Manual for HC174D
Contents
1. 4 Image Setting Phase Adjustment Main Menu Oo zo roo esf caer Serine H 80 0KHz V 75 0Hz 1280x1024 Color Setting Es soe a Color Setting 5500 6500 9300 amp EXE B 4 User s Manual OSD Description Clock adjustment Select the Clock Adjustment option to reduce the vertical flicker of characters on the screen Enter the option and adjust the level Phase adjustment Select the Phase Adjustment option to reduce the horizontal flicker of characters on the screen Enter the option and adjust the level How to adjust color Select the Color Setting option on the Main Menu and then enter the option Move the cursor to one of the preset options and select it User defined option Move the cursor to the User option and select it 1 To adjust the red enter the R option and adjust the level 2 To adjust the green enter the G option and adjust the level 3 To adjust the blue enter the B option and adjust the level User s Manual OSD Diagram Main Menu ot 7199 00 esf H 80 0KHz V 75 0Hz 1280x1024 OSD Setting OSD H Position OSD Setting OSD V Position OSD Time out OSD Transparency 0 lt 1 lt 2 lt 3 lt 4 lt 5 lt 6 OSD Description How to set the OSD Select OSD Setting on the Main Menu and then enter the option OSD horizontal adjustmen2. INSTALLATION p wa Align the monitor with the opening in the base Note that the longer section of the base points forward onap the monitor into its base A clear click sound will affirm that the base is connected correctly Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully engaged in the base REMOVAL 1 2 3 Flip over the monitor so that it us upside down Press the 2 clips that hold the monitor in place Gently press and hold the 2 clips while pulling the base from the monitor unit they are unattached POWER POWER SOURCE Make sure that the power cord 1s the correct type required in your area This LCD monitor has an Internal universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment 15 required Connect the AC power cord one end to your LCD monitor s AC input socket the other end to wall outlet 10 11 User s Manual User s Manual CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure below 1 Connect one end of the 15 pin D Sub cable to the back of the monitor and connect the other end to the computer s D Sub port 2 Connect one end of the 24 pin DVI cable Dual input mode optional to the back of the monitor and connect the other end to the computer s DVI port 3 Connect the audio cable between the m
3. be connected Connect the Signal cable from the monitor to the VGA card Press the power button to turn on the monitor position The power indicator will light up Figure 4 External Control Button EXTERNAL CONTROLS Menu Enter Power Button Power Indicator Volume lt 6 Auto Adjustment User s Manual FRONT PANEL CONTROL e Power Button Press this button to switch ON OFF of monitor s power e Power Indicator Green Power On mode Orange Off mode e MENU ENTER 1 Active OSD menu or function adjust confirm or 2 Exit OSD menu when in volume OSD status e Volume lt gt 1 Activates the volume control when the OSD is OFF 2 Navigate through adjustment icons when OSD is ON or adjust a function when function is activated e Auto Adjust button When OSD menu is in off status press this button to activate the Auto Adjustment function The Auto Adjustment function is used to optimized the H Position V Position Clock and Focus NOTES e Do not install the monitor in a location near heat sources such as radiators or air dusts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock e Save the original shipping box and packing materials as they will come in handy if you ever have to ship your monitor e For maximum protection repackage your monitor as it was originally packed at the factory To keep the monitor looking new period
4. feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse 20 User s Manual TECHNICAL SUPPORT FAQ amp A FOR GENERAL DEFECTIVE PROBLEM amp QUESTION POSSIBLE SOLUTION nokon Check if the Power Switch is in the ON position Power Cord should be connected Check if the PC system is Plug amp Play compatible No Plug amp Play Check if the Video Card is Plug amp Play compatible Check if the D 15 plug pin of Video Cable is bent Picture is fuzzy Adjust the Contrast and Brightness Controls Picture bounces or a wave pattern is present in the picture Move electrical devices that may cause electrical interference Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitor s video cable is properly connected to the computer Inspect monitor s video cable and make sure none of the pins
