USER`S MANUAL & SPARE PARTS CATALOGUE
Contents
1. Pag 17 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Kos Ca RAT bet Squeezing pot Take off the spout BC Take off the waste container CSB grasping it from the side Disassembled Orangenius handles Pag 18 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 q 5 ae AAT rangenius o Gina 4 3 Cleaning the squeezing pot KUER H e marine car Take the big cylinder 7 with both hands utilizing the slits B Lift the big cylinder 7 Lift the shock absorber kit 8 grasping it from the upper side C Lift the plastic glide 9 grasping it from the upper part D ATTENTION FOR THE DAILY CLEANING OPERATION IT IS NOT NECESSARY TO REMOVE PLASTIC GLIDE JUST RINSE THE POT WITH THE GLIDE INSTALLED WE DO RECOMMEND THAT THE GLIDE BE REMOVED PERIODICALLY AT LEAST ONCE A WEEK FOR THROUGH CLEANING Rinse from the upper side under tap water Pag 19 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 5 de rangenius v Dini ATTENTION CLEAN ALL THE COMPONENTS REMOVED UNDER TAP WATER SPRAY WITH CETRISAN SOLUTION RINSE AND DRY WITH A TOWEL Rinse the lower part with the glide installed WARNING BEFORE CLEANING THE KNIFE COVER REMOVE THE BLADE FOR SAFETY REASONS Chapter 3 3 Th2. The gear motor is damaged Replace the gear motor The fruit are not juiced and the machine jams The pins projecting out of the small cylinder are jammed or bent Repair or replace the pins The small juicing cylinder is damaged Replace the small cylinder The peels are not unloaded and the machine jams The plastic glide is damaged Replace the plastic glide The cantering pins of the plastic glide are bent Reset the verticality of the centring pins The big cylinder cannot be removed because the orange pusher blocks it The machine has been stopped manually and is out of phase Restart the machine by pressing the start micro switch and wait for the automatic stop The upper cover and or the small cylinder cannot be removed The machine was stopped while squeezing half a fruit Restart the machine in by pressing the start button then wait for the automatic stop These operations must be carried out whit the upper covered properly engaged The machine is noisy The noise repeats at each turn of the cylinder the small cylinder pin bumps against the plastic glide Make sure that the plastic helical guide is correctly mounted and in particular that the helical guide pin is not bent The noise repeats with quick frequency the gear teeth are worn out Or There is too much clearance between the teeth of the two cylinders Replace the gears Adjust the compensation sprin
3. Using the correct Pusher Kit In order to ensure the best performance of the Orangenius please choose the correct pusher kit The size of the oranges you are using dictates the choice of Pusher Kit 2 2 1 Oranges calibre 6 7 diameter 70 80 Orange colour AA WARNING A BEFORE INSTALLING THE SHOVEL KIT PLEASE REMOVE THE KNIFE COVER FROM THE MACHINE Take the orange pusher kit Insert the pusherl kit placing the guides LC on the slides of the shafts Insert the pushers on the hexagonal shafts Pusher kit correctly mounted Pag 9 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 RAT Gift 2 2 2 Oranges calibre 8 9 diameter 60 70 Yellow colour kit Pusher collar VAN ATTENTION VAN BEFORE INSTALLING THE PUSHER KIT PLEASE REMOVE THE KNIFE COVER FROM THE MACHINE Yellow Shovel kit collar Insert the pusher kit placing the guides LC on the slides of the Insert the pushers on the hexagonal shafts shafts Pag 10 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Ve Gs RAT Gift Pusher kit correctly mounted Install the collar for the smaller orange size putting the pins P1 P2 in the slides of the transparent cover S1 S2 as shown in the picture Pag 11 Manual Orangenius Vers 1 0 November 2006
4. Orangenius Manual Ver 1 0 November 2006 Ka ae T rangenius tbat gt To install the collar the closed side has to face the back of the transparent cover Collar If the collar has been positioned correctly a click sound will confirm the correct installation Pag 12 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 af Ca RAT or Gina 2 3 Installation Phase H A ATTENTION A BE CAREFUL REMOVING THE KNIFE PROTECTION OR HANDLING THE KNIFE COVER THE KNIFE IS REALLY SHARP Mounting the transparent cover Place the transparent cover with the 4 pins PCT in the 4 holes of the machine SCM Pag 13 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 VE T Gift gt Place the transparent cover as illustrated in the picture ATTENTION IF THE TRANSPARENT COVER IS NOT CORRECTLY PLACED THE ORANGENIUS DOES NOT START Right position Assembled Orangenius Connect the electronic plug Pag 14 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 RAT Chapter 3 Operative Cycle To turn on the machine proceed as follows Place a container glass bowl etc on the glass tray The Orangenius is now ready Place three oranges in the orange shoot As a guide 3 O
