Kisae America Car Batteries User Manual
Contents
1. System warns battery voltage is low Recharge battery as soon as possible or ES and will shut down shortly system will shut down shortly E06 System warns AC load connected is Check load connected to AC output Reduce close to overload shutdown limit load E07 System warns of high internal Reduce load Check if any object is blocking temperature and will shut down shortly the ventilation of unit E08 Not used 09 E10 Internal battery is overcharged Check battery voltage or if any external high voltage is connected to DC Input Port Estimated Run time of AC Load Following run times are estimates Actual run times may vary Estimate Estimate Run time Load Consumption Home Solar 400 Home Solar 800 Home Backup 400 Home Backup 800 Cordless Phone 5W 55 hrs 65 hrs Home Alarm System 5W 55 hrs 65 hrs Clock Radio 8W 34 hrs 4 hrs Table Lamp 40W 7 2 hrs 8 5 hrs Table Lamp 60W 4 6 hrs 5 5 hrs Energy Saving Light 5x17W 85W 3 5 hrs 4 2 hrs 20 LCD TV 40W 8 hrs 9 5 hrs Flooded Light 300W 35 min 45 min Sump Pump 1 4 hp 300W N A surge too high 45 min drill 700W N A overload 13 min Tips Maximize the runtime of your system During times of power outage here are some tips to maximize your run times for key back up power applications Do not leave appliances on when not in use because they will drain the internal battery For computer use use l2. ALO or AL1 Press and hold Select button for 1 second to toggle between the two settings Once the desired setting is selected press and hold Power button for 1 second to set the desired setting and carry with setting the other features Display will show Fd factory default setting If you desire to use the factory setting press and hold Power and Select button together for 5 seconds to exit the setting mode If you wish to keep all the previous settings on inverter and alarm just press Power button for 1 second and press and hold Power and select button together for about 5 seconds to exit the feature setting mode Note Press and hold Power and Select button together for 5 seconds at any time to exit the feature setting mode See feature setting chart below Unit in normal operation Press Power amp Select together for 5 secs to enter feature select mode Press Power amp Select together for 5 secs to set to select setting and exit feature select mode INO IN1 Press Select for 1 sec to change setting Press Power for 1 sec to set to select setting and Lenter next setting m_e Press Select AL1 for 1 sec to change setting Press Power amp Select together for 5 secs to set to select setting and exit feature select mode Press Power for 1 sec to set to select setting and Lenter
3. is available the Solar Charge indicator located at the display panel should automatically turn on and the indicator should either flash or remain solid depending on the battery status NOTE It is recommended to always charge the internal battery to a 100 state of charge as shown by a steady green on Solar Charger indicator Connect to non KISAE Solar Panel The DC Input port located at the back of the unit comes with PP45 Anderson Powerpole connectors To connect a non KISAE Solar Panel to the Home Solar System use the supplied cable and make your own wire connection to your solar panel through the two bare wire ends Please double check on the polarity before connected The red connector is used to connect to the positive terminal of the Home Solar System and the white connector is used to connect to the negative ground terminal of the Home Solar System CAUTION Reverse polarity Improper connections reversing the wire connection on the solar panel connection box or the connector wiring will cause the unit to malfunction and may permanently damage the unit Damage caused by a reverse polarity connection is not covered by your warranty If you want to make your own connector on your solar panel cable the following parts and the appropriate crimping tools are required e PP45 Red Connector Housing amp 45 amp Contact 1 pc P N 1345 e PP45 White Connector Housing amp 45 amp Contact 1 pc P N 1345G7 The red connector is used
4. to connect to the positive terminal of the Home Solar System and the white connector is used to connect to the negative ground terminal of the Home Solar System Disconnect Solar Panel from Unit e Cover the solar panel with an opaque sheet or flip the solar panel with the solar cell facing a flat ground to minimize the output voltage to zero volts e Verify the Solar charge indicator is off e Disconnect the solar cable connector from the DC Input Port of the unit CONFIGURATION Please read the following table to fully understand unit settings and desire your own desirable settings Unit default setting is Full Automatic In1 Al1 Understanding of Unit Setting Inverter Setting Ind Inverter is disabled unit will not provide backup function when utility power is not available In1 Inverter is set to standby mode Unit will provide backup function when utility power is not available Alarm Setting ALO Audio alarm sound is disabled Alarm will not sound when warning and fault occur AL1 Audio alarm sound is enabled Alarm sounds when warning or fault occurs Unit Function Setting Setting Moge of Unit Function Operation In1 Full AC output is provided by AC utility when utility is available AL1 Automatic Internal battery is automatically charged by the 2A charger AC Factory output will automatically switch to inverter mode power by the default internal battery when u
