Service Select difference of receive quality as trigger for change in BDP mode Optimized for high data throughput high with a high density of access points or Optimized for long ranges low Password Enter new password for the WBM Make sure to replace the standard password by a secret and secure password for security reasons Retype password Re enter password to avoid typing errors System Identification Device Name Enter device name display for SNMP or on Info page for example Description Enter device description display for SNMP or on Info page fo
9. PHOENIX CONTACT 1 5 FL WLAN EPA m me ae 1 6 Mounting the FL WLAN EPA A minimum distance of 50 cm between modules must be observed when mounting the FL WLAN EPA s Make sure that the antenna is not directly located in front of a metal surface This may ad versely affect the wireless features of the antenna in the long term Observe a minimum distance of 20 cm between devices and personnel 1 6 1 Mounting the FL WLAN EPA on a flat surface Mount the FLWLAN EPA on a level surface and secure the device using two screws e g 84 M3 X 35 8 8 cylinder head screws For the required drill hole spacing please refer to Figure 1 2 on page 1 6 1 6 1 1 Drill hole template and housing dimensions 58 2 283 82 3 228 91 3 583 66 2 598 Figure 1 2 Housing dimensions and drill hole spacing for the device in millimeters inches 1 6 PHOENIX CONTACT 8099 _en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA 1 6 2 DIN rail mounting The FL EPA RMS mounting kit 2701133 is available as an accessory for mounting the device on a 35 mm DIN rail Figure 1 3 Fixing the EPA to the mounting kit for the DIN rail e Fixthe EPA on the base plate using the two screws provided e Place the EPA with the adapter on the top edge of the DIN rail e Push the EPA t
10. Server the EPA itself uses the address permanently set and operates as the DHCP server for other devices on the LAN side start address 192 168 0 1 Client Mode Mode Select operating mode for the LAN connection Single Client connection with layer 2 transparency only one device can be connected Multi Client default one device can be connected with layer 2 transparency and the other device with IP transparency Multi UDP Tunnel connection with layer 2 transparency to multiple devices between two EPAs DHCP Relay Activate DHCP relay When acting as the DHCP relay the EPA can process DHCP requests of devices connected on the LAN side via the wireless interface even if the EPA is in multi client mode and uses the MAC address of a connected device Device MAC Select layer 2 device address MAC of the EPA on the WLAN interface The list shows the MAC addresses of the devices connected on the LAN side which have been identified by means of the Scan button EPA MAC uses the original EPA MAC address UDP Port Port number for UDP tunnel Usually the port number can be used unchanged All the devices can use the same port number Number of Peers Select number of UDP connections 8099_en_00 PHOENIX CONTACT 2 13 FL WLAN EPA Table 2 4 Parameter list for the Settings page Fortsetzung Designation Description Remote IP address Enter
11. The wireless LED of the EPA changes to blue 4 Assign a secret and secure password for the WBM To avoid write errors the password must be entered twice in the New Password and Confirm Password fields Apply the new password with Set From now on the configuration page can only be accessed using this password If the password is lost the device can be reset to the default settings using the MODE button However the entire configuration will also be lost Now configuration is complete 2 8 PHOENIX CONTACT 8099_en_00 Startup and configuration Advanced View When clicking on the Advanced view button additional elements are shown on the right side of the window Ethernet Port Adapter Version 2 2 0 13 53 19 Aug 26 2011 Windows Internet Explorer pm aaa gt EY http 192 168 0 254 4 23 gt lt Au Live Search ee Datei Bearbeiten Ansicht Favoriten Extras 2 Ly Favoriten 3 desktop ini Vorgeschlagene Sites Web Slice Katalog E Ethernet Port Adapter Version 2 2 0 13 53 19 Aug contact m a o Seite Sicherheit Extras FL WLAN EPA 5N Order No 27 00 488 REA 7 AT Commands IP Configuration AT Commands Ip Address 192 168 0 254 Subnet Mask usa Default Gateway 192 168 0 254 u AT Response IP Assignment
12. active access to the configuration page is disabled Cancel Cancel login return to the Info page Table 2 4 Parameter list for the Settings page Designation Description Info Return to Info page The user remains logged in Logout Return to Info page The user remains logged in Advanced View Extend view by AT commands and the firmware update option Load Configuration Load Configuration Load and execute configuration commands from a file In combination with Read all settings the entire configuration can be restored IP Configuration IP Address Enter layer 3 network address IP of the EPA The address must be unique in order to address the WBM during operation 2 12 PHOENIX CONTACT 8099 en_00 Startup and configuration Table 2 4 Parameter list for the Settings page Fortsetzung Designation Description Subnet Mask Enter filter mask for IP addresses default 255 255 0 0 Default Gateway Enter IP address of the transition point to other network segments Not required for communication within the address area IP Assignment Select the type of address assignment Static permanent assignment via the IP Address entry field default The standard value is 192 168 0 254 DHCP address is retrieved from an active DHCP server in the network Inthe case that address assignment fails the EPA uses the address set in the IP Address field Static amp DHCP
13. and the 5 GHz WLAN standard IEEE 802 11 a n This means it can connect any WLAN module to the Ethernet network provided the module also supports standard IEEE 802 11 b g n or IEEE 802 11 a n Industrial devices with WLAN interface include for example industrial PCs or notebooks mobile portable devices industrial barcode scanners RFID readers and weighing systems Figure 1 1 Front view of the FL WLAN EPA 1 2 Factoryline WLAN WLAN IEEE 802 11 b g or a n is a standardized wireless technology which enables extremely rugged and reliable data transmission in metal environments and industrial environments with high levels of interference WLAN has become established as the standard for the wireless transmission of control data in automation networks Factoryline WLAN is the standard compliant optimization for industrial factory automation 8099 _en_01 PHOENIX CONTACT 1 1 FL WLAN EPA Benefits Tap proof and manipulation proof Long range in industrial halls High performance Excellent integration in automation systems The use of Factoryline WLAN is recommended if the following requirements are to be met Very reliable control data in harsh industrial environments Fast data transmission with stable latencies 1 2 1 Device versions Three device versions are available FLWLAN EPA Order No 2692791 FLWLAN EPA 5N Order No 2700488 FLWLAN EPA RSMA Order No 2701169 The devices diffe
