Home

Manual

1. 1 Mount the Junction Box with the screws provided to permanently install the Junction Box beneath the dashboard on the passenger s side of the vehicle or on the center side post between the front seats Diagram 2 2 The Junction Box must be protected from dirt and moisture and must be afforded adequate space for cooling There must be sufficient space to allow for connection of all cabling Visor Speaker Display Privacy Power Microphone Monitor Handset Jack Diagram 3 Rapid Control Hardware Charger Module Upgrade Diagram 4 3 Route the cables out of the way to avoid physical or visual obstruction Allow sufficient slack in the cable to allow smooth operation of all controls 4 Connect the Control Module Speaker Visor Microphone Display Monitor and Power cable connectors to their respective corresponding connectors in the Junction Box as shown in Diagram 3 above C Power Cable installation 1 Route the black lead of the main power cable to convenient chassis ground and the red lead to the positive supply voltage connection points If it is necessary to penetrate the firewall use an existing opening Caution 1 The Hands free unit should be used with a negative ground system only 2 If necessary drill a new hole approximately 9 16 3 5cm in diameter Make sure that there is enough clearance on the opposite side Insert a grommet into the hole to prevent damage to the power cable 3 Cut the black l
2. Main Menu Voice amp Speed Dial Call Log amp Dial Phone Book Inbox SMS Settings 2 Recent Calls Dialing 1 The last 10 Dialed and last 10 Received call numbers will be saved to the Dialed Calls and Received Calls 2 Using the Scroll Wheel select the desired location and press SEND Answer 3 To end the call press END Escape 4 You can delete all your Received or Dialed call logs by selecting Main Menu Call amp Log Then select Delete Out log or Delete In Log 3 Phone Book Dialing Use the Scroll Wheel to display the Main Menu Phone Book Scroll to the desired Name Select then use SEND Answer to start a call Advancelec Phone Book 4 Voice Dialing ONLY available with voice activated phones Scroll to Main Menu Voice amp Speed Dial Voice Dialing and select 15 ACVANCEIEC Main Menu Voice amp Speed Dial Call Log amp Dial Phone Book Inbox SMS Settings AdVANCEIEC Voice and Speed Dialing Voice Dialing Speed Dialing Speed Edit Shortcut option From idle state press and hold down END Escape key for 3 seconds You will be prompted to SAY A COMMAND Use the voice dialing feature of the Car Kit in the same way as you would with your phone 5 Speed Dialing The Speed Dial facility holds 28 numbers for each paired phone Five different phones can be paired to the car kit at one time To enter a New Contact to the speed dialing you have 2
3. options 1 In Main Menu Voice amp Speed Dial Speed Edit Scroll to an Empty location and select 16 advancelec Voice amp Speed Dial ACVANCEIEC Speed Edit Select Edit Name scroll through the letters and type the name Press END Escape to return to the Speed Edit Screen advancelec Edit Speed 01 Joe Moore Edit Number PASTE SAVE DEL Select Edit Number and scroll through the numbers and type the desired phone number Press END Escape to return to the Speed Edit Screen To save the contact select Save before exiting 17 advancelec Edit Speed 01 Joe Moore Edit Number PASTE SAVE DEL 2 Using Copy and Paste You can copy a contact from Phone Book Dialed Calls or received Calls AdVANCETEC 305 555 5555 Joe Moore Copy SEND Paste it in a speed dial location ACVANCEITEC Edit Speed 01 Joe Moore Edit Number PASTE SAVE To save the contact select Save before exiting To Dial from the Speed Dial memory you can 1 Scroll to Main Menu Voice amp Speed Dial Speed Dialing Scroll to the desire location and press the scroll wheel to select or SEND Answer 18 2 Push and hold down SEND Answer until the Speed dial menu appears Press the scroll wheel to Select Advance Features available during an active call There are 3 features available during an active call 1 Changing Volume Speaker symbol Adjust volum
4. AdvanceBlue Installation and User Manual Bluetooth Car kit Part No AT8000A 3 Bluetooth W AN advancelec y INDUSTRIES INC 1150 NW 163 Drive Miami FL 33169 Tel 305 623 3939 Fax 305 623 3996 www advancetec com Menu Car Kit Part Numbers and optional extras Warnings Speaker Installation Instructions Junction Box Installation Power Cable Installation Entertainment Mute Mounting of Control Module Microphone Installation Display Monitor Installation Control Module Detail Pairing the Phone to Bluetooth Disconnecting Bluetooth Reconnecting Phone Phone Book Download Receiving a Call eCall Waiting Making a Call Manually Dialing Recent Call Dialed Phone Book Dialing Voice Dialing Speed Dial amp Set up Advance Features during Call SMS Text Messaging Additional Phone Settings Reset System Power Disconnect Rapid Charging Privacy Handset Specifications Page 3 Page 4 Page 4 Page 4 Page 5 6 Page 6 Page 6 Page 7 8 Page 8 Page 9 Page 9 10 Page 10 Page 11 Page 11 12 Page 13 Page 13 Page 13 Page 13 Page 14 Page 14 Page 15 17 Page 17 18 Page 18 Page 19 Page 20 Page 20 Page 20 Page 21 Page 22 The Bluetooth Wireless Car Kit Model AT8000A includes 1 AT8010A LCD Display 2 AT8011A Mounting Post with suction cup 3 AT8012A 4 Piece mounting bracket 4 AT8013A Control Module 5 AT8243A Junction Box 6 AT8230A Visor Micro
