New GSM Alarm System
Contents
1. to 10 wireless detectors Extra sensors not in the standard package have to be coded to the host in order to perform normally Their code cannot be empty or the same with the saved code in the host Method enter defense zone setting menu press 4 or 6 to choose sensor press 8 to find coding and then press ENTER to confirm Trigger the sensor you want to add the panel will make two beeps after receiving it And then press ENTER to confirm If the sensor has been saved before after triggering it the main unit will make four beeps and LCD screen display 10 Error Repeated code Operation figures Fig 2 choose zone number and press ENTER 241015162 0101010101010010 Normal code Trigger sensor Fig 4B the host has the same code with sensor code Error Repeated code 5 Delete Defense Zone The wireless detector can t control the main unit after it s deleted 11 Method enter defense zone setting menu press 4 or 6 to choose the sensor you want to delete Press 8 to find delete and then press ENTER Operation figures Fig 2 choose zone number Delete Fig 3 choose Delete and press ENTER 6 Defense Zone Place Setting The location of defense zone can be set in the main panel so that the panel can send correspondent alarm message There are 8 locations for alarm SOS fire gas door hall window balcony and boundary Please refer to Ch2. will call the next number automatically It will call all the preset numbers in order for 3 times If you answer the call you will hear the pre record voice You can set system via your telephone or mobile phone keypad If you hang up directly without answering the call the system will call all the numbers circularly for 3 times Press Read the alarm information Press 1 Main unit stops alarming and Arm it stops calling users Press 2 Main unit stops alarming and Disarm it stops calling users Press 3 Siren off and monitors the scene for 30 seconds for continued monitoring press 3 again to monitor for another 30 seconds Press 4 Main unit starts a 30 second two way intercom It cannot be controlled by the mobile during the time of intercom 5 Remote Control Dial the number associated to the alarm main unit by phone mobile phone and after the ringing cycle you can hear a voice prompt Please enter password If the password is right you will here Press 1 to arm Press 2 to disarm Press 3 to Monitor Press 4 to Intercom If the password is wrong you will hear a prompt voice wrong password please re enter System default password is 1234 Press 1 arm if finished successfully you will hear a voice prompt System 37 armed Press 2 disarm if finished successfully you will hear a voice prompt System disarmed Press 3 monitoring for 30 seconds to continue monitoring p
3. 01 Zone SOs 11 12 12 21 12 Fig 3 press 4 or 6 to check 08 Zone GAS l l l 11 12 12 23 13 l l l l Chapter 6 Technical Parameters List 1 Input Voltage DC12V 1A Standby Current lt 35mA Alarming Current lt 450mA Wireless Frequency 315 433MHz PT2262 EV 1527 4 7MQ GSM Frequency 900 1800MHz quad band optional Back up Battery NI HI AAA 6 DC7 2V Siren Volume 110dB List 2 Alarm Defense Zone Information m pe e ee ee e m feee fee ee e e Chapter 7 Components List Main panel 1 pc Remote controller 2 pcs Siren 1 pe PIR sensor 1 pc Door sensor 1 pc Power adapter 1 pc User manual 1 pe Chapter 8 Care and Maintenance The alarm system has excellent design and uses advanced technologies It shall be used with care The following suggestions are required to maintain 40 your obligations under the warranty terms and for prolonging the service life of the system lt Place the control panel and all parts and accessories out of children s reach lt Keep the alarm system dry Rain humidity and various fluids or moisture all will corrupt the electronic circuit Do not use or place the alarm system in dirty locations otherwise the electronic elements will be damaged Do no place the system in excessively hot locations High temperature will shorten the service life of electronic equipment damage batteries deform or even melt some plasti
4. C ie ND GND G ND Switch for internal battery SIM card slot Please pay attention to the direction arrow marked on the slot LOCK OPEN Do not insert or take out the SIM card when the main unit is power on Chapter 3 Initialization Correct initiation of the main panel is important to its normal working and lifespan 1 Connect the wired accessories that you need 2 Insert SIM card 3 Connect the power adaptor The main panel will start self inspection and the POWER indicator LED will flash once If this LED does not light on you need to restart the panel Please do it at least 10 seconds later as repeated power on and off in short time is bad to the panel s service life 4 The main panel will flash every 3 seconds after searching GSM network successfully 5 Turn on the battery switch 6 Check the GSM signal icon on the LCD screen Signal less than 3 lattice will affect the normal performance Please put the main panel at the place with good GSM signal Chapter 4 System Settings 1 Enter Settings All the settings have to be done in setting status Press 2 8 4 6 to turn up down left right Enter setting status in the state of disarm input 6 digit password system 7 default 888888 and then press ENTER The main panel makes a beep and SET indicator lights on The screen shows remote controller setting Fig 2 please enter password a 2 Add Remote Controll