5. 03 amp HB800 00 03 System has no Unit is off Turn unit on output Unit has shutdown due to various potential conditions Check utility battery voltage and unit settings See Unit Operation section Circuit Breaker is tripped Check AC load connected and press the knob on the circuit breaker to reset When utility is available Power buttons cannot be used to shut down the unit This is normal When system is plugged in to utility it acts as a power bar To shut down the system completely unplug the unit from utility Press Power button to turn unit off How can disable the auto backup feature Desire a manual start up instead of automatic back up See page 11 Backup Disabled setting under Unit Mode Setting SPECIFICATIONS Note Specifications are subject to change without notices Home Solar 400 Home Solar 800 Specification Home Backup 400 Home Backup 800 Inverter Output Power 400W 800W Output Current 3 3A 6 6A Surge Power 800W 1600W Output Voltage 120 VAC 60 Hz Output Frequency 60 Hz Output Waveform Modified Sinewave Peak Efficiency 90 No Load battery draw unit in standby lt 3W USB 5V 750 mA Transfer Switch Protection 10A 15A Supplementary Breaker Internal Charger Charging Current 2 ADC Charging Voltage Absorption Float 14 8 13 7 VDC Charger type 3 stages bul
6. N17 xi KISAE Home Solar 400 HS 400 Home Solar 800 HS 800 Home Backup 400 HB 400 Home Backup 800 HB 800 Owner s Manual a ptt wee RUN u Hi may iy PLETTEH mag Wiig Why Un unin For safe and optimum performance the Home Solar or Home Backup unit must be used properly Carefully read and follow all instructions and guidelines in this manual and give special attention to the CAUTION and WARNING statements PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE Note Because unit contains 2 large battery upon purchasing immediately charge unit for more than 48 hours through the utility or through the DC Input Port solar panel sold separately for more than 72 hours depending on the availability of the sun light To guarantee maximum device performance and life span if the unit is not connected continuously to utility power or charge through the DC Input Port it is recommended to charge the unit after each use and once every 90 days Disclaimer While every precaution has been taken to ensure the accuracy of the contents of this guide KISAE Technology assumes no responsibility for errors or omissions Note as well that specifications and product functionality may change without notice Important Please be sure to read and save the entire manual before using your KISAE Home Solar unit or Home Backup unit Misuse may result in damage to the unit and or cause harm or serious injury Read manual in its entirety bef
7. aptop or desktop computer with LCD monitor instead of with CRT monitor Use small televisions instead of big screen TV s Use small desk lamps 25 to 40 W instead of high wattage lamps Use energy saving light bulbs or fluorescent lamp instead of incandescent or halogen light 6 TROUBLESHOOTING To trouble shoot the unit please note the error code displayed on the main unit and review the Understanding the Error Codes in section 5 Problem Question Symptom Solution Appliance connected to unit malfunction or Products connected to unit do not accept modified sine wave waveform Products are not compatible with the modified sine wave output produced by the unit See AC load connected to the overheat unit on page 11 Insufficient Battery is not fully charged Charge battery by leaving the unit run time plugged to the utility for more than 48 hrs to fully charge the battery or leave the optional solar panel plugged into the battery box for more than 72 hrs Solar Charger Solar panel cannot supply Check location and direction of solar indicator is not ON when optional solar panel is connected sufficient power to start the solar charger and charge the battery panel Check the connection and polarity of the solar panel plug to the DC Input Port Wrong wire connection on Verify solar panel junction box not suitable for model solar panel junction box connection HB400 00
8. ately for used on Home Solar unit plugged into the unit to charge the internal battery Understanding the unit features e e e Input circuit breaker mina KISAI w USB Output 2 7 7 7 7 pi RL Lighter Socket AC Outputs Da a e o re am 0224 atin AC Input socket DC Input Port not available on HB400 00 03 or HB800 00 03 ALLLLLLLLLE REREEEREREAR CULLLLILILELI COILILILILI TOUTT COIIIIIIT TUTTE mageeneenens Front view Rear view Select button used for feature setting and display function Power button Status indicator Solar Charge indicator not available on HB400 00 03 or HB800 00 03 Control and Display Panel Main Unit Installation IMPORTANT The AC plug on the power supply cord is used as the disconnect device The socket outlet shall be installed near the equipment and shall be easily accessible for rapid disconnect To install the unit connect the AC power cord IEC end to the back of the unit Plug the other end of the AC input power cord directly into a wall outlet and unit is ready to use Unit will automatically turn on e lf the battery capacity is low Status indicator on display panel turns to flashing green and display shows battery capacity and the unit will automatically charge up the battery e lf the battery is full Status indicator will turns to solid green and display show Ful Unplug the input power cord to si
