TT 2000 Pipeline & Cable Locator User Manual
Contents
1. model is the top receivers in the target pipelines will be the largest peak response Airframe associate transmitters receivers will face made at the walk along the curve around adjust sensitivity to the scale readings remain within When peak response local stop moving back and forth on both sides of the pipelines receiver to identify peak response Then receiver local moves in the direction of maximum pause Raising receiver lightly back and forth movement of the peak to determine the precise location of pipelines position in the target for the markings The precision and the ability to avoid disturbing of peak value method is much higher than the valley value method it must be used in all kinds of works The response when receiver is right over the objective pipelines is zero valley value EN m zero response poe O AT mull The valley value method is quick but the precision is bad it mainly uses to track the pipelines and check the correctness of peak value method orientation Tune the receiver to the peak value response to speed up tracking the pipelines you can hold the receiver at any trend because the valley value response doesn t rest on the orientation of the pipelines When you walk along the pipeline you may move the receiver left and right and observe the valley value response right over and two sides of the pipeline When you use valley value response mode and as the receiver is in a right angle with the cable2. and press to retune to the working mode If there is a strong radiate field maybe there s a radio station nearby the measure method at this time is make the antenna s underside 5 centimeters higher than the ground and reduce 5 centimeters from the result that is just the pipeline depth 9 1 9 LCD LCD shows output signal mode and all kinds of functions 5 1 10 Keyboard Control the keyboard to choose operating mode and kinds of functions 5 1 11 Cell sources Unscrew the fastening screws of the top of the cell top to open the cell storehouse there are 1 cell box contains 10 cells when it is short of electricity please recharge it or to change all the cells 5 1 12 Accessories Charger take along bag earthing line user manual Inductive clamp and headphone 5 1 13 Receiver Inner are the receiver antennas choose the peak value mode the machine surface is in a right angle with the ground the antenna will give peak value response Choose valley value response whatever the orientation of the machine surface it can give valley value response to the objective pipelines 5 2 TT2000 Pipeline amp Cable Locator Transmitter s Synopsis Panel interface TT2000 Pipeline amp Cable Locator The transmitter adopts high capability MPU to control easy and convenient to operate with English menu It has the function of memorizing the output signal intensity in Inject mode you can do real time measure to check the outpu
3. batteries and the receiver uses 10 1 2V Ni NH cell 1 5 AH Ni Nh chargeable cell or 10 No 2 alkalescency batteries You cannot charge over 8 hours 1 4 Services Company to be equipped with the service center in SHANGHAI it can provide prompt and high quality service for the customer When the instrument cannot work normally make sure it is the problem of instrument itself first then please promptly contact with the service center and provides the instrument model the serial number as well as the detailed accurate breakdown description The engineer in the service center can provide some instructions and analyze the preliminary reason for the customer If the question still could not be solved please deliver the instrument to the service center to do repair 2 1 Main functions 1 Detect the underground cable and pipeline route 2 Measure the underground cable and pipeline depth 3 Determine the underground cable and pipeline insulation degree 4 Determine the route and depth of the cable and pipeline without touching the transmission signal 2 2 Main characteristics A Use the newest integrated circuit and signal processing technology to achieve outstanding test performance B The survey signal transmission includes 1 Direct Inject method In has Injected the spot on the pipeline to survey the route and the burying depth this method measuring accuracy is high ant jamming ability 2 Induction coupling method In the railroad
4. be careful all the time and don t forget Safety Comes First Attention The transmitter has high output pressure may reach 500V do not touch the wire which was stimulated 1 3 Attentions 1 3 1 Depth survey When active signal is existed on the simple pipeline only then Pinpoint has the significance in the depth survey requests not to be able to have the obvious signal on the neighbor pipelines the goal pipeline must be straight moreover in 10 meters does not have the T shape branch Three Contacts In addition if the transmitter uses the Induction mode then when leaves the transmitter in the 20 meters to use the depth survey it is unable to obtain the exact result 1 3 2 Cleanness maintenance If needs to remove the silt or dirt on the pipeline amp cable locator please use the sponge and tepid water also may use the weak basicity soap to remove the stubborn dirt Don t use any solvent to clean The TT2000 Pipeline amp Cable Locator has certain rainproof function but strictly prohibits immerging it in the water does not guarantee the waterproof and leak proof quality Do not deposit the instrument in the moist place especially the place with caustic gas 1 3 3 Cell When the power source is insufficient charge cells or corresponding dry battery in time to guarantee the enough electric power Do pay attention to the polarity of the cell The transmitter uses 10 1 2V 4 5AH Ni Nh chargeable cell or 10 No 2 alkalescency