5. New GSM Alarm System M dp ee fates seamed 5115 CH gy War 4 I A on 4 bay J User s Manual Profile For a better understanding of this product please read this user manual thoroughly before using it Chapter 1 Features Chapter 2 Alarm Host Introduction Chapter 3 Initialization Chapter 4 System Settings Enter Settings Add Remote Controller Delete Remote Controller Coding of Defense Zone Delete Defense Zone Defense Zone Place Setting Defense Zone Mode Setting Siren Setting for Alarm oe Se ee ee Alarm Delay Setting po Alarm Number Setting p p Delete Alarm Number SMS Number Setting Delete SMS Number pm pm pm gt Ww N Network Center Setting po On Voice Recording Record Play p bem IW System Date Setting po CO System Time Setting n Timely Arm Setting ho Timely Disarm Setting N p Wireless Control Setting N N Wireless Siren Coding 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Wireless Siren Encryption Wireless Control for Home Appliance Change Operate Password Change Program Password Arm Delay Time Setting Alarm Delay Time Setting Voice Prompt Function Siren Prompt for Remote Controller Backlight Setting Siren Setting in Emergency Help Mode SMS Reply for Arm Disarm Language Setting Factory Reset Forget Password Chapter 5 Operation Instructions E a a a ae i
6. Press 6 to choose delay alarm Input the time you want to set and save it Operation figures Fig 1 enter settings menu Fig 3 press 6 to choose delay alarm Fig 4 input time and save it Please input 15 29 Voice Prompt Function This main panel has voice prompt function When user press arm or disarm of the remote controller it will give voice prompt System default for the prompt is on Users can set it according to actual needs Method enter settings menu then you ll see operate password Press 6 to choose voice prompt and choose enable or disable Operation figures Enable DIREI 30 Siren Prompt for Remote Controller Turn on this function the siren will sound a short beep each time you press the remote controller System default is off Method enter settings menu and then you ll see operate password Press 6 to choose siren prompt and choose enable or disable Operation figures Fig 1 enter settings menu Fig 2 you ll see operate password menu Fig 3 press 6 to choose siren prompt a 31 Backlight Setting The backlight of the LCD screen and keypad will be off automatically after a certain period of time when there is no operation on the keys Users can set it keep on if required System default is disable Method enter settings menu
7. T Out Arm Home Arm Disarm Answer Alarm Call Remote Control Emergency Help System Dialing Function Alarming Record Checking Chapter 6 Technical Parameters Chapter 7 Components List Chapter 8 Care and Maintenance Chapter 1 Features 009 0 6OOHF 9 9 HOF Elegant and advanced touch keypad for easy operation 128x64 lattice LCD screen with clock display 4 wired and 10 wireless defense zones each wireless zone supports maximum 10 sensors Support maximum 8 remote controllers Built in high volume speaker and artificial intelligent digital voice announcer Built in artificial intelligent English message 10 second automatic voice message recording Can preset 6 phone numbers when alarming system will make audio call to these numbers automatically Can preset 3 SMS numbers when alarming system will send SMS Timely arm and disarm Can be used as a wireless telephone by using keypad to make calls One key control out arm home arm arm by remote controller or telephone SOS fire gas door hall window balcony and boundary places alarm Real time delay 24 hours bypass defense zones programming function Wireless learning code easy to add additional wireless accessories Remote control the device to arm disarm monitor and intercom by phone Record checking the device can store 30 alarm records Different arm status out arm home arm delay arm and timely arm Arm by differen