14. gives a proper average value Exact values can be calculated with the following formula free space attenuation dB 32 4 20log frequency MHz 20log distance km 4 1 4 Propagation of the radio wave indoors 4 1 4 1 In an industrial hall If the wireless unit is installed in an industrial hall the conditions listed above basically apply The Fresnel zone will not be free there But reflections on metal objects may promote the propagation of radio waves The range of the wireless modules depends on their mounting location and or the position of their antennas In general the antenna should be free from other objects so it can radiate well into the area It should for example not be touched by cables or be surrounded by a metal control cabinet The reference value for the range within an industrial hall is up to 50 meters The actual range may be significantly greater or less than this The variation depends on the environment and the transmission power set Large metal obstacles such as walls or machines may limit the range in that direction This is particularly true if they are permanently located static between the wireless units The range can be limited by reducing the transmission power Thus only certain areas can be covered if desired 8099_en_00 PHOENIX CONTACT 4 3 FL WLAN EPA A more exact estimation of the range can also be achieved by prior simulation The influence of the environment is then also t
15. information or the use of repetitive codes where required by the technology Dynamic Frequency Selection DFS for devices operating in the bands 5250 5350 MHz 5470 5600 and 5650 5725 MHz The maximum antenna gain permitted for devices in the band 5725 5825 MHz shall comply with the e i r p limits specified for point to point and non point to point operation as appropriate Users should also be advised that high powers radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5650 5850 MHz and that these radars could cause interfernce and or damage to LE LAN devices IMPORTANT NOTE IC Radiation Exposure Statement This equipment complies with IC RSS 102 radiation exposure limits set forth for an unconcrolled environment This equipment should be installed and operated with minimum distance 20cm between radiator amp your body This module is intended for OEM integrator The OEM integrator is still responsible for the IC compliance requirement of the product which integrates this module 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into Under such configuration the IC RSS 102 radiation exposure limits set forth for a population uncontrolled environment can be satisfied Any changes or modifications not expressly approved by the manufacturer could voids the users s authority to operate this equipment 8099_en_01
16. no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 8099 _en_01 PHOENIX CONTACT 1 3 FL WLAN EPA To comply with FCC part 15 rules in the United States the system must be professionally installed to ensure compliance with the Part 15 certification It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States The use of the system in any other combination such as co located antennas transmitting the same information is expressly for bidden FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference recei
17. the IP address of the EPA remote peer of the UDP tunnel WLAN Radio WLAN Network WLAN Switch off the internal EPA wireless module for operation on an existing WLAN network tunnel starting point WLAN network scan Search for available WLAN networks Table After clicking on Scan the available WLAN access points are listed with their SSID BSSID channel receive field strength operating mode and security mode Select the desired network from the list and accept the SSID and security mode by clicking on the Assume amp Set button WLAN band only for FL WLAN EPA RSMA Select frequency band 2 4 or 5 GHz In Auto mode both frequency bands are scanned manual defining either of the two frequency bands speeds up the search for a suitable network Connection Network SSID Enter wireless network ID SSID Clients may perform roaming between access points that have the same SSID Operating Mode Select WLAN operating mode Infrastructure client in a WLAN network Ad hoc direct connection between for example two EPAs Channel Select wireless channel for ad hoc connections Ad hoc only in infrastructure mode the access point determines the channel Data Rate Select data rate modulation Auto default automatically selects the maximum possible data rate Transmit Power Enter transmission power in dBm default 15 max Can be redu
18. the MIB The manager regularly requests and displays this information The devices can be configured by writing data from the manager to the MIB In the event of an emergency the agents can also send messages traps directly to the manager saved permanently A All configuration modifications which are to take effect after a device restart must be SNMP interface All managed Factoryline components have an SNMP agent This device agent manages Management Information Base II MIB 2 according to RFC 1213 and private SNMP objects from the Phoenix Contact MIB PXC WLAN MIB Network management stations such as a PC with Factory Manager can read and modify configuration and diagnostic data from network devices via the Simple Network Management Protocol SNMP In addition any SNMP tools or network management tools can be used to access Factoryline products via SNMP The MIBs supported by the relevant device must be made available to the SNMP management tools On the one hand these are globally valid MIBs which are specified and described in RFCs Request for Comments This includes for example MIB2 according to RFC 1213 which is Supported by all SNMP compatible network devices On the other hand manufacturers can specify their own private SNMP objects which are then assigned to a private manufacturer area in the large SNMP object tree Manufacturers are then responsible for their own private enterprise areas i e they
19. 011 09 20 Form establisher Corporate Tachinolsg Blatt Page 1 von of 2 2701169 CE 00 doc 5 4 PHOENIX CONTACT 8099 en_00 Technical data PHCENIX CONTACT 2701169 CE 00 Anhang zur EG Konformitatserklarung Annex on EC Declaration of Conformity vom dated 2012 07 04 Produktbezeichnung Product description FL WLAN EPA RSMA Artikeibezeichnung Article description Artikel Nr Article no 2701169 Die Konformit t mit den wesentlichen Anforderungen der Richtlinie n wird auch f r folgende Produkte bescheinigt The conformity with the essential requirements of the directive s is also certified by the declaration for following products Artikel Nr Article no Artikelbezeichnung Article description 2692791 FL WLAN EPA 2700488 FLWLAN EPA 5N 2701169 CE 00 doc Blatt Page 2 von of 2 8099_en_00 PHOENIX CONTACT 5 5 FL WLAN EPA PHOENIX CONTACT GmbH amp Co KG Flachsmarktstr 8 32825 Blomberg Germany Gm 49 5235 3 00 amp 49 5235 3 41200 ah www phoenixcontact com a Worldwide locations e www phoenixcontact com salesnetwork HOTLINE Should problems occur that cannot be resolved with the help of this documentation please contact our hotline 49 5281 9 462888 5 6 PHOENIX CONTACT 8099 en_00
20. 2 168 0 254 Other settings are not modified 2 2 PHOENIX CONTACT 8099_en_00 Startup and configuration Table 2 1 Operating modes Fortsetzung Mode Description LEDs 4 EPA to EPA bridge wait for configuration Step 1 for establishing a direct connection ad hoc between two EPAs As long as the LED flashes the module waits for a connection request After connection establishment the module accepts IP address 10 0 0 99 EPA to EPA bridge connection establishment Step 2 for establishing a direct connection ad hoc between two EPAs The module initializes connection to a module in mode 4 Wait After connection establishment the module accepts IP address 10 0 0 100 A C EPA to EPA bridge with PROFINET optimization wait for configuration Step 1 for establishing a direct connection ad hoc between two EPAs As long as the LED flashes the module waits for a connection request SafetyBridge transmission requires the web interface to be switched off After connection establishment the module accepts IP address 10 0 0 99 B C EPA to EPA bridge with PROFINET optimization Connection establishment Step 2 for establishing a direct connection ad hoc between two EPAs The module initializes connection to a module in mode 6 Wait SafetyBridge transmission requires the web interface to be switched off After connection establishment the module accepts IP address 10 0 0 100 A B
