user manual 55
Contents
1. Carrying Notice This monitor is heavy please follow as below instruction when you ready to carry the monitor If not it may cause an injury Legamaster 23 Legamaster Wall Mount Safety Notes 1 Please make sure if the bracket is fixed to the solid wall solid pillar for fear of falling due to heavy weight 3 Please don t install the bracket directly under the sunshine or humidity high temperature places for fear that the quality is effected LA J T S y 7 11 4 Installing the bracket over 10 cm from each wall side and begin vertical to the ground is the suggested installing position 24 Legamaster International B V Kwinkweerd 62 e Postbus 111 e 7240 AC Lochem tel 31 0 573 713000 e fax 31 0 573 713001 email info legamaster com e internet www e legamaster com Legamaster We make communication visible Jedding2. USER MANUAL PROFESSIONAL e Screen FLEX 55 Full HD LCD touchscreen monitor Important Please read this user manual thoroughly and completely before operating this monitor Legamaster We make communication visible ENGLISH Legamast We make communication vi Legamaster We make communication visible Legamaster CONTENTS 1 Important Safety Instructions Safety Precautions Installation when installing the monitor please follow the instructions in the manual Use Cleaning 2 Warning For Use Use Exemptions 4 Package E Unpacking Contents of accessory bag A Apa OO OO Environmental state Power Input Power Interface Signal Source Input 6 Operating the Monitor mu A AUU oO Vi a OY O 0 SS NN The side controller of the monitor 8 The Remote Control RCU Instructions 8 Change The RCU Battery 9 Display Mode 9 Adjusting the Volume 9 Selecting the input source 9 PIP mode 10 PIP Screen Table 10 OSD On Screen Display Menu Function 11 On Screen Display OSD 13 Navigating through the Menu System 14 Display Settings Menu 15 Audio Settings Menu 15 Basic Settings Menu 16 Advanced Settings Menu 16 System Status Menu 17 7 Default Setting 17 4 8 Touch Operation 18 ES 9 Table supported timings 19 E 10 Specification 20 TES Dimensions 21 11 Troubleshooting 22 4 12 Compliance 22 13 Appendix 23 f Moving and Carrying
3. 19 Touch CAL 230 V a 20 IR extender Mini jack Power Interface Main power switch AC socket Please see the chapter Power input The side controller of the monitor The remote control RCU RS 485 RS 485 RS232CIn ip Out C iil 9 a 12 3 4 5206 8 11 1213 pcp om 6 OO 10 14 sgn acm ort n a lt a lt a 2 a lt HDMI1 HDMI 2 DVI Wi LL PC IR SPDIF Component Comp audio S video n Ext ut JM k 16 15 17 HDMI Cable na HDMI Cable B DVI Cable MBit 0 VGA Cable Blue White White Red Legamaster 6 Operating the monitor The side controller of the monitor The Remote Control RCU Instructions Input Interface No Function Description 1 Turns the monitor on and off 2 INFO Provides source and resolution information 3 VGA Selects the PC RGB source DVI Selects the PC DVI source 557 HDMI 1 Selects the HDMI source 1 4 COMP1 Selects the Component source bg ia i AV 1 VIDEO 1 Selects the Composite Video source bi Pe HDMI 2 Selects the HDMI source 2 S80 5 COMP 2 Not available at this model AV 2 VIDEO 2 Not available at this model 6 PIP Turns the PIP feature on and off S V Sele
4. 80 Legamaster Color Temp and Gamma Gamma RColor Temp Red Gain Green Gain Blue Gain Red Offset Green Offset Blue Offset Adjusts red green blue gain and red green blue offset Options Off 2 2 Default 2 2 Options User 5000K 6500K 7500K and 9300K Default 9300K Set Color Temperature to User Mode in order to adjust this setting Range 128 384 Default 256 Set Color Temperature to User Mode in order to adjust this setting Range 128 384 Default 256 Set Color Temperature to User Mode in order to adjust this setting Range 128 384 Default 256 Set Color Temperature to User Mode in order to adjust this setting Range 50 50 Default 0 Set Color Temperature to User Mode in order to adjust this setting Range 50 50 Default 0 Set Color Temperature to User Mode in order to adjust this setting Range 50 50 Default 0 14 Display Settings Menu This menu is used for common source adjustments MAIN Aspect Ratio Zoom Auto Scan Select Source PIP PIP Mode PIP Position Aspect Ratio Display Settings Main Aspect Ratio Full Screen Zoom Auto Scan Select Source PIP PIP Mode PIP Position Aspect Ratio Side By Side Scale Auto Scan Select source The Display Setting Mode Changes the picture aspect ratio Press lt or P to select the following options Option Full screen Pillar Box Letter Box
5. Auto Scan Select source Navigating through the Menu System 1 With the power on press MENU The Image Settings menu will display 2 Within the menu use A V gt and ENTER to navigate through the menus and adjust options 3 Press MENU to return to the previous menu To exit the menu system press EXIT Image Settings Menu This menu is used for making common image adjustments Scheme Brightness Contrast Sharpness Saturation Hue Back Light Image Settings Scheme Brightness Contrast Sharpness Saturation Hue Backlight Color Temperature amp Gamma Press lt or gt to select one of the following Options User Vivid Cinema Game Sport Default User Increases or decreases the brightness of picture Press d or P select the desired level and then press ENTER Range 0 100 Default 50 Increases or decreases the contrast of picture Press or P select the desired level and then press ENTER Range 0 100 Default 50 Adjusts the definition of picture Press lt or P select the desired level and then press ENTER Range 0 24 Default 10 Adjusts the brilliance and brightness only Video Mode Press or P select the desired level and then press ENTER Range 0 100 Default 50 Increases or decreases the green hue Only Video Mode Press or gt select the desired level and then press ENTER Range 0 100 Default 50 Range 0 100 Default