5. is viable for the cables which are not convenient or difficult to inflict signals to locate As for the cables taking part from the wooden telegraph pole cement telegraph pole or the lighting pillar you can operate the transmitter at the Induct mode and put it alongside the pillar which is in a right angle with the ground to inflict signals 6 3 7 Track metal gas pipe Generate pipeline orientation and track technique can be used to detect the steeliness gas pipe Some gas pipes have insulative tie in to offer the inner house an effective earth loop Locating the gas pipe under or roadside of the highroad you can use single end connect method to connect the transmitter to the valve and connect the earthing cables to the valve box s metal shelf guaranteeing to nip the line nip well can offer well electric connection You may brush and scrape the oil paint or the rust before connecting if it is necessary Sometimes one section of the pipeline may has some insulated tie in you should inflict the transmitter signal to the far forth end of every insulated tie in and the higher signal frequency should be adopted There maybe the tie in can hardly let the signal go through in some other iron pipes you may track the iron pipes in Induct way and move the transmitter to the position last detect the signal Brand together the techniques as above you can track the iron pipelines triumphantly commonly lf all the tie in of the metal pipelines
6. the coal gas the physical prospecting the line cable and so on does not have pours into the spot on the pipeline to survey the route and the burying depth 3 Inductive clamp method As one of the important accessories inductive clamp is used for inflicting the transmitter signals directly onto the objective pipelines C Different localization pattern for user to choose 70 depth test method Double loops direct reading method D Survey direct detection function E Receive survey conditio n automatically control function F The user may choose the dry cell or and the rechargeable cell according to the need G The signal 10 tiles high efficiency output guaranteeing the farther probing range and the detection depth H The automatic detection demonstrated the cell voltage Owes the accumulated unsent telegrams police and automatically power off J With Inductive clamp and headphone can recognize many same direction pipelines 2 3 Technical specifications 2 3 1 Technical specification Technical specification of Transmitter Signal frequency a Inject method 480Hz 7 7KHz and 31 KHz and CD mode b Induct mode 31 KHz c Inductive clamp method 31 KHz Output Pressure 0 400VP P automatic manual adjust due to the insulated instance Output wave shape sine wave Power source 12VDC 4 5AH in the Ni MH cell Peak output power 10W Technical specification of Receiver Power loss lt 1W Power source 12VDC 1 5AH in the Ni MH cell or 10 a
7. TT 2000 Pipeline amp Cable Locator User Manual 1 1 TT2000 Pipeline amp Cable Locator The TT2000 Pipeline amp Cable Locator consists of a Transmitter and a Receiver used in the underground utilities route locating the depth measuring and long distance tracing We adopted multicoil electromagnetism technology on TT2000 Pipeline amp Cable Locator enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline Thus TT2000 Pipeline amp Cable Locator is widely used in the telecommunication electric tap water natural gas physical prospecting town planning and so on The T T2000 Pipeline amp Cable Locator has many optional accessories thus increased their use and expanded their application scope Before use T T2000 Pipeline amp Cable Locator please read this handbook carefully 1 2 Security The safety comes first don t neglect the security problem and use T T2000 Pipeline amp Cable Locator certainly to have to follow the strict standard When uses some special methods for example sends the transmitter signal directly in the charged electric cable or poke probe in the pipeline with high pressure only personnel who have certain qualifications can do The Pipeline amp Cable Locator is usually used on the transportation busy road so when using it please
8. acting to increase e In measuring plus manual acting to decrease e choose peak value valley value orientation to measure it is tolerated as automatically optimize accommodate estate automatically plus accommodation is 1 99 press Jto enter manual acting accommodation estate to measure the depth of the pipeline Light tone up the LCD s well regarded tune press backlight button to tune on off Inductive lamp 1730 30 99h route Depth ba Result 00 1320 1O0em 1280 5 1 3 Cell status Show cell states continually receiver uses picture to show pressure altogether there are files you must recharge it in time when it appears H when it is lower than 10V the LCD will give an alarm and will automatically tune off after 3 seconds 5 1 4 Route peak value valley value In Inject Induct mode to press route to choose plane antenna for peak value response and you can also choose uprightness antenna for valley value response The precision of peak value is much higher than that of valley value therefore peak value response must be used in ordinary orientation you can use valley value response to check it or to do quick track 5 1 5 Plus control Indicating currently signal s blow up value by amplifier plus percentage to show it on the top left corner 5 1 6 Backlight Press this button to tune on the light press again to tune off 5 1 7 Figure display It shows th