8. able disarm SMS 7 Enable l DIRY Iel l l l 34 Language Setting This alarm system supports English and Chinese versions Please enter settings menu and then you ll see operate password Press 6 to choose language Then press ENTER will shift between Chinese and English Operation figures 33 English 35 Factory Reset When the system is unstable it is recommended to reset it Enter settings menu and then you ll see operate password Press 6 to choose factory setting After this operation all the settings return to factory default Operation figures Fig 2 you ll see operate password menu Fig 4 Press ENTER to confirm l l l l Restore l l l 36 Forget Password If users forget the password they can input 95175308246 under disarm status The main panel will display please wait back to default password After this operation the operate password return to factory setting 1234 and program password to 888888 Operation figures Fig 1 under disarm status Fig 3 confirm the operation Chapter 5 Operation Instructions 1 Out Arm Out arm means all the defense zones are in arm status When there s nobody at home it is required to set all the detectors working Any detection source such as thief fire or gas leakage trigger the detector the alarm system w
9. and then you ll see operate password Press 6 to choose backlight on and choose enable or disable Operation figures 30 Fig 2 you ll see operate password menu Fig 3 press 6 to choose backlight on Fig 4 choose enable disable Disable E ELE 32 Siren Setting in Emergency Help Mode System default is that when you press the emergency button of the remote controller the siren does not ring Users can set it according to the actual needs Method enter settings menu and then yov ll see operate password Press 6 to choose remote siren and choose enable or disable Operation figures Fig 2 yov Il see operate password menu Fig 1 enter settings menu Fig 4 choose enable disable 33 SMS Reply for Arm Disarm When the user arm or disarm the system other users may not know it Enable this function the panel will send SMS notification to all SMS numbers so that users could know the status of the system in time SMS content Out arm System armed disarm System disarmed Method enter settings menu and then you see operate password Press 6 to choose arm disarm SMS and choose enable or disable Operation figures 32 ce Fig 3 press 6 to choose arm Fig 4 choose enable dis
10. apter 6 Technical Parameters for system default settings Method enter defense zone setting menu press 4 or 6 to choose the zone number and then press 2 or 8 to enter zone place menu Press ENTER will shift the places Operation figures 12 Fig 1 enter defense zone setting l o i l 1 Place Fire l l o l Place GAS Fig 4 this example After setting it is 01 zone gas alarm Before setting the alarm SMS for zone 1 is 01zone fire alarm The format of alarm SMS 01 10 zone place alarm For example you set 6 the place of zone 4 as window The alarm SMS you receive is 04 zone window alarm 7 Defense Zone Mode Setting There are different defense zone modes out arm home arm alarm under disarm mode For example you need gas detectors working all the time please set ARM HOME and DISARM as enabled Method enter defense zone setting menu press 2 or 8 to choose HOME 13 arm status enable or disable press ENTER to confirm Setting methods for OUT arm and DISARM are the same Operation figures miei i Fig 2 choose mode HOME Disable HOME Enable Fig 4 this example Before setting zone does not alarm in home arm status l After setting it will alarm when triggered in home arm status 8 Siren Setting for Alarm The sir
11. c parts lt Do not place the system in excessively cold locations Otherwise condensation many occur and damage the circuit board of the alarm system lt Itis recommended that you check and test the alarm system periodically Check the main unit every three months 1 Whether it can arm disarm normally 2 Whether it can dial the number for alarm normally 3 Whether it can receive wireless detectors signal normally 4 Whether the back up battery can work normally Check the wireless detectors once a month 1 Trigger wireless detectors to see if system can alarm normally 2 Check all detectors batteries to see if it s in low voltage 3 Check whether wireless detectors can send signal to the main unit normally Check the SIM card 1 Check the use of SIM card such as network signal balance etc 4 2 Make sure the PIN code verification of the SIM card is closed 3 Please keep the password and SIM card number safe in case that other people remote control the system illegally lt Since the alarm system is continuously in operation or standby mode the supply adaptor of the control panel shall be connected to a safe and reliable socket lt Do not place the system near your bedroom or office table because the siren will make high loudness sound in the case of alarm which may adversely affect your rest or work lt Ifthe alarm system will not be used for a long time please disconnect the system from the po