21. C UDP tunnel in an infrastructure wait for configuration Establishing a UDP tunnel between two EPAs This requires the EPAs to be connected to the WLAN already After configuration the module accepts IP address 10 0 0 99 and is configured as the tunnel end point in the WLAN UDP tunnel in an infrastructure connection establishment via the wireless side of a WLAN Establishing a UDP tunnel between two EPAs This requires the EPAs to be connected to the WLAN already After configuration the module accepts IP address 10 0 0 100 and is configured as the tunnel starting point in the WLAN A D 8099_en_00 PHOENIX CONTACT 2 3 FL WLAN EPA Table 2 1 Operating modes Fortsetzung Mode Description LEDs A Ww O o 10 WLAN UDP tunnel in an infrastructure connection establishment via B D the LAN side of a WLAN Establishing a UDP tunnel between two EPAs After configuration the module accepts IP address 10 0 0 100 and operates as the tunnel starting point in the LAN for communication to the EPA via an existing 11 External wireless wait for MAC address A B D amp amp Aslongasthe LEDs are flashing the EPA waits for the first data packet on the LAN interface The EPA accepts the MAC address as its own MAC address on the wireless side This means that the connected device can be addressed in the network using layer 2 transparency The MAC address is retained
22. Static Set amp Reboot AGUN A Client Mode me f Ke Multi Client v Mods Mutti client AT AGDN DHCP Relay on v Device MAC EPA MAC Scan er Set amp Reboot AT AGCFP WLAN WLAN Network _ AGCFP 0000000000000000000000000000000000000000 Press Scan to find APs _ OK Scan Assume amp Set AT AGFP Connection Network SSID z Operating Mode Data Rate Au AT AGCL Transmit Power 15 Set AGCL 36 40 44 48 Security lok Security Mode None x Set a Roaming E a General Mode Standard v Used Channels All JE o 0 Roaming Profile Background Medium Firmware update from TFTP Server E Server IP Address File name o ee Change Password New Password Confirm Password Set Figure 2 5 Advanced menu Two additional functions are available Display and execution of AT commands Firmware update 8099_en_00 PHOENIX CONTACT 2 9 FL WLAN EPA AT commands All the important configuration options are directly available on the graphical interface For exceptional parameter combinations AT commands can be sent to the EPA or return values can be displayed To do so enter the command in the AT Commands entry field and click on the Send button The result is shown in the AT Response text field For a complete AT command reference please refer to www download phoenixcontact de The AT Response window also shows the c
23. aken into consideration To do so use the FL Wireless Simulation Tool software Order No 2692254 which is available as an accessory PP FL Wireless Simulation Tool Basic 1 0 1 586 Demo EEE File Edit View Settings RF Planning Help 0Gd9 4 ag ES Access Points v FLM_BT_BS_3 100 v Zoom 100 Mouse 77 09 x 26 13 m Figure 4 2 Representation of the radio propagation taking into consideration the walls and machines in the simulation 4 2 LAN operating modes The aim of the WLAN standard was to enable wireless access to the network LAN fora mobile computer Transmission of protocols other than TCP IP or operation of another network following a WLAN client were not in the original focus Therefore there are different concepts on the LAN side with various options for connecting network termination devices 4 4 PHOENIX CONTACT 8099_en_00 Additional information Single client This mode merges the LAN termination device computer controller etc and the EPA so that the rest of the network considers them to be a single device For this the EPA represents itself via the wireless interface with the MAC address of the termination device In this way each network device is able to communicate with the termination device at maximum performance In addition the connection has layer 2 transparency which means that it also transmits protocols that are not using the TCP IP protocol Howeve
24. arger WLAN network The WLAN wireless module of the EPA can be switched off for this purpose Wireless transmission is then via an available WLAN network The UDP tunnel operating mode is provided for tunnel end points which enable communication with mobile termination devices on the mobile side via the EPA wireless module 4 3 PROFINET PROFIsafe via WLAN The PROFIBUS user organization has specified PROFIsafe for wireless transmission paths Positive concept assessments have also been obtained from the BGIA Professional Institute for Safety at Work and TUV German Technical Inspectorate The version of the PROFIsafe profile version 2 4 describes the marginal conditions for the functionally safe transmission of data via WLAN and Bluetooth In particular security aspects for the configuration of wireless components and for safeguarding cyclic data exchange are specified The FL WLAN EPA meets these requirements when it is operated in operating 8099_en_00 PHOENIX CONTACT 4 5 FL WLAN EPA mode BC initiate auto configuration via WLAN EPA to EPA bridge with PROFINET PROFIsafe optimization or ABC initiate auto configuration via WLAN EPA to access point bridge with PROFINET PROFIsafe optimization During configuration of a PROFIsafe connection via WLAN the additional latency of the wireless path must be taken into account The latency for a transmission is typically below 2 ms During planning however a valu
25. ced to 14 dBm for limiting the range The value refers to the electronics The gain of the internal antenna of approximately 5 dBi is not taken into account Setting value 15 therefore results in a radiated power of approximately 20 dBm Security 2 14 PHOENIX CONTACT 8099_en_00 Startup and configuration Table 2 4 Parameter list for the Settings page Fortsetzung Designation Description Security Mode Select security profile The security settings must be identical to those of the wireless network Use Other to implement more unusual combinations of encryption and authentication The settings are automatically taken from the network scan Passkey Format Interprets the passkey as text ASCII or hexadecimal characters 0 F Passkey Enter passkey for encrypted connections The possible characters depend on the encryption method used WEP 64 5 ASCII or 10 HEX WEP 128 13 ASCII or 26 HEX WPA WPA2 8 63 characters ASCII 32 to 126 without A Authentication Select method for secure encryption initialization This setting limits the encryption selection to matching combinations Therefore select authentication first Encryption Select encryption method for securing the data transmission User Name Enter user name for authentication via LEAP or PEAP Domain Enter authentication domain for LEAP or PEAP Certificate