9. are insulative you cannot locate it by generate method one way is to use extend in method to locate the pipeline tie in that is extend the transmitter s forepart into the pipeline in order to locate the pipeline tie in and then make the transmitter perpendicular to the pipeline searching apex and valley response at every tie in to nicety locate to the pipe 7 1 Check up Both the transmitter and receiver have rechargeable batteries inside you must recharge it before using Note There are two chargers one for the transmitter one for the receiver the charging methods are due to the charger instruction 7 2 Elimination For common malfunction Examine and Repair for the malfunction To measure the pressure of the charger receptacle with No display with du du noise low cell multimeter prevents short circuit if it is lower than 10 5V it must be recharged The display is not clear when opening or during the operatin j S j j low cell As above process the light is not enough or it does not work the signal is too feeble Press E The value shown is on the low side when testing the route Check the transmitter the signal isn t loaded output line iR ABES The rating with In meth Operating with Induct method transmitter isn t placed over can measure the signal distance sda The transmitter should the pipeline from the transmitter within 50 be placed over the meters cannot measure
10. e and pipes are considerable Make sure the extent including the edge belt of it 5 3 3 2 Gridding search Park the transmitter on each point of the extent in reasonable alternation do gridding research in order to detect the ignored pipelines which detected by no power research and other pipelines 5 3 3 3 Track orientation and depth measure Inflicting the transmitter signals to the pipelines and the cables this can be linked For example the container the valve the streetlights and so on track the part out of the extend and mark it For the pipelines need to be identified you can track them till the well cover streetlight and so on and then you can inflict the transmitter signals back to the extent Do orientation and depth measure to all the key points and characteristic points of each pipelines of the area mark them and note the relevant pipeline information and detect results And then coordinate the data to do the pipeline distributing map 6 1 T shape pipeline detection As long as you had made tracks for the pipeline and marked you can track again along the pipeline with the receiver but this time you may track one step distant from one side of the pipeline which has already been tracked and make the receiver run parallel with the pipeline The locator cannot detect the signal send by the main pipeline or the signal is little but the response to the branch pipeline is in evidence The most reliable method for loca
11. e helpful for the operator to distinguish whether the pinnacle pulse figures that there s a connection box 6 3 4 Metal protective fence The cables usually burying under the ground of the outside of the metal protect fence of the highroad the signal will coupling to the stretch metal protective fence It is difficult to track for the metal protective fence is near from the transmitter under layer antenna Taking up the receiver and hold the under layer antenna parallel with the metal protective fence overcoming this difficulty is easy 6 3 6 Street lighting cables The transmitter signal is always connected to the metal pillar If it is cement lamp standard unless the lighting cables can be grounded via connecting to the examine and repair shelf or you need to connect the transmitter signal with the lighting cables metal shield Knowing the relevant position and depth of the lighting cables along with the other street establishment of the same lighting system is quite helpful for tracking lighting cables one connect point may inflict signals to the cables of a large piece of area It is viable to inflict signals to other electric power cables by using lamp standard but the signal may be very little for it maybe had transmitted for a long distance before it returned to the transformer substation and it must stream again from the system Here we can adjust the transmitter to high output power mode and tune up the output power This method
