Manual (english)
Contents
1. Foam Machine VF 120 FORMS TO COM ANSIVUL erpoog FT CERTIFIED TO d CAN CSA STD t 222 2 No 104 get sr D m m 8700333 VARYTEC Table of content A A ees VARYTEC 1 Safety instructions FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperatureAvoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 41 F 5 C or exceeding 95 F 35 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise ouch as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the player for an extended period of time be sure to disconnect the plug from the receptacle 3 9 VARYTEC 2 Introduction Thank you2. for choosing an Varytec Special Effects Machine You now own a rugged and powerful state of the art machine Prior to use we suggest that you carefully read all of the instructions By following the suggestions found in this user manual you can look forward to the reliable and satisfactory performance of your Varytec Foam Machine for years to come Please follow these operation safety and maintenance instructions to ensure a long and safe life for foam machines 3 CAUTION Danger of electric shock 1 Keep this device dry 2 Forinside use only Not designed for outside use 3 Forthe 110V models use 3 prong grounded electrical outlet only Prior to use take care to determine that the unit is installed at the rated voltage 4 Always unplug your ANTARI Snow or Foam Machine before filling its tank 5 Keep foam machine upright 6 Turn off or unplug when not in use 7 This machine is not water or splash proof If moisture water or snow foam liquid gets inside the housing immediately unplug the unit and contact a service technician or your dealer before using it again 8 There are no user serviceable parts inside Refer to your dealer or other qualified service personnel 9 Foradult use only These machines must be installed out of the reach of children Never leave the unit running unattended 10 Never aim the output nozzle directly at people 11 Locate the machine in a well ventilated area Never cover the unit s v
3. taking into operation for the first time the installation has to be approved by an expert 7 Operation 1 Plug power cord into a grounded electrical outlet Turn the power switch on rear of unit to the ON position 2 The machine will begin producing foam as soon as it is turned on To stop the foam turn the power switch to the OFF position Important Always monitor tank fluid level during operation Running a foam machine without fluid can permanently damage the unit If you experience low output mechanical noise or no output at all unplug immediately Check fluid level the external fuse remote connection and power from the wall If all of the above appears to be O K plug the unit in again If you are unable to determine the cause of the problem do not simply continue pushing the remote button as this may damage the unit Return the machine to your dealer 8 Maintenance Do not allow foam liquid to become contaminated Always replace the caps on the liquid container and the snow machine liquid tank immediately after filling Before storing flush out system with clean water Foam Liquid Fill with Varytec Foam Liquid or other dealer recommended high quality water based snow or foam fluid Any other types of fluid can damage the unit Save these instructions 7 9 VARYTEC Importeur B amp K Braun GmbH Industriestra e 1 D 76307 Karlsbad www bkbraun com info bkbraun com X RoHs Ge
4. e national norms during the installation The installation must only be carried out by an authorized dealer This device is constructed for a standing installation only If the device is to be installed overhead the following safety instructions are binding 5 9 VARYTEC The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation When rigging derigging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material a
5. ents In order to guarantee adequate ventilation allow a free air space of at least 20 cm around the sides and top of the unit Danger of explosion Never add flammable liquids of any kind oil gas perfume to the snow liquid Pay attention to all warning labels and instructions printed on the exterior of your Varytec Foam Machine Use only the high quality foam liquid that your dealer recommends Always make sure there is sufficient liquid in the machine s liquid tank If your Varytec machine fails to work properly discontinue use immediately Drain all liquid from the tank pack the unit securely preferably in the original packing material and return it to your Varytec dealer for service 4 9 VARYTEC 4 Unpacking and Inspection Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact Accompanying the S 120 foam machine should be a hanging bracket and fluid tank If any equipment is missing contact your dealer immediately Before beginning your initial setup on the Foam Machine make sure that there is no evident damage caused by transportation In the event that the unit s housing or cable is damaged do not plug it in and do not attempt to use it until after contacting your dealer for assistance 5 Setup 1 Remove all packing materials from shipping box Check that all foam and plastic padding is removed especially in the nozzle area 2 Place the machine on a f
6. lat surface and remove the liquid tank cap 3 Fill with Varytec Foam Liquid or other dealer recommended high quality water based snow or foam fluid Any other types of fluid can damage the unit When filled place cap back on liquid tank 6 Installation The Foam Machine may be installed at floor level or suspended overhead Install the Foam machine in a well ventilated area Never cover the unit s vents In order to guarantee adequate ventilation allow a free air space of at least 20 cm around the sides and top of the unit Install the device out of the public area Please consider that liquid may be spilt during operation around the device The resulting slippery surface can cause accidents Position output of foam away from persons The minium distance should be 1 5 m Only install the machine on scratch resistant and water resistant surfaces Please make sure that the inclination angle does not exceed 15 DANGER OF FIRE When installing the device make sure there is no highly inflammable Material decoration articles etc within a minimum distance of 0 5 m This device is constructed for a standing installation only If the device is to be installed overhead the following safety instructions are binding The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation DANGER TO LIFE Please consider the EN 60598 2 17 and the respectiv
7. n m
8. nd the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices in hanging installations may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s weight Mount the device to your trussing system using an appropriate clamp 6 9 VARYTEC For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick link with screw cap Pull the safetyrope through the hole in the mounting bracket and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope which already has held the strain of a crash or which is defective may not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation Screws DANGER TO LIFE N Before
Download Pdf Manuals
Related Search