LED101 Multi-color LED Lamp
Contents
1. 2 Consol no signal 2 change controller Mido nctarwork 3 The first tube dead change the first tube 4 change the controlling mode I change the tube quantity The frontal tubes 1 The LED tube quantity setting on the console work but the back Setting wrong on the console R check and connect the tubes not work 2 The connecting of signal power line and signal line or change the tube between At the middle not Change the not work others work PCB broad dead work LED tube In one tube there is one Please check the thirteenth place not work or the color PCB LED dead point to get the reference o not equalit how to change LED lamps 1 change the controller 2 amend that place s 1 controller dead interfere 2 the place has strong increace the load of the J RRS a ead power line and socket or Pewer Ane Over 1040 reduce the LED tube quantity increase the XII DMX address setting method for LED controller IL Open the AC power on the controller 2 Press and choose the DMX512 MODE 3 Press SETUP button the screen will shows as DMX addr 4 Press UP and DOWN button to adjust the right address code 5 Press SETUP for confirmation XIII Replace LED lamp 1 Look for the not bright LED lamps For example when the LED tube is white but the color of somewhere is purple it indicates that the green LED is burned 2 Open cover of both sides of LED tube 3 Disassemble the four ca2. Data Value Statement 0 5 BLACK STATIC RED STATIC GREEN STATIC YELLOW 60 65 FAST FLOW1 66 71 FAST FLOW2 R2STE BLACK RUN1 78 83 ROLL CHASE 84 89 ROLL COLOR 90 95 96 101 COLOR 1 4 COLOR1 4 102 107 COLOR1 1 2 108 113 COLOR FLASH 114 119 B amp W FLOW 144 149 R amp G CHASE2 150 155 R amp B CHASE1 156 161 R amp B CHASE2 162 167 R 8 W CHASE1 168 173 R amp W CHASE2 174 179 B amp G CHASE1 1807185 B amp G CHASE2 186191 W amp G CHASE 12197 W 8G CHASE2 198203 RAINBOW CHASE1 204 209 RAINBOW CHASE2 2105215 RAINBOW CHASE3 216 221 RAINBOW CHASE4 222 255 RAINBOW CHASE8 2 Second channel control the speed 4 Fourth channel control the strobe E 6 4 gt ue X Warnning 1 Try the best to avoid the thunder field and high voltage place with strong magnetic field 2 The controller should be install indoor If install in outdoor it should be make the waterproof work 3 The power Line was 15A max If the load is over 15A when connect the LED lamp it should add the additional power socket If the power voltage is 220V the power line can connect 280PCS max If the power voltage is 110V that it is 140PCS max 4 Installation sample picture 220V example MAIN POWER LINE 220V a 200PCS 200PCS 200PCS 5 Installation structure picture TUBE ALUMINUM PANEL 7 XI Problems and Answers 1 Plug no electronic I change socket
3. LED10 1 M ulti color LED Lamp USER MANUAL Please read over this manual before operation the light C Function Introduction 1 System Structure Composed by the multi function controller LED101KT and the LED lamp LED101 1 2 Available using place DISCO hall bar shop CalaOK Stage hall outside building line and etc LED101 1 LED lamp I General Technical Data 1 Size 1000x 50x 75mm 2 Voltage AC86V 240V 60Hz 3 Power Waste P lt 12W 4 Protection grade IP66 5 Withstand Voltage 3750V 6 Life about 50 000 100 000 hours 7 Weight 1 8kg II Main Structure Composed by the high capability R G B three basic colors of LED lamp the hard alnico bracket the switch power and the wire controlling board LED101KT controller I General Technical Data 1 Size 180X 125X 49mm 2 Voltage AC220 240V 50 60Hz 3 Power Waste P 1 5W II General Function 1 With DMX512 input function 2 With 38 kinds of Auto moving mode 3 With 38 kinds of single adjustable moving mode 4 Can one time control 4000PCS max of LED TUBE 5 Auto safe mode data function 6 The initialize data setting mode 7 RGB dimmer by DMX console III Install steps of first time 1 LED tube quantity test Connect to power directly Don t connect with console The LED tube is OK if it will be full white 2 Test the connection between console and all LED tubes Switch on console press MODE button select TEST MODE and press SET UP button the screen will show