6. Bottom Right 5 To switch the main source and the subsource Using the remote press SWAP SWAP PIP Screen Table HDMI 1 HDMI 2 DVI HDMI 1 HDMI 2 VGA DVI Component S Video Video Component Legamaster 6 To switch audio between the main source and the subsource Using the remote press AUDIO 7 Note For additional PIP functionality press MENU and navigate to the Display Settings menu Use the arrow buttons A W to navigate to the desired PIP feature and press ENTER Press to toggle through the associated options and press ENTER to select the highlighted option Main Source 8 Side by Side Picture by Picture Press P POSITION button choose Side by side mode then the main source and the subsource will be on the screen display Video S Video 10 OSD On Screen Display Menu Function Graphics Mode Main Menu Image Settings Display Settings Audio Settings Basic Settings Advanced Settings System Status Sub Menu Sub Sub Menu Scheme Brightness Contrast Sharpness Saturation Hue Backlight Gamma Color Temp Red Gain Gamma amp Green Gain Color Temp Blue Gain Red Offset Green Offset Blue Offset Aspect Ratio Zoom Wan Auto Scan Select source PIP mode PIP Position Aspect Ratio PIP Side by Side Scale Auto Scan Select source Volume Bass Treble Balance HDMI Audio Input OSD Transparent OSD Location OSD Zoom OSD Rotation
7. Native Default Full screen Range 0 10 Default 0 Range On Off Default On Options VGA HDMI1 HDMI2 DVI Video S Video Component Default VGA Options Off Large PIP Middle PIP Small PIP and Side by Side Default Off Options Bottom Right Top Left Top Right and Bottom Left Default Bottom Right Options Full screen Pillar Box Letter Box Default Full screen Side by Side Scale Auto Scan Select Source Submenu Options Zoom In Zoom Out Main PIP Default and Return Options On Off Default On Options VGA HDMI1 HDMI2 DVI Video S Video Component Default HDMI Legamaster Audio Settings Menu This menu is used for adjusting volume settings Audio Settings Volume Bass Treble Balance HDMI Audio Input Volume Adjust the sound Press or P select the desired level and then press ENTER Range 0 100 Default 50 Bass Adjust the sound in low tones bass Press d or P select the desired level and then press ENTER Range 0 20 Default 10 Treble Adjust the sound in high tones Treble Press lt or P select the desired level and then press ENTER Range 0 20 Default 10 Balance Adjust the balance of the left and right speakers Press or gt select the desired level and then press ENTER Range 0 20 Default 10 HDMI Audio Input Select HDMI and PC audio input mode Default HDMI 15 Basic Settings Menu This menu is used to make init
8. OSD Language OSD Timeout Sleep Timer Real Time Clock Auto Adjustment Image Position Phase Clock Flesh Tone Front LED IRFM Band rate Monitor ID Light Sensor Factory Reset ADC Mode VGAADC Colibration settings Restore ADC to Default Channel Source z l Resolution Information Firmware Version Description Disabled in Graphics mode Adjust the brightness of the screen Adjust the contrast of the screen Adjust the sharpness of the screen Disabled in Graphics mode Disabled in Graphics mode Adjust the backlight Select the Gamma Select the Color Temp Select the Red Gain Select the Green Gain Select the Blue Gain Select the Red Offset Select the Green Offset Select the Blue Offset Adjust the aspect ratio of the screen Adjust the zoom function Select the Auto scan function Select the main input source Select PIP mode Select PIP location Adjust the aspect ratio of the screen Select the Auto scan function Select the main input source When PIP mode is enable Adjust volume Adjust Bass volume Adjust Treble volume Adjust the balance of the screen SPDIF amp audio input Control Adjust the OSD transparent function Adjust the OSD location Adjust the OSD size Disable in portrait type Adjust the OSD rotation Select the OSD language Select the OSD timeout seconds Select the sleep timer Setup Date amp Time Select Auto adjustment function 0 100 lt 0 100 A according to resolutio