12. en can be set on or off when there s alarm from each defense zone Method enter defense zone setting press 2 or 8 to choose siren enable or disable and then press ENTER to confirm Operation figures Fig 3 press ENTER to confirm Siren Enable Siren Disable Fig 4 this example Before setting the siren is on when zone alarms After setting siren will not sound when zone 1 alarms 9 Alarm Delay Setting Alarm delay the main panel will make alarm call and the siren will ring after the preset delay time Method enter defense zone setting press 2 or 8 to choose delay enable or disable and then press ENTER to confirm Operation figures BDIJE PAADIREIS Fig 3 press ENTER to confirm Delay Enable Fig 4 this example Before setting the panel makes alarm and the siren rings immediately when zone After setting alarm will be after the preset time set the delay time under system setting 1 is triggered mm sei i 15 10 Alarm Number Setting This system can store 6 alarm phone numbers When alarming it will make alarm call to these numbers in order for three times automatically until someone gets through the call Method enter phone number setting menu press 4 or 6 to choose serial number and then press ENTER Input the number you want to set then press ENTER to save Op
13. er This device supports maximum 8 remote controllers Extra remote controllers have to be coded to the host in order to perform normally Their code cannot be empty or the same with the saved code in the host Method enter remote controller setting menu press 4 or 6 to choose remote controller serial number press 8 to find coding and then press ENTER to confirm Trigger the remote controller you want to add the panel will make two beeps after receiving it And then press ENTER to confirm If the remote controller has been saved before after triggering it the main unit will make four beeps and LCD screen display Error Repeated code Operation figures Fig 2 choose remote control serial number and coding menu 077015192 0101010101010100 Normal code Trigger remote Fig 4B the host has the same code with remote controller code Error Repeated code 3 Delete Remote Controller If the remote controller is lost or damaged it should be deleted After deletion it cannot control the main panel Method enter remote controller setting menu press 4 or 6 to choose the 9 remote controller you want to delete Press 8 to find delete and then press ENTER Operation figures Fig 2 choose the controller you want to delete Fig 3 press ENTER to confirm 4 Coding of Defense Zone This alarm system has 10 wireless defense zones each of which supports up
14. eration figures Fig 1 enter phone number setting No number 123456789 Input phone number Fig 4 press ENTER to save Fig 5 the 1st number is set successfully o 123456789 11 Delete Alarm Number Method enter phone number setting press 4 or 6 to choose serial number then press 8 to choose delete and then press ENTER to confirm Operation figures 16 Fig 3 choose delete lt lt Phone 1 123456789 i l Back Enter a ee ee ee 5 a ey ee ee l 12 SMS Number Setting Fig 2 choose the number you want to delete a Phone 1 gt 123456789 Delete Back A Enter Fig 4 the 1st number is deleted lt Phone 1 gt Delete completed This system can store 3 SMS receiving phone numbers When alarming it will send SMS to these numbers Method enter SMS number setting press 4 or 6 to choose serial number and then press ENTER Input the number you want to set then press ENTER to save Operation figures lt Dx gt l SMS 1 gt Delete A BEB ENS Fig 2 choose serial number and press ENTER bss a ee 13812345678 Input phone number 13 Delete SMS Number Method enter SMS number setting press 4 or 6 to choose serial number then press 8 to choose delete and then press ENTER to confirm Operat
15. ill make alarm Use main panel keypad to press ARM You will hear 60 beeps per each 35 second and then the screen will display system armed Remote controller operation press arm button 8 on the remote controller Main panel operation press ARM The system will enter arm status after the 2 Home A Home arm Means pare ormo ueiense zonos aron arm status When there s someone at home it is recommended for safety purpose to enable some of the detectors such as sensors for door window balcony etc and disable the others such as sensors for the hall or some places easy to be triggered by person at home Use main panel keypad to press STAY The screen will display system armed Remote controller operation press home arm button r on the remote controller Main panel operation press STAY 3 Disarm The purpose of disarming the system is to let it not in alert status One way is normal disarming after operation of arming and the other is to stop the main unit alarming After the operation of disarm all the defense zones except 24 hour zone shall not work 36 Use main panel keypad to input user password The screen will display system disarmed Remote controller operation press disarm button E on the remote controller Main panel operation password ENTER 4 Answer Alar When the main unit sounds alarm 1t will dial the preset numbers If no one answers the call the system