26. d possible in N This is the safety alert symbol It is used to alert you to potential personal injury jury or death There are three different categories of personal injury that are indicated with a signal word DANGER This indicates a hazardous situation which if not avoided will re sult in death or serious injury WARNING This indicates a hazardous situation which if not avoided could result in death or serious injury CAUTION This indicates a hazardous situation which if not avoided could result in minor or moderate injury This symbol together with the signal word NOTE and the accompanying text O alert the reader to a situation which may cause damage or malfunction to the device hardware software or surrounding property This symbol and the accompanying text provide the reader with additional in formation or refer to detailed sources of information How to contact us Up to date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at www phoenixcontact com Make sure you always use the latest documentation It can be downloaded at www phoenixcontact net catal If there are any problems that cannot be solved using the documentation please contact your Phoenix Contact subsidiary Subsidiary contact information is available at www phoenixcontact com PHOENIX CONTACT GmbH amp Co KG Flachsmarktstra e 8 32825 Blomberg GERMANY Should you have any suggestions o
27. diagnostic indicators usnsrsnnnnsennnnennnnnnnnnnnnnn nennen 1 11 2 Startup and CONQUE il 2 1 2 1 Options for device configuration srnsunsennnnnensnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen 2 1 2 1 1 Configuration using the MODE button 422044 200er nenne nennnnnnn nenn 2 2 2 1 2 Configuration examples 2rsuunnsennnnnennnnnnnnnnnnnnnnnnnnnnn rr raras 2 4 2 2 Delivery state default settings 2 24044444rnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 2 4 2 3 Web based management umerssesnnnennnnnennnennnnnnnennnnnnnnnnrnnnnnnnennnsnnnnnnernnnann 2 4 2 3 1 Configuration example 0u240ersnennnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnn nn 2 8 2 4 SSG Script 2 2 Ai ie aA ae Aeneid wae 2 17 3 Simple Network Management Protocol SNMP uuuuu222440ssnnnennnnnnnnnnnnnnnnnnnnnnnnnnnennn nn 3 1 3 1 Generalifunction idiotas ecos 3 1 3 2 supported MIBS curioso Bes ie sn een 3 2 4 Additi nal iniormalion ei AE 4 1 4 1 Propagation of radio WAVES ennennnnsnnenersnnnnnnnnnennnnnnennnnnnnnnnnnnnnnnn ernennen ern nenn 4 1 4 1 1 Basics a as ARE a aed ie 4 1 4 1 2 Propagation of radio waves outdoors Fresnel Zone 4 1 4 1 3 Free space attenuation of the wireless signal Fresnel zone 4 2 4 1 4 Propagation of the radio wave indoors uernnesrssnnnernnnnnnnnnn nenn nennen 4 3 4 2 LAN OperatingiMoOdeS cil adie oeadeh ae
28. e of 8 ms should be assumed Typical values are PROFINET update time gt 8 ms PROFINET timeout gt 24 ms PROF safe timeout gt 150 ms To ensure a stable latency the data load for a wireless path must never be higher that the transmission capacity of the wireless side Problems rarely occur from the actual user data but sometimes from multicast or broadcast data In time critical applications we highly recommend to optimize data traffic using properly configured managed switches 4 6 PHOENIX CONTACT 8099 en_00 Technical data 5 Technical data General data Function Housing dimensions width x height x depth in mm Permissible operating temperature Permissible storage temperature Degree of protection Humidity Operation Storage Air pressure Operation Storage Mounting position Connection to protective earth ground Weight Supply voltage US1 US2 redundant Connection Nominal value Permissible voltage range Typical current consumption on US at 24 V DC FL WLAN EPA power consumption typical Interfaces Number of Ethernet ports Connection format Connection medium Cable impedance Transmission speed Maximum network segment length Default IP address WLAN interface FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA Transmission power Receiver sensitivity Wireless modules that can be connected WLAN antenna WLAN Ethernet adapter 91 x 34 x 66 excluding antenna connection 40 C 65
29. even after a restart 12 access point instead Multipoint ad hoc mode C D a Establishing direct multipoint EPA to EPA connections Note for reasons of performance and safety we recommend operation on an 2 1 2 Configuration examples 2 1 2 1 Example 1 reset EPA module to default settings Switch on the EPA module and press the MODE button after power up to change to configuration mode Now LED A is on Then press the MODE button once until the B LED lights up Once the mode has been selected press the MODE button again and hold it down for at least 2 seconds until the corresponding mode LED goes out The EPA module is now reset to its default settings 2 2 Delivery state default settings By default or after the system is reset to the default settings the following functions and properties are set The password for configuration in the WBM is admin The WLAN AP is supplied with the following IP parameters IP address 192 168 0 254 Subnet mask 255 255 0 0 Gateway 192 168 0 254 DHCPis not activated as the addressing mechanism 2 3 Web based management To configure the EPA via the graphical user interface of the web based management enter the EPA s IP address in the address line of your web browser By default upon delivery or after the system is reset to the default settings the address is 2 4 PHOENIX CONTACT 8099_en_00 Startup a
30. ically starts again from the beginning e Exit configuration mode by holding down the MODE button gt 2 seconds after selecting the desired operating mode until the LEDs flash or go out reset or exit configuration mode If the MODE button is not pressed for a longer period in active configuration mode configuration mode is exited automatically and the EPA starts with its previous settings During configuration using the MODE button not all parameters are rewritten just those required for the operating mode It is therefore possible to make some settings via the web interface or via SNMP or AT commands which are still effective after configuration using the MODE button For example the WLAN channels that are not to be used can be selected in advance If the module has been configured before it is advisable to reset to the default settings prior to configuration using the MODE button This reset can also be performed using the MODE button Table 2 1 Operating modes Mode Description LEDs A B Cc D 1 Activate DHCP server A amp The EPA operates as DHCP server and for example assigns address 192 168 0 1 to a computer which is connected for configuration purposes via DHCP Not to be used for operation in a network 2 Restoring default settings factory defaults B a 3 Resetting the IP address A B Resets the IP address to the default settings 19
31. ice description information only e g used fro SNMP 2 10 PHOENIX CONTACT 8099 en_00 Startup and configuration Table 2 2 Parameter list for Info page Fortsetzung Designation Description Physical Location Device location information only e g used for SNMP Contact Responsible contact information only e g used for SNMP General Data General data information only e g used for SNMP LAN Status IP Address Layer 3 network address IP of the EPA default 192 168 0 254 Subnet mask Filter mask for IP addresses default 255 255 0 0 Default Gateway IP address of the transition point to other network segments Not required for communication within the address area IP Assignment Type of address assignment Static DHCP Relay default static assignment of the IP address via the entry field on the Settings page The standard value is 192 168 0 254 Devices connected via the LAN side can place DHCP requests in the network DHCP IP address of the EPA is retrieved from an active DHCP server in the network Inthe case that address assignment fails the EPA uses the address set in the WBM Static amp DHCP Server the EPA itself uses the address permanently set and operates as the DHCP server for other devices on the LAN side start address 192 168 0 1 LAN MAC Address Layer 2 device address MAC of the LAN connection perma