9. 60 90 120 Min Off High Medium Low Off On Off On 115200 38400 19200 9600 1 255 Off On Yes No 12 Legamaster On Screen Display OSD Menu Overview Image settings Main setting Audio Settings Image Settings GE N Audio Settings YE voume Scheme User 4 Brightness Bass Contrast Treble Sharpness Saturation Balance Hue HDMI Audio Input Backlight Color Temperature amp Gamma Image settings continued Basic Settings Image Settings GE Lo Basic Settings LO Gamma 2 2 4 OSD Transparent re OSD Location E Color Temperature S OSD Zoom Off 4 LA OSD Rotation O degree 4 m gr OSD Language English gt 4 f D OSD Timeout Scc 4 Sleep Timer Real Time Clock Display settings PIP Advanced Settings Display Settings GE Advanced Settings JE Main A Aspect Ratio Full Screen gt 4 Zoom 4 Auto Scan gt Flesh Tone Off Front LED Off IRFM Off Baud Rate 115200 Select Source PIP PIP Mode Monitor ID 0 Light Sensor Factory Reset Display settings continued System Status Display Settings UE System Status GE DY Main AL Channel Information 4 Aspect Ratio Full Screen 4 Zoom 4 eS Q Source Resolution Auto Scan gt HDMI1 1024x768 60 0HzZ Select Source VGA 1024x768 60 0Hz PIP PIP Mode Side By Side PIP Position Top Left Aspect Ratio Full Screen Side By Side Scale Firmware Version
10. ADC calibration begins Image in the green boxes displayed on both side of the screen has to be white and black in order to run the calibration accurately the black and white image can be made using software like Microsoft PowerPoint Il The white in the left green box has to be the brightest white Ill The black in the right green box has to be the darkest black Region 1 White Ready to run ADC Calibration MES 3 After proper image is displayed click Yes to begin ADC calibration 4 During calibration process the following image will show to notify user to wait for the calibration User ADC Calibration Please Wait 5 After calibration is completed the display will notify user if the process is done successfully by different messages User ADC Calibration Finish User ADC Calibration Failure 17 8 1 2 10 Touch Operation Connect the signal cable to monitor then turn on computer Connect the USB cable with monitor and computer Turn on the monitor AC switch on Connect one side of USB cable Type B USB connector on the monitor side See below picture Check Connection section for exact location Connect the other side of USB cable Type A USB to the USB port on computer Wait for 5 seconds and the touch function is ready to go It can be activated by pen finger or any other pointer This touch monitor is Microsoft Windows 7 compatible In ord
11. Don t repair or open the monitor by yourself Failure to do so may result in fire or electrical shock Contact your dealer for inspection Protect and correctly use the power cord plug Don t press heavily on the power cord plug Don t step on the power cord plug Before inserting the power plug into the wall outlet connect the power cord to the monitor Don t operate the monitor with a damaged power cord or it may damage the monitor Using the extension cords not recommended If an extension cord must be used ensure the voltage rating exceeds the max power consumption of the monitor if the voltage rating is less than the monitor it will cause the extension cord to overheat Don t use any kind of liquid on the monitor If liquid is spilled on the monitor remove the power and ask an qualified service personnel to check the monitor If the liquid gets on the monitor s screen please clean it with a dry and soft cloth immediately Don t use any harsh chemical on the monitor If metal or liquid gets into the monitor it may cause a fire or an electrical shock Don t install or remove the power plug with wet hands This may cause an electric shock If the monitor will not be used for a long period of time unplug the monitor This may cause premature wear of electrical components or fire Don t push or shake the monitor This may cause damage or injury If the glass of the monitor panel is broken
12. Notice 23 Wall Mount Safety Notes 24 1 Important Safety Instructions Before using the touch monitor please read this user manual thoroughly to help protect against damage to your own and other people s property and ensure your own and other people personal safety Be sure to observe the following instructions For your safety be sure to observe the warnings located in this manual For installation or adjustment please follow this user manual instruction and refer all servicing to qualified service personnel Safety Precautions If smoke or peculiar smell comes from the monitor remove the power plug from the outlet immediately Failure to do so may result in fire or electrical shock Contact your dealer for inspection If the monitor has been turned on but there isn t a picture remove the power plug from the outlet immediately Failure to do so may result in fire or electrical shock Contact your dealer for inspection If water is spilled or objects are dropped inside the monitor remove the power plug from the outlet immediately Failure to do so may result in fire or electrical shock Contact your dealer for inspection If the monitor is dropped or the cabinet is damaged remove the power plug from the outlet immediately Failure to do so may result in fire or electrical shock Contact your dealer for inspection To turn off the power of the monitor press O on the main power switch at side of moni