16. ion figures Fig 2 choose the number you want to delete 13812345678 Delete 18 14 Network Center Setting This system does not have this function at present Please kindly contact us if needed 15 Voice Recording This system can make 10 second voice record When alarming it will make call and play this record Method enter record setting and start by choosing start recording It will stop automatically 10 seconds later Operation figures Fig 2 start recording Fig 3 record for 10 seconds Start recording 16 Record Play Enter record setting and then press 6 to choose play The panel will start playing the voice message you recorded You can re record if you re not satisfied with it Operation figures 19 Fig 1 enter record setting Fig 2 you ll see this menu l l l l Start recording l l l Fig 4 press ENTER to play the record 17 System Date Setting The date format is year month day Year setting is from 00 99 Method enter Time menu and then choose Date Input the exact date you want to set and press ENTER to confirm Operation figures Fig 2 choose date setting menu 11 12 12 20 010740107010 Please enter 18 System Time Setting Time in this alarm system is 24 hour system Enter Time menu you will see Date menu then press 6 to choose Time Input the exact time you want t
17. ireless siren setting and then enter transmission setting The panel will send a wireless signal to the siren Operation figures 23 Fig3 Press 6 to choose Wireless siren Transmission Fig 4 After pressing ENTER key the main unit will transmit a wireless signal to control the wireless siren 23 Wireless Siren Encryption The signal used to code with the wireless siren is sent from the internal transmitter of the main panel The signal codes of this model from our company are the same If you and your neighbor both are using this model the alarm signal from your neighbor may cause your siren sound So it is recommended to encrypt the wireless siren to avoid the interference Method enter wireless control menu and then control menu Press 6 to choose wireless siren then press 8 to choose encryption Input 4 24 numbers randomly and then save it Operation figures Enable Fig 3 press 6 to choose wireless siren 8907 Encryption Please input 24 Wireless Control for Home Appliances It does not have this function at present Please kindly contact us if needed 25 Change Operate Password Operate password is used for daily use disarm or remote control System 25 default is 1234 Method to change this password enter settings menu and then operate password Input the 4 digit password you want to set and save it Operation fig
18. o set and press ENTER to confirm Operation figures Fig 3 press 6 to choose time 11 12 12 Fig 4 input the time 00 00 Please enter 21 19 Timely Arm Setting After this setting the alarm system will start arm status at the preset time Method enter Time menu you will see Date menu then press 6 to choose Timely arm Input the exact time you want to set and press ENTER to confirm Operation figures Fig 2 you ll see date setting menu 11 12 12 DIERY 20 Timely Disarm Setting After this setting the alarm system will disarm automatically at the preset time Method enter Time menu you will see Date menu then press 6 to choose Timely disarm Input the exact time you want to set and press ENTER to confirm 22 Operation figures ei i Fig 1 enter time setting menu Fig 2 you ll see date setting menu I 11 12 12 1 I l Fig 4 input the time you want to set Disable 21 Wireless Control Setting This system does not have this function at present Please kindly contact us if needed 22 Wireless Siren Coding Wireless sirens have to be coded to the main panel in order to work normally Method set the wireless siren which you want to code in coding status Then enter wireless control menu in this panel you ll see control menu Press 6 to choose w