5. of the locking system when the butterfly lever is turned clockwise Pag 29 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 5 de amp rangenius or Gina ATTENTION BE SURE THAT THE BUTTERFLY LEVER IS COMPLEATELY TURNED CLOCKWISE OTHERWISE THE MACHINE WILL NOT START Press the handle of the knife cover and turn the butterfly closing Finally install the transparent cover as showed in chapter 2 Pag 30 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Chapter 6 Maintenance 6 1 Wastage All the wastage produced during the squeezing process is conveyed to the peel container When the peel container is full the machine will stop and an acoustic alarm will start When the alarm sounds for the first time the operator may chose to simply move the container back and forward in order to distribute the peels inside the container evenly and continue to use the Orangentus At the second alarm please unload the container To restart the Orangenius just press the start button ATTENTION The peel container holds only peels and peel oil When unloading the container please check to see if peels have fallen behind the container If so remove them before reinserting the container ATTENTION If the oranges are too small they may jam in the knife area and lift up the transparent cover In th
6. 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 ae rangenius o Dina Knife kit Knife cover kit Insert the knife in the slide of the cover Knife slide pos 4 Insert and screw the knife with the black hand wheel A WARNING A BE CAREFUL TAKING OFF THE KNIFE PROTECTION Pag 27 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Vv Ca RAT wief After the squeezing pot has been installed and the knife has been mounted on the knife cover continue with the following operations Orangenius Check that the butterfly lever is open When the knife cover is installed the two shafts marked A will be inserted into the two holes marked SA and theprimary shaft AM will be inserted into the hole marked SAM As illustrated above Pag 28 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 5 de amp rangenius o Dina To check the right installation of the knife cover the knife cover yellow has to be at the same level of the machine body red Turn the butterfly lever clockwise until a click sound occurs ATTENTION IN CASE THE BUTTERFLY CLOSING CAN NOT BE COMPLETELY TURNED PUSH ON THE COVER HANDLE AND TRY AGAIN The holes SS on either side of the orangenius body are a part of the locking system for the knife cover Please note the two levers S
7. RAT Sri a Da LL S rangenius By Dime USER S MANUAL amp SPARE PARTS CATALOGUE Warning read the manual carefully before attempting to operate the Orangenius juicer VERSION 1 1 NOVEMBER 2006 Manuale Orangenius Vers 1 0 Novembre 2006 Orangenius Manual Ver 1 0 November 2006 wit Orange plett NIUS eg 6 INDEX CHAPTER 1 General Introduction CL Certificate 0fcomphiance uru riore aaa areale PZ 1 2 Preliminary POMark Ss parato RO e Le d e P 2 123 Safety NOMS EE P 2 1 4 Observance and particular warnings iii 1 5 Unpacking procedures assiali AG aa L Packing list siae ri ra EE Aia ii Po CHAPTER 2 Installation 2 1 INSTALLATION Phase I ie P 7 2 2 USING THE RIGHT SHOVEL KIT ORANGE COLOR i P 9 2 3 USING THE RIGHT SHOVEL KIT YELLOW COLOR i P 10 24 INSTALLATION Phase Il canonica P 13 CHAPTER 3 Operative cycle Bul OPERA PIVE d DEE P 15 CHAPTER 4 Disassembling operation and cleaning process 4 1 GLASS TRAY ciano eee laid P 16 GE HALEN P 17 43 SQUEEZING NR RE P 19 CHAPTER 5 Assembly 5 1 ASSEMBLY THE ORANGENIUS A P 21 5 2 INSTALLING THE SQUEEZING POT irienna aine adan AE E SEa E E E E ies Ea EES P 23 5 3 INSTALLING THE KNIFE COVER P 27 CHAPTER 6 Maintanence 6 2 DAYLY OPERATION o Ai P 32 CHAPTER 7 Machine ID 7 2 TECHNICAL SPECIFICATION sneren NENNEN REENEN lai e P 34 7 3 TECHNICAL SERVIC
8. AA into the holes SA A Insert the big cylinder handling it from the upper edge G Please check that the lower cylinder edge is aligned with the squeezing base edge Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 4 Co rangenius bak Insert the plastic glide In the lower part of the glide there are two holes for the centering pins F1 F2 Inside the squeezing pot there are the two centering pins P1 P2 Insert the plastic glide inside the squeezing pot Be sure to insert the glide into BOTH two centering pins F1 with P1 and F2 with P2 Pag 24 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 E o rangenius EM Ip MULO Insert the pin P1 into the hole FI Lower the glide a bit and insert the pin P2 into the hole F2 Push the glide until it reaches the bottom of the squeezing pot Double check that the glide is correctly installed by moving the upper part B back and forward Take the perforated cilinder and insert it on the primary shaft A1 Pag 25 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Ale GE Co Pi AAT rangenius ni Check that the gear of the two cylinders DCP DCG are perfectly aligned Pag 26 Manual Orangenius Vers
9. E CENTRES iisiiiiiiii RE ERE ET SEN EE ences de P 35 CHAPTER 8 Failures Shutdowns Diagnose P 36 CHAPTER 9 Spare Parts Catalogue Bol SEENEN E ee EE P 41 Chapter 1 General Introduction Pag 1 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 1 1 Certificate of compliance The Orangenius has been produced in compliance with international standards and health norms applicable to food machines In particular AAT SPA declares through the Certificate of Compliance included with the machine that the citrus fruit squeezing machine OR M5 PL has been designed and manufactured in accordance with the EEC Directive 89 392 Machine Directive and with the above mentioned norms 1 2 Preliminary remarks e The illustrations and drawings showing the machine are to be considered only as a general reference and are not necessarily precise in every detail e The dimensions and specifications of the machine that are supplied by this manual are not binding and can be changed without any advance notice e The drawings and all other documents supplied as a part of this machine are property of AAT SPA and must not be given to third parties without obtaining written authorisation from AAT SPA e The manual includes the instructions for all the accessories mounted on the base machine e The machine is covered by a warranty as per purchase contract During the warranty period any repair int
10. RANGES 1 CUP OF JUICE 6 ORANGES 2 CUPS OF JUICE 4 we rangenius v dint Activate the main switch on the back of the Orangenius a red led will appear on the switch Press the starting buttons on the side of the Orangenius ATTENTION THE ORANGENIUS WILL CONTINUE TO WORK FOR 20 SECONDS EACH TIME THE BUTTON IS PRESSED FOR A TOTAL OF 6 CICLES 6 ORANGES ATTENTION IF THE TRANSPARENT COVER IS LIFTED WHILE THE MACHINE IS WORKING THE SAFETY SWITCHES WILL STOP THE ORANGENIUS Pag 15 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 lf Ve AAT rangenius tbat Chapter 4 Disassembling operation for cleaning 4 1 Glass Tray Glass tray Rotate the front part of the tray Take off the front part Rear part Front part Take off the grid Pag 16 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 Ca AAT rangenius wr Orkest 4 2 Cleaning operations Lift the transparent cover and follow these instructions Turn counter clockwise the butterfly lever 1 Lift up the knife cover grabbing it from the handle 2 Grasp the pushers 3 from their lower side A and lift them up Remove the small perforated cylinder 4 using the handle 5 Grasp the squeezing pot using both handles 6 Lift up the squeezing pot being careful not to bend the handles
11. achine starts and does not stop although there are no more EE Replace the PCB relay oranges in the orange feeder arm relay are fused The oranges are not cut completely or properly in half The knife is blunt Sharpen or replace the knife The plastic protection has not been removed from the knife Remove the plastic protection The knife is not correctly positioned Check the knife positioning The size of the fruit is not correct Use fruit having the recommended size The machine emits a continual sound and jams during the squeezing phase The waste compartment is full Empty the waste compartment The discharging chute is obstructed Clear the discharging chute The peels photocell is dirty Clean the photocell positioned on the back internal panel of the discharging chute The peels photocell has loosened Adjust the photocell The electronic card is damaged Replace the card The machine does not squeeze all the oranges inserted The idling cycle time is too short Increase the idling cycle time by turning the trimmer found on the PCB relay in a clockwise fashion The electronic card is damaged Replace the card Pag 38 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 AAT Branger ef TT FAILURE REASON SOLUTION The motor runs but all the mechanic parts do not move
12. at case just remove the oranges and continue to work Pag 31 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 6 2 Daily operation To maintain the efficiency of the machine At the end of the day or after 100 juice cups clear the machine by pressing the start button and letting the machine work for a few minutes without oranges then turn off the main switch on the back of the machine and follow the cleaning instructions in Chapter 2 WARNING Please during the cleaning process pay attention to the knife on the cover SHARP BLADE Chapter 7 Machine ID 7 1 Machine Nameplate Pag 32 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 ve Ee AAT In case of any maintenance or overhaul operation not foreseen in this manual or in case of any technical problem our technical service department is readily available for further information or to recommend the necessary intervention While contacting the technical service department please supply the model code and the serial number matricola of the machine on the nameplate attached to the rear of the machine Fig 7 1 PATENT N 5 BREVETTO N ZONA INDUSTRIALE VIA V LANCIA Tel 095 291233 Fax 095 291117 Fig 7 1 7 2 Technical specifications 7 2 1 DIMENSION AND WEIGHT Manual Orangenius Vers 1 0 November _ Dimens