5. or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Unplug the unit during a lightening storm or when it will not be used for long period of time This will protect the monitor from damage due to power surges Do not overload power strips and extension cords Overloading can result in fire or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor Do not attempt to service the monitor by yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 5A The wall socket shall be installed near the equipment and shall be easily accessible User s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem Due to the nature of the fluorescent light the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappe
6. 15 17 19 inch TFT LCD Monitor USER S MANUAL User s Manual Before operating the monitor please read this manual thoroughly This manual should be retained for future reference FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The device complies with Parts 15 of the FCC Rule Operation is subject to the following two conditions 1 this device may not cause harmful interfer
7. T SUPPORT Your computer has been set to unsuitable display mode set the computer to display mode given in the following table FACTORY PRESET TIMING TABLE VIDEO MODE RESOLUTION HORIZONTAL VERTICAL APPLICABLE FREQUENCY kHz FREQUENCY Hz MODEL 640 x 480 31 469 59 94 15 17 19 15 AT IA9 640 x 480 15 17 19 187 177 19 1577177719 800 600 1517 19 187 177 19 187 177 19 1024 768 15 17 19 187 177 19 17719 1280 1024 1 77 19 157 177 19 157 177 19 720 400 1547 19 1577177719 187 177 19 VESA 1152 x 870 67 500 75 00 1 77 19 22 User s Manual CONNECTOR PIN ASSIGNMENT 15 Pin Color Display Signal Cable PINNO DESCRIPTION PINNO DESCRIPTION gt 5V 2 Gen 10 Ground _ Bue __4__ Ground 12 DC Serial Data 776 RGmmd V amp m 8 BGround J 24 Pin Color Display Signal Cable Dual Input Mode DESCRIPTION PINNO DESCRIPTION 6 DDCCok 18 TMDSDataO0s 7 DDCDaa 1 19 TMDSDetaO 5Shield 8 AnalogVericalsyno 20 TMDSData 9 1 2 TMDSData5t 11 TMDSDetai 3Shield 25 TMDSClock 12 TMDSDeata3 24 TMDSClck 23
8. aphics VGA mode Select the VGA Mode option to set the monitor for VGA display Enter the option and select 720 400 or 640x400 User s Manual OSD Diagram OSD Description Recall the factory settings Select the Factory Preset option to change between the monitor s default settings and the current settings Enter the option and select On or Off Other Setting On Off Input Setting Select the Input Setting option to change Sjoe i between the analog D Sub or Digital DVI source Enter the option and select Analog or Digital Main Menu Analog Digital H 80 0KHz V 75 0Hz 1280x1024 PLUG AND PLAY Plug amp Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The DDC2B is a bidirectional data channel based on the I C protocol The host can request EDID information over the DDC2B channel THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green monitor standards as set by the Video Electronics Standards Association VESA and or the United States Environmental Protection Agency EPA and The Swedish Confederation Employees NUTEK This
9. approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only PRECAUTIONS Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance Use only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator
10. are bent Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key The power LED is ON orange but there s no video or no picture Missing one of the primary ee LUE colors RED GREEN or Inspect the monitor s video cable and make sure that BLUE none of the pins are bent Screen image is not centered Adjust pixel frequency CLOCK and FOCUS or press or sized properly hot key AUTO Picture has color defects Adjust RGB color or select color temperature white does not look white Horizontal or vertical Use win 95 98 shut down mode Adjust CLOCK and disturbances on the screen FOCUS or perform hot key AUTO CLOCK pixel frequency controls the number of pixels scanned by one horizontal sweep If the frequency is not correct the screen shows vertical stripes and the picture has not correct width FOCUS adjusts the phase of the pixel clock signal With a wrong phase adjustment the picture has horizontal disturbances in light picture For FOCUS and CLOCK adjustment use dot pattern or win 95 98 shut down mode pattern 21 User s Manual ERROR MESSAGE amp POSSIBLE SOLUTION CABLE NOT CONNECTED 1 Check that the signal cable is properly connected If the connector is loose tighten the connector s screws 2 Check the signal cable s connection pins for damage INPUT NO
11. ars You may find slightly uneven brightness on the screen depending on the desktop pattern you use The LCD screen has effective pixels of 99 99 or more It may include blemishes of 0 01 or less such as a missing pixel or a pixel lit all of the time Due to the nature of the LCD screen an afterimage of the previous screen may remain after switching the image when the same image is displayed for hours In this case the screen is recovered slowly by changing the image or turning off the Power Switch for hours When the screen becomes black or flashing or cannot illuminate any more contact your dealer or service center to replace parts Don t repair the screen by yourself User s Manual BEFORE YOU OPERATE THE MONITOR FEATURES e 15 17 or 19 TFT Color LCD Monitor Crisp Clear Display for Windows Recommended Resolutions 1024 X 768 60Hz for 15 monitor 1280 X 1024 60Hz for 17 amp 19 monitors e EPA ENERGY STAR e Ergonomic Design Space Saving Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items LCD Monitor Reference only the real feature is depended on selected model Cables and User manual DVI Cable dual input mode optional User s manual Warranty card 9 User s Manual INSTALLATION INSTRUCTIONS Install 15 17 19 Remove 17 15 19 Figure 1 Installing and Removing the Base
