DUALSIMs 3G WIRELESS ROUTER / DTU MODEM VIN
Contents
1. Client End IP Address Remote Subnet 0 0 Remote Subnet Mask Local IP Adress Fig2 23 L2TP Configure Enable L2TP Enable the L2TP if this is selected Mode It supports both L2TP client and server mode Server IP Address Input the IP address of L2TP server here if VIN S1901 3G is configured as the client Client Start End IP Address The IP address which the VIN S1901 3G will distribute to the L2TP client this would only take affection if the VIN S1901 3G configured as the mode of L2TP server Local IP Address When the VIN S1901 3G configured as the L2TP server this will be the its own VPN interface IP address Username Username for L2TP authentication Password Password for L2TP authentication Remote Subnet The L2TP server side subnet IP address this and the next parameter supposed to be configured correctly if you want to communicate with the computer behind the L2TP server Remote Subnet Mask The L2TP server side subnet mask ap e VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 10 IPSec Tunnel Internet Protocol Security IPsec is a protocol suite for securing Internet Protocol IP communications by authenticating and encrypting each IP packet of a data stream IPsec also includes protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic keys to be used during the session IPsec2. poh ala eee Bridge IP 1192 168 0 1 Bndge Submask Bridge DHCP Server Parameters are the same as eth2 DHCP 4 Bridge Mode Fig2 3 Ethernet Configure Ethernet Mode The ETH1 and ETH2 can be set to 4 modes which are Normal PPPoE EWAN and Bridge In PPPoE Mode ETH2 is used as PPPoE WAN for uplink via external PPPoE modem In EWAN mode ETH2 is used as a Ethernet WAN for uplink In Bridge Mode ETH1 and ETH2 are bridged thus they are have the same address Note In Normal Mode ETH1 and ETH2 should be set in different sub network VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 4 Serial Configure Configure the serial port of VIN S1901 3G TS CN O py oe UUU A Ca Max Packet size 1 1024 Max Data Send Interval 1 2000 Max Data Wait Time 20 2000 Fig2 4 Serial Configure Baud Rate Configure the baud rate of serial port Data Bits Configure data bits Stop Bits Configure stop bits Parity Check Configure parity check Flow Control Configure flow control Max Packet Size This is the max serial data VIN S1901 3G could send during the Max Data Send Interval Max Data Send Interval This configuration decides how often the serial port data will be send once during the TCP and UDP transparent transport Max Data Wait Time This configuration decides how often the TCP and UDP transparent transport port will
3. transform to serial data during the TCP and UDP transparent transport 10 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 5 Timer Configure Configure the retry times of some functions PPP Wait Time 10 60 PPP failure retry bmes 0 1 60 0 for no reboot Heartbeat Cyde 10 600 with RSC Register ACK Wait Time 10 60 Auto Offline Wait Time 10 600 Cycle of Echo Sending 0 5 600 Failures of the Echo 1 5 Cycle of Online Keeper 0 1 1800 Fig2 5 System Timer configure PPP Wait Time The interval of redialing up when the dial up is failed PPP failure retry times Configure how many times the VIN S1901 3G will try to redialing up and after so many times redialing the VIN S1901 3G will be reboot Heartbeat Cycle with RSC The interval to send heartbeat packet to data center This is an old fashioned configure that few people use nowadays suggest not to use this configuration Register ACK Wait Time How long the VIN S1901 3G will wait to get the ACK from data center after it send out the heartbeat packet This is an old fashioned configure that few people use nowadays suggest not to use this configuration Auto Offline Wait Time How long the VIN S1901 3G will be time out and go offline when there re no packets sending This is an old fashioned configure that few people use nowadays suggest not to use this configuration Cycle of Echo Sending This parameter is about the PPP ne
4. be gotten automatically by network query Main Sim Card The first checked slot when boot SIMI1 s Access Point Name APN of SIMI SIMT s Service Number Dial up number of SIM1 SIMT s User Name Username of SIMI for dial up authentication SIM1 s User Password Username of SIM1 for dial up authentication Dial Mode There re two options of dial mode to choose when Always Online is chosen the 1901 3G will dial up directly when Data Trigger is chosen the dial up will be blocked until there s data come in from serial port Remote Wake up Manner The Dual SIM Router could be wake up by a phone call if the Ring is selected and if the Check Caller ID When Wake up is selected the VIN S1901 3G will verify the caller s phone number only the permitted caller could wake it up Note that the configurations could only be work and configured when the Data Trigger option is selected Offline When LAN is Idle When this is selected then if there is no data come in or go out of the ETH1 ETH2 interface in the specified time the VIN S1901 3G will go offline and until there is data come in from the LAN interface the router will dial up again VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 2 Application Parameter Configure Configure work mode here 1 Router Mode Aenima Serial Transmit w Chent Server COS CAI Application Mode Modem USB Interface 0 5
5. can be used to protect data flows between a pair of hosts e g computer users or servers between a pair of security gateways e g routers or firewalls or between a security gateway and a host Enable Sec Tunnel IFSec Tunnel Table SN Subnet GW Gateway ay Opp Subnet 5H 5N Hame L Subnet Mask Lateway O 3ubn t Mask FSE oK Add Da Fig2 24 IPSec Configure Enable IPSec Tunnel Enable the ipsec tunnel if this is selected Add Add a IPSec rule to VIN S1901 3G Del Del a IPSec rule in VIN S1901 3G Note The four tunnel modes are showed as Subnet Subnet SN SN Subnet Gateway SN GW Gateway Subnet GW SN Gateway Gateway GW GW In S1901 router there are some default settings 1 Using IKE 2 Exchange Mode Main Mode 3 Identity Type IP Address 4 Using Pre share Key 5 Encryption Algorithm 3DES 6 Authentication Algorithm MDS5 7 SA Life Time 28800 8 Enable PFS Td VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 11 VRRP Virtual Router Redundancy Protocol VRRP specifies an election protocol that dynamically assigns responsibility for a virtual router to one of the VRRP routers on a LAN The VRRP router controlling the IP address associated with a virtual router is called the Master and forwards packets sent to these IP addresses The election process provides dynamic fail over in the forwarding responsibility should the Master become unavailable This allo
6. 3 Modem Mode Fig2 2 Services Center Configuration Application Mode Set the application mode of VIN S1901 3G There are 3 modes to be selected 1 Router Default mode of VIN S1901 3G user who want their devices send data via Ethernet cable should use this mode 2 Serial Transmit Mode TCP Transmit In this mode the VIN S1901 3G will exchange data with peer from serial port using TCP protocol People who want their devices to send data using serial cable should consider using this mode UDP Transmit In this mode the VIN S1901 3G will exchange data with peer from serial port using UDP protocol People who want their devices to send data using serial cable should consider using this mode 3 Modem Mode VIN S1901 3G works as amodem and you could dial up to the Internet VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 3 Ethernet Configure Configure the Ethernet mode of VIN S1901 3G Ethemet Mode formal Node Y ETH1 Configuration Subnet Mask 266 255 0 0 PPPoE Device Name PPPoE Usemame a gt E 0 DD g g gI PPPOE Password password PPPoE Service Name PPPoE Echo Interval PPPoE Max Failures ETH1 Configuration Subnet Mask 265 265 255 0 2 PPPoE Mode VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL Ethernet Mode EWAN Mode WAN IP 10 0 0 Subnet Mask 10 0 0 ETH1 Configuration Device IP Subnet Mask Ethernet Mode Bndge Configuration
7. DUAL SIMs 3G WIRELESS ROUTER DTU MODEM VIN S1901 User Manual 3G WCDMA Ts TINFRODUCTIONS Sion no 1 1 1 TECHNOLOGY SPEC IFICA TIONS cccisccedtesasesvantescascessvcdestevacesecsbectecucuccesaveseceecasecssuseenececenuscusansuvcevantees 1 1 2 DEVICE APPEARANCE ccionn tosien eec constano eraan a ae E REEE EE N 2 A IME FRONT TANE oe ee N EO TET eer ee eee 2 EZ ACKO PAN BL EO Oe RC STIR EPC PT ae a 2 2 WEB PARAMETER CONFIGURATION sesesececcscococococococococococococococococococococeseceseseseseseseseseseseseseo 5 Del SYSTEM PARAMETERS c5scscccssesesdatensdncetaswcosacteeicdessassesecetonsecdasnoacetasvuseodescusseeassscueosnsasninessseuensseececnass 5 2 lel SERVICES CENTER CONFIGURATION a eens 5 ZA APPLICATION PARAMETER CONFIGURE ccfcatud vse orton E Sr DO 7 ZW ETHERNET CONFIGURE mses e e e e o e eo 8 i SERA SON O T racer A reset tte as ta aera eel ia ne a ae at 10 ZN TEI RG ONE IG URE one 11 E A A seen tt GI i he a ene a ae ee A 12 Dells ADVANCED PARAMETRO tas 13 ZO APO VERE TERNERA a 14 Zi La NETWORK CONFIGURE ois tisesiesviacesckcatsctncetscteuatcsucecawassesveceiuewcausacvecateceesaseedeeuccoueegusesceneseseswewcaweeees 15 PPN IN A ao 15 EL A A CONTI AAA A Ss es 17 TAO a id nd e er ees 18 LS O e ee LL 19 A O PP AR O 20 LO DDNS arcee AA A AS a 21 2e AAA AAN A A A A eouedtnoreaatanere 21 LS A aliens las 22 A sy NG E AAA IN A 23 22 O AP SEC TUNNE Eiei o US sas 24 A SPA A O ced E eee ca ta ce aed O A 25 EN A A O E E
8. EULE P add E of DMZ hos t or ne twork iptables configure Iptables rules time contigure the timely transmit mode Ipsec contigure IPSec tunnel boot goto bootloader mode pdp define PDP Context phy read amp write phy register she Into 1 nux she Fig3 1 Help Commands ee VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 3 2 Set commands Use set command to show all the commands you could use to configure the parameters in the VIN S1901 3G You could type the command in the front column to configure those relevant parameters show this help intormation set device UWS TLELI and Password app ML dhep ethernet rors timer cominto Coma E p d eb UE pptp ping application parameters Mobile Service Center parameters DHCP and DNS information ethernet parameters Reboot or Redial Settings timer parameters serial port parameters serial port application parameters debuging output parameters pptp parameters ping parameters advanced advanced parameters 12tp set 12tp parameters ntp set ntp parameters atovereth set at commands communication over ethernet ddns se ddns parameters vlan set vlan parameters YECH mE VEE GD parang ters Fig3 2 Set Commands 23d VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 3 3 Show commands Use show command to show all the commands you could use to show the parameters in the VIN S1901 3G You could type the command in t
9. S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 5 Device Status Some information such as signal strength network connection and so on will be displayed on the page of device status And this page will be refreshed every 10 seconds by default Signal strength SET_ECHO_OFF SHOW_MEINFO CHK_UIM SELECT RADIO BAND REPORT _NET_STAUS CHK WET NET_TYPE_LED CHK_OPS CHK OPS NUMERIC SET_CLIP CHK INIT_SERVICE Auto refresh 10 s Refresh Fig2 34 Device Status saje VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 3 CLI CONFIGURATIONS We strongly recommend user to configure the parameters with WEB console however VIN S1901 3G also supports CLI Command Line Interface configuration There are 2 methods into CLI a Telnet to VIN S1901 3G via Ethernet port b Always press Spacebar in Hyper Terminal when S1901 3G power on via serial port 3 1 Help commands Use command to show all the commands that the S1901 3G supports The front column is the command and the back column is the explanation help Information o lp Information of cc SYS tem par ame Lers system oY tem PAL AmE CEILS show 4 Stem parameters cont Lfuration tftp use tftp to update system online ad system contiguration parameters load Lo save save system parameters to FLASH print print out cfg file content nat configure NAT mapping table ifconfig configure secondary Ip route 0 F i Pure amp tat L route dmz conf 1 P
10. able Output Chains Protocol pea Dstination asi TCP wv srcAddress Mask DetAddress Mazk or Wad Dal e A praTETETETETETEEeE EEE A A A o A DD Fig2 28 IP Table Out Configure Add Add a new chain out Del Del the chosen chain out Ta VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 3 3 Iptable Script User can add some extra scripts to implement customized firewall Enable Iptable Script 28 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 4 System Manage 2 4 1 Firmware The firmware including kernel and romfs could be upgraded by http protocol here Fig2 30 Firmware Upgrde 2 4 2 System Tools Save Parameter to Flash Load Default Parameter Upload Parameter Download Parameter Update Software Download Software Update Kernel Download Kernel Reset System Goto Bootloader Mode Fig2 31 System Tools Save Parameter to Flash After you configure your parameters you could save them at here by select this and click the SET button The parameters will take the affection after reboot Load Default Parameter Load the default parameters Upload Parameter Load the parameters from a file on your PC to VIN S1901 3G You should run a tftp server software on your PC and put the parameter file in the same directory as tftp server software after that you should fill the Tftp Server IP with the PC s IP address and fill the F
11. es adding if the option of Ifconfig is enabled ___ Subnet Mask 255 255 255 0 Alias IF Fig2 15 Ifconfig Configure VIN S1901 3G can be accessed through the additional IP address Add Add a additional alias and IP address Del Delete the chosen additional alias and IP address Note The field of Ethernet Alias must be formatted as ethO xxx 417 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 3 Static Route Static route created manually by users is a very quick and effective way to route data from one subnet to different subnet Users can add or delete static route rules on VIN S1901 3G after enable the option of Enable Static Route on the page of Static Route Enable Static Route Interface eth0 eth1 eth_br F Note Route will mot work if the rule is not legal Static Route Table Del Num Destination Address Subnet Mask Dst ddresz Subnet Mask Gateway Interface m 0 Add Del Fig2 16 Static Route Configure Add Add anew static route rule Del Delete the chosen static route rule 18 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 4 Auto Ping Auto ping is a unusual way to check the connection between VIN S1901 3G and peer Users can enable this function and set some parameters VIN S1901 3G will reboot automatically if the failures of ping are more than settings Packets Every Auto Ping 0 50 Notice If 0 will ping a
12. finitions of LED Status AS TIA Alwayson Init Init failed PPP dialing PPP online PPP offline lash 1 time perFlash 2 time per 3s Flash 3 time per 3s oe off DS Register 2G Register 3G Signal fine Signal Normal Signal week Flash 1 time per 3s Flash 2 time sper 3s VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 WEB PARAMETER CONFIGURATION FET TN ES Ca REL Y EF conca dor iO monn Guero Cometh ray Tear EE m aE ai a F BG ia 2 1 System Parameters 2 1 1 Services Center Configuration Network and PPP dial mode can be set in this page VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL CDMA HDR HYBRID If GSM DCS systems W Extended GSM 900 iY Primary GSM 900 i GSM PCS W WCDMA IMT 2000 If WCDMA PES 1900 M WCDMA 850 SIM1 s Access Point Name PL NILAM SIM1 s Service Number pega SIM1 s User Password username Always Online Data Trigger Serial Data Remote Wake up Manner F Ring F Check Caller ID When Wake up Offline When LAN is Idle Fig2 1 Services Center Configuration Register Network Type The device within WCDMA module can be set as Auto GSM and WCDMA mode The device within EVDO module can be set as CDMA HDR HYBRID HDR and CDMA Radio Band Set The device within WCDMA module can be set to search the specified bands APN Appointed Mode User can set APN manually if it can t
13. gotiation it configures how often the VIN S1901 3G will send the echo packet out Failures of the Echo This parameter is about the PPP negotiation if the failures of echo up to this count then the VIN S1901 3G will do the renegotiation Cycle of Online Keeper This is used for sending out the online keeper packet so that the VIN S1901 3G could keep the wireless channel you could use the Auto Ping function instead oa le VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 6 Time Up Down Configure the VIN S1901 3G s working time Note 1 NTP should work Enable Time Up Down P 2 Data and Ring Wakeup will be disabled Time Up Down Table 08 00 00 20 00 00 UpTime DownTime a Add Sa Fig2 6 Time up down Configure Enable Time Up Down If selected the VIN S1901 3G will go online and offline at the specified time Add Click this to add a line Del Select the Del check box and Click this button could delete a line Note 1 NTP should work too and the time must be gotten successfully 2 Data and Ring Wakeup will be disabled if Time up down 1s enabled 12 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 7 Advanced Parameter Configure the advanced parameters including web server port PPP negotiation debug information etc Web Manage System Port PPP Authentication Mode Chap first then pap Control Host IP Address 0 0 0 0 Wake Up Phone Number zm
14. he front column to show those relevant parameters DTU show show show show show show 5 i IOW show a i OW show show show show show show show show show show cominto comapp ethernet msc app timer debug userinto advanced dhep ping rors l2tp ddns ntp vlan Vrrp all this help information serial port parameters serial port application parameters ethernet MSC parameters application parameters parameters timer parameters debugging information parameters user information advanced parameters dhep server parameters ping parameters restart or re d a SW l t Cc h l2tp parameters ddns parameters ntp parameters vlan parameters VIrp parameters all configuration information Fig3 3 Show Commands ee yee
15. he output of debug information form serial port Debug Output Level This parameter controls the mass of debug information The less this parameter is the more serial port will output ae VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 1 8 AT over Ethernet When PPP is up user can send AT command via Ethernet port to get some more information such as signal strength registered network type etc Enable AT over Ethernet To sender To specified addr AT Commands Data Format Private Protocol Normal Fig2 8 AT over Ethernet 14 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 Network Configure 2 2 1 NAT In computer networking network address translation NAT is the process of modifying network address information in datagram packet headers while in transit across a traffic routing device for the purpose of remapping a given address space into another Most often today NAT is used in conjunction with network masquerading or IP masquerading which is a technique that hides an entire address space usually consisting of private network addresses behind a single IP address in another often public address space This mechanism is implemented in a routing device that uses stateful translation tables to map the hidden addresses into a single address and then rewrites the outgomg IP packets on exit so that they appear to originate from the router In the reverse communications path re
16. ile Name with the parameter file s name click SET button to start upload the parameter Download Parameter Load the parameters from VIN S1901 3G to PC also need to fill the Tftp Server IP and File Name Reference to the Upload Parameter instruction upside Upload Software Load the software image from PC to VIN S1901 3G Reference to the Upload Parameter instruction upside Download Software Load the software image from VIN S1901 3G to PC Reference to the Upload Parameter instruction upside Upload Kernel Load the kernel image from PC to VIN S1901 3G Reference to the Upload Parameter 29 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL instruction upside Download Kernel Load the kernel image from VIN S1901 3G to PC Reference to the Upload Parameter instruction upside Reset System Reboot VIN S1901 3G Goto Bootloader Mode Let VIN S1901 3G go to the bootloader mode Tftp Server IP Used to fill in the tftp server IP address File Name The file name you want to save as or load from 2 4 3 User Manage Fig2 32 User Manage User Name Username when login the VIN S1901 3G Default value is admin Password Password when login the VIN S1901 3G Default value is 12345 2 4 4 Version Device Name Fig2 33 Version Information Device Name Device name of 1901 3G Version Software version 30 VIN
17. ility accord YD1169 1 standard VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 1 2 Device Appearance MET coma E woo RUN Tosco Ss PWR Power Supply 5 30WDCIZA Fig1 1 Top Panel 1 2 1 Front panel Fig1 2 Front Panel VIN S1901 have 2 SIM card slots which backup each other Users can push left button to extract the SIM card 1 2 2 Back panel Fig1 3 Back Panel Reset The button of Reset can reboot the device or recover the parameters to default e VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL Power input DC 5V 30V adapter provides the power supply of VIN S1901 RS485 The default baud rate of RS485 is 115200bps Table1 1 Definitions of RS485 DPO RS232 The default parameters of serial port Baud rate 115200bps Data bits 8 Stop bits 1 Parity check none Flow control none Table1 2 Definitions of RS232 DB 9 Male OUTPUT SR Signal Grama AY Ts rts Request Tosa four De fm Ringindcator TT ourrut ETH1 ETH2 Standard 10 100BaseT Ethernet interface Auto Negotiation The default IP of ETH1 is 192 168 1 1 and also the default IP of ETH2 is 138 0 19 1 ANT Standard 50Q SMA female LED Indicators Fig1 4 LED Light oe VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL The router has 3 LED which are NET RUN and PWR They indicate current network type signal strength and the work status of the device Table1 3 De
18. k gateway will be distributed to device Get DNS from Operator Set the DNS of DHCP as the DNS gotten from PPP negotiation or manual DHCP Primary Secondary DNS The primary secondary manual DNS DHCP IP Lease Time day The device will request updating the IP while it works more than this time 20 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 6 DDNS DDNS Dynamic DNS allows you to create a hostname that points to the IP of S1901 3G assigned by wireless network providing an easy to remember URL for quick access URL is static even though its IP is sometimes dynamic User can access VIN S1901 3G by URL instead of IP address jEnable DONS client Fig2 21 DDNS Configure User can access VIN S1901 3G by mytest dyndns org instead of its IP DDNS SERVER A server host which runs DDNS protocol Hostname Username Password These parameters are applied to DDNS server provider 2 2 7 NTP NTP is a protocol designed to synchronize the clocks of computers over a network INTP server IP T ime zone Fig2 20 NTP Configure VIN S1901 3G will automatically synchronize its clock to NTP server if NTP is enabled NTP Server IP Input a NTP server IP Time zone Local time zone Z ls VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 8 PPTP The Point to Point Tunneling Protocol PPTP is a method for imple
19. lways uto Ping Packets Size 1 1024B uto Ping Interval 1 6005 uto Ping Dest IP uto Ping Max Fallures 5 100 Fig2 17 Auto Ping Configure Packets Every Auto Ping The number of packets will be sent when send a ping request Auto Ping Packets Size The size of one packet Auto Ping Interval The interval of ping request VIN S1901 3G will always send ping request if it s set 0 Use Peer IP Addr As Auto Ping Dest IP Set the destination host of ping as peer IP gotten from PPP negotiation or manual Auto Ping Dest IP Set the manual destination host of ping Auto Ping Max Failures VIN S1901 3G will reboot automatically if the failures of ping are more than this value 19 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 5 DHCP The DHCP Dynamic Host Configuration Protocol is a computer networking protocol used by host DHCP servers which dynamically distributes the IP address to the destination device DHCP clients Enable DHCP ethO Server Enable DHCP eth1 Server DHCP start IP sipB i OOO OO ET DHCP Subnet Mask 255 255 0 0 DHCP Subnet Mask DHCP Gateway tew ay 192 168 1 DHCP Primary ONS CP Primary Or 122 168 1 1 a s sememssmssss sss seeeseama n DHCP IP Lease Time day Fig2 18 DHCP Configure DHCP Start End IP The DHCP server will distribute IP to the destination device from Start IP to End IP DHCP Subnet Mask Gateway This subnet mas
20. menting virtual private networks PPTP does not provide confidentiality or encryption It relies on the protocol being tunneled to provide privacy Fig2 22 PPTP Configure Enable PPTP Enable the PPTP if this is selected PPTP Server IP This is the PPTP server which the VIN S1901 3G will connect to The VIN S1901 3G could only supportthe PPTP client mode PPTP Client User Name Username for the PPTP authentication PPTP Client Password Password for the PPTP authentication Enable MPPE Enable MPPE encryption Remote Subnet The IP address of subnet on the server side this and the next parameter supposed to be configured correctly if you want to communicate with the computer behind the PPTP server Remote Subnet Mask The subnet mask on the server side Enable Appoint IP If this is selected the VIN S1901 3G will distribute the IP address to both client and server sides of the PPTP The PPTP server should configure this option also PPTP Local IP Client side IP of the PPTP PPTP Remote IP Server side IP of the PPTP 22 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 9 L2TP Layer 2 Tunneling Protocol L2TP is a tunneling protocol used to support virtual private networks VPN It does not provide any encryption or confidentiality by itself it relies on an encryption protocol that it passes within the tunnel to provide privacy pe id cee Client Start IP Address
21. nn O hate teh Saale catch a ates Caren eal Ate ci 25 ede SECURITY CONFIG URE aoisean a a i a ES 26 SS MS NA A IA 26 ASA A A A A 27 AS IS A A COT EO Ee RT 28 2 4 SYS TEM MANAGE AAA II ONO EE EEE NEKO EEEE E EEEREN 29 Zake cle TIRING AU o lee el Ode 29 DAD SYSTEM LOOSE A A Rs ee A er as 29 EN AA NO e e eae ae ee eee 30 DAS NER TON A AS RA A Ai E 30 2 5 DEVICE STATUS cenecananccccenaueteteeeesecs 31 3 CECCONFIGURATIONS sisecsccsdscssswsnusesscescscesnscuecaccncsassucnuvesseccstecaewensausenecsepbecnssatseaessonscmesceobeenesenes 32 SE HEP COMMANDS aeta to 32 SL SET COMMANDS acrescida a a a aaa O aa aaa aa eaaa 33 3235 SHOW COMMANDS eoor a A a a a aN 34 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 1 INTRODUCTIONS 1 1 Technology specifications Network HSPA EVDO TD SCDMA amp EDGE GPRS CDMA 1X System 1 2 3 Interface 1 2 3 4 Processor ARM FLASH 4M SDRAM 16M Anterna 50Q SMA negative SIM card X 2 Level 3V Serial port X 2 Standard RS232 RS485 Baud rate 300 600 1200 2400 4800 9600 19200 38400 57600 115200bps Physical interface DB9 male RS232 Plug PIN RS485 Ethernet port X 2 Speed 10 100BaseT Physical interface RJ45 Power supply 1 2 Others 1 2 3 4 Voltage DC 5V 30V Power 3W Size 148mmx105mmx28mm Operation temperature 10 C 50 C limit temperature 30 C 70 C Relative humidity 10 90 non condensing Electromagnetic compatib
22. o Enable PPP Parameter Configured Output Debug Info to Serial Port Debug Output Level 0 9 0 Output All Fig2 8 Advanced Parameter Configure Web Manage System Port The port of WEB server on VIN S1901 3G is used for WEB login PPP Authentication Mode There are 3 modes used on the process of PPP negotiation which are Chap first then pap Chap only and Pap only Reset Timer User can enable the reboot timer and set the interval of reboot Control Host IP Address The host IP address which can control the PPP connection online or offline Wake Up Phone Number 1 This phone numbers can only wakeup the VIN S1901 3G online if the VIN S1901 3G is configured data trigger and allows ring wakeup Enable PPP Parameter Configured The PPP negotiation can be set here if select this option after click the button of SET Enable PPP Parameter Configured Configure Fig2 9 PPP Negotiation Enabled When click the link of Configure a new page will show Enable PPP IP Configure IP Address after Dial up nable Negotiate MRU Enable Negotiate Synilap Enable Negotiate Magic Number Enable Negotiate Protocol Field Compress Enable Negotiate Address Control Field Compress Enable Negotiate BSD Field Compress Fig2 10 PPP Negotiation Configure User can configure other parameters of PPP negotiation such as MRU compress etc Output Debug Info to Serial Port This parameter can enable or disable t
23. sponses are mapped back to the originating IP address using the rules stored in the translation tables Fig2 11 NAT TCP tl Port DstAddress Port w Aad ter Fig2 12 NAT Configure 15 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL When access the port 81 of ppp0 VIN S1901 3G IP assigned by wireless network the host 192 168 1 2 80 will be accessed Similarly port 82 of ppp0 maps 192 168 1 3 80 Add Add a new mapping rule Del Delete the chosen mapping rule DMZ is a firewall configuration for securing local area networks LANs In a DMZ configuration most computers on the LAN run behind a firewall connected to a public network like the Internet One or more computers also run outside the firewall in the DMZ Those computers on the outside intercept traffic and broker requests for the rest of the LAN adding an extra layer of protection for computers behind the firewall me Y mill A e oe 193 165 1 1 Fig2 13 DMZ Enable DMZ DMZ Host Address 192 168 1 2 Fig2 14 DMZ Configure When external host access ppp0 the DMZ host 192 168 1 2 will be accessed actually Enable DMZ Enable DMZ function or not DMZ Host Address The IP address of DMZ host must be in the same LAN with Ethernet port of VIN S1901 3G 16 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 2 2 Ifconfig The Ethernet port of VIN S1901 3G wireless VIN S1901 3G supports additional IP address
24. ws any of the virtual router IP addresses on the LAN to be used as the default first hop router by end hosts The advantage gained from using VRRP is a higher availability default path without requiring configuration of dynamic routing or router discovery protocols on every end host Route IP 169001 O 0 0 1 IvRRP Hello Internal VRRP Broadcast IP 224 0 0 18 Fig2 25 VRRP Configure 2 2 12 Vian The protocol of Virtual Local Area Network Vlan is 802 11Q vian ee eth1 gt ETH1 168 0 0 1 Fig2 26 Vlan Configure 25 VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 3 Security Configure VIN S1901 3G provides firewall through iptable scripts User can set the parameters of iptable in and out to implement pop firewall And iptable scripts will help user to create some more customed advanced firewall 2 3 1 Iptable In All IP packets in will be blocked except the chains added into this table if the option of input chains is enabled Enable Iptable Input Chains Tam sm om sen ma m ICP w SrcoAkddress Mask DstAddress Mask OR Add Bel Fig2 27 IP Table In Configure Add Add a new chain in Del Del the chosen chain in LAG VIN S1901 Dual SIMs 3G Wireless Router USER S MAUAL 2 3 2 Iptable Out All IP packets out will be blocked except the chains added into this table if the option of output chains is enabled Enable Iptable Output Chains Ipt
Download Pdf Manuals
Related Search