Operating- and maintenance manual Red Dragon
Contents
1. as inlet this has to fulfil the requirements of a suction pipe It is very important that the initial inlet at the pump is straight Minimum distance of 3 5 x the diameter of the inlet pipes from the housing to the first bow In this way the efficiency factor is maximized because the water enters laminary at the impeller see next page For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 Since 1986 info royal exclusiv de www royal exclusiv de KKKKK 5 4 Pressure pipe pump outlet The pressure pipe has to have the same diameter as the intake of the pump in order to minimize pressure loss high flow rates and noise The best thing is if you enlarge the pressure pipe directly after the pump oulet in order to ma ximize the pump capacity and to safe energy Reduce is feasible in small groups Maximum 1 size smaller For example from 40 mm to 32 mm or 32 mm to 25 mm If the inlet piping is longer than gt 10 or the suction head is higher than 1 m the inlet piping has to be 1 or 2 sizes larges than the intake of the pump Outlet pipe dimensions Model 50 W min 25 mm Model 80 Watt min 32 mm X V Always use bows instead of2. of charge for products which were brought into circulation after the 13th of August 2005 We will take care for the disposal If a customer chooses not to let us take care for the disposal he takes the responsibility of a disposal according to legal regulations and discharges us from our liabilities according to 10 sect 2 ElektroG and any associated liabilities of others 4 Subject to alterations The manufacture has the right for changes in hardware and software of the product at any time without preliminary no tice as long as these changes advance reliability or quality of the pump No claims can be made if for instance design functionality or performance of the pump changes elemen tary The assured specification of the pump is always guar anteed Pince 1956 Kk kkk 2 CE Manufacturer s declaration The manufacturer assures that the products of the Red Dragon 3 Speedy series comply with the following EWG directives when installed and uses according to this manual Machinery Directive 98 37 EG Electromagnetic compatibility 89 336 EEC 73 23 EWG 95 EN ISO 12100 Safety of machinery EN 61000 6 2 Electromagnetic compatibility EN 61000 6 3 Electromagnetic compatibility EMC Specification for safety of household and similar electrical appliances Household and similar electrical appliances Particular requirements for pumps Specification for safety of household and similar electrical appliances Part
3. used improperly or not For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de regarding to its designated use or if safety advises are ignored If the pump is used improperly the liability of the manufac turer and the operating permit are void For safety reasons children and juveniles younger than 16 years as well as people who do not recognize possible risks or who are not familiar with this manual may not use the device Please preserve this manual carefully In the case of a dis posal please hand over the complete manual The combination of water and electricity can be a serious threat to life and limb when not installed according to di rections or when used improperly Only use the device when no body parts have contact to the water Before you reach into the water always disconnect the pump from the power supply Compare the electrical specification on the type label of the de vice with the specification of the power supply Make sure that the device is connected to an ELCB earth leakage circuit breaker with an assigned leakage rat ing of max 30 mA DIN VDE 0100T739 Only operate the dev
4. Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 Since 1986 info royal exclusiv de www royal exclusiv de KKKKK Operating and maintenance manual Red Dragon 3 pumps For all Red Dragon 3 skimmer filter and flow pumps with and without controller Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 Since 1986 info royal exclusiv de www royal exclusiv de KKKKK Operating and maintenance manual Red Dragon 3 pumps For all Red Dragon 3 skimmer filter and flow pumps with and without controller 1 Defects and claims for compensation disclaimer a cvcceeeteeeeeeeeeteeteeeeeeteees 2 2 CE Manufacturer s declaration neat te eeteeeeeeeeeeeeeeseeeaeees 3 2 1 Manufacturer gg qj i N iain catenin eiatlnionse 3 2 2 Formal obligation beer steepness sane eens 4 3 Quick installation RD3 Speedy with speed regulation aac eaeccceeeteeeteeeeaeeeeeeeaeeees 4 3 1 Quick installation guide RD3 Freshwater without speed regulation eee 4 3 2 Quick installation guide RD3 MiniSpeedy MiniSpeedy BK skimmer pumps with speed regulation oa eecceececeeeeeeeeeeeeees 4 4 Improper usage ett te cece eeseece eee eeeeeeeeees 4 4 1 Applications etc ne cece eee eeeeeeeeeeeeaeeeees 6 SRUNI iit teectezcn ececcectenaneesee 6 Sele OM CNCG eects 6 Dies PU ae intr rtertceti cn de