9. er up USB powered handheld device Using the 12V DC port The 12V DC port on the system provides standard 12V 15A maximum DC current to power up 12V lighter plug type automotive handheld appliance AC Load connected to the unit Although the unit can provide high surge power up to two times the rated output power some appliances may still trigger the unit s protection system A higher power system like Home Solar Kit 1800 HS 1800 60 00 is required for those appliances Some appliances like speed controllers found in some fans and AC chargers for some power tools may not like the modified sine wave generated by the inverter Those appliances may not work or may be damaged if they are connected to the inverter If you are unsure about powering any device with the inverter contact the manufacturer of the appliances Unit Mode Setting Mode i Display Condition Full Solid Ful AC output is supplied by utility power Internal Automatic green battery is fully charged Int Alt Flashing Battery AC output is supplied by utility power Charging green capacity in of internal battery by the 2A charger is in progress factory Solid Flash between AC output power is generated by the inverter default amber Output Power using the internal battery and or from the setting in kW amp battery optional KISAE solar panel capacity in Flashing Same as Same as above and utility AC power is just amber above detected a
10. k absorption float DC Input Port not applicable for model HB400 00 or 03 HB800 00 or 03 Charging Current 8A maximum Charging Voltage 14 8 13 7 VDC Input DC Voltage Range 9 26 VDC maximum Charger Type PWM control 12V DC Port Voltage 12V Current 15A DC Maximum Protection 15A automatically reset Battery Battery Capacity 12V 34Ah 12V 40Ah Battery Type Sealed Lead Acid Safety and Environmental Conformance Conforms to UL 1778 Certified to CSA C22 2 no 107 1 Agency Markings cETLus Operating Temperature 0 C to 40 C 32 F to 104 F Storage Temperature 20 C to 40 C 4 F to 104 F Relative Humidity 5 90 noncondensing Operating Altitude Up to 9 843ft 3000 meters above sea level Weights and Dimensions Weights HS400 00 31 0 Ibs 14 1 kg HS800 00 34 3 Ibs 15 6 kg HB400 00 or 03 30 0 Ibs 13 6 kg HB800 00 or 03 33 3 Ibs 15 1 kg Dimensions 10 x 6 x 10 27cm x 16 cm x 26cm KISAE BATTERY CAR BATTERIES
11. mulate power failure and the indicator on display will turn amber indicating unit is running in backup power mode AC output is now being provided from battery power e Reconnecting the AC power cord back to a wall outlet will switch unit back to standby mode and AC output is now being provided directly from utility power again e The unit is successfully installed and functioning properly PV Solar Panel Installation Not available for Home Backup 400 400LA HB400 00 03 amp Home Backup 800 800LA HB800 00 03 For the system comes with a DC Input Port the internal solar charge controller rated at 140W 17 5V 8A that provides an alternative method to charge the internal battery It is designed to be used with the optional KISAE 40W and 80W solar panel If a non KISAE Home Solar panel is used be sure the solar panel is designed for a 12V battery system with 8A maximum current 17 5V rated voltage and open circuit voltage less than 26 VDC Please refer to the specifications label on the solar panel before connecting Do not connect to a PV source capable of delivering more than 140W 17 5V 8A The solar charge controller is a fully automatic self sustaining device that will initiate the charge cycle only when solar power is available It runs independently from the built in AC charger When a solar panel is connected to the DC Input port the Solar Charge indicator located at the display panel indicates the charging status of the inte
12. nd AC output will switch to utility power within seconds Solid red E01 E10 Error on unit is detected AC output is disconnected See Trouble shooting section Full Same as Full Automatic mode but with audio alarm mute if error occurs The Automatic unit fault protection features remain active Silent Ini AIO Backup Solid Ful AC output is supplied by utility power Internal Disable green battery is fully charged In0 AI1 Flashing Battery AC output is supplied by utility power Charging green Capacity in of internal battery by 2A charger is in progress Backup Same as Backup Disabled mode but with audio alarm mute The unit fault Disable protection features remain active with Alarm Disable Ino AIO Understanding the Error Code Error Condition Corrective Action Code E01 System senses battery voltage is low Recharge battery immediately and restart and has shutdown unit System senses battery voltage is high E02 and has shutdown Check battery voltage or if any external high voltage DC source is connected to DC Input Port System AC output is overloaded or E03 short circuited and has shutdown Check load connected to AC output Reduce load and restart the unit System senses high internal E04 temperature and has shutdown Turn unit off Wait for 15 minutes before restarting Check if any object is blocking the ventilation of unit