4. R amp B CHASE2 28 R amp W CHASE1 R amp W CHASE2 B amp G CHASE1 31 B amp G CHASE2 W amp G CHASE 33 W amp G CHASE2 37 41 42 43 DMX512 MODE 2 To adjust according to the SETUP button Tsfrafion Show Data oa FLASH 0 0 REZ INVERVAL 0 o WEW RUN SPEED 10 0 4 TUBE QTY Over4000 0 NOWE DMX ADDR 65 10 3 UP adding data button Reset the data press the button SETUP to confirm 4 DOWN reducing data button Reset the data press the button SETUP to confirm 5 Set up the DMX address 1 Press MODE key and choose the DMX MODE 2 Press SETUP key to enter 3 And then press UP or DOWN key choosing the Original DMX channel of moving mode The sequence of the four channels is MODE SPEED INTERVAL FLASH or 0 RED GREEN BLUE 4 Press SETUP VII Installation Map Tutel h nl Tube Data cable DMXS12 data cuble_ p 4 512 Controlle VITI DMX512 control mode 1 MODE SPEED INTERVAL FLASH 2 0 RED GREEN BLUE Mode 1 The value of first channel over 0 Mode 2 The value of first channel is Q IX After into the DMX mode will totally receive 4 lines signal to adjust the address by choose UP and DOWN 1 255 initialize the address as 1 1 First channel DMX signal data 0 255 control the 38 kinds of state The following was the data setting and the statement list The DMX value between 0 to 47 are static program do not control be channel 2 3
5. bles of both sides of LED PCB by electric iron Attention Please be care of the function of different color cables BlackGND Red small 12V WhiteA Red big B 4 Take out the LED PCB from the tube 5 Use the static proof electric iron to unsolder the burned LED lamp 6 Install the good LED lamp and solder it with the soldering tin Please pay more attention to the polarity of LED foot The anode has been marked as on PCB The longer fee should be soldered at position 7 Cut away the over long LED foot 8 Reassemble the LED PCB into LED tube Unsteable do not accept control by the controller
6. connection OK if tubes are red All LED tube will be full red if the connection is OK 2 3 LED tube setting Press MODE select ADDRESS MODE and press SETUP button the screen will show Initializing addr Waiting about 2 3 seconds The screen will show OK Address is done once finishing setting 4 Select working mode Press MODE to select working mode Attention Please do as above three steps if you connect LED tubes first time or reconnect them otherwise LED tubes can not work correct IV Structure Map Power A i Supply GND Controller LED control input V Data Signal Line r ao a B Femail Signal Le l A Mail Signal VI Using Illustration COOL MODE SETUP UP DOWN There are four function buttons on the controller MODE SET UP UPand DOWN 1 To adjust according to the MODE button RAINBOW CHASE1 RAINBOW CHASE2 RAINBOW CHASE3 RAINBOW CHASE4 RAINBOW CHASE8 AUTO MODE TEST MODE ADDRESS MODE Factory settings load GRAPH MODE Function BLACKOUT STATIC RED 3 STATIC GREEN STATIC YELLOW STATIC BLUE STATIC PURPLE 7 STATIC CYAN i STATIC WHITE FAST CHANGE SLOW FLOW1 11 FAST FLOW1 12 FAST FLOW2 13 BLACK RUN1 ROLL CHASE ROLL COLOR COLOR 1 4 COLOR1 4 18 COLOR 1 2 COLOR FLASH B amp W FLOW R amp G FLOW 22 G amp B FLOW R amp B FLOW 24 R amp G CHASE1 R amp G CHASE2 26 R amp B CHASE 27
Download Pdf Manuals
Related Search