13. format 450 cd m2 4000 4 5 ms 16 9 Positive Negative Positive Negative HDMI x2 VGA SPDIF DVI PC audio in IR Extender Audio amplifier speaker ready AV Component S V Audio in x2 23 92 KHz Analog 23 92 KHz Digital 56 85 Hz Analog 50 85 Hz Digital Clock Phase H Position and V Position VGA SVGA XGA WXGA HD monitor Full Screen Display WUXGA VESA DPMS English German Dutch French AC 100V 240V lt 273W lt 1W 50 60 Hz AC 100 240V 1307 0mm x 777 8mm x 150 3mm 61 7 x 37 1 x 5 9 56 KG 66 KG Min 20 C Max 60 C Min 0 C Max 35 C 90 RH 40 C DDC 2B Compliance D Sub 9 pin RJ 45 in amp out 7 keys SOURCE gt lt 4 A V MENU EXIT O 400 x600 VESA standard Input 1Vp p Output 10W 4Q x2 Optical Finger gloved hand or any other pointer USB type B female 88 Windows 2000 XP Vista Window 7 multi touch requires driver Mac OS X Linux requires ev touch 20 Legamaster Dimensions Model A B 87 1 150 3 a QU I 388 9 21 11 Troubleshooting Before calling service personnel please check the following chart for a possible cause to the trouble you are experiencing Perform the adjustments according to page 8 Operation The Monitor If the problem you have experienced isn t described below or you can t correct the problem stop using the monitor and call service personnel or your dealer Problem Check these things Ensure the power plu
14. 59 81 75 60 02 75 025 85 024 59 95 59 98 59 901 59 88 59 98 59 954 60 59 93 59 95 29 97 25 60 50 50 59 94 60 50 59 94 59 94 24 30 50 59 94 60 Dot clock MHz 25 175 31 5 31 5 36 36 40 50 49 5 56 25 65 75 78 75 94 5 85 5 64 74 5 95 75 79 5 68 25 117 5 71 83 108 108 135 157 5 101 121 75 88 5 106 5 119 146 25 162 138 5 154 13 5 13 5 27 03 27 74 25 74 176 74 25 74 25 74 176 74 25 74 25 74 25 148 5 148 352 148 5 HDMI O0O0O000000000000000000000000 0000000 O 480i 5761 O OjJO JOJOJOJOJOJO O O O VGA O00000000000000000 0000000000000000 0 O00000 00 O O Component 480i 576i S Video Legamaster Composite DVI O00000000000000000000000000000O0O0OOO O O 480i O 576i O O00000 0 O O 19 10 Specification 1 LCD panel Scan Rate Performance Item Resolution Brightness Contrast Ratio Response time GTG Aspect Ratio Horizontal Sync Vertical Sync Connectors Horizontal Horizontal Auto Adjust Screen Scaling Power Management OSD Language Power Input Operation Mode Power Saving Mode Input Frequency Range Rated Input Volt Dimension WxHxD Net Weight Gross Weight w packing Storage Temperature Operating Temperature Humidity Plug and Play RS232 OSD key Wall mount Speaker Technology Method Interface Transmittance Operating System Legamaster Specification 1920 x 1080 HD monitor
15. cheme Brightness Contrast Sharpness Saturation Hue Backlight Gamma amp Color Temp Main PIP Volume Bass Treble Balance Sub Sub Menu Gamma Color Temp Red Gain Green Gain Blue Gain Red Offset Green Offset Blue Offset Aspect Ratio Zoom Auto Scan Select source PIP mode PIP Position Aspect Ratio Side by Side Scale Auto Scan Select source HDMI Audio Input OSD Transparent OSD Location OSD Zoom OSD Rotation OSD Language OSD Timeout Sleep Timer Real Time Clock Auto Adjustment Image Position Phase Clock Flesh Tone Front LED IRFM Band rate Monitor ID Light Sensor Factory Reset Channel Information Source Resolution Firmware Version Description Disabled in Graphics mode Adjust the brightness of the screen Adjust the contrast of the screen Adjust the sharpness of the screen Disabled in Graphics mode Disabled in Graphics mode Adjust the backlight Select the Gamma Select the Color Temp Select the Red Gain Select the Green Gain Select the Blue Gain Select the Red Offset Select the Green Offset Select the Blue Offset Adjust the aspect ratio of the screen Adjust the zoom function Select the Auto scan function Select the main input source Select PIP mode Select PIP location Adjust the aspect ratio of the screen Select the Auto scan function Select the main input source When PIP mode is enable Adjust volume Adjust Bass volume Adjust Treble v
16. cts the S Video source OSD Key Pad function List _ HD 5SDI2____Notavailable at this model 7 SWAP Swaps the main source amp sub source picture Key Description 8 P SOURCE Selects the secondary sub source Power Power on Power off 9 MENU Opens the monitor s on screen menu system Source Source selection toggle When the menu system is already open gt Menu Right Volume pressing this button will select the a gt O rin previous submenu SA A 4 VY Navigates through submenus and settings A Men UU 10 EXIT Closes the menu system i ER UU 11 ENTER Selects highlighted menu choices _Menu extt____ MenufExitselection_______ 12 SCALING Toggles between different aspect ratios Auto Native 4x3 16x9 16x10 and Letterbox FREEZE Freezes the current source image MUTE Turns off the sound BRIGHT Adjusts the brightness JE CONTRAST Adjusts the contrast AUTO Synchronizes the monitor to the source Legamaster SOURCE Allows selection We make communication visible Power ON Stand by Indicator of the different Remote Control POMERS Receiver VOLUME Decreases the sound volume VOLUME Increases the a A lt A z Power Status Condition N Green Power on Orange Power off Power saving mode Select LED on via menu Front LED On Off AC off Power on Select LED on via menu Front LED Off SCALING FREEZE MUTE HOT KEY BRIGHT CONTRAST AUTO LED OFF OSD Menu Lock Unlock Control hy Cy CO The LED turn completely off when in the off