12. e pipelines And you can locate the pipeline at least 30 meters away from the transmitter Note The transmitter will send radiation signal to the air and pipelines So at a distance of the shooting near the local workstation machines there might be some problems in order to determine the receivers are positioning themselves rather than direct pipeline to receive a transmitter air signal to the transmitter side of the movement may be one or two step if the response from the receiver is moving to see pipelines said receiver and the distance between the location of fire planes Another method is to directly target transmitter receivers the receivers then respond if the same or increase said receiving the air signal receivers such as the emergence of such a situation should be investigated to reduce transmitter power and reduce the sensitivity receivers receivers may need to be 50 meters away from the transmitter 9 3 1 4 Inductive clamp As one of the most important accessories it can directly inflict the signal to the objective pipelines Inductive clamp can inflict all kinds of signals safely with continuous power Please attention the transmission distance of Inductive clamp signal is nearer than that of directly link signal Insert the BNC of the Inductive clamp into the transmitter s output BNC connector jack Hitch the pipelines with the Inductive clamp make sure it s closed and then open the transmitter link well the pipeline
13. e response of the signal of the receiver it can also provide the information send by other functions 998 Route 99 Signal relatively plus value 1 99 on manual acting press f Lor Ito amend this value A automatically route measure pressit lor Ito enter manual acting to adjust the measure Miroute currently is measuring press depth jo do depth measure Peak value mode the value is biggest right over the road Press routel to enter valley value measure in route measuring the symbol change into Y Valley value mode the value is smallest right over the road meanwhile it can do route orientation 4 means the route is at the left or right side of the measurer TO Headphone method the headphone will get the strongest response intensity on the objective pipeline which has already been inflicted the transmitter signal Injeci the current mode is Inject press model to enter Induct show it is the signal s stick picture the thicker the stronger the shorter the smaller the length is in accordant with the relatively percentage 2456 Shows the intensity of the route signal 45 Use percentage to show the signal 5 1 8 Depth Press to measure the depth of the objective pipelines and it shows the test result by centimeter place the receiver right over the pipeline and make the surface in right angle with the ground adjust the delicacy to make the reading in the range press to see the depth
14. eline should be bigger than it to the close by pipeline we can recognize and track the objective pipeline by the response of the receiver But if the close by pipeline is nearer to the ground surface the receiver s response to the close by pipelines will surpass it to the objective pipelines We cannot recognize and track the objective pipeline only by the receiver s response so we must use direct join method 6 3 Ordinary instances in detection 6 3 1 Track the cables from tie in or connection box Before inflicting transmitter signal it is necessary to take the common tie in apart in order to track the objective pipeline If you want to track all cables start from the connection box you may operate the transmitter at the Induct mode put the transmitter by one side of the connection box in line with the cables tracked 6 3 2 Long distance cable track In order to transmit the transmitter signal long enough distance it is necessary to take the earth connection of the cable off When the tie in or connection be earthed because of the safety or the prevent thunder protection electric emerge avoid overloading discharge ware is used to replace the earthing of the tie in or connection so as to protect the cables making the uninterrupted orientation possible 6 3 3 Tie in pinnacle pulse Most cable tie in or connection may produce a pinnacle pulse at the response to the receiver working experience and the realization of local situations ar
15. ent through a straight line conductor it has a coaxial alternating current magnetic field around this conductor puts a loop in this magnetic field it will Induct the same frequency alternating current in the loop the Induction tension size is decided by the position of this loop in magnetic field when magnetic line direction is parallel to the loop the loop Inducts the voltage horizontal ponderance is biggest like the chart 3 3 left shows When the loop is vertical to the magnetic line direction the Induction voltage horizontal ponderance is smallest like the chart 3 3 right shows From this can judge the route of a cable faradi sm faradi sm AA Ah 1 loop loop CHE AN metal pipe metal pipe 3 2 2 Principle of surveying pipelines burying depth There are two same horizontal loops laying in the receiver the distance between them is known sees chart 3 4 obtain the signal strength of the loop over the surveying route according to the electromagnetic theory may calculate the burying depth size of unknown goal pipeline conversely According to the Induction electricity faradism difference to calculate burying depth of pipeline Signal Intension 4 1 Test Every TT2000 has to be tested before leaving factory with eligible certificate 4 2 When using the cell must have sufficient electricity concrete operation methods as below 4 2 1 Turns on the instrument to let the cell discharge until the cell symbo