12. at plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays TCO 99 requires that batteries the colour generating layers of display screens and the electrical or electronics components shall not contain any cadmium Mercury Mercury is sometimes found in batteries relays and switches TCO 99 requires that batteries shall not contain any mercury It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit There is however one exception Mercury is for the time being permitted in the back light system of flat panel monitors as there today is no commercially available alternative TCO aims on removing this exception when a mercury free alternative is available Lead Lead can be found in picture tubes display screens solders and capacitors TCO 99 permits the use of lead due to the lack of commercially available alternatives but in future requirements TCO Development aims at restricting the use of lead Bio accumulative is defined as substances which accumulate in living organisms Lead Cadmium and Mercury are heavy metals which are bio accumulative The d
13. ence and 2 this device must accept any interference received including interference that may cause undesired operations CANADA This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulation This device complies with requirement of EMC directive 89 336 EEC with regard to Electromagnetic Compatibility and 73 23 EEC and 93 68 EEC with regard to Low Voltage directive Socket outlet shall be installed near the equipment and shall be easily accessible User s Manual TCO 99 FOR OPTIONAL MODEL Congratulations You have just purchased a TCO 99 approved and labelled product Your choice has provided you with a product developed for professional use Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products Why do we have environmentally labelled computers In many countries environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment With the growing manufacture and usage of electronic equipment throughout the world there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal By proper selection of these materials and substances the impact on the environment can be minimized There are also other characteristics of a comput
14. er such as energy consumption levels that are important from the viewpoints of both the work internal and natural external environments Electronic equipment in offices is often left running continuously resulting in unnecessary consumption of large amounts of energy and additional power generation From the standpoint of carbon dioxide emissions alone it is vital to save energy What does labelling involve The product meets the requirements for the TCO 99 scheme which provides for international and environmental labelling of personal computers and or displays The labelling scheme was developed as a joint effort by the TCO The Swedish Confederation of Professional Employees Svenska Naturskyddsforeningen The Swedish Society for Nature Conservation and Statens Energimyndighet The Swedish National Energy Administration Approval requirements cover a wide range of issues ecology ergonomics emission of electrical and magnetical fields energy consumption and electrical safety Ecological criteria impose restrictions on the presence and use of heavy metals brominated and chlorinated flame retardants and other substances The product must be prepared for recycling and the manufacturing site s shall be certified according to 15014001 or EMAS registered Energy requirements include a demand that the system unit and or display after a certain period of inactivity shall reduce its power consumption to a lower level in one or more sta
15. ges The length of time to reactivate the system unit shall be reasonable for the user Labelled products must meet strict environmental demands for example in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics User s Manual Below you will find a brief summary of the ecological requirements met by this product The complete ecological criteria document can be found at TCO Developments website http www tcodevelopment com or may be ordered from TCO Development SE 114 94 STOCKHOLM Sweden Fax 46 8 782 92 07 E mail development tco se Information regarding TCO 99 approved and labelled products may also be obtained at http www tcodevelopment com Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates cables and housings Their purpose is to prevent or at least to delay the spread of fire Up to 30 by weight of the plastic in a computer casing can consist of flame retardant substances Many flame retardants contain bromine or chlorine and these flame retardants are chemically related to PCBs polychlorinated biphenyls Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects including reproductive damage in fish eating birds and mammals due to the bio accumulative processes when not disposed of in accordance with strict standards for disposal TCO 99 requires th