32. le Certificates by a notified body Anschrift Address Referenz Reference Anschrift Address Referenz Reference Die letzten beiden Ziffern des Jahres in dem die CE Kennzeichnung angebracht wurde The last two figures of the year in which the CE marking was applied nur einzutragen bei der Niederspannungsrichtlinie only to be entered on the low voltage directive K Diese Erkl rung gilt auch f r die im Anhang aufgelisteten Produkte wenn angekreuzt This declaration also applies for the products listed in the annex if marked with a cross Diese Erkl rung bescheinigt die bereinstimmung mit den wesentlichen Anforderungen der genannten Richtlinie n enth lt jedoch keine Zusicherung von Eigenschaften Die Sicherheits und Einbauhinweise der mitgelieferten Produktdokumentation sind zu beachten This declaration certifies the conformity with the essential requirements of the indicated directive s it does not however covenant any characteristics The instructions for safety and installation of the enclosed product documentation have to be observed Blomberg 2012 07 04 sand Se fur Frank Schewe Martin M ller Business Unit I O and Networks Business Unit I O and Networks Development Network Technology Vice President Head of the Business Unit Ansprechpartner contact person Zeichnungsberechtigter authorized signatory Formblatterstelldatum Formblattersteller PSA O0SR TO Date of form establishment 2
33. le brouillage est susceptible d en compromettre le fonctionnement For product available in the USA Canada market only channel 1 11 can be operated Selection of other channels is not possible This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter 1 4 PHOENIX CONTACT 8099 en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and it s gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This radio transmitter identify the device by certification number or model number if Category Il has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device The device could automatically discontinue transmission in case of absence of information to transmit or operational failure Note that this is not intended to prohibit transmission of control or signaling
34. mance of the actual communication For a detailed description of the parameters please refer to the overview at the end of this section 8099_en_00 PHOENIX CONTACT 2 5 FL WLAN EPA Pressing the Settings button changes to the configuration view The configuration page is only displayed after entering the password JLS Login to gain access Password Figure 2 3 Login screen Enter the password and confirm by clicking ENTER or the Login button By default upon delivery the login password is admin For reasons of security it is essential to assign a secure and secret password prior to active operation in the production environment If the operating mode PROFIsafe has been selected via the MODE button the information page is displayed but the configuration cannot be accessed This prevents accidental changing of parameters that might be relevant for the operation of devices with safety functions In this case the configuration can only be accessed by resetting the EPA using the MODE button The configuration page is based on the operation of the device Only the options for the current configuration are shown We therefore recommend to work through the page from top to bottom 2 6 PHOENIX CONTACT 8099 _en_00 Startup and configuration ESNA Info Logout Advanced view FL WLAN EPA RSMA Order No 27 01 169 Load Configuration
35. mission Red Error OFF 8099 _en_01 PHOENIX CONTACT 1 11 FL WLAN EPA Des Color Status Meaning LAN Yellow ON Ethernet link present Flashing Ethernet communication active OFF No Ethernet connection Link Green ON A poor link quality Quality A and B sufficient link quality A B and C good link quality A B C and D excellent link quality 1 12 PHOENIX CONTACT 8099 en_01 Startup and configuration 2 Startup and configuration 2 1 Options for device configuration The EPAs can be configured differently for operation MODE button Typical operating modes such as direct connection of two EPAs as a wireless Ethernet cable can be directly selected via the MODE button on the EPA without the need for a PC For a detailed description please refer to 2 1 1 on page 2 2 Web based management WBM To use all the options the device has a web based management which provides a graphical user interface via a web browser This means that the current operating state can simply be displayed without the use of special software or that the device can be configured using a password For a description of the parameters please refer to 2 3 on page 2 4 AT commands All the EPA parameters can be modified or transmitted to the EPA in an automated manner for example from a program of a controller For development or testing purposes AT commands can also be tra
36. mounting Gray RJ45 plug set for linear cable Green RJ45 plug set for crossed cable RJ45 plug that can be freely assembled M12 Ethernet cable Ethernet D encoded 2 m M12 connecting cable for power supply socket 2 m free wire ends Assembly tool for RJ45 plugs Patchbox 8 x RJ45 CAT5e pre assembled can be retrofitted Patchbox 6 x RJ45 CAT5e and 4 SC Ru glass pre assembled can be retrofitted Patch cables Patch cable CAT5 pre assembled 0 3 m long Patch cable CAT5 pre assembled 0 5 m long Patch cable CAT5 pre assembled 1 0 m long Patch cable CAT5 pre assembled 1 5 m long Patch cable CAT5 pre assembled 2 0 m long Patch cable CAT5 pre assembled 3 0 m long Patch cable CAT5 pre assembled 5 0 m long Patch cable CAT5 pre assembled 7 5 m long Patch cable CAT5 pre assembled 10 0 m long Order designation FLEPA WMS FLEPA RMS FL PLUG RJ45 GR 2 FL PLUG RJ45 GN 2 VS 08 RJ45 5 Q IP20 SAC 4P M12MSD 2 0 931 SAC 5P 2 0 PUR M12FS FL CRIMPTOOL FL PBX 8TX FL PBX 6TX 4FX FL CAT5 PATCH 0 3 FL CAT5 PATCH 0 5 FL CAT5 PATCH 1 0 FL CAT5 PATCH 1 5 FL CAT5 PATCH 2 0 FL CAT5 PATCH 3 0 FL CAT5 PATCH 5 0 FL CAT5 PATCH 7 5 FL CAT5 PATCH 10 Order No Pcs Pkt 2692791 1 2700488 1 2701169 1 Order No Pcs Pkt 2701134 1 2701133 1 2744856 2 2744571 2 1656725 1569391 1504848 2744869 1 2832496 1 2832506 1 2832250 10 2832263 10 2832276 10 2832221 10 2832289 10 2832292 10
37. must ensure that only one object is assigned to an object ID object name and parameters and can be published If an object is no longer needed it can be labeled as expired but it cannot be reused with other parameters under any circumstances Phoenix Contact provides notification of ASN1 SNMP objects by publishing their descriptions on the Internet Reading SNMP objects is not password protected However a password is required for read access in SNMP but this is set to public which is usual for network devices and cannot be modified By default upon delivery the password for write access is private and can be changed by the user 8099_en_02 PHOENIX CONTACT 3 1 FL WLAN EPA il In the case of SNMP the public password is used for read only access and private is used for read write access Another benefit for the user is the option of sending traps using the Simple Network Management Protocol Management Information Base MIB Database which contains all the data objects and variables required for network management Agent An agent is a software tool which collects data from the network device on which it is installed and transmits this data on request Agents reside in all managed network components and transmit the values of specific settings and parameters to the management station On a request from a manager or on a specific event the agent transmits the collected information to the ma
38. nagement station Schematic view of SNMP management Management station SNMP management A 4 gt Trap receiver 1 SNMP traps a i Management objects organized in MIBs m jE 4 l l 687407022 Figure 3 1 Schematic view of SNMP 3 2 Supported MIBs The device supports MIB RFC1213 and the FL WLAN EPA The complete MIB files are available at www phoenixcontact com 3 2 PHOENIX CONTACT 8099_en_02 Additional information 4 Additional information 4 1 Propagation of radio waves 4 1 1 Basics Wireless technology is based on the propagation and receipt of electromagnetic waves These waves are not subject to wear of any kind but respond in very different ways in terms of propagation dispersion diffraction and reflection depending on their frequency The propagation of waves in an area is three dimensional and occurs at different strengths Numerous factors affect this propagation however none of these factors may affect the propagation to the extent that a signal is not safely detected at the recipient 4 1 2 Propagation of radio waves outdoors Fresnel zone
39. nd configuration rs ae http 192 168 0 254 To use all the functions the browser must support HTML 5 The following browsers are supported for example Google Chrome version 10 or later Apple Safari version 5 or later Mozilla Firefox version 3 6 or later Internet Explorer version 9 or later Opera version 10 1 or later Then the information page of the EPA opens Figure 2 2 contact Update Status Auto Update Settings FL WLAN EPA 5N Order No Firmware Version 27 00 488 2 2 1 10 27 04 Sep 26 2011 System Overview System Identification Device Name epa Description WLAN Ethernet Port Adapter Physical Location unknown Contact unknown General Data LAN Status IP Address Subnet Mask Default Gateway IP Assignment LAN MAC Address LAN Status WLAN Status Connected to Network SSID PxC Operating Mode Infrastructure Signal RSSI WLAN Channel WLAN MAC Address WLAN Status BDP Role 192 168 0 254 255 255 0 0 192 168 0 254 Static IP DHCP Relay 00 12 F3 0D 7A A0 00 12 F3 0D 7A A0 Not associated System Overview web page This page displays current information on the operating state of the EPA However the settings cannot be changed here Pressing the Update Status button updates the values once pressing the Auto Update button triggers an automatic update every second The automatic update function causes an additional system load which might reduce the perfor
40. nently assigned LAN Status Current connection status of the LAN connection link up connected This information corresponds to the LAN LED on the device WLAN Status Connected to BSSID or MAC address of the access point the EPA is currently connected to Network SSID Network name SSID of the currently connected network Operating Mode Infrastructure connection to access point or AdHoc direct connection to another termination device PHOENIX CONTACT 2 11 FL WLAN EPA Table 2 2 Parameter list for Info page Fortsetzung Designation Description Signal RSSI Signal strength graphically and as numeric value The four color fields correspond to the Link Quality LED on the device Configure your system so that at least 3 LEDs are on 65 dBm WLAN Channel Wireless channel currently used WLAN Status Indicates whether there is a WLAN connection The indication corresponds to the blue WLAN LED on the device If there is a connection it has a blue background BCP Role Current operating mode of the device if two EPAs are connected in BDP mode for uninterrupted roaming Table 2 3 Parameter list for Login page Designation Description Login to gain access Password Entry field for the password of the configuration page default admin Login Login for configuration If PROFINET optimization is
41. nsmitted to the EPA via the WBM or directly via any web browser For the AT command reference please refer to the Phoenix Contact download center SSC script If easy quick and reliable startup of numerous devices is required even complex configurations can be stored in the form of an SSC script and transmitted to the EPA via the Windows Scripting Host WSH from any Windows PC without the need for special software For detailed instructions and example scripts please refer to 2 4 on page 2 17 SNMP Normally the Simple Network Management Protocol SNMP is used for configuration and maintenance of complex networks It enables central access to the device parameters independent of the manufacturer The EPA provides the corresponding support For a detailed description please refer to 3 on page 3 1 8099_en_00 PHOENIX CONTACT 2 1 FL WLAN EPA 2 1 1 Configuration using the MODE button Figure 2 1 MODE button on the bottom of the FL WLAN EPA Above the MODE button are LEDs A to D for configuration indication General sequence e Connect the module to the power supply e Within 5 seconds of switching on the supply voltage press the MODE button to access configuration mode e Select the desired operating mode by pressing the MODE button until the corresponding LED combination lights up Once you have scrolled through all the LED combinations operating modes the selection automat
42. ommands sent via the graphical interface This overview can simply be used as a basis for automatic configurations from control programs or SSC scripts Firmware update The Firmware update from TFTP Server section can be used to transmit new firmware versions For firmware updates a TFTP server program is required A wide range of products is available on the Internet For an example instruction along with the current firmware version please refer to www phoenixcontact net download Enter the IP address of the TFTP server and the name of the firmware file in the text fields and click on the Update button The firmware is then transmitted to the EPA and installed Most of the settings are retained il During firmware update the autocrossing function is not available Therefore use a switch or a crossed cable Table 2 2 Parameter list for Info page Designation Description Info page Update Status Update Display Auto Update Update display automatically The additional data load may affect the actual communication Settings Change to configuration page Order No Order number of the device Firmware Version Firmware version installed An up to date version is available in the download center at www phoenixcontact com if applicable System Overview System Identification Device Name Device name information only e g used for SNMP Description Dev
43. ountries In some cases there are usage restrictions for the transmission power for indoor and outdoor use The FL WLAN EPA has a maximum transmission power of 100 mW 20 dBm and corresponds to R amp TTE device class 2 Please refer to the list of country approvals to see for which countries the operation of this device has been approved please observe the corresponding usage restrictions An up to date list of approvals for countries can be found in the e shop at www phoenixcontact com Approvals for other countries are available on request Usage restrictions for the FL WLAN EPA France a maximum transmission power of 10 mW 10 dBm is permitted outside buildings Web based management should be used to adapt the transmission power with the inclusion of the antenna data 1 4 Firmware versions and their functions Firmware version 2 xx provides the standard WLAN functions and can be used from hardware version 2 1 or later 1 5 FCC information FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is