16. i q La O page A o mp eim 7 Ae De md RR pia Ca gra o Sp TO pg Peq E pm A O O depth measure at the place where the response of two signals are accordant Place the receiver right over the pipeline and the machine s surface must be in a right angle with the pipelines and the ground adjusting the sensitivity to make sure that the number is within the measure range Press depth to show the depth press again to return to the former mode If it turns out a strong radiate place then there may be a radio station meanwhile you may measure the depth by making the antenna 5cm higher than the ground detract 5cm from the depth shown to know the pipeline s depth If you doubt about the result you may check again by making the receiver 0 5m higher than the ground if the result raise 0 5m it proves the former result right The depth measure precision can reach 5 if the situation is proper But the operator is impossible to know whether the situation is proper or not So we must adopt some techniques as follows to check some key reading Is the pipeline route straight At least it must be straight in 5 meters at the both sides of the measure point Is the signal stabilizing in 10 meters If it is stabilizing you may do depth measure at the former measure point Check whether there is a close by pipeline with strong signals at the distance of 3 or 4 meters to the objective pipelines It is the ordinary and most serious cause of error in de
17. l 5 3 1 2 Direct connect method Direct connect method is fit for tracking the cables water pipes and gas pipes distribute systems Link the connect cables to the transmitter output jack one red line to the objective pipelines eliminating the rust if it is necessary to guarantee good electric contact Another black line link to the grounding point it may be several meters distant from the objective pipelines and had better be in a right angle with the possible route of the objective pipelines The transmitter LCD may show the value of the output electricity lf the output electricity is too small you must check the grounding situation of transmitter and the objective pipelines change the grounding position or water the dry sand if it is necessary 5 3 1 3 Induct method In the transmitter there s a transmit loop you can directly Induct the signals onto the pipelines under the transmitter for the deeper objective pipelines the efficiency is low this method is usually used at the place where the depth is less than 2 meters What should be attention is the signal can not only Induct the objective pipelines and also do to close by pipelines Don t use Induct method to inflict the signal to the well insulated pipelines unless the two ends of the pipelines can effectively ground Turn on the transmitter power supply place the transmitter right over the pipelines and make the transmitter in a line with th
18. lize on the menu into X at this moment the terminal voltage of cell is 11V Attention don t let the cell discharge excessively 4 2 2 Meets the alternating current at this moment the indicating lamp is not bright then meet the cell at this moment the green light is bright 4 2 3 Insert the BNC of the charger into the BNC connector jack the red light shines When charging is over the red light is bright 4 2 4 Controls total duration of charging in 5 6 hours 4 2 5 When charging don t have to separate the alternating current or to insert and pull out the plug otherwise must repeat 4 2 1 4 2 4 processes Before use the TT2000 Pipeline amp Cable Locator please read this handbook The pipeline amp cable locators encasement listing A Transmitter B Receiver One C Take along bag One D User manual One E Transmitter charger One F Receiver charger G Earthing stick H Output line One Inductive clamp One J Headphone One 5 1 TT2000 pipeline cable locator receiver Synopsis 112000 Pipeline amp Cable Locator 5 1 1 On off Press the power source button to open the receiver controls the on and off press again to close it Notice don t press the button too long 5 1 2 Mode Key press operate mode is adopted the receiver is mainly made up of 7 functional button to control on and off AARE for choosing signal loading mode Inject Induct headphone e In measuring plus manual
19. lkalescency batteries Biggest test burying depth 4 5 meters normal instance The test burying depth error lt 0 05h b5cm h is pipeline depth The test route error lt 5cm normal condition The test insulated error lt 25MQ Test the route and the efficient depth with Inject method 25Km normal instance Test the route and the efficient depth with Induct method 23Km normal instance Note The objective pipeline has no insulated failure or other interruption in the above mentioned range in the normal instances 2 3 2 Environmental request Operating temperature 20 C 5 0 C Storage temperature 40 C 70 C Relative humidity 10 90 Atmospheric pressure 86 106KPa Environment noise lt 60dB 2 3 3 Physical property Name Weight Kg External Dimensions mm Transmitter 3 348x236x180 Receiver 2 5 645x262x130 Entire machine gross weight 13 3 790x415x260 3 1 Transmitter s principle of work The transmitter is controlled by the miniature processor chip with large screen LCD in English choose function in the menu when being used examine the loading state and the condition of the cell if the pipeline has the high residual voltage then cut off the connection with the pipeline and alarm 3 2 Receiver s principle of work The receiver is controlled by the miniature processor chip with large screen LCD in English and it can examine cell status when boot strap 3 2 1 Search route When alternating curr