5. e he is obliged to thoroughly the Suitability of the product for the other purposes We give no warranty and no liability accrues for any applications that are not agreed on by us explicitly and in written form Any manipulation of the pump the impeller or the electronic as well as any attempt to modify the software to influence the software or to read out or re engineer the software of the driver unit immediately causes a loss of warranty and all claims and rights expire We point out that the controller software is protected by security mechanism Any attempt to read out the software will instantly result in the execution of a data erasing program The software of the pump then is deleted and has to be recovered by the manufacturer Every user is held responsible for the appropriate usage of his Red Dragon 3 pump The user manual does not discharge you from your liability for a safe appropriate and secure application installation operation and maintenance By using this manual you agree that in no circumstances the manufacturer can or will be held liable for any personal injuries or property damages which possibly occur due to the usage of the device This applies specifically for any damages that are due to inappropriate piping or plumbing Insufficient or missing cleaning or maintenance intervals and damages that might result due to these are not cov ered by warranty This applies especially for calcinations salt water usage and accum
6. eases the revolution of the pump Thus the flow rate and the energy consump tion decrease The revolution can be chosen in 5W steps from 15 50W 8OW The pump runs always on the configured speed Notice When you press the buttons on a skimmer pump itis the display active After 2 3 seconds the display switches to the effective power mode Brushless Motor Controller 7 Maintenance and cleaning of the RD3 Mini Speedy Speedy and Freshwater pumps Disconnect the pump from the power supply prior to each maintenance work Red Dragon supply and flow pumps are essentially to be classified as low maintenance Usu ally the necessary maintenance work is limited to a check of the impellor for obstruction Remove obstacles from the impellor with a slim and spiky tool A decreasing supply rate is often the result of dirt Possible calcinations especially in saltwater applications has to be removed with a very soft acid as for instance vinegar Avoid applying pressure to the sides of the impellor or the rotor The pump can be disas sembled nearly completely for cleaning In freshwater and saltwater applications calcification only appears in very hard water and after a complete re filling of the pond After this the largest amount of carbonate will be omitted within 2 3 days To dismount the pumps head from the engine unscrew the M5 hexagon socket titanium screws with a matching span For more information please visit www royal exc
7. elbows P P max x 10 E BES Inlet piping dimensions Model 50 W min 40mm Model 80 W min 50mm a bypass has to be installed in the pressure pipe so that always a minimal flow of If there is a danger that the pressure pipe gets completely blocked e g by a ball valve V water trough the pump is guaranteed V For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 5 5 Electrical connection setting up operation Check whether voltage and frequency on the type label of the pump match the supply voltage The person respon sible for the installation has to check whether a standard conform grounding is available It is necessary to check if the electrical installation has a highly sensitive earth leakage circuit breaker ELCB GFCl is available 30mA DIN VDE 0100T 739 The fuse for the electrical net has to be one level high then the fuse of the pump lightning main min 4A Fuse dimensions up to 80 Watt pump min 2A 5 6 Overload protection The RD 3 Pumps have an electronic and electric overload protection If the rotor gets blocked the motor i
8. es Yes reducing ring 32 mm Nozzle with ozone amp air plug 4 kg 2 Years Speed variable 400 4000 1 min Noise level The noise level is beneath the levels of the benchmark of the machine directive of the European Council partly below 32dB measured in an outdoor setting 1 meter And now we wish you much pleasure with your Red Dragon 3 pump A regular maintenance guarantees a long running and thus life Royal Exclusiv in December 2013 For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved
9. ice on a correctly installed power plug Keep the power plug and the wiring dry Install the wiring protected in order to avoid damages IT IS NOT ALLOWD TO CUT THE WIRING OR THE POW ER PLUG DOING SO WILL IMMIDEIATLY VOID ALL WARRANTY AND LIABILITY OF THE MANUFACTURER Only use wiring installations adapters extension cables and connection cables with grounding typ plugs which are approved for outdoor usage DIN VDE 0620 with suf ficient cable diameter Do not pull on the wiring of the de vice and to not use the wiring to carry the device If the wiring is damaged or broken the device may no longer be used Reparation is not possible as the wiring is perma nently grouted in the engine housing Take care that the power plug never falls into water or gets wet If the plug gets wet in any kind it has to be opened by a professional and cleaned by purging with demineralised water Protect the plug and the wiring against heat oil UV light and sharp corners The manufacturer is not liable in any way for any damages which are made by improper installation or by the carelessness of the user or installer In general when put out of service the pump has to be cleaned extremely thoroughly Before it newly brought into service the ease of movement of the impellor has to be checked by hand If the impellor cannot be moved round by hand the pump needs to be disassembled and cleaned Pince 1956 Kk kkk completely It is forbidden to di