44. owards the DIN rail until it snaps into place e For releasing the adapter from the DIN rail pull the latch downwards using a screwdriver and at the same time remove the EPA from the DIN rail 1 6 3 Wall or mast mounting The FL EPA WMS mounting kit 2701134 allows for mounting the EPA to a wall or a mast Figure 1 4 Fixing the EPA to the mounting kit for wall mast mounting 8099 _en_01 PHOENIX CONTACT 1 7 FL WLAN EPA e Fixthe EPA on the base plate using the two screws provided e The two 4 5 mm bore holes can be used for mounting Two steel clamps are provided for mounting the EPA to a mast 25 85 mm NOTE Observe the approved operating temperatures of the EPA when using the EPA outdoors The device is designed for installation in protected outdoor areas e g beneath a porch Direct sunlight may lead to overheating and permanent damage of the device Note observe the applicable regulations for using wireless devices outdoors 1 7 FL WLAN EPA installation interfaces Internal circular Status and diagnostic polarized antenna indicators Fixing holes oo RSMA antenna connection version Supply voltage connection switching input Link Quality and mode LEDs LAN interface Mode button Figure 1 5 View and interfaces of the FL WLAN EPA Fixing holes Using these holes you can install the FL WLAN EPA on a level surface using two screws e g 84 M3 X 30 8 8 cylinde
45. r by using the MAC address only one single termination device can be connected on the wired side of the EPA Multi client default Multi client mode can be used for most applications The EPA can also use the MAC address of a termination device and thus enable connections with layer 2 transparency to this single device Additional devices on the wired side of the EPA can also be connected with layer 3 transparency and are therefore available for most applications on a TCP IP basis As the multi client mode provides a high performance it is recommended for most applications Multi UDP tunnel Depending on the protocol used it may be necessary to communicate with several devices on the wired side of the EPA using layer 2 transparency To do so an EPA is used on either side of the wireless connection The EPA packs the incoming data packets into a UDP packet and sends it to the other EPA The other EPA then unpacks the UDP packet and makes the original packet available again This makes transmission of the packet independent of the protocol used Transmission can be performed via the internal wireless module of the EPA or via any other existing wireless infrastructures The additional protocol data reduces the usable transmission speed when compared to the other modes In the multi UDP tunnel operating mode multiple tunnels can be defined Typically this device is then the tunnel starting point on the LAN side of a l
46. r example Physical Location Enter location of installation display for SNMP or on Info page for example Device Contact Enter contact display for SNMP or on Info page for example General Data Enter additional descriptive text display for SNMP or on Info page for example Miscellaneous Event Subscriber Activate documentation of system events via TCP or Syslog Value Select type of documented values Receive quality RSSI connection or both IP Address Enter IP address of recipient for event messages Save Configuration 2 16 PHOENIX CONTACT 8099_en_00 Startup and configuration Table 2 4 Parameter list for the Settings page Fortsetzung Designation Description Read all settings Use the Read button to read all the EPA settings as AT commands The settings can be copied from this window and saved or used in other programs Reload Settings Read again all values of the WBM fields from the EPA Write all Transmit all the current settings to the EPA Reboot AT Commands AT Commands Trigger reboot of EPA Send Enter AT commands in the text box and transmit to EPA via Send button AT Response Text window Shows the AT commands and their responses Firmware update from TFTP Server Server IP Address Enter IP address of the TFTP server that provides the firmware file
47. r head screws for drill hole spacing see Figure 1 2 on page 1 6 Antenna Devices with an internal antenna these devices are supplied with a circular polarized 5 dB panel antenna This design is particularly suitable in environments where many reflections occur on metal The internal antenna cannot be replaced It is adapted to the frequency band of the relevant product 2 4 GHz or 5 GHz Devices without internal antenna the antenna technology used can be chosen by the user Supply voltage connection The supply voltage is connected via the 5 pos M12 socket plug on the device for the assignment please refer to page 1 10 1 8 PHOENIX CONTACT 8099 en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA Network connection LAN interface in M12 format socket on the device with 10 100 Mbps and auto negotiation Status and diagnostic indicators The LEDs display the status of the Ethernet and WLAN interfaces Figure 1 6 FL WLAN EPA RSMA with external antenna connection 8099_en_01 PHOENIX CONTACT 1 9 FL WLAN EPA 1 7 1 Electrical connection The supply voltage and the trigger signal are connected via the 5 pos M12 plug A encoded labeled Power see Figure 1 5 on page 1 8 1 7 1 1 Pin assignment for the connection of trigger input DI and the supply voltage Pin 1 Vin 9 30 V DC Pin 2 External trigger ground Pin 3 Vin GND 0 V Pin 4 External trigger 9 30 V DC responds to a ri
48. r recommendations for improvement of the contents and layout of our manuals please send your comments to tecdoc phoenixcontact com PHOENIX CONTACT Please observe the following notes General terms and conditions of use for technical documentation Phoenix Contact reserves the right to alter correct and or improve the technical documentation and the products described in the technical documentation at its own discretion and without giving prior notice insofar as this is reasonable for the user The same applies to any technical changes that serve the purpose of technical progress The receipt of technical documentation in particular user documentation does not constitute any further duty on the part of Phoenix Contact to furnish information on modifications to products and or technical documentation You are responsible to verify the suitability and intended use of the products in your specific application in particular with regard to observing the applicable standards and regulations All information made available in the technical data is supplied without any accompanying guarantee whether expressly mentioned implied or tacitly assumed In general the provisions of the current standard Terms and Conditions of Phoenix Contact apply exclusively in particular as concerns any warranty liability This manual including all illustrations contained herein is copyright protected Any changes to the contents or the publication of e
49. r with regard to the WLAN standard used i e the frequencies at which they are operated FL WLAN EPA 2692791 supports standard 802 11 b g nin the 2 4 GHz frequency band FL WLAN EPA 5N 2700488 supports standard 802 11 a n in the 5 GHz frequency band FL WLAN EPA RSMA supports both of these bands 1 3 Country approvals for the FL WLAN EPA The FL WLAN EPA is a WLAN client for integrating Ethernet capable devices into WLAN networks The device uses the international license free WLAN standard which is free of charge and operates in the 2 4 GHz ISM band This enables global use The device meets all the requirements of R amp TTE directive 1999 5 EC Europe R amp TTE Directive 1999 5 EC Effective use of frequency spectrum EN 300 328 V1 7 1 2006 10 f2 4 GHz EN 301 893 V1 5 1 2008 12 f5 GHz EMC EN 301 489 1 V1 9 2 2011 09 EN 301 489 17 V2 1 1 2009 05 EN61000 6 2 2005 EN 61000 6 3 2007 A1 2011 EMC according to EN 61000 6 2 2005 Safety according to EN 60950 1 2006 A1 1 Health according to EN 50371 EN 300 328 V1 7 1 EN 301 489 01 V1 8 1 and EN 301 489 17 V2 1 1 1 2 PHOENIX CONTACT 8099_en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA In addition the following approvals have been performed and passed FCC CFR 47 Part 15 USA RSS 210 Canada Depending on the maximum possible transmission power device operation must be approved or registered in some c