13. e cleaning operation of the squeezing pot the waste container and all the components has to be done daily or after a heavy use The inside of the machine should also be rinsed to clean the spout Pag 20 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 pas Vv EZ AAT e dini Chapter 5 Assembly 5 1 Installing the knife cover Orangenius Insert the waste container d IMPORTANT ALWAYS INSERT THE JUICE SPOUT BEFORE THE SQUEEZING POT Insert the juice spout Insert the squeezing pot grasping both handles When correctly installed the squeezing pot is FULLY inserted inside the machine See illustration above Pag 21 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 5 de e rangenius e dint IMPORTANT AFTER THE INSTALLATION OF THE SQUEEZING POT CHECK THAT THE JUICE SPOUT IS FIXED TO THE MACHINE Check that the juice spout does not detach from the machine Pag 22 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 RAT 5 we H rangenius g t 5 2 Complete the installation of the squeezing pot assembly After inserting the squeezing pot back into the Orangenius Grasp the Shock absorber kit from the upper side When correctly installed the two edges will be in line Insert the shock absorber shafts
14. ervention Something missing here 1 3 Safety norms e THE FOLLOWING NORMS HAS TO BE FOLLOWED FOR YOUR OWN SAFETY Please follow these rules to avoid serious injury e DO NOT USE THE MACHINE WITHOUT READING THIS MANUAL A e Be sure to properly install all of the safety panels BEFORE attempting to use the machine e DO NOT leave any tool or objects inside the machine e Incase of malfunction switch off the machine immediately DO NOT TRY TO REPAIR THE MACHINE WHILE IT IS FUNCTIONING e BEFORE restarting the machine after any maintenance be sure to replace all the safety panels e Remember that your safety and the safety of your colleagues depend on your responsible behaviour e Handle the machine with care follow instructionsand use extra caution if you need to move the machine 1 4 Observance and particular warnings e The personnel working with this machine must know and scrupulously comply with the general safety norms Non compliance with the norms could cause injuries to the personnel and damage to machine parts e The maintenance operations shall be carried out only when the machine is not in use The electrical cord must be disconnected e The user must make sure that all the instructions in this manual are completely followed Pag 2 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 AAT Grong e Any tampering with the safety system is at the user s risk and responsibil
15. gs of the big cylinder by loosening the nut located behind the front panel of the machine Pag 39 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 peas AAT Brongers ef ST FAILURE REASON SOLUTION The fruit is partially juiced low yield The thrust plastic bearing roller of the small cylinder is worn out Replace the thrust bearing roller The clearance between the teeth of the two cylinders is more than 2mm Adjust the compensation springs of the big cylinder by loosening the nut located behind the front panel of the machine The plastic shock absorber are ruined Replace the shock absorber Pag 40 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006
16. ion A Width 260 mm B Height 710 mm C Depth 560 mm Net weight 28 kg Gross weight with box 30 kg 7 2 2 Technical Specifications Electric requirements USA 110 120V 60Hz EC 220 240V 50Hz grounded single phase Motor power 250 W Electromagnetic compatibility in compliance with VDE 0843 IEC801 harness conforming to ENS5011 Orange calibre 9 between 60 and 80 mm Orange feeder arm 6 citrus fruits Peel container capacity N 13 15 oranges Speed 22 oranges per minute 7 2 3 Noise Equivalent level of the weighted acoustic pressure at 1 metre 62 dB Maximum level of the weighted instantaneous acoustic pressure in the work place lower than 120 dB 20uPa 7 2 4 WORK ENVIRONMENTAL LIMITS The environmental limits of the machine are e Temperature from 50 113 F 10 45 C If the temperature is lower than50 F 10 C and near 32 F 0 C when the machine is both installed and dismounted it is important to avoid allowing condensation inside the machine as AAT S P A is not responsible for any possible damages due to this kind of problem Humidity from 20 to 95 7 3 Technical Service Centres In case of any problems requiring our intervention you can contact the following authorised centres during the warranty period at the time of the machine s maintenance and or repair Pag 34 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 AAT SPA Blocc