20. o load signal 5 3 Detect methods The TT2000 Pipeline amp Cable Locator uses the power supply to track and orient the transmitter signals 5 3 1 Surveys Methods The transmitter sends the special signals to the pipelines by direct Inject or Induct coupling and then do orientation and track 5 3 1 1 Inflict transmitter signals The operator must choose the technique to inflict best transmitter signal and the least coupling domino effect Guaranteeing send enough track signals use lowest signal to save cell power and reduce coupling effect Two ways of inflict transmitter signals in common use direct connection and Induct divisor Whatever way to choose you must assure that the objective pipelines can distribute a certain distant signal electric current loop or the locator cannot detect the objective pipelines The transmitter can contact the capacitance Earth the pipelines if it is necessary Enter into the signal output estate automatically if there s no remain pressure on the pipelines if there s high pressure you will hear an alarm meanwhile the measure will not continue please measure again after finding out the causes Note If the pipelines which under the transmit point insulated block value is small less than 1kQ or the measurement is 00 or it is near the cable tie in box then the signal may leak or cannot bring Induct current So you can properly move the transmitter to get the strongest Induct coupling signa
21. pipelines 2 Don t do depth measure at the pipeline crook or nearby the T shape branch pipe you can get best precision measure 10 meters depart from the pipeline 3 The depth measure is unfaithful when there s intensive interfere or the transmitter signal has already been coupling on the close by pipelines 4 Avoiding inflict signals using Induct divisor in depth measure if you have no alternative the transmitter must leave 30meters away from the depth measure point 5 If the transmitter signal is transmit to the near by pipelines you should inflict the signals onto the objective pipelines by both sides connect method 6 Two measure ways speediness measure and precision measure press depth two times to enter precision measure Direct reading divisor is in common use 7 When detecting depth the signal value should be over 3000 and the value fluctuate is small a Direct reading method It can do depth measure of 4 5 meters It s simple and convenient the precision measure is high when there s no interfere But it has the shoricoming of a sort of anti jamming ability Signal Intension q e I m E Ta Em h E eS terest INE E om Rar ae EE ho pr E Lg Ea mM au gq j i pt i e o o ae ae We a E O fonts Gate Me e xIts mn Bo ps Pp s Si Ht yt e ahs ih a gt a E dad lr i re Fl I EE ae ye ee a aa Lg Tat Po Edo Bea do el Pet 2 ee if fs we Pr ado E Fe A fu dP F
22. pth measure The strong signal of close by pipelines may cause 50 error To do depth measure a little far away from the pipeline orientation points the smallest is the most pinpoint one b 70 method If you have doubt in the result of direct depth measure you can use 70 method to check this kind of measure is efficiency because it adopts reading several different points to do depth measure deeper than 20cm When the receiver is right o pipeline make the reading a proper number while the receiver is in a right angle with the ground and then move the receiver left and right to decline the reading to 70 of the value Mark the two points and measure the distance The distance is right the depth of the pipeline Note Do not use this method when the depth is less than 20cm If the results of the two depth measure are close it tunes out that the precision of the depth measure is guaranteed 70 method is widely adopted by the professional pipeline detect companies for its high precision of depth measure and efficiency in anti jamming 5 3 3 Fieldwork procedure The TT2000 pipe cable locator can do orientation for all the metal pipelines and cables of the extent So all the information about the depth and positions of pipelines are helpful for designing new pipeline pave project 5 3 3 1 Preparation Work over the locale before operating the pipe amp cable locator The well cover street lights and all the signs refer to cabl
23. s the LCD may show the left right arrowhead to the pipeline position Tune back to the peak value response mode periodically so as to check the exact position of the objective pipelines Use peak value mode to do orientation and mark it And then tune back to the valley value response mode note down the valley value response position if they are accordant it can be considered pinpoint If they are not accordant then it should be not pinpoint Attention the two signs are at the same side of the objective pipeline the fact position of the objective pipelines is near the position of the peak value response A Pipeline zero response c Headphone method It has a good effect to pipelines general cannot be recognized such as many parallel pipelines aerial cable The headphone will get the biggest response intensity on the objective pipelines which have been inflicted transmitter signal When the direction of the arrowhead of headphone is parallel to the pipeline direction the signal is the biggest The other way round the signal is the smallest 99 A Route a 1780 30 5 3 2 2 Depth measure As long as inflicting the transmitter signal onto the pipelines you can do depth measure to objective pipelines Pay attention to the proceedings hereinafter in operating 1 Do depth measure in the middle part of the pipeline the depth of detecting must be within the depth detect extension It s the sticking point for big diameter