17. emote or side control panel to put the monitor in a standby mode To turn off power completely turn the AC switch to O or disconnect the AC power cord from the power outlet NOTE If there is no signal input for a period of time the monitor will automatically go to standby mode Adjusting the Volume 1 Using the remote press the VOLUME or VOLUME to increase or decrease the volume 2 Press the MUTE button to temporarily turn off all sound To restore the sound press the MUTE button again Selecting the input source 1 Using the remote press the desired source button VGA HDMI1 HDMI2 COMP VIDEO or S V 2 Or press SOURCE on the monitor keypad use the arrow buttons A W to navigate to the desired input source and press ENTER HDMI 1 HDMI 2 VGA Component S Video Composite Video DVI 3 When the monitor cannot find a source a No signal message will appear 1010 PIP mode 1 Select the main source Using the remote press the desired source button VGA HDMI1 HDMI2 COMP VIDEO or S V 2 Turn on PIP Using the remote press PIP Large PIP Middle PIP Small PIP 3 To select the PIP sub source Using the remote press P SOURCE and use the arrow buttons A W to navigate to the desired sub source Press ENTER 4 To change the size and position of the sub source Using the remote press P POSITION to toggle through the options Top Left Top Right Bottom Left
18. er to activate go to http www nextwindow com nextwindow_support windriver html to download the latest driver Follow the direction in the NW Multitouch Device Driver Installation Guide part of the compressed file along with the driver to install the driver Once the driver is installed restart the PC and the touch function is ready to go with MS Windows 7 Operating Systems Supported I Microsoft Windows i Windows 2000 XP Vista and 7 Plug and play ii Driver required to run dual touch gesture on Windows 7 works as a digitizer Il Mac OS Plug and Play Single touch only Ill Linux Supports Knoppix based on Debian distribution with the following requirements i Linux 2 6 kernel series ii Evtouch Touchscreen Driver http www conan de touchscreen evtouch html ili Single touch only 4 Point Calibration Procedure Note no calibration is required for first time use however the touch panel might be required for calibration over time depends on the usage Press the CAL button located next to the USB connector see page 8 item 4 for location or press the Scroll Lock key on the keyboard 6 times Touch USB as A maan Legamaster Il Wait for the beep sound and the cursor will move to near the upper left corner of the display automatically Ill Place finger gloved hand or any other pointer on the cursor and stay for 2 seconds a beep sound will occur when the pointer is placed on t
19. g is installed correctly on both ends Check the main power switch is set to Check that source equipment is operating correctly Check the input signal is compatible with this display No Display The image is not centered Check the input signal is compatible with this display The image is Check the input signal is compatible not locked correctly with this display Make sure the batteries fresh and are installed correctly Ensure the remote is aimed at the IR sensor on the front of the display The remote control doesn t work The picture color looks poor Check the picture settings Reset the display If you are using YUV terminals make sure cables are correctly connected Legamaster FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the quick setup guide and user manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense Warning This is a Cla
20. he cursor Then the cursor will move to near the upper right corner automatically IV Repeat the procedure of item III until all 4 points is calibrated see image below for the places where cursor appears V Confirm by tapping anywhere between the 4 points The calibration is completed and the touch monitor is ready to be used now E Legamaster We make communication visible 18 9 Table supported timings Timing VGA 640x480 SVGA 800x600 XGA 1024x768 WXGA 1360x768 1280 x 720 VESA 1280 x 768 1280 x 800 1152x864 AA 1280x1024 SXGA 1400 x 1050 1440 x 900 WSXGA 1680 x1050 UXGA 1600 x 1200 1920 x 1080 WUXA 1920 x 1200 NTSC PAL 480p 576p 720p 1280x720 SDTV EDTV 1280x720 1280x720 HDTV 1080p 1920x1080 O means that the timing is supported fH kHz 31 469 37 861 37 5 43 269 35 156 37 879 48 077 46 875 53 674 48 363 56 476 60 023 68 677 47 712 44 444 44 772 56 456 47 776 47 396 68 633 49 306 49 702 67 5 63 981 79 976 91 146 64 744 65 317 55 469 55 935 64 674 65 29 75 66 587 74 038 15 734 15 625 31 5 31 25 37 5 44 995 45 28 13 33 16 33 5 27 33 75 56 25 67 433 67 5 480i means that it supports 480i 60Hz YPbPr 576i means that it supports 576i1 60Hz YPbPr fV Hz 59 94 72 809 75 85 008 56 25 60 317 72 188 75 85 06 60 004 70 069 75 029 84 997 60 015 59 98 59 86 74 78 59 87 59 995 84 837 59 91