17. ity e Never disconnect or attempt to bypass the safety protections e AAT s p a is not responsible for any accessories or machinery used in conjunction with Oranfresh Juicing Machines unless AAT s p a supplies such machinery e The careful observance of all instructions is necessary if the machine is to work correctly e In addition when installing the machine please pay particular attention to the general environment in which the machine will be operating e All national laws governing the use of this type of machines must be followed Warning Our company declines all responsibility for damages that arise from not following the instructions mentioned above UNPACKING PROCEDURES Pag 3 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 e Ee RAT n Giani L 3 Lift up the external carton Open the box containing the transparent cover Remove the cover box Remove the transparent cover from the box Pag 4 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 gt Remove the trail Remove the foam box 5 de rangenius Remove the machine keeping the plastic bag wrapped around it IMPORTANT do not grab the machine from the following delicate parts spout 1 handle 2 shovel 3 butterfly handle 4 Pag 5 Manual Orangenius Vers 1 0 November 2006 O
18. o Palma I Z I 95030 CATANIA Tel 0039 095 291233 Fax 0039 095 291117 E mail info oranfresh com www oranfresh com Branches ROME Via Sannicandro di Bari n 8 10 00193 ROMA Tel 0039 06 22446984 Fax 0039 06 22446988 E mail inforoma oranfresh com MILAN Via Moncenisio n 79 20089 ROZZANO MI Tel 0039 02 57510449 Fax 0039 02 57510457 E mail infomilano oranfresh com CHAPTER 8 Pag 35 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 pes AAT Brongers ef TT FAILURES SHUTDOWNS DIAGNOSIS ATTENTION Only qualified personnel shall carry out the following operations FAILURE REASON SOLUTION The machine does not Start First make sure that the machine is connected to an outlet supplying the appropriate voltage and preferably a dedicated line the top lid of the machine is closed and the main switch on the rear panel is on The machine is not connected with the outlet Connect the machine to an outlet The plug has not been inserted correctly Connect the plug correctly avoid adapters and multiple jacks The main switch has not been enabled Enable the main switch positioned on the rear panel of the machine The upper cover of the machine is open The upper transparent cover of the machine is open The line fuse is burnt out Replace the fuse with one of the same value The motor p
19. rangenius Manual Ver 1 0 November 2006 de amp rangenius o Dina PACKING LIST TRASPARENT COVER KIT MAIN BODY KNIFE GLASS TRAY KIT YELLOW SHOVELS KIT FOR ORANGE SIZE 60 70mm YELLOW SHOVELS KIT FOR ORANGE SIZE 70 85mm e SANITIZER CETRISAN e CLEANING CLOTH e CLEANING SET FOR PERFORATED CYLINDER e PLASTIC GLIDE e FUSES Pag 6 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 is Ca RAT or infek Chapter 2 Installation 2 1 Installation PHASE I Assemble the Glass tray kit and place it on a secure horizontal surface Place the Orangenius on the Glass tray as follow 1 the foot P that can be used to assemple the machine has to be placed on top of the part PA of the ray 2 the side of the tray has to be aligned with the lower sides of the machine HOW TO INSTALL THE KNIFE Glass tray correctly installed Knife cover Insert the knife in the slide of the cover Pag 7 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 5 de amp rangenius o infek Knife slide pos 4 Insert and screw the knife with the black hand wheel Knife correctly installed Pag 8 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 pa E i AAT rangenius wr Gift 2 2
20. rotection fuse is burnt out Replace the fuse with one of the same value The fastening butterfly lever in the knife cover is not in the ON position The motor protection fuse behind the RagcAfne is burnt out Turn clockwise the fastening lever in the knife cover in the ON position Replace the fuse with one of the same value Manual Orangenius Vers 1 Pfyevember 2006 Qrangenius Ma he line fuse placed belfin pier the fuse ith one the Brongers sb ST The machine is jammed Clean the internal parts of the machine and make sure that there are no fruits or peels inside the squeezing zone The machine starts and does not stan althoncah The micro switch positioned on the gear motor is damaged Replace the micro switch If these checks done so far do not yield positive results please call the technical service The machine starts and does not stop although there are no more oranges in the conveyor The micro switch positioned on the gear motor is damaged Replace the micro switch The electronic card is not working Replace the electronic card If these checks done so far do not yield positive results please call the technical service Pag 37 Manual Orangenius Vers 1 0 November 2006 Orangenius Manual Ver 1 0 November 2006 pes AAT Brongers refe TT FAILURE REASON SOLUTION The m
Download Pdf Manuals
Related Search