24. s so that the signal can be transmitted to the pipelines It is normal that there s buzzer or shake it doesn t do harm to the instrument Don t touch the BNC when the Inductive clamp clamps the electric power cable Though the insulated cable has no real earthing point as lone as the pipeline buried a certain distance underground can support a capacitance coupling it can track the insulated cable as well The transmitter cannot earthing when using the Inductive clamp to inflict signals In many instances people always choose Inductive clamp method instead of direct link method as the working mode of inductive clamp method is like the pipeline has already been slice off and link the transmitter to the two incisions 5 3 2 Use the transmitter to do orientation and orient the depth Since you successfully inflict the transmitter signal onto the objective pipelines you can track and do orientation to the pipelines with the receiver The position and the depth are the most important information of underground pipelines 5 3 2 1 Use the transmitter to do orientation for the objective pipelines Transmitter boot strap interface Smart Tech 99A Route A i 30 TT2000 provides three detect modes peak value and valley value and headphone a Peak Value Method Peak levels in response to two days of receiving a target pipelines signal strength level the antenna and top receiver antenna signal intensity for the poor response Peak
25. t electric Press button requiring 8s backlight to save energy 5 2 1 Keyboard oo On Off You can see the boot strap interface after you press the and it will do detection to the cell use for choosing signal loading mode Inject Induct or back to the signal accommodate estate in Inject mode transmitter test the circuitry firstly to do left pressure measure and insulated characteristic measure Diversion interface Choose Induct loading mode Increase Signal Intension Reduce Signal Intension Transmit Press the Transmit to load signal after choosing Inject loading mode a The interface at Inject loading mode Pipeline Examination Pipeline Insulated resistance gt 1 Mo 5 2 2 LCD LCD shows output signal mode and kinds of functions 5 2 3 Cell The transmitter can give cell status directions on the LCD if the cell power is low the cell sign will flash and output break off signal before turning off the transmitter can be filled with 10 alkalescency cells rechargeable cells 5 2 4 Connect cables Crewel cables with line nip can directly connect the transmitter signals with the objective pipelines the red nip link to the pipeline and the black one link to the ground 5 2 5 Earthing stick To earthing and to provide signal loop 5 2 6 Inductive Clamp It is a good method to recognize many same direction pipelines especially the lines in the pipes You can directly nip the objective lines t
26. the ik AFR2ZI5 FAR The pipeline signal outta 50 meters transmitter isn t placed parallel to the pipeline 5 The receiver cannot receive The transmit intensity isn t To adjust to the proper signal when using immit method adjusted well transmit intensity The signal output pin doesn t As above J i p Stick the pin well in stick in well When using Induct method or When signal outputting ad Use it after it has been 7 immit method can hardly whelt digplays or you fully recharged receive signal must get it recharged y q 7 3 Maintain service All products and the accessories of our company had been well tested when designing producing and before leaving factory guaranteeing the trustiness of the performance and the choiceness of the quality If you have any problem in operating please first consult this user manual If you need more consultation please contact the after service department 7 4 After service promises Our producis carry out maintaining for life outer the maintaining period you only have to pay for the cost charge We respond to the clients advices and ideas to the product quality in 24 hour
27. ting the pipeline is to inflict the transmitter signal to the end part of the branch pipeline The signal streams from the branch pipeline to the main pipeline and then streams between both sides of the main pipeline s double directions The airframe surface is in a right angle with the main pipeline you can track the signal along the main pipeline the receiver will response to it as zero values valley top right over the tie in of the T shape branch pipeline The reverse position of the valley is the nicety place of the T shape branch pipeline s tie in 6 2 Parallel pipelines detection In pipeline detection the parallel pipelines is the sort of universal instance in the area where the pipelines are dense the receiver may always receive the interfere signal from the close by pipelines it may brings us the difficulty in recognizing and tracking the objective pipelines and effecting the precision of orientation and depth fix Therefore we must adopt some methods to the best of our abilities to minish the influence of the close by parallel pipelines coupling signal First we d better not use the Induct method in the area where the pipelines are dense but to use the coupling ability of direct join method to inflict transmitter signal In such instance wed better use peak value response mode orientation measuring the depth by 70 method so as to reduce the windage In commonly instances the response of the receiver to the objective pip
Download Pdf Manuals
Related Search