10. icular require ments for appliances for use with aquariums and garden ponds Household and similar electrical appliances Electromagnetic fields Methods for evaluation and measurement Electromagnetic compatibility Requirements for household appliances electric tools and similar apparatus Emission Electromagnetic compatibility Requirements for household appliances electric tools and similar apparatus Immunity Product family standard EN 60335 1 2002 EN 60335 2 41 2003 EN 60335 2 55 2003 EN 50366 2003 EN 55014 1 2006 EN 55014 2 1997 2 1 Manufacturer Royal Exclusiv pumps amp skimmer Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de Made in Germany Royal Exclusiv EAR number WEE Reg Nr 83082352 For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 2 2 Formal obligation All Red Dragon 3 pumps are made in Germany The die casting tools were made in Germany The die casted parts originate from German production The assembly the cast ing of the stator and the final
11. ims based upon the malicious concealment of damages from the injury of life health or body and for other damages that result out of intention or wanton negligence For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 1 7 If it becomes apparent during our examination of dam ages reported by the customer or in the course of our re moval of defects that the reported damages or claims were made wantonly negligent or unwarranted we may charge an adequate consideration for our examination and for the removal of defects The customer has the right to neglect a necessary repairing and to demand the return of the pump In general every examination of damages is bound to lump sum compensation if it occurs that the customer has to be accounted for the damages 2 Spare parts Our liability to deliver and hold spare parts available is limit ed to the period of 5 years after initial shipment of the prod uct Our respective list prices apply for spare parts 3 Disposal We offer our customers to take back products that fall under the restriction of hazardous substances directive ElektroG within Germany free
12. in the display F1 F2 Init error start communication F4 Dry Run Error F6 Over Temperature motor driver F8 Air Feeding error skimmer only Skimmer pump P3 P1 50W MiniSpeedy P2 80W Speedy P3 Skimmer pump with 50W motor For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 8 Error table Error 1 The pump does not deliver water the engine does not turn The display is not lit 2 The pump does not supply water the engine is turning 3 The pump delivers irregularly a limited amount of water 4 Irregular operation Possible cause 1 Insufficient voltage from the power supply 2 Plug not adjusted correctly 3 Connection pump electronic faulty 4 ELCB has triggered 5 impeller blocked 6 pump electronic or engine defective 7 pump safety electronic switches the pump off 1 The pump aspirates air 2 An air bubble is in the pump housing 3 The pump faces too much pressure on the outlet 4 The pump is not filled with water 5 The intake or the backpressure valve is blocked 6 The delivery height is too high 1 See error 2 2 Impeller worn out o
13. inspection and testing of the Red Dragon 3 pumps is done in Germany Essential parts of the pumps originate from non German or near European production Titanium parts are made out of saltwater resistant pure titanium grade 2 All plastic parts are made from ozone and UV resistant material The wiring is saltwater resistant excluded Freshwater The stator casing the raw mantle and the bearing rings are made from saltwater resistant ti tanium grade 2 excluded Freshwater The parabolic rub ber feet are made from 30 shore soft saltwater resistant natural rubber 3 Quick installation RD3 Speedy with speed regulation The pump has a DC motor and therefore is equipped with a driver unit The Red Dragon 3 Speedy pumps may only be operated with an ELCB earth leakage circuit breaker Important Electrical grounding of the wiring of the Red Dragon 3 pumps is absolutely mandatory Bridge circuits or grounding over neutral conductor are not permitted and might cause inductive fault current up to 50 Volt Setting up operation has to take place in the following order 1 Thoroughly purge the pump to remove the disinfectant Place the pump below the water level The pump is not regenerative 3 Insert power plug Caution The electrical socket needs to be grounded 4 Keep hole of the pump during the test run Danger of blowback 5 The pump starts immedialty softstart 6 Use the buttons red triangles to adjust
14. lusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de ner When this is done the whole pumps head can be re moved necessary the impeller unit can be removed by cautiously pulling on the rotor with When you pull on the rotor be very careful as the impellor is held in its position by the magnet If you release the rotor while trying to pull it out the bearing can get a serious damage Use fitting hexagon key to loosen the 4 screws from the case Do not underestimate the power of the magnet If you slightly losse the grip and the axis hits the rear bearing the risk to damage the bearing is very high A damage bearing causes high reparation costs Grab rotor and and cautiously pull out completely Check parts for calcification After maintenance you can assemble the pump in re versed order Please pay attention to first only loosely fix the in crossed over order and then fix them semi solid hand tight For the usage of a cordless screwdriver see the picture The O seals of the pump are made from silicone or ERDM Viton depending on the application Please use only fresh and original O seals with the correct thickness and hardnes
15. max 50 C Max working pressure 2bar 20m head of water 5 Fitting Caution Before you install the pump you have to read the manual thoroughly Damages which are caused because the man ual was not read thoroughly do not fall under warranty When unpacking the pump check whether all parts were delivered completely and undamaged Detected damages have to be reported within 8 days after the purchase of the pump at your retail location When unpacking the pump it is possible that the inside of the pump is wet The pump is tested before it leaves the factory Prior to its packaging the pump is treated with a biode gradable disinfectant in order to neutralize possibly pres ent bacteria The pump therefore has to be purged with water thoroughly before usage Please check the pump for damages before you set it into operation Should the pump have damages it may not be set into operation Please inform your retailer immediately Pince 1956 Kk kkk if the pump is set into operation even though it is dam aged any warranty and liability is void Pull the plug electrical socket and make sure that the pump cannot be switch on During the course of the installation the pump may not be connected to the power supply To avoid injuries take care to not reach into opening of the pump with your hands or fingers when the pump is con nected to the power supply 5 1 Controller The controller may not be used outdoors It is
16. only ap proved for indoor usage Furthermore the controller may not be opposed to direct sunlight or direct heat sources powerful lamps central heating etc Adequate air venti lation has to be assured Therefore a minimal distance of 10cm to each side from the next cabinet shelve has to be assured An adequate air ventilation of the room has to be assured For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 5 2 Pump The pump may be used in almost any position However it hast so stand stable on a solid base The inlet pipe is con nected to the suction side of the pump 1 It has to be assured that the pump can be de aerated trough the outlet 2 2 2 The pump should ideally be placed beneath the water le vel 3 The pump can be placed submersed 4 or out of the water dry 5 In the case of a dry placement adequate air ventilation has to be assured Furthermore the pump may not be exposed to direct sunlight Place the pump as close as possible to the actual water connection hence the inlet piping has to be as short as possible Pince 1956 Kk kkk If the pump is placed above
17. or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 9 Technical data Model Voltage Wattage P1 External controller IP68 Length of wiring Digital display Pump fully submersible and dry Inlet dimension Outlet dimensions Weight Warranty Revolution Model Voltage Wattage P1 External controller IP68 Length of wiring Digital display Pump fully submersible and dry Inlet dimension Outlet dimensions Weight Warranty Revolution For further details see type label RD3 Freshwater 100 Watt 9000 L h 110 230 Volt 50 60 Hz 100 Watt No Yes 10m outdoors No Yes Yes min 50 mm pipe min 32 mm pipe 4 5 kg 2 Years Non adjustable 3000 1 min RD3 MiniSpeedy 50 Watt 5000 L h 110 230 Volt 50 60 Hz 50 Watt Yes Yes 3 8m Yes Yes Yes min 40 mm pipe min 25 mm pipe 4 kg 2 Years Speed variable 400 4000 1 min ince 1956 Kk kkk RD3 Speedy 80 Watt 8000 L h 110 230 Volt 50 60 Hz 80 Watt Yes Yes 3 8m Yes Yes Yes min 50 mm pipe min 32 mm pipe 4 5 kg 2 Years Speed variable 300 3000 1 min RD3 MiniSpeedy 50 Watt BubbleKing 110 230 Volt 50 60 Hz 50 Watt Yes Yes 3 8m Yes Y
18. r damaged 3 electronics overheated 4 engine speed set to low 1 solid parts particles block the free turning of the rotor 2 voltage out of tolerance 3 damages on the magnetic rotor or on the engine 4 actual power exceeds 50 80 W Pince 1956 Kk kkk Action 1 3 Check if the correct voltage is supplied and whether all plugs are adjusted correctly 4 Switch on ELCB fit switches off again something is possibly blocking the impeller 5 Clean impeller from possible blockages It is possible that you have to pull out the magnetic runner in order to perform the cleaning 6 Contact customer service 7 The engine reports an error Check the inlet side and the pumpe housing for obstructions blockages 1 2 Retry for a couple of times or fill the pump intake with water Remove the blockage or other 3 Resistance in the outlet ball valves closed 4 5 Check 6 Contact customer service 1 See error 2 2 Contact customer service 3 Insufficient air circulation at the housing e g if it is fitted into a closet it is exposed to direct sun light or the ambient temperature is too high Inlet not OK 4 Increase engine speed to max 1 Remove blocking particles 2 Supply voltage as indicated on the type label 3 Contact customer service 4 Reduce engine speed until the actual power reaches max 50 80 W For more information please visit www royal exclusiv de Simply enter the part number
19. r the consequences of inappropriate application usage maintenance and han dling of the product by the customer or his subsidiaries neither for normal abrasion This applies specifically to the consequences of thermal chemical electrochemical or electrical influences as well as for infringements against our uses and maintenance manuals The same applies to damages which are the result of changes or adjustments by the customer which have not been approved by us in beforehand 1 5 Our liability for wanton negligence is limited to claims of injury of life body and health to claims based upon the law on product liability and to claims from culpable fundamental breach of the contract which peril contractual obligations For the rest our liabilities for wantonly negligent breach of contractual obligations which are foreseeable at the time of the conclusion of the contract are barred Damages which are unambiguously attributed to inappro priate usage of the product are in general to be accounted for by the customer In the case of returns of the product the customer has to use break proof packaging for the product The customer is liable for any damages that can be ac counted to an inappropriate packaging 1 6 Claims against us become time barred within a year after the initial delivery of the goods to the customer The same applies to claims for damages regardless of their ju ridical cause The limitation period does not apply to cla
20. rcctersosiccs T 5 3 Inlet pipe O EEC OLAOAARADEEREDECREDECEED EEEn Ennen 5 4 Pressure pipe pump outlet nec tet eect eeeeeeaeeteeeaaeeees 8 5 5 Electrical connection setting up operation aanasaararnerarnerrrnerrrnenernenere 9 5 6 Overload protection neat eee etete eet eeeaeeeeeeaeenaes 9 5 7 Turning the head of the RD3 MiniSpeedy Speedy Freshwater pumps with and without turnable bypaSS vette tec eeeeeeeeeeeeeeeeeaeees 9 6 Operation of the RD3 pumps with controller innate teteeeeteeeeeeeeeeeneeeeees 9 7 Maintenance cleaning of RD3 MiniSpeedy Speedy Freshwater PUMPG ccc0ccccccceeeees 9 7 1 Decalcification cleaning and assembly of the RD3 MiniSpeedy Speedy and Freshwater PUMPS ____ikacccccsececcceeeeeeteseeeeeees 10 7 2 Power outages and emergency power Supply hae aeccaeeteeeeeeteeeseeeeeeeeees 10 7 3 Meaning of the codes inthe display eee eetaeeeaeeeseeeseeeeeeeeaes 10 8 Error table ii itnienccccicrssreceereaentsencss 11 9 Technical data C ipsiieeainrreit eee Reaialtnm Er n 12 Important Notice Please read this manual carefully before you install the device We recommend not to proceed the installation of the device until you read the manual This prevents any questions and problems that might occur in installation process As soon as you power on the pump for the first time you agree that you read and understood this manual In doubt or if anything is unclear please contact your s
21. s as replacement When O seals are aging the hardness slightly changes When you re as semble the pump the O seals should always be replaced by new ones This will increase the lifespan of the pump Silicone and EPDM Viton O seals are resistant against acids and bases Pince 1956 Kk kkk 7 1 Decalcification cleaning and assembly of the RD3 MiniSpeedy Speedy and Freshwater pumps Decalcify the pump completely Please do not use hy drochloric acid not even in extenuated form This may damage the pump beyond repair After the decalcification purge the pump with clear water Re assemble the pump Very important Tighten the screws loosely crossed over and the fix them semi solidly hand tight Attention The 80 Watt RD3 hast an additional axial floating bearing on the rear shaft Remove this bearing in the case of cal cification cautiously and decalcify seperatly The bearing has to be installed on the axis before the pump is re as sembled The bearing needs to be fixated before assem bly as seen on the third picture The axial bearing is not compulsory and only serves to avoid radial run outs while restarting the pump 7 2 Power outages and emergency power supply After a blackout the pump will start automatically and the controller will set up the last chosen speed The pump can used on a commercial emergency power supply or a commercial UPS which is fitted with a rectifier package 7 3 Meaning of the codes
22. s switched off Once the blockade is reversed you can restart the pump Additionally it will should the situation arise restart itself for up to 5 times If the pump is still blocked after 5 at tempts Error occurs in the display and the pump switches off permanently Only disconnection and reconnection from and to the power supply can restart the pump This as sumes that the cause of the blockage was redeemed 5 7 Turning the head of the RD 3 MiniSpeedy Speedy Freshwater pump with without turnable bypass The head of the RD3 80W pump with bypass can be turned into three directions The bypass is designed to be freely turn able and can be turned in any direction with the pump head The bypass tube can be exchanged Press the socket on the black elbow down a bit and the tube can be pulled out Pince 1956 Kk kkk 6 Operation of the RD3 pumps with controller Important Notice The imprint on the buttons and LEDs may vary troughout the text the functions however remain the same The display is in W the actual measured effective power energy meter consumption ote when you press the but ton the pump in 5 Watt incre ments can be regulated After a loss of the electrical power supply the pump will restart in the last valid setting automatically Pressing the plus key in creases the revolution of the pump Thus the flow rate and the energy consumption in crease Pressing the minus key decr
23. sconnect the plug from the controller pump while the device is in use This can result in serious damages to the electronic com ponents and to dangerous situations due to grounding problems The controller may exclusively be connected and operated on an ELBC protected wiring 30 mA rating and into a grounding receptacle The wiring may not be modified or replaced Electrical installations always have to be compliant and according to national and international directives and requirements Never open the case of the device or of the appending parts if this is not explicitly suggested in the user manual Never apply technical modifications the device Only use original spare parts and accessories Let only authorized customer service facilities conduct reparations Never use the pump with other liquids than water If you have any questions or problems consult an electrician your dealer or the manufacturer Royal Exclusiv Always disconnect the pump from the power supply before working on it Never use the device without water throughput The pump will automatically start when the power connec tion is established unless you press the Stop but ton Then you can only start the pump by pressing the Start button The pump will then automatically ac celerate to the last chosen power setting For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal excl
24. the revolutions per minute Note The pump will start with the display of the type of pump P1 P3 Then the initialization In takes place Afterwards the start message SP and the last selected set wattage will be shown Through the Up and Down we fixed keys performance in 5 Watt increments Pince 1956 Kk kkk Power Consumption Revolution adjustment Brushless Motor Co be 3 1 Quick installation guide Red Dragon 3 Freshwater without speed regulation The model Red Dragon 3 without rev limiter can be op erated submersed and exter nally out of the water Simply plug in the electric socket ready We generally suggest the usage of decouple kits silicone tubes in order to fully take advantage of the warranted low noise level of the Red Dragon 3 pumps 3 2 Quick installation guide RD3 MiniSpeedy BK RD3 MiniSpeedy pump with speed regulation 50 Watt RD3 Mini Speedy skimmer pump 50 Watt RD3 Mini Speedy flow and filter pump 4 Improper usage This manual is indented to inform you correctly und ex haustively i e also over potential risks caused by the pump The user fitter and maintenance technician is re sponsible to check the compliance with the procedures and advises in this manual The RD3 are built with state of the Art technology and to comply with existing safety regulations Nevertheless this device may cause risks for individuals and for property if it is
25. the water level 6 the installati on of a backpressure valve 7 is mandatory In this case the inlet piping of the pump has to be filled with water before the pump is set to operation In such a setup the risk of the pump to run dry is very high when the backpressure valve does not work properly Damages which are caused by the pump running dry are excluded from warranty For usage in polluted water the application of a prefilter is necessary It is recommend to use a quick release or 3 step release so that the pump can be quickly disconnec ted in order to simplify cleaning and maintenance work on the pump The piping has to be installed in a way that possible me chanical tensions which result from varying temperatures do not affect the housing of the pump 5 3 Inlet pipe If no sufficient amount of water reaches the pump because the drag of the inlet pip is to strong the pump will consume a lot of power and the electronics gets very warm in the long run The electronic contains a self protection mecha nism for this case and will lower the power If the pump delivers less and less water after hours or days of operation it is possible that the inlet piping is too large The best thing is to enlarge the diameter of the piping on the inlet side by 1 2 sizes directly in front of the pump in order to maximize the delivery rate and to minimize energy consumption X X Any coupling has to be 100 air proof If a tube is used
26. ulated foreign particles pond usage such as sand or gravel which lead to damages on rotors bearings rotor housing or motor housing that are not covered by warranty 1 2 Our warranty for defects is strictly limited to supplemen tary performance This is upon our choice either removal of defects or replacement delivery free from defects In the Pince 1956 Kk kkk case of challenge impossibility or failure of the supplemen tary performance the customer has the right for impairment or the right to withdraw from the contract Additional expenses which arise because the customer has brought the sales item to another place than his subsidiary The manufacturer explicitly limits the warranty to the pump itself We are not reliable for consequential damages or damages that are caused by a malfunction or failure of the pump such as a loss of animals It is in the responsibility of the customer to provide back up devices for the case of a potential malfunction or failure of the pump 1 3 The customer has to check the goods immediately thoroughly also for product safety Apparent damages have to be reported in written form immediately Hidden damages have to be reported immediately after their dis covery The customer is liable to report transport damages within 24 hours to the carrier and or the delivery service Disregarding the rules for checking and reporting results in a loss of warranty 1 4 Furthermore we are not liable fo
27. upplier vendor or dealer before you start up the pump For more information please visit www royal exclusiv de Simply enter the part number or name into the search box or email info royal exclusiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 1 Defects and claims for compensation disclaimer 1 Defects and claims for compensation 1 1 Barring any further claims we are only liable that the supplied goods are free of defects until the initial transfer of perils Insignificant variations of the contracted appearance and workmanship or marginal limitation of the usability or suitability of the product are unremarkable The warranted condition endurance and usability the prod uct is solely subject to the specification agreed in writing in the product specification and or in this manual Further oral agreements especially from preliminary talks advertis ing and or in related industrial standards will are only valid as integral part of a written contract Only conditions and specifications assured specifically by us are valid We do not accept conditions or specifications made by third par ties Specifically the specification assured in this manual are valid If the customer wants to use the product for other than the intended purpos
28. usiv de All information subject to change We try our best but printing errors reserved Klaus Jansen Richard Byrd Str 7 50829 Cologne Germany Fon 49 0 221 222886 0 Fax 49 0 221 22288622 info royal exclusiv de www royal exclusiv de 4 1 Applications The RD 3 pump is suitable for freshwater brackwater salt water and to pump other non aggressive non explosive liquids that do not contain oil It can haul clean as well as to a certain extent polluted water The pump is not suit able for water with larger particles The pollutants may not exceed 0 8cm in size In general the pump is to be used for applications with clean water Clean water in this case is defined as water not con taining solid particles which could damage the bearings Examples for particles or pollutants not suitable are sand or pyrolosite after a manganese peroxide treatment in a pond Damages caused by such pollutants in the water do not fall under warranty or service The most common use case for the RD 3 pumps are in the context of filtration systems aquariums ponds or swim ming pools and or to supply a beck creek or waterfall The pump is not self supplying and therefore can be used above the water surface and only in combination with a backpressure valve on the inlet pipe In this case the pump has to be filled with water befor it is set into operation Temperature of the liquid 2 to 40 C Environment temperature 0 C to
Download Pdf Manuals
Related Search