19. ress 3 again to monitor for another 30 seconds Press 4 two way intercom for 30 seconds You can t operate the main unit during this time 6 Emergency Help Sometimes there may be some accidents happening such as sudden illness of old people or children fire accident burglar intrusion Press SOS button on keypad or button on remote controller or wireless panic button the main unit will alarm and make call to the preset user numbers Remote controller operation press O button on the remote controller Main panel operation press SOS The SMS content for emergency help is 00 zone SOS alarm 7 System Dialing Function In disarm status you can use the main unit to make any call just like a land line telephone Dial telephone number on keypad press CALL button the main unit will make a beep and the LCD screen will display the number you are calling After the call press CALL button again the call will be hanged up and main unit will be in disarm status 8 Alarming Record Checking This alarm system can store 30 alarm records The last alarm is ranked as the first record And when the record number exceeds 30 the most previous record will be deleted automatically Checking method In disarm state input 00 ENTER the main unit enters the state of alarm record checking Press 4 or 6 to upturn or downturn and press Exit to exit checking 38 Fig 1 press 00 in disarm status
20. t ways panel keypad remote controller remote call Alarm call has the priority even when the number of the device is busy SMS alert for power failure or recovery Built in LI battery automatically recharge Chapter 2 Alarm Host Introduction 1 Yul om System disar ned gt i s oass2 _ 1 LCD screen Resolution 128x64 support English and Chinese display 2 Status LED POWER power and working status indicator flashing quickly once per second means the system is searching GSM network flashing once per 3 seconds means panel is under standby status SET it will be on when the system enters setting status SIGNAL signal indicator ALARM it will be on when the system is under alarm status 3 Touch keypad this keypad is Resistive Touch Panel which requires press with certain strength But please do not push it heavily ARM press it the system will enter OUT ARM status STAY press it the system will enter HOME ARM status CALL used to make call Enter the number you want to call and then press this button Press it during the phone call will hang up the call SOS emergency alarm ESC clear the input content or back to last operation ENTER confirm 4 Wired ports En SIREN Positive of siren red cable SIREN Negative of siren black cable T_VCC Invalid port does not have any function Invalid port DATA Invalid port Tnvalid port 6 EO mi 8 Zone 1 Wired sensor T support both NO and N
21. ures Fig 2 enter operate password menu Fig 3 input the 4 digit password Fig 4 save it Please input 4545 26 Change Program Password Program password is used to setup the system System default is 888888 Method to change this password enter settings menu and then operate password press 6 to choose program password Input the 6 digit password you want to set and save it Operation figures 26 Fig 3 press 6 to choose program i Fig 4 input password and save it passwor 888888 27 Arm Delay Time Setting After this setting the system will enter out arm status after the preset time Delay time ranges from 01 99 seconds The system default time is 60 seconds Method enter settings menu then you ll see operate password Press 6 to choose delay arm Input the time you want to set and save it Operation figures 2 Fig 2 youll see Operate password menu Fig 3 press 6 to choose delay arm Fig 4 input time and save it Please input l 08 28 Alarm Delay Time Setting After this setting when there s an alarm the system will make call after the preset time Delay time ranges from 01 99 seconds The system default time is 60 seconds Method enter settings menu then you ll see operate password
22. wer supply Please do not disassemble repair or alter the products without permission or it may cause accidents and faults lt Do not drop this product on the ground or on hard objects as it may lead to massive impact to cause faults and damages lt Without approval and consent of relevant authorities please do not set 110 119 or the alarm phone number of police station for this main unit Please read the suggestions above carefully and follow the instructions herein If any of the equipment does not work properly please send it to the dealer or authorized service point for repair We will try our best to solve the problem for you as soon as possible 42 The following sensors are optional Yee Y Wireless Outdoor Siren with flash Signal Repeater Wireless keypad 2 5 amp e e D Glass Sensor Panic Button Remote Controller ALA N S9 P p Wireless Smoke Gas Detector Wireless Pet Detector Immune PIR Detector Optional sensors detectors are packed separately You can choose according to your specific requirements Typical house configuration Pe External Sirens Door window F Z Garage N E f Pa j I j EEFI P Z p We OUP dP SEEE M Sa Smoke P PIR Movement Detector l Detectors
Download Pdf Manuals
Related Search