SWING GATE OPENER SW43O SERIES
Contents
1. opens 2 If the gate hits something Actuators reverse for 3 seconds warning light blinks until next command received When closing the gates 1 Warning light will blink for 3 seconds then Actuator 2 closes 4 seconds later the Actuator 1 closes 2 If the gate hits something Actuators reverse for 3 seconds warning light blinks until next command received Sa Lamp control on and off by remote control Simply switch on and off the lamp by the key which had proceeded the RF lamp learning Remark The gate operation works properly only after sucessful Opening Closing Learning Copyright SW 430 Version 1 0 Page 5 6 Photocell Optional 1 During Opening When the loop of photocells has been intercepted system will A ignore if the Actuator 2 has been activated OR B halt if the Actuator 2 hasn t been activated yet 2 During Closing When the loop of photocells has been intercepted system will stop closing the gates and then open both gates simultaneously until the set position Auto close 30 seconds or 60 seconds later only when this function is enabled depends on your setting of key 1 of dip switch warning light will blink for 3 seconds then Actuator 2 closes 4 seconds later Actuator 1 closes When the process finished warning light will be switched off Manual gates control on the PCB 1 The operation is the same as remote one key press will open the gate next press to stop next to close2. 90 Operating Time around 15 Sec Open Range 120 Max Duty Cycle 20 Operation Temperature 20 65 C Overload Protection Yes _ Backup Recharging Battery Foundation a Yes Not Including Battery 12V 7AH Auto Gate Close Adjustable timer off 30 60sec _ Extension Terminal Warning Light Photocell Back up Battery RF Carriage 315 MHz 433 92 MHz Approx 30 50 Meters Control Range Copyright sw 430 Version 1 0 Page 8
3. USER S MANUAL SWING GATE OPENER SW430 SERIES 3 00m max 3 00m max 200kg max 200kg max Important Safety Advice 1 Knowledge of the relevant electro technical regulations is required 2 Training in use and maintenance of safety equipments is necessary 3 Professional assistance is required when some mechanism adjustment is needed 4 Always lay mains and control cables separately 5 Test every equipment before initial operation 6 Make familiar with the use of the system before initial operation Content of the Kit x2 Actuator Gd N x2 x2 Control Box Remote Control Warning Light Key to manually unlock lock the actuator SS x4 Fixing bracket for pillar Fixing bracket for gate Fixing part for pillar Wiring Diagram Warning Light Control Box Actuator Min 15cm 4 DA Photocell F J Photocell Important Safety Advice 1 Knowledge of the relevant electro technical regulations is required 2 Training in use and maintenance of safety equipments is necessary 3 Professional assistance is required when some mechanism adjustment is needed 4 Always lay mains and control cables separately 5 Test every equipment before initial operation 6 Make familiar with the use of the system before initial operation Content of the Kit E x2 Actuator nas a x2 wy x1 S iea Control Box Remote Control Warning L
4. ction press Auto button on the PCB for 3 seconds while the PCB is on After release the Auto button it will enter the opening closing learning mode as below 1 The system will close the gates first lease remove any obstacle could possibly block the gate Auto efore the actuators start the warning light will blink for 3 seconds hen Actuator 2 will close first and then Actuator close 1 second later fter 3 seconds Actuator 1 will open the gate 1 fully aiting for 3 seconds Actuator 2 will open the other gate 2 fully fter 3 seconds Actuator 2 will close fuly first waiting for 3 conds Actuator 1 will close fully ystem repeats the actions of point 2 and 3 one more time er 3 seconds system checks operation of Actuator 1 and Actuator 2 together er learning process succeeded the system is ready for use the system blinks after this learning mode which means learning in vain lease make sure that there s no obstacle on the way then try again to trigger the learning mode 1 sLAgyu o a o DOLE s5 v NOTE The Opening Closing Learning couldn t be done successfully due to the over weight of the gates Theni the Current Limit needs to be adjusted Please refer to P7 of this manual If any assistance is needed please contact the technicians of our agent Copyright sw 430 Version 1 0 Page 4 5 Remote Learning activation of remote control for gate and lamp operation To activat
5. e the remote control service please proceed the following steps A RF gate learning for Open Close the Gates 1 Press RF key on the PCB for over 2 seconds while the PCB is on 2 You ll see the LED light on learning mode entered please press any key on the remote control LED will now blink for 3 times learning succeeded or light off after 10 seconds without blinking learning failed please try again the whole process 3 Please repeat the step 1 and 2 to activate another remote control otherwise the unlearnt remote control won t be recognized by the system B RF lamp learning for Turning On Off the Garden Lamp Proceed with RF lamp key on the PCB and another key on the remote control as step 1 3 above Note Up to 8 different RF remote control keys can be learnt for each function by this system gates amp Garden Lamp Remote Control Choose two of the four keys to proceed RF learning The rest of the keys are available for other purposes such as Garage Door Opener The remote control has 4 keys on it and choose two of them to proceed RF learning for one key gate control and lamp control separately Operation open close and stop by remote control The remote operation is very simple one key press will open the gate next press to stop next to close the gate next to stop and so on When opening the gates 1 Warning light will blink for 3 seconds then Actuator 1 opens 4 seconds later the Actuator 2
6. ff Os 2 0AN 31Ang maa Maximum Current Limit means also the worst sensibility could shorten the life of motor please try lower current limit first Second Highest Current Limit Minimum Current Limit When user switches several switches on for safety reason system will choose the lowest switch 4instead of switch 6 or 8 current limit setting automatically Copyright Sw430 Version 1 0 i Page 7 Optional Accessories 1 Set of Photocell Operation of Photocell Select a proper installation site where the sender and receiver can be along the same line and at the same height Connect to the opener s PCB as wiring diagram above Power on the system try and see if it works properly by interruptting the IR between the sender and receiver for times The relay in the receiver should respond accordingly while LED switches ON and OFF With photocell well installed while it s triggered during opening the gates the gates will ignore the interruption and open While it s triggered during closing the gates the gates will reverse for 3 seconds and stop and warming light will keep blinking untill next command sent Specifications Model SW430 Power Supply 230V AC 21096 50Hz 110V AC 60Hz available Power for Motor 12VDC Maximum Gate Weight 200KGS 440Lbs x 2 Max Maximum Gate Width 3 0M 3 0M 20Feet Stroke Length 350mm 15in Drive ACME
7. ight Key to manually unlock lock the actuator x4 Fixing bracket for pillar Fixing bracket for gate Fixing part for pillar Wiring Diagram O a ra Actuator Garden Warming Light wa Control Box ERA ctuator Min 15cm ff j AN Photocell f J Photocell Instruction of Installation 1 Assemble the metal fixing brackers for the gate pollars And then fix the bracket to the pillar IMPORTANT If the hinge of your gate is more than 210mm from the edge of the pillar it is necessary to adapt the pillar to ensures the hinge is less than 210mm from the edge of the pillar INCORRECT CORRECT ps Po 7 PLAN VIEW 2 Fix the actuator to the fixing bracket 3 Unlock the actuator and adjust the stem of the actuator Normally the factory preset is already 10mm from the end of the stroke if it is difficult to move the stem by hand drive it electrically to avoid damage to the gate or kit OPEN Copyright SW430 Version 1 0 Page 1 2 4 Fix the metal bracket on the gate and check that the actuator does not touch the pillar If this is the case it will be necessary to make a notch in the corner of the pillar 5 Test the opening of the gate manually It must move freely by itself If not you must insert the stem of the actuator in another of the fixing bracket If n
8. o problem lock the actuator 6 The position of the stop ends depends on the distance E of the gate hinge from the edge of the pillar The table below gives the position of the stop end according to E E angle E lt 12mm 120 42mm lt E lt 67mm 110 67mm lt E lt 123mm 100 123mm lt E lt 210mm 90 The system is ready to program and operate Copyright SW430 Version 1 0 Page 2 Connection Diagram 3 Thermal Fuse to transformer Crs U 230 VAC in Backup battery 230V AC 230 VAC out for Garden Lamp a 3 S 12 VDC input from main PCB To transformer 12V AC ip Switches Color indication for motor wire Black wire for Red wire for 12V DC Antenna Actuator1 Warning Light To external Garden Lamp switch For external LED displa Garden Lamp Manual Button Open close Manual Button 12V DC output to small PCB PHOTOCELL SENDER PHOTOCELL RECEIVER Bana TG Copyright SW 430 Version 1 0 Page 3 Transformer AC Wiring Inside of the control box the wiring should be like the photo on the left u AQEZ OV G Opening Closing Learning Please proceed this function before using this product otherwise the system will drive the gates improperly E g The gate can t close completely or can t open to the intended degree with some stroke length left unused To activate this fun
9. the gate next to stop and so on 2 Optional handset or external wall button is available Connected to O C amp GND terminals Manual lamp on Simply switch on and off the lamp by the Manual lamp on key Clear RF memory Press Clear key on the PCB for over 2 seconds while the PCB is on You ll see the LED blinking for 2 5 seconds then the RF memory has been cleared Reset Press Clear key on the PCB and input AC power keep pressing Clear key for over 2 seconds You ll see the LED blink for 2 seconds and light on for 3 seconds then light off Once the mentioned actions have been carried out all RF data will be cleared Quick release Use the Key to unlock the actuator to move the gates manually Clutch adjustment The SW430 series feature a clutch mechanism inside the actuator as an additional protection Any adjustment for the clutch requires professional assistance Copyright SW 430 Version 1 0 rf Page 6 Settings of Dip Switches The default setting of dip switches OBBBUEEE aula 5 Function ON OFF Auto Close Yes No AN Auto Close Timer 60 Sec 30 Sec KA Gate Type Heavy Gate Light Gate KE Current Limit selected unselected NOTE The current limit setting could be needed to adjustment according the weight of the gates during Opening Closing Learning Approx current limit values for different dip switch setting switch 4 switch 5 switch 6 All o
Download Pdf Manuals
Related Search