5. communications equipment in the area over the air bag or in the air bag deployment area If the communication equipment is improperly installed and the air bag inflates this could cause serious injury It is recommended that the installation of the vehicle communication equipment be performed by a professional installer technician trained in the requirements for such installations An air bag s size shape and deployment area can vary by vehicle make model and front compartment configuration for example bench seat vs bucket seats Contact the vehicle manufacturer s corporate headquarters if necessary for specific air bag information for your vehicle INSTALLATION INSTRUCTIONS A Speaker Installation 1 Mount the Speaker beneath the dashboard on the passenger s side of the vehicle out of the way of the passenger 2 The Speaker should be located more than four feet from the driver 3 Do not mount the Speaker on the dashboard or the rear window shelf 4 The Speaker includes a mounting bracket which is used to permanently mount the Speaker in place while permitting it to be tilted to a desired angle 5 Loosen the thumbscrews on the side of the Speaker and using the mounting bracket as a template drill the necessary mounting holes and secure the bracket with the self tapping screws provided 6 Position the Speaker on the mounting bracket and secure it by tightening the thumbscrews Diagram 1 B _Junction Box Installation
6. e Up or Down by rotating the Scroll Wheel 2 Dialing numbers _ key board symbol 3 Phonebook access Book symbol ACVANCETEC Talking 305 555 5555 Joe Moore Select each of the above options using your control wheel Go back to your previews option by pressing END Escape Incoming SMS Text Messaging 1 Once the phone is paired the car kit will be in the Stand By mode 2 In the Stand By mode an incoming SMS Text Message will show on the Monitor with an envelope and down arrow NOTE SMS Text Messaging function is only be available if your phone supports SMS 3 To read the message click on the envelope by scrolling to the envelope with the control module and press on the scroll wheel 19 advancelec Motorola Phone Old amp New SMS text messaging To read an Old or New SMS text messages select Inbox SMS on the main menu Note Once the New Messages are loaded they will automatically be moved to the Old messages directory advancelec Main Menu Voice amp Speed Dial Call Log amp Dial Phone Book Inbox SMS Settings Select to read New or Old SMS ACVANCETEC Inbox SMS Read New SMS Read Old SMS 20 The following additional settings are accessible through the SETTINGS menu ACVANCETEC Settings Paired Phones New Pair Brightness Load Phone Book Volume Set Phone Mode Software Languages Reset System Brightness Monitor brightness setting
7. ead to the desired length 4 If the connection is being made under the dash or in the vehicle cabin connect the black lead directly to the chassis of the vehicle Note Do not connect the black lead to the negative battery terminal The car could be damaged if there were a malfunction in the vehicle s electrical system 5 Cut the red lead to the desired length This lead will be connected such that it has positive supply voltage at all times even when the vehicle is turned off 6 If the connection is being made under the dash or in the vehicle cabin connect the red lead to a positive supply voltage point 7 If the connection is being made in the engine compartment or directly to the battery connect the in line fuse holder between the red lead of the power cable and the desired positive voltage connection point 8 Route and connect the green lead to a convenient ignition switch supply point in the vehicle Green To Ignition Switch gt Orange To Vehicle Stereo Black To Vehicle Chassis Groud Red To Vehicle Supply Voltage Diagram 5 Entertainment Mute If the vehicle s stereo system supports an external muting feature route and connect the orange wire to the car stereo system Otherwise the orange wire may be left unconnected and cut off or tied out of the way NOTE The Car Kit supports an Entertainment Mute function when connected to a car stereo system that provides for external muting This functio
8. ice will not be heard Diagram 8 NOTE The car kit is supplied with one of the above two microphones They are both designed for the car kit and both work equally well 2 To avoid visual or physical obstruction route the microphone cable down inside the door frame molding Allow sufficient slack in the connector end of the cable to reach the Junction Box 3 Plug the connector side of the external microphone cord into the Junction Box as shown in diagram 3 above F Display Monitor Installation Note Two options are included for mounting the Display Monitor 1 Slide the flat end of the suction cup mounting post or the flat end of the flexible mounting bracket both supplied into place on the back of the Display Monitor 2 Attach the suction cup onto the front wind shield or the flexible mounting bracket in a convenient position as the case may be ensuring that the Display Monitor does not obstruct the drivers view Dress the surplus cord out of the way See Diagram 9 over the page Diagram 9 NOTE Before operating the Bluetooth car kit it is important to familiarize yourself with the operation of the Control Module as shown SEND Answer END Escape Pairing the phone to the Bluetooth Car Kit Before you can use this car kit you must link pair it to your phone NOTE This Bluetooth Car Kit can only be used if you have a Bluetooth enabled phone Initial Pairing 1 Turn on the car ignition and the Ca