16. ically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it User s Manual HOW TO ADJUST A SETTING OSD Diagram Main Menu 52 0 5 9 T HH NU 4444 H 80 0KHz V 75 0Hz 1280x1024 DIDI H 80 0KHz V 75 0Hz 1280x1024 Main Menu E 0 zx 99 09 xf 9 nage semna H 80 0KHz V 75 0Hz 1280x1024 Image Setting SOMSA Esser HH E E Image Setting OSD Description Brightness adjustment Select the Brightness option on the Main Menu Enter the option and adjust the level Contrast adjustment Select the Contrast option on the Main Menu Enter the option and adjust the level How to adjust screen position and quality Select Image Setting on the Main Menu and then enter the option Horizontal position adjustment Select the H position option to shift the screen image to the left or right Enter the option and adjust the level Vertical position adjustment Select the V position option to shift the screen image up or down Enter the option and adjust the level OSD Diagram Image Setting e Terre Gack Aajesinent
17. isplay unit is an electric device which may contain hazardous materials components and that is needs to be taken care of at end of life according to following information procedure http www hellmann pm de User s Manual TABLE OF CONTENTS SAFETY NOTICE mendis edi 7 PRECAUTIONS eerte tnter 7 SPECIAL NOTES ON LCD MONITORS cetera 8 BEFORE YOU OPERATE THE MONITOR eee 9 FEATURES cope chu DM MI MIELE UE 9 CHECKING THE CONTENTS OF THE 9 INSTALLATION INSTRUCTIONS eerte 10 POWER PME EE 10 CONTROLS AND CONNECTORS teet tnnt 12 ADJUSTING THE VIEWING ANGLE cette 13 OPERATING INSTRUCTIONS cernerent nt 14 GENERAL INSTRUCTIONS centre 14 FRONT PANEL CONTROL 4000004 15 HOW ADJUST A 4 0400 16 PLUG AND PLAY 20 TECHNICAL SUPPORT FAQ cernentes 21 Q amp A FOR GENERAL DEFECTIVE eet 21 ERROR MESSAGE amp POSSIBLE 22 CONNECTOR PIN ASSIGNMENT reete 23 User s Manual SAFETY NOTICE The changes or modifications not expressly
18. onitor s audio input and the PC s audio output green port 4 Plug the AC power cord one end to LCD monitor s AC input socket the other end to Wall outlet 9 Turn on your monitor and computer 000000000 24 400 9 00000000 Figure 2 Connecting Cables VGA Input DVI Input optional Audio Input Power AC Input User s Manual ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor then adjust the monitor s angle to your own preference e Hold the stand so you do not topple the monitor when you change the monitor s angle e You are able to adjust the monitor s angle from 0 to 14 O Figure 3 monitor s angle NOTES Do not touch the LCD screen when you change the angle It may cause damage or break the LCD screen Be careful not to place fingers or hands near the hinges when tilting the monitor otherwise pinching can result User s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off The other control buttons are located at front panel of the monitor See Figure 4 By changing these settings the picture can be adjusted to your personal preferences The power cord should
19. t Select the OSD H Position option to adjust the horizontal position of the OSD Enter the option and adjust the level OSD vertical position adjustment Select the OSD V Position option to adjust the vertical position of the OSD Enter the option and adjust the level OSD timer setting Select the OSD Time out option to set the OSD time out from 10 to 120 seconds Enter the option and adjust the level OSD Transparency setting Select the OSD Transparency option to adjust the transparency of the OSD Enter the option and adjust the level OSD Diagram OSD Setting OSD Color 12 34 5 6 OSD Setting English BAHN Deutsch Frangais Espa ol Italiano Portugu s Nederlands Other Setting Other Setting Bos Wade Text Graphic Other Setting c es es VER ose 720X400 640X400 User s Manual OSD Description OSD color setting Select the OSD Color setting option to adjust the color of the OSD Enter the option and adjust the level Language Select the Language option to change the language of the OSD Enter the option and select a language Reference only the OSD Language is depended on selected model Volume adjustment Select the Volume option to change the volume level Enter the option and adjust the level DOS mode Select the DOS Mode option to set the monitor for DOS display Enter the option and select Text or Gr
Download Pdf Manuals
Related Search