21. ial set up adjustments to the OSD On Screen Display menu and other on screen messages Basic Settings OSD Transparent OSD Location OSD Zoom Off OSD Rotation OSD Language English O degree OSD Timeout 30 Scc Sleep Timer Off Real Time Clock gt OSD Transparent Set the menu transparency Press or P select the desired level and then press ENTER Range 0 100 Default 0 OSD Location Adjust the menu location on the monitor Up Down Left Right OSD Zoom Options On Off Default Off OSD Rotation Select the OSD Rotation Press lt 4 gt select the rotation Options 0 90 180 270 Default 0 degree OSD Language Options English German Dutch French Default English OSD Timeout Options 5 120 Default 30 Sleep Timer Set a period of time after which the monitor will switch to standby mode automatically Press gt to select the desired time limit Options Off 15 30 45 60 90 120 Min Default Off Real Time Clock Set date and switch alarm on and off Use A V 4 P to adjust these options Legamaster Advanced Settings Menu Advanced Settings Flesh Tone Off Front LED Off IRFM Off Baud Rate 115200 Monitor ID 0 Light Sensor Off Factory Reset NO Auto Adjustment Forces the monitor to reacguire and lock to the input signal This is useful when the signal guality is marginal Note This feature does not continually reacquire the signal Options No Yes Defau
22. image retention Burn in and or image retention is not covered under warranty Make sure to change the image on the monitor periodically It is recommended to turn off the monitor for at least 6 hours after 18 hours of usage in a day to avoid image retention Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to make adequate measures Exemptions This product isn t warranted for any damage caused by natural disaster such as earthquake thunder etc fire acts by third parties accidents owner s intentional misuse and fault or uses in other improper conditions This product isn t warranted for incidental damages such as profit loss or interruption in business modification or erasure of record data etc caused by use or inability to use of this product This product isn t warranted for any damage caused by inappropriate operation or from not following the user manual This product isn t warranted for any damage caused by misuse or malfunction through simultaneous use of this product and the connected equipment or software This product isn t warranted for any damage caused by neglect of the instructions described about installation This product isn t warranted for any damage caused by improper installation This product isn t warranted for any damage caused by disassembly modification or repair by
23. liquid may escape Please don t touch the liquid If liquid get into your eyes or touches your skin wash with the clean water and seek medical attention immediately Precautions with the remote control batteries Please only use approved AAA type batteries Please be sure to insert batteries by matching the and Don t recharge heat disassemble short or throw batteries into a fire Don t mix a new battery with a used one Don t mix different types of batteries together only use the specified type Or it may cause burn and injury Legamaster Cleaning If dust has collected on the power plug removed the plug from the outlet and clean off the dust Dust build up may cause a fire Take off the power plug before cleaning Failure to do so may result in electrical shock or damage Cleaning the surface of the monitor When the surface of the monitor becomes dirty please wipe the surface lightly with a soft clean cloth If the surface requires additional cleaning lightly moisten the cloth with rubbing alcohol Do not to let alcohol enter the monitor as it may cause electrical shock or damage 2 Warning For Use Use Do not use this touch monitor on the ground Transport the monitor upright with proper packaging Avoid placing the monitor face up or down Be careful not to bump to the monitor Do not send a static non moving image this monitor or it may cause image burn in or
24. ll outlet Set the LCD Monitor box in an upright position and open from the top of the box before removing the top cushions Step 1 Remove the white handle and cut the banding Power Cord black A O OON carton Lock gt E Y OSD Remote Control 2 piece batteries AAA inside USB Cable Ergonomic stylus Q ty 1 set 1 pcs 1 pcs 1 pcs 1 pcs 1 pcs 2 pcs 1 pcs 1 pcs 1 set 6 pcs Legamaster 5 Installation 1 Environmental state Signal Source Input Operating temperature 5 C 35 C Fahrenheit 41 F 95 F Humidity 85 RH Max Input Interface Name Connecter p t 1 HDMI 1 input x 1 ower inpu p 2 HDMI 2 input x 1 Power Cord 3 DVI D input x1 D Sub 24 pin The included power cord is used to connect the side controls of 4 VGA D Sub 15 pin the LCD monitor and the wall outlet 5 PCaudioin Mini jack Connect the power cord into main power of the monitor _ is power on O is power off 6 5 PDIF out 7 RS232C D Sub 9 pin Input 100 240V 5A 50 60H e BA Ka t gt k 9 RS485 Out RJ 45 a is power on 10 Component RCA G B R O is power off 11 Audio In Component RCA L R mm The side 12 S Video mini Din 4 pin y controls Ma X A ji 13 Video RCA pe ai 14 Audio in S Video Video RCA L R 15 AC in connector O OL main power switch 16 AC out connector IEC C13 AC in socket AC outsocket 17 Power switch ON OFF O 18 Touch USB Type B female 3
25. lt No Image Position Image location can be adjusted Only VGA Mode Options Up Down Left Right Phase Range 0 63 Only VGA Mode Clocks Range 0 100 Only VGA Mode Flesh Tone Options Off Low Medium and High Only Video Mode Default Off Front LED Options On and Off Default On IRFM Creates slight frame motion to help avoid image retention Options On Default Off Baud Rate Options 115200 38400 19200 9600 Default 115200 Monitor ID Options 1 255 Default 0 Light Sensor Options On and Off Default Off Factory Reset Restores all settings to their default Options No Yes Default No VGA ADC Settings Select ADC setting User ADC Calibration and restore factory default ADC setting Options Default User Default Default 16 Legamaster System Status Menu Item Default Value This read only menu provides information on the active sources Power switch Off and the latest firmware version Brightness 50 Backlight 80 System Status Ge Contrast 50 Color Temp 9300 K RS Source Auto Detection Off Source Resolution OSD Language English HDMI1 1024x768 60 0 HZ Aut O Off VGA 1024x768 60 0 y Monitor ID 01 IRFM Off Baud rate115200 Firmware Version 1 When using VGA as signal source go to Advanced Settings in OSD menu and select VGA ADC Settings then choose User ADC Calibration 2 A warning message see image below will show to make sure proper image is displayed on screen before
26. mode regardless SOURCE NE TE VOLUME of the monitor being on or off Lock Press Enter Enter Exit Exit Enter and Exit on the controller by sequence and OSD will be locked Unlock Press Enter Enter Exit QE Exit Enter and Exit on the controller by sequence and OSD will be unlocked Change the RCU Battery 1 Insert the batteries Close the battery cover Remove the battery cover Slide back and remove the battery cover in the direction of the arrow Align and insert two AAA batteries according to their plus and minus ports as indicated in the remote control Replace the battery cover in the direction of the arrow and snap it back into place Used batteries needed to follow the city rule to be discarded Avoid keeping used old batteries inside the remote control causing leakage of internal liquid resulting metal rust or fatal damage to the remote control hand unit Battery to be used according to the instruction CAUTION Don t drop shake or bump Don t place on wet materials Don t dismantle Don t place in locations with exposure to high temperature or high humidity levels Legamaster Display Mode Turning the monitor on 1 Correctly insert the power cord into monitor and into the power outlet 2 Ensure the AC switch is set to 3 Press the power button on the remote or side control panel Turning the monitor off With the power on press the power button on the r
27. n Vv according to resolution According to resolution According to resolution Disabled in Graphics mode Select the front LED function Select the anti burn in mode function Setting the band rate of monitor Setting the ID of monitor Select light sensor function Reset to the factory default setting Select ADC setting Execute User ADC Calibration Restore User ADC setting to factory ADC default Show the name of input source Show the current resolution Show the firmware of the monitor Legamaster Setting 0 100 0 100 0 24 0 100 2 2 Off 5000K 6500K 7500K 9300K User 128 384 128 384 128 384 50 50 50 50 50 50 Full Screen Native Letter Box Pillar Box gt lt Off On VGA HDMI1 2 DVI Video S V Component Off Large PIP Medium PIP Small PIP Side by Side Bottom Right Top Left Top Right Bottom Left Full Screen Native Letter Box Pillar Box PIP 4 Main A Zoom IN Y Zoom Out Off On VGA HDMI 1 2 DVI Video S V Component 0 100 0 20 0 20 0 20 HDMI PC 0 100 yl AV Off On 0 90 180 270 English German Dutch French 5 120 sec Off 15 30 60 90 120 Min Off On Off On Off On 115200 38400 19200 9600 1 255 Off On Yes No Default User 11 Video Mode Main Menu Image Settings Display Settings Display Settings Audio Settings Basic Settings Advanced Settings System Status Sub Menu S
28. non authorized service center or people Legamaster Features High resolution Full HD 120Hz panel This monitor supports a 1920 x 1080 HDTV format and can display true 1 073G colors Full array of PID connectivity Video system Input HDMI x2 COMPONENT RCA x1 VIDEO RCA x1 S VIDEO Mini Din 4 pin x1 RGB Input PC VGA D Sub 15pin x1 PC DVI D sub 24 pin x1 Communication RS 232C in D sub 9pin RS 485 in out Other functions High color saturation 2 HDMI v1 3 inputs with HDCP SPDIF output Signal source auto detection OSD keypad lock function PIP PBP function Please see the chapter Display mode Overscan function Supports input main sub source detection Legamaster 4 Package i Unpacking Step 2 Remove the top cushion and take the accessories Bag out Aljm HRl WIN PALLET SHEET SIZE A4 210mmX297mm BAND Item e Screen 55 Carton Bottom cushion Top cushion Packing bag Accessories Bag Remote control Batteries Power cord D SUB 15pin cable Ergonomic stylus Carton lock Contents of the Accessory Bag The e Screen 55 is packed in a carton box and may be banded VGA Cable D sub to 2 types of custom pallet depends on the number of units shipped The e Screen 55 is packed using cushions to protect the monitor during shipping Before unpacking your monitor prepare a stable level and clean surface near a wa
29. olume Adjust the balance of the screen SPDIF amp audio input Control Adjust the OSD transparent function Adjust the OSD location Adjust the OSD size Disable in portrait type Adjust the OSD rotation Select the OSD language Select the OSD timeout seconds Select the sleep timer Setup Date amp Time Disabled if not a VGA mode Disabled if not a VGA mode Disabled if not a VGA mode Disabled if not a VGA mode Select the flesh tone setting Select the front LED function Select the anti burn in mode function Setting the band rate of monitor Setting the ID of monitor Select light sensor function Reset to the factory default setting Show the name of input source Show the current resolution Show the firmware of the monitor Legamaster Setting User Vivid Cinema Game Sport 0 100 0 100 0 24 0 100 0 100 0 100 2 2 Off 5000K 6500K 7500K 9300K User 128 384 128 384 128 384 50 50 50 50 50 50 Full screen Pillar Box Letter Box Native gt lt Off On VGA HDMI1 2 DVI Video S V Component SDI 1 2 Off Large PIP Medium PIP Small PIP Side by Side Bottom Right Top Left Top Right Bottom Left Full screen Pillar Box Letter Box PIP 4 Main A Zoom IN Y Zoom Out Off On VGA HDMI1 2 DVI Video S V Component SDI 1 2 0 100 0 20 0 20 0 20 HDMI PC 0 100 yl AV Off On 0 90 180 270 English German Dutch French 5 120 sec Off 15 30
30. ric shock Don t overload outlets or cables beyond electrical capacity Don t use extension cords as it may cause a fire or electric shock Don t insert the power plug into an outlet other than 100 240V AC This may cause a fire or electric shock Don t use a damaged power plug or worn outlet Don t insert the improper power plug it may cause a fire and electric shock Don t place the touch monitor on an unstable shelf or surface The monitor may fall causing injury Please install on a horizontal stable level surface Don t place objects on the touch monitor f the touch monitor is covered or the vents are blocked the monitor could overheat and cause a fire If metal or liquid gets into the monitor it may cause a fire or an electrical shock Do not put heavy objects on the monitor as it may fall causing injury Please keep a 10 cm minimum distance between the monitor and the wall for sufficient ventilation Don t move the touch monitor when it is connected to the power cord and AV cables When moving the monitor make sure to remove the power plug and cables from the outlet or source When unpacking or carrying the monitor at least 2 people are needed Make sure the monitor is carried upright Transport the monitor upright Avoid placing the monitor face up or down Handle the monitor gently Do not drop Use If you encounter a problem during installation please contact your dealer for assistance
31. ss A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation EN 55022 EN 61000 3 2_EN 61000 3 3 EN 55024_1EC61000 4 EN 60950 Low Voltage Directive 73 23 EEC Information in this document is subject to change without notice 2011 Legamaster International B V All rights reserved Reproduction in any manner whatsoever without the written permission of Legamaster International is strictly forbidden Trademarks used in this text Legamaster and the Legamaster logo are trademarks of edding AG Windows is a registered trademark of Microsoft Corporation Nextwindow is a registered trademark of Nextwindow Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Legamaster International disclaims any proprietary interest in trademarks and trade names other than its own 22 13 Appendix Moving and Carrying Notice Moving Notice Moving the monitor requires at least two people If not it may drop and a serious injury may result Moving shipping the monitor please hold the white handles
32. tor The power standby on indicator will go off and the monitor cannot to be turned on off by using the POWER button on the remote control To turn on off the monitor by the remote control press the main power switch again and light the power standby on indicator When turning off the monitor by pressing the POWER button on the remote control the main power of the monitor is not turned off completely To disconnect the monitor completely from power supply remove the power plug from the outlet Press O to turn off the monitor completely If the power cord or plug is damaged or becomes hot turn off the main power switch of the monitor make sure the power plug has cooled down and remove the power plug from the outlet If the monitor is still used in this condition it may cause a fire or an electrical shock Contact your dealer for replacement Legamaster Installation when installing the monitor please follow the instructions in the user manual Don t install in a high temperature environment If the monitor is used in high temperature or in direct sunlight it may cause the case or other parts become distorted or damaged resulting in overheating or electric shock Don t install in a high humidity environment This may cause overheating or electric shock Don t install near any heat sources such as radiators heat registers stoves or other apparatus that produce heat This may cause a fire or elect
Download Pdf Manuals
Related Search