SERVIS Drawer 17inch [FD-1100AT] User`s Manual
Contents
1. Num Caps Scroll Lock Lock Lock O OO O Hot key Button Reset Button Hot key Button Outputs the Ctrl Alt Shift key Make Break code This will also be the Hot key mode if a 4 port KVM switch is connected Reset Button Resets the keyboard and pointing device Also resets a 4 port KVM switch if one is connected However it will not reset any secondary slave 4 port KVM switches KVM Switch Reset is only valid with the following series FS 1004 AN ene 1008 and 1016 6 10 Using a 4 port KVM Switch The Console Drawer display parameters are the same regardless of video source so the image position may shift around due to the different video settings in various servers Generally the resolution and refresh rate vertical frequency are the same for many servers therefore one set of parameters which support those server CRT controllers are stored in the Console Drawer screen If you change the Console Drawer display parameters to match the video output of one server the video from all or some of the other servers may be negatively effected To correct for multiple display issues try the following 1 Change the refresh rate of servers that do not display correctly to a different value 2 Select the best compromise screen display and save the values As multiple refresh rates for each resolution can usually be set you can use various combinations for each of the servers to achieve optimum results2. monitor less than 1280 x 1024 interpolation of the low res output not by physical magnification So letters may be blurred and the thickness of thin lines might be uneven by this scaling function This is not a display failure and the device can be used normally Set resolution as 1280 x 1024 in property of monitor in server for displaying in best mode Poor screen quality Connection cable is defective Confirm the connector connection Faded images blurred Replace with a different cable If this characters etc solves the problem replace with a new cable Adjustment of monitor does not Push Auto switch give suitable results Window shifts or does not Wrong resolution Adjust the resolution or change the display when switching monitor settings 10 5 Others Keyboard and mouse The key repeat is abnormal Change the speed setting for the do not operate or key repeat on the server operate strangely A non specified cable is used Use a specified cable Operation stops aftera Connection has been Check the connections and then period of normal disrupted restart operation A problem has occurred at the Correct the problem at the server Server The auto scan switch The switch cycle has not been Use the cursor keys 1 and to adjust cycle is abnormal adjusted it The default value is 10 seconds 32 memo Console Drawer User s Manual Published October 2005 Published by FUJITSU COM
3. Authorized Company THE WARRANTY SET FORTH IN THIS SECTION IS IN LIEU OF AND EXCLUDES AND EACH PARTY HEREBY WAIVES ANY OTHER REPRESENTATIONS GUARANTEES AND WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL FUJITSU BE LIABLE TO PURCHASER FOR LOSS OF PROFITS LOSS OF USE COST OF SUBSTITUTE GOODS OR CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY KIND BASED UPON A CLAIM FOR BREACH OF WARRANTY OR OTHERWISE FUJITSU S WARRANTIES SHALL NOT BE ENLARGED DIMINISHED OR AFFECTED BY AND NO OBLIGATION OR LIABILITY SHALL ARISE OR GROW OUT OF SELLER S RENDERING OF TECHNICAL ADVICE OR SERVICE IN CONNECTION WITH BUYER S ORDER OR THE PRODUCTS FURNISHED HEREUNDER 3 Installation N SUN Please note the safety information in Important Notices 3 1 Installing the Console Drawer procedure for tapped guide rails Observe the specified environmental conditions when using the CAUTION Console Drawer See Technical Specifications for more information N Avoid dust humidity and extreme temperatures Installation may require two or more people in some situations Be careful not to pinch your fingers or hands between the guide rails and the Console Drawer 3 2 Installation Procedure Insert the rear spacer studs of the guide rails into the holes in the rear rack pillars Extend the guide rails to reach the inside of the
4. bumping and shaking Do not unpack the Console Drawer until the move has been completed 2 3 Disposal This device consists of metal plastic electronic parts and so on Some N CAUTION electronic components such as LCD monitor include lead When it is disposed of follow exactly the relevant government regulations instructions and so on 2 4 Safety Precautions and Limited Warranty Information Fujitsu s Products are not designed for use in medical or life support appliances devices or systems where malfunction of a Product can reasonably be expected to result in a personal injury The Product is designed developed and manufactured as contemplated for general use including general office use personal use household use and ordinary industrial use but is not for use for high risks or dangers that could reasonably be expected to result in personal injury or other loss including without limitation nuclear application aircraft flight control air traffic control mass transport control medical life support system or missile launch control in weapon system High Safety Required Use You should not use this Product without securing sufficient safety required for such High Safety Required Use Purchaser and its customers using or selling Products for use in such applications do so at their own risk and agree to fully indemnify Fujitsu for any damages resulting in such improper use or sale Fujitsu Component Limited or i
5. front rack pillar Fasten each guide rail with four screws one into each of the top and bottom holes of both the front and rear spacers Install the left and right guide rails at the same height 2 Extend the guide rails to reach the inside of the front rack pillar Fasten each guide rail in place with two screws one into each of the top and bottom holes of the front spacer Attach the guide rails inside the front rear rack pillar so that the guides face inwards 3 Install the left and right guide rails at the same height Attach the guide rails so that they face inward and are open forward ready to accept the Console Drawer Attach the guide rails inside the front rear rack pillar oee the Installing the Guide Rails diagram Point Rear Spacer Guide Rail Front Spacer Rear Spacer Win Ue ha Vu Ru Gu Vu Wu Be Ue Ru Ru Wy Ru Oy Ve We Ru Ue Ru Ru Ue Ru Ru Vu Ru Ru Le Ru Ru le Ru Ru Vu Ru be Le Ru Bale Ru Ru Vu Ru Ge UA Rear Spacer Guide Rail Front Spacer Rear Rack Pillar Front Rack Pillar Installing the Guide Rails 4 Slide the Console Drawer into the front end of the guide rails Point Be careful that the latch lever does not come loose If the latch lever comes loose the Console Drawer may slip If the Console Drawer does not slide easily into the guide rail or is too heavy get one or more other people to help you lift and insert it 5 Push the Console Drawer in
6. until it stops then fasten with two screws one on each side of the front of the Console Drawer KI Guide Rail Guide Rail Console Drawer Screws Latch Lever Installing the Console Drawer 3 3 Installing the 4 port KVM Switch If you don t have a 4 port KVM Switch please skip this section and go to the section for Connecting and Removing the Cables Refer to Connecting to Ports for the connection in general In details refer to the original manual for the 4 port KVM switch To avoid electric shocks and or short circuits make sure that the power cable of this device is not plugged into the power outlets Since this device may cause injury if it falls or tips over be sure to work on a stable surface such as on desk table and so on This device contains components that store and release high voltage electric charges Make sure to work only after checking that it has been electrically discharged Be careful not to cut yourself by sharp metal edges To avoid damage be careful of any objects falling including metal objects water and liquids into this device Do not touch unnecessary place To install 4 port KVM switch refer to the manual of 4port KVM switch Prepare screwdrivers large and small in advance 8 It is strongly recommended to install the 4 port KVM after removal of Point the Console Drawer from the rack When removing Console Drawer see Installing the Console Drawer It requires th
7. when the menu is not displayed It is possible to perform automatic adjustment position and focus by pressing the AUTO EXIT button when the menu is not displayed 16 6 3 Basic Adjustment Procedure The basic adjustment procedure is as follows Main Menu Main Menu Si sz OMo Pose Bo MENUJENTER on Button BRIGHTNESS mu POSITION ALITOJEXIT Button Display the menu Select an Item Cancel AUTO EXIT aa Adjustment Screen Button Sub menu Cancel Button MEHLIEHTER Button MENILI ENTER Adjust the value Button Adjust the value Button Save sub menu Main Menu POSITION ax ES GG A AUTOVEXIT Button Some main menu items do not have associated sub menus in which case the adjustment screen appears when the item is selected If the AUTO EXIT button is pressed at this phase the screen returns to the main menu and any adjustment to setting will not be saved The screen brightness setting BRIGHTNESS can be adjusted using the gt and lt q buttons without opening the main menu first In this case the setting is saved as it is being adjusted 17 6 4 Main Menu Items Symbol Function VL BRIGHTNESS Adjusts the screen brightness CONTRAST Adjusts the screen contrast COLOR Adjusts the screen color Fixed values or individual color tones red green blue can be set H POSITION _ Adjusts the display position horizontal V POSITION qw A
8. 0 cpi counts inch 3 Multi Interface PS 2 USB Sun I O and USB Supported by changing cable 2 e Standard FCC Class A VCCI Class A clUVus CE ICES 003 LS 9 Optional Accessories Sold separately 9 1 Optional Cables Items Product P N Descriptions AC Power Cable NC14004 B074 for 8 16 port KVM all US AC Cables Bo models AC Adaptor Cable AC Adaptor Cable Cable NC14004 B077 for 2 4 port KVM Cats Extender NC14000 B800 07 PC Cable Drawer Interface USB Cable Cables Sun I O Cable Note 1 Above P N for AC cable is US model AC cable are available for another countries Note 2 Contact your Fujitsu Components salespersons Note 3 All US drawer models include AC power cable US 2 port KVM ATL models includes AC adapter cable Note 4 Drawer I F cables Non standard 0 m and 3m cables are also available please contact sales office for information Note 5 NC14010 B452 US AC power cable included 2 0m PS 2 amp USB cables marked as are included SUN I O cable sold separately 9 2 Optional Guide rails tem Product PN NC14003 T591 Standard inside mounted guide rail Guide Rail NC14003 T592 Outside mounted guide rail NC14003 T593 oide mounted guide rail 20 10 Troubleshooting Check the following points if you encounter problems with the Console Drawer 10 1 No image displayed on monitor Symptom Predicted cause LED light for Power Indic
9. 3 FOS FOG F08 Fog F10 F11 Fle F13 Fla F15 E t 2 es E d J 2 Fior i2 ns ex lt 0 E02 Y Ps ad a ze Q a po B T Men D o p p col coa C03 C04 C05 C06 COT cos cog l C12 CapsLock aia dd 4d di aia PUTT EEE TT Er AM PPT ERE Fn ctrl Alt Gr ae Fig Japanese Keyboard Point Example of usage Fn 21 6 8 Pointing Device Operation Lightly touch or tap the touchpad surface to operate the pointing device Moving the pointer Lightly slide a finger over the touchpad surface in the direction you want the cursor to move Single click Lightly tap the touchpad surface once or press the left button once Double click Lightly tap the touchpad surface twice or press the left button twice in succession Touchpad Left Button Right Button CAUTION 1 The pointing device is designed to be operated with one finger and may not respond correctly if you try to operate it 1 while wearing gloves 2 with a pen ballpoint pen or pencil etc 3 with two or more fingers 4 while something is resting on the touchpad surface 2 Normal operation may become impossible if the touchpad surface is wet This can occur when the humidity is high or the operator s hands are damp or sweaty Thoroughly dry or wipe the touchpad surface before use 3 Do not operate with pointed metal objects such as pens as it may damage the pointing device 22 6 9 Hot key and Reset Buttons Hot key
10. 6 11 Stowing Console Drawer The Console Drawer should be stowed away in the rack when the monitor and keyboard are not in use Point Slide the Console Drawer in and out of the rack slowly 1 Push the monitor power button to turn off the power to the monitor 2 Hold the handle and slowly close the monitor Be sure that the LCD lock engages 3 Push the locking springs on both sides of the slide rail and slide the Console Drawer into the rack Be sure the latch lever engages CAUTION Be careful not to pinch your fingers in the guide rails slide rails or N the Console Drawer itself when stowing the Console Drawer If the latch lever does not lock the Console Drawer can unexpectly slide Out backlight or stow the Console Drawer in the rack when the monitor is not in use When the Console Drawer is closed the backlight will turn off automatically P j I To conserve electricity and maximize backlight life turn off the Guide Rail Slide Rail Console Drawer Latch Lever Cable Duct OW SZ Handle LCD Lock Latch Lever Slide Rail Lock Spring Stowing the Console Drawer f Cleaning the Console Drawer 25 Do not use cleansers that contain abrasives or organic solvents such as benzene or thinner or alcohol Do not apply water detergent or spray type cleaners directly onto the Console Drawer If liquids enter the interior of the Console Drawer it can cause malfunction
11. D 2005 Contents j N a AC RPM 1 Tob CONVERUONS S oisaiurioninieni nion e a aonb 1 FEFK LIS ae E A oT a EE ey eRe DUE 1 2 NOOR I NO UCC S uin evi queas Enim eU bonu E xA E e iix esp 2 UNE V IIP 3 2 2 Moving Console LAW CI seeren uds ind ead audiui iet tc tut d dea dude edle odeur efie dde 4 2 9 IDIISDOSBLuttastidutaatat ate cime Esa e MD DEDI EN E KD UU M Eme de aut 4 2 4 Safety Precautions and Limited Warranty Information eeeeeeeeeeeeeeseesse 4 SANA Cell LEON eaistaatage aan vu sabes Ei 6 3 1 Installing the Console Drawer procedure for tapped guide rails 6 9 Installauob roCedUlGssacsterstoresorstatstocstateba cot ba reat abo Senatu iod uad ei dese iode se iode dectedesd d doe debe 6 3 9 Installing the 4 port KVM SWIICD ico iiio bic bdeo bore tdea i Qvo vo ivo Ov abor s Du set Ou neve Uu o esed uoo eeu eoi noui 9 4 Connecting and Removing Cables 11 AT COMMECIMNG the Cables E EG 11 4 2 REMOVING Gables 2 52 10 00 a otto Nate i cede dee ed Res andeaonteede Oa vedo eee ann 11 9 Connecting to Multiple Servers with a 4 port KVM Switch installed in the back of the Console Drawer 12 6 OPErAatiOn ccccceceecseeceeceeeseeceeceeeeeeeeteteeseneteeteeeeeeteeeeees 13 6 1 Operating the Console Dra
12. MENT FAILED SEE USER S MANUAL UNSUPPORTED Use of non standard display Check the current resolution and MODE resolution or refresh rate refresh rate using the menu screen SEE USER S information Change the server MANUAL settings to the standard display resolution and refresh rate mode if necessary 10 4 Other Irregularities in Monitor Display Dancing pixel The FOCUS setting is not Adjust setting in FOCUS proper Vertical e on monitor Monitor setting is not proper Adjust setting in CLOCK and then adjust setting in FOCUS niai some noise in Video signal from server Decrease the value of black color black display mode produces the noise offset level for OSD function in BLACK LEVEL Window for display shifts Display positioning is not Adjust display position properly in displays over window adjusted properly POSITION after adjustment value in displays much small than CLOCK the window The setting value for resolution in Set the proper resolution in the server server is out of this product which can be supported by this capability product Monitor turn off AC cable is not inserted into the Confirm and connect the AC cable occasionally socket properly properly Uneven thickness of The setting in FOCUS and Adjust setting in CLOCK then adjust letters subject to the CLOCK is not proper the setting in FOCUS position displayed in Displayed in lower resolution Full screen display is made by digital
13. PONENT LIMITED Printed in Japan The contents of this manual may be modified for improvements without prior notice Fujitsu bears no responsibility for infringement of patent or other rights of third parties ascribable to the use of data in this manual Reprinting of this manual without permission is prohibited Manuals with missing or wrongly collated pages will be replaced free of charge C2 FUJITSU NC14010 L525 01 051005 This manual is made with recycled paper
14. Preliminary Ver 0 50 SERVIS Drawer 17inch FD 1100MT NC14010 B452 xx User s Manual L A cO FUJITSU FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CONTAIN MERCURY AND MUST DE RECYCLED OR DISPOSED Or ACCORDING TQ LOCAL STATE OR FEDERAL LAWS 49 LAMP S INSIDE THIS PRODUCT This device has been classified