13. next setting Factory Press Power amp Select Default together for 5 secs to factory default and exit Press Power for 1 sec to enter next feature select mode setting and factory default is not set UNIT OPERATION WARNING RISK OF EQUIPMENT DAMAGE e Do not plug surge protected power bars into the unit s 120 VAC outlets The surge protected components on the surge protected power bar may not like the modified sine wave output generated by the unit e Do not connect an AC power source such as utility power or a generator to the 120 VAC outlets e Do not connect the unit s AC power input cord to its 120 VAC outlets Quick Unit Operation Guide Turn ON and OFF the 120 VAC and USB when Utility AC is not available Press and hold the Power button for 1 second until a beep is sounded Display will show the measured battery capacity and output power alternatively Status indicator will turn green 5V is available at the USB port and 120 VAC is available at the AC socket Press Power button to turn unit off to save battery power Turn ON and OFF the 120 VAC and USB when Utility AC is available When utility is available the unit will perform like a power bar and the AC output cannot be disconnected unless the AC plug on the unit is removed and the Power button is held for a second to turn unit off Using the USB port The USB port on the system provides standard 5V 750mA power to pow
14. nt generate uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help LIMITATIONS ON USE Do not use in connection with life support systems or other medical equipment or devices BATTERY RECYCLING The unit is designed to provide years of service However the internal battery is not designed to be user replaceable Lo Because the internal battery installed inside the battery box contains lead which can be hazardous if exposed to the environment the battery box should be recycled or safely disposed of at your local recycling depot Do not dispose of the battery box with common household waste Please ask your local authorities about recycling services that are available in your area 2 PRODUCT DESCRIPTION Fo
15. ore using the unit and save manual for future reference Product Number KISAE Home Power System HS 400 00 KISAE Home Solar 400 HS 800 00 KISAE Home Solar 800 HB 400 00 KISAE Home Backup 400 HB 800 00 KISAE Home Backup 800 HB 400 03 KISAE Home Backup 400 LA HB 800 03 KISAE Home Backup 800 LA Document Part Number MU HS400 rev 1 0 INTRODUCTION Thank you for purchasing the KISAE Home Solar unit or KISAE Home Backup unit With our state of the art easy to use design this product will offer you reliable service for providing a rechargeable power source for your home cabin or campsite With its highly technical design and comprehensive features the KISAE Home Solar unit or KISAE Home Backup unit will provide you with a simple yet effective system during power outage or use AC power everywhere when you need it For KISAE Home Solar unit it can run many AC powered appliances whenever you need power The automatic transfer switch built inside means that it can switch seamlessly from household utility power to battery power or the solar power you generate from the sun NOTE Upon purchasing immediately charge unit through utility power for 48 hours or through the DC Input Port through solar panel sold separately for more than 72 hrs To guarantee maximum device performance and life span it is recommended to continuously connect the unit to utility power or solar panel to top up the internal battery or else to charge the unit after each u
16. p fresh water and soap on hand in the event battery acid comes in contact with eyes If this occurs cleanse right away with soap and water for a minimum of 15 minutes and seek medical attention e Batteries produce explosive gases DO NOT smoke or have an open spark or fire near the system e Keep unit away from moist or damp areas e Avoid dropping any metal tool or object on the battery Doing so could create a spark or short circuit which goes through the battery or another electrical tool that may create an explosion WARNING Shock Hazard Keep away from children e Avoid moisture Never expose unit to water e Unit provides 120 VAC from inverter or by pass utility power treat the output sockets the same as regular wall AC sockets at home WARNING Explosion hazard e DO NOT use the unit in the vicinity of flammable fumes or gases such as propane tanks or large engines e AVOID covering the ventilation openings e Always operate unit in an open area e Prolonged contact to high heat or freezing temperatures will decrease the working life of the unit Unit exposure to these elements may lead to cracking and decreased capacity of the internal battery FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipme
17. r Home Solar 400 HS400 00 and Home Solar 800 HS800 00 package includes the items list below e Main unit HS400 00 or HS 800 00 e DC Input Cable e AC Input Cable e Owner s manual For Home Backup 400 or 400 LA HB400 00 or 03 and Home Backup 800 or 800 LA HB800 00 or 03 package includes the items list below e Main unit HB 400 00 or 03 or HB 800 00 or 03 e AC Input Cable e Owner s manual Ic eee DI nn out Ezz i 7 li 7 T Wi tt Owner s gt s 4 A PLANE manual SS gt _ gt AC Input Cable sx lt my DO Hoi Hitt Witt mm Solar panel sold separately for wants DC Input Cable used on Home Solar model np im not included on models HB400 03 and HB800 03 3 INSTALLATION WARNING FAILURE TO FOLLOW THESE INSTRUCTIONS CAN DAMAGE THE UNIT Before beginning your unit Installation please consider the following e The unit should be used or stored in an indoor area away from direct sunlight heat moisture or conductive contaminants The solar panel sold separately for used on Home Solar unit of course can be installed outdoors where the best access to sunlight occurs e When placing the unit allow a minimum of three inches of space around the unit for optimal ventilation e Charge battery immediately upon purchasing this product e To ensure optimum battery run time and life expectancy leave KISAE Home Solar continuously plugged into utility AC power and or leave solar panel sold separ
18. rnal battery Note If insufficient charge capacity is available from the solar source it is recommended to use the built in AC charger to complete the battery charging process through the utility once a month Solar Input DC Input port WARNING Shock fire and energy hazards Make sure the solar panel is covered with an opaque sheet or facing the ground before connecting or disconnecting the cable wire to the DC Input Port located at the back of the unit All wiring must be done in accordance with applicable local and national electrical wiring codes Connect solar panel with higher voltage or current rating will permanently damage the unit and may cause fire and energy hazard Connect to optional KISAE Solar Panel e Cover the solar panel with an opaque sheet or facing the ground before connecting the cable wire e Plug in the DC cable connector to the DC input port located at the back of the unit Please note the polarity of the connector before connected Improper connections reversing the wire connection on the solar panel connection box will cause the unit to malfunction and may permanently damage the unit Damage caused by a reverse polarity connection is not covered by your warranty e Remove the opaque sheet or flip the solar panel with solar cell surface facing upwards Adjust the mounting fringe of the solar panel to have the solar cell surface facing directly to the sunlight to achieve the maximum power When sunlight
19. se and once every 90 days For KISAE Home Backup unit it can run many AC powered appliances whenever you need power The automatic transfer switch built inside means that it can switch seamlessly from household utility power to battery power NOTE Upon purchasing immediately charge unit through utility power for 48 To guarantee maximum device performance and life span it is recommended to continuously connect the unit to utility power to top up the internal battery or else to charge the unit after each use and once every 90 days IMPORTANT SAFETY INFORMATION This manual contains important safety information for unit Each time before using the unit READ ALL instructions and cautionary markings on or provided with the system and all appropriate sections of this guide The unit contains no user serviceable parts See Warranty section for how to handle product issues FIRE AND OR CHEMICAL BURN HAZARD e Do not cover or obstruct any air vent openings and or install in a zero clearance compartment e Do not use the unit if the unit is visibly leaking some type of liquid It is possible that the internal battery has been damaged and battery acid may have spilled FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN DEATH OR SERIOUS INJURY e When working with electrical equipment with lead acid batteries have someone nearby in case of an emergency e Wear eye protection and gloves e Avoid touching your eyes while using this unit e Kee
20. tility is not available Audio alarm is enabled and will sound when any warning or fault occurs Inf Full Same as Full Automatic mode but with alarm disabled Audio ALO Automatic alarm will not sound when any warning or fault occurs The unit Silent fault protection features remain active and will shut down without audio warning when fault occurs Ind Backup AC output is provided by AC utility when utility is available AL1 Disabled Internal battery is automatically charged by the 2A charger Inverter is disabled and no backup power occurs when AC utility is not available Audio alarm is enabled and will sound when any warning or fault occurs Ind Backup amp Same as Backup Disabled mode but with alarm disabled Audio ALO Alarm alarm will not sound when any warning or fault occurs The unit Disabled fault protection features remain active and will shut down without audio warning when fault occurs To change unit function To enter the feature setting mode press and hold Power and Select button together for about 5 seconds until a beep is sounded Display will show current inverter setting as InO or In1 Press and hold Select button for 1 second to toggle between the two settings Once the desired setting is selected press and hold Power button for 1 second to set the desired setting and carry on with setting the other features Display will show current alarm setting as
Download Pdf Manuals
Related Search