50. relevant button The settings that are not transferred to the EPA via Set are neither activated nor stored In any case complete every section where changes have been made by clicking the Set button 2 3 1 Configuration example Connecting the EPA to a WLAN network The following information is required EPA IP address 192 168 0 90 static Subnet mask 255 255 255 0 Application connect several devices TCP IP protocol only WLAN _ SSID Warehouse1 Security WPA2 AES Key PSK MyKey4Warehouse 1 How to proceed 1 Enter the new IP address subnet mask and gateway if applicable of the EPA Apply the settings with Set amp Reboot At this point the WBM restarts with the new IP address 2 Inthe WLAN section click on the Scan button to determine the existing wireless networks The list also shows Warehouse1 If the network is not within the receive range of the EPA the data can also be entered manually Nevertheless using the Scan button is a particular easy method Click on the Assume amp Set button The data is applied At the same time the security mechanism WPA2 AES and the corresponding parameters PSK key are displayed 3 Enter PSK MyKey4Warehouse1 The security key is not displayed in plain text in the WBM Apply the security settings with Set At this point the connection to the network will be established already
51. s 4 4 4 3 PROFINET PROFIsafe via WLAN ccesceceeceseeeeeeeceeeeaeeeeeeesaeeeeeeseeesnaseeeeenaees 4 5 8099_en_01 PHOENIX CONTACT 1 FL WLAN EPA TOCAN CAMARA SETS BEI dehyde catea dena soees ase faa dave aces A AAA 5 1 5 1 Ordering data arten ie 5 3 5 1 1 Products 2 82 DN 5 3 5 1 2 ACCOSSONIGS Annika tal 5 3 5 1 3 Declaration of conformity zmuneeesnennnennnennnennnnnnnnnnn nennen nennen 5 4 2 PHOENIX CONTACT 8099_en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA 1 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA 1 1 Properties The FL WLAN EPA Ethernet port adapter is a high performance industrial WLAN interface for Ethernet or PROFINET compatible equipment A WLAN access point or another FL WLAN EPA can be used as the access point to the Ethernet network A transparent protocol is used for data transmission on Layer 2 level which ensures easy integration also in Industrial Ethernet networks such as PROFINET or Modbus TCP The FL WLAN EPA meets the PROFINET requirements of conformance class A and the PROFIsafe profile for failsafe communication Observe the information in Sections 4 2 on page 4 4 and 4 3 on page 4 5 The FL WLAN EPA has certified compatibility with the 2 4 GHz WLAN standard IEEE 802 11 b g n The FL WLAN EPA 5N however has certified compatibility with the 5 GHz WLAN standard IEEE 802 11 a n The FL WLAN EPA RSMA is compatible with the 2 4 GHz WLAN standard IEEE 802 11 b g n
52. sing edge Pin 5 n C 4 A coded Male M12 Figure 1 7 View of the supply voltage connection plug on the device contact side not solder side 1 7 1 2 Assignment of the LAN socket Pin 1 Transmit Pin 2 Receive Pin 3 Transmit Pin 4 Receive 2 O O OF O 4 D coded Female M12 Figure 1 8 View of the network connection socket on the device contact side not solder side 1 10 PHOENIX CONTACT 8099_en_01 FL WLAN EPA FL WLAN EPA 5N FL WLAN EPA RSMA 1 7 2 Status and diagnostic indicators Three LEDs are located on the top of the device which indicate various states PWR LAN Figure 1 9 LEDs on the top of the device On the bottom of the device there are four LEDs which display different information depending on the operating mode Link Quality 209 Figure 1 10 LEDs on the bottom of the device The MODE button is used for configuration Please refer to the user manual for more details of this function LEDs A to D are used to indicate the status during configuration see Section Configuration using the MODE button on page 2 2 Des Color Status Meaning PWR Green ON Supply voltage present Flashing Supply voltage too low OFF Supply voltage not present Blue ON blue A WLAN connection has been established purple Purple Attempt to establish a connection to another WLAN red device Flashing blue Data trans
53. ved including interference that may cause undesired operation For product available in the USA Canada market only channel 1 11 2 4GHz can be operated Selection of other channels is not possible This device and its antenna s must not be co located or operation in conjunction with any other antenna or transmitter If this device is going to be operated in 5 15 5 25GHz frequency range it is restricted in indoor environment only FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body IC Statement This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B conforme a la norme NMB 003 du Canada This device complies with Industry Canada license exempt RSS standard s Operation this subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorisee aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si
54. wireless signal at different distances Keep the Fresnel zone free from any obstacles For WLAN 802 11 b g the values apply for 2 4 GHz and for WLAN 802 11 a h the values apply for 5 GHz Table 4 2 Free space attenuation at 2 4 GHz and 5 GHz Distance in m Attenuation at 2 4 GHz Attenuation at 5 GHz 5 54 0 dB 60 0 dB 10 60 0 dB 66 0 dB 20 66 0 dB 72 0 dB 30 69 5 dB 75 5 dB 50 74 0 dB 80 0 dB 100 80 0 dB 86 0 dB 110 80 8 dB 86 8 dB 120 81 6 dB 87 6 dB 150 83 5 dB 89 5 dB 200 86 0 dB 92 0 dB 250 88 0 dB 94 0 dB 300 89 5 dB 95 5 dB 4 2 PHOENIX CONTACT 8099_en_00 Additional information Table 4 2 Free space attenuation at 2 4 GHz and 5 GHz Distance in m Attenuation at 2 4 GHz Attenuation at 5 GHz 350 90 9 dB 96 9 dB 400 92 0 dB 98 0 dB 450 93 1 dB 99 1 dB 500 94 0 dB 100 0 dB 550 94 8 dB 100 8 dB 600 95 6 dB 101 6 dB 650 96 3 dB 102 3 dB 700 96 9 dB 102 9 dB 750 97 5 dB 103 5 dB 800 98 1 dB 104 1 dB 850 98 6 dB 104 6 dB 900 99 1 dB 105 1 dB 950 99 6 dB 105 6 dB 1000 100 0 dB 106 0 dB Calculation for 2 4 GHz free space attenuation dB 100 20log distance km Calculation for 5 GHZ free space attenuation dB 106 20log distance km The 5 GHz band for WLAN covers a frequency range of more than 600 MHz This results in different attenuation values depending on the frequency used The formula
55. xtracts of this document is prohibited Phoenix Contact reserves the right to register its own intellectual property rights for the product identifications of Phoenix Contact products that are used here Registration of such intellectual property rights by third parties is prohibited Other product identifications may be afforded legal protection even where they may not be indicated as such PHOENIX CONTACT Table of Contents Table of Contents 1 FLWLAN EPA FLWLAN EPA 5N FL WLAN EPA RSMA uasssssssssssennnnnnenneneennnnnennnnennnn 1 1 1 1 A i 2 SJPRSESEEFPRFEHEFERSPEFERETERPFFETTTTPEFREFERTEFEFFSTELFERTLSSFETTEPRSTFESTETFEFEFERSSSFTERFFPREIFFFERISCHE 1 1 1 2 Factoryline WLAN coco is 1 1 1 2 1 Device VElSIONS 5 secscaes ie eek tele 1 2 1 3 Country approvals for the FL WLAN EPA uensnssennssensnnnrsnnnnnnnnnnnnnnnnnn anne 1 2 1 4 Firmware versions and their functions uuusssssrsnennernnnennnnnnnnnnnnnnnnnnnnnnnnnnnn nennen 1 3 1 5 FGC information 32 25 mer nis all 1 3 1 6 Mounting the FL WLAN EPA siirast toere aeeie ad nnnnn nn nenn 1 6 1 6 1 Mounting the FL WLAN EPA on a flat surface cenne 1 6 1 6 2 DIN railimounting estoica uam 1 7 1 6 3 Wall or mast mounting uesersnnenesennen nennen nenne nennen nenne nnn nennen nn nn 1 7 1 7 FL WLAN EPA installation interfaces 404neernennnnnnnnnnnnnnnnnnnnnn nn 1 8 1 7 1 Electrical connection iniii N 1 10 1 7 2 Status and
Download Pdf Manuals
Related Search