9. n is compatible with systems that mute the audio output when the control line is connected to ground D Mounting of the Control Module 1 The Control Module can be attached to the gear lever parking break or other similar devise with the Velcro strip supplied as shown Diagram 6 2 To attach the Control Module to a flat surface remove the Velcro by pulling on one end of the Velcro to slide it out Screw the flat ribbed plate supplied with the Control Module in position in a convenient place with the ribs facing up within easy reach of the driver using the 2 screws supplied Align the Control Module over the ribbed flat plastic and press down until it snaps firmly into place Diagram 7 3 Once attached pass the surplus cord out of the way so that it is not visually or physically obstructive Caution Make sure that there is sufficient slack in the cable to allow the free movement of what ever it is attached to without stretching the Control Module cable E The Microphone installation Selecting the correct position for the microphone is vital for the successful performance of the hands free unit 1 The Microphone should be mounted either on the sun visor directly above and facing the driver or on the headliner just above NOTE The microphone has a noise cancellation function and so the point as indicated in Diagram 8 below must face directly towards the driver If it does not face the driver the driver s vo
10. ne connector on the other end of the cable into your phone 3 The battery symbol on the monitor will blink indicating that your phone battery is being charged To Junction gt Box Privacy Handset 1 The Privacy Handset Part AT7107A is available as an optional extra 2 Plug the privacy handset RJ45 connector into the corresponding plug as shown in Diagram 3 3 To have a private conversation lift the handset and the audio will switch from the hands free speaker to the handset 4 When the handset is lifted an icon will flash in the right top corner of the display monitor indicating that the handset is out of the cradle Talking X 305 555 1212 5 To resume a hands free conversation replace the handset into the cradle 22 Specifications Electrical Specifications 1 Power input 12VDC 24VDC 2 Operating temp 20 70 3 Storage temperature 30 80 Charging Output 5V 450mA with the AdvanceTec charging cable 5V 100mA with a regular USB cable Audio Specifications 1 10W loudspeaker 2 Full duplex audio digital transmission 3 Noise suppressions cho cancellation DSP Bluetooth Specification 1 Bluetooth 2 0 EDR 2 Tx Power Bluetooth Class 2 3 Frequency Band 2 4G 4 Supports a Hands free HFP b Headset HSP c Phonebook Access PBAP profiles d Supports SMS with some of phones LCD Specifications 1 Outside Dimensions 103mm L 103mm W 2 Display font size 6 09 mm 3 Format 128
11. ownloaded Up to 1000 contacts can be downloaded for pair number 1 Up to 1000 additional contacts are shared between the users 2 5 3 If 2 or more users share the same car kit then user 2 5 will have to reload their phone book each time they wish to access it The car kit will save the phone book of the last phone paired 4 Select Cancel to stop download if no activity was noted after 1 Minute NOTE If the downloading process starts and then stops this is an indication that the Car Kit does not support this function with your particular phone Receiving call 1 To answer a call press SEND Answer 2 To reject a call press END Escape 3 Caller ID will show on the display if the caller s name and phone has been entered in the Monitor phonebook If the name and phone of the caller has not been entered the caller s phone or Unknown will show Call Waitin 1 During a call in progress you can accept an incoming call by pressing SEND Answer 2 To reject an in coming call press END Escape 3 To scroll between 2 calls press SEND Answer The active call will be highlighted 4 To end an active call press END Escape Making a call A call can be made in the following ways 1 Manually Dialing 1 Use the Scroll Wheel to display the Main Menu Call Log amp Dial Dial and select 2 Select the desired numbers to dial and press SEND Answer 14 ACVANCETEC
12. phone 7 AT8229A Visor Microphone 8 AT8231A Speaker 9 AT8232A DC Power cable Optional Extras 1 AT8110A Mini USB Rapid Charging cable 2 AT8111A Micro USB Rapid charging cable 3 AT7107A Privacy Handset with Cradle Note A properly installed Hands free Car Kit will minimize service calls and equipment downtime Because of the wide variations in vehicle design these instructions should be modified to suit each particular installation Before beginning the installation process determine the locations for the mounting of the LCD Display Mounting Post with suction cup Control Module Visor microphone Speaker and Junction box Consider the following guideline when planning the installation e DO use all mounting hardware provided e DO ensure that cables are not placed under stress e DO follow proper and connections e DO crimp connectors securely e DO NOT attach components to any part of the vehicle that is not rigid or is subject to excessive vibration e DO NOT install components in areas where rain or snow can easily get into them such as next to a vehicle window which may be left open e DO NOT pass cables over sharp edges that could cause wear or tearing of cable insulation e DO NOT install components in locations where they might interfere with the vehicle operator or operating controls WARNING VEHICLES EQUIPPED WITH AIR BAGS An air bag inflates with great force DO NOT place objects including
13. phone is marked gt gt 2 Select Paired phone and then select Disconnect Method 2 Using your phone 1 Scroll through the Main Menu of your phone and select Bluetooth 2 Set to OFF Disconnect will appear on the phone screen Select OK Re Connect Phone Program your phone for Auto Connect For this function consult your phone manual 1 If the phone is already paired and was not manually disconnected when exiting the car it will automatically reconnect when you next enter the car 2 If the phone does not automatically reconnect a function of some phones you will receive a request to reconnect on the phone screen Select OK 3 If the phone does not automatically reconnect and a request does not appear on the phone screen scroll on your monitor through Main Menw Settings Paired Phones and select your phone then select connect 12 Phone Book Download 1 To download the phonebook of your phone onto the Monitor scroll to Main Menv Settings Load Phonebook ACVANCETEC Main Menu Voice amp Speed Dial Call Log amp Dial Phone Book Inbox SMS Settings ACVANCEIEC Settings Paired Phones New Pair Brightness Load Phone Book Volume Set Phone Mode 1 To download all your entries select Sim amp Phone ACVANCETEC Oni Sim amp Phone 13 2 Select Start The number of entries loading will count until all entries are downloaded The final number showing will be the number of entries d
14. r Kit will power on The software version will be displayed on the monitor 2 Enable the Bluetooth mode on your phone 3 On the Control Module press the Scroll Wheel to select the Main Menw Settings New Pair wait for message to appear 10 ACVANCEIEC Main Menu Voice amp Speed Dial Call Log amp Dial Phone Book Inbox SMS Settings 4 On your phone select the relevant option to look for a new device 5 After the phone completes the search it will display AdvanceTec 6 Select AdvanceTec and you will be requested to enter a pass code 7 The default Pass Code is 8888 ACVANCETEC 8 After successful paring your phone s name will show on the monitor If not go to Main Menu Settings Paired Phones and check if your phone name appears If yes select your phone name and select connect 11 ACVANCEIEC gt gt IPHONE 4 Nokia 5 Samsung If your phone s name does not appear then you should retry pairing 9 Once you have set up the paired link between your phone and the Car Kit the Car Kit will remember your phone s ID and will automatically connect when you next enter and start your vehicle Disconnecting Bluetooth connection The phone automatically disconnects when you are beyond the 10 meter range of the car kit To manually disconnect use one of the following methods Method 1 Using your Monitor 1 Scroll through Main Menu Settings Paired Phones The Paired
15. s from 0 100 in 10 increments Volume Set Adjust from 0 7 Languages Choose English Spanish German or French Phone Mode If some features do not work in Mode 0 try Mode 1 Software This is only needed when there has been an upgrade of the software The upgrade will be provided by AdvanceTec either in the form of a CD or on the www advancetec com website Software can be upgraded via a standard USB connector to the Junction Box or a mini USB to the Monitor Reset System This will reset the main board in the same way as after the unit is powered ON The resetting of the system will have the same effect as powering the unit ON and OFF Power disconnect If the ignition is turned OFF and 1 a call is in progress the car kit will remain ON until the call is ended 2 a call is not in progress a count down timer will show on the monitor display showing the time until the car kit will turn off To add additional time to delay the turning off click on the timer icon with the Scroll Wheel NOTE When the car kit is OFF the pressing of END Escape will turn the car kit ON even if the ignition is OFF 21 Rapid Chargin 1 To rapid charge your phone you will need to purchase the AdvanceTec rapid charger cable that matches your phone Consult your sales person for the correct part number 2 Plug the USB connector of the cable into the USB port on the junction box See diagram 3 above and the Mini or Micro USB depending on your pho
16. x64dots 4 LCD mode STN Negative transmissive Blue Mode 5 Viewing direction 6 o clock 6 Backlight color Side White 7 Viewing area 62 0mm L 44 0mm W 8 Dot size 0 40mm L 0 56mm W wW AN advancelec y INDUSTRIES INC 1150 NW 163 Drive Miami FL 33169 Tel 305 623 3939 Fax 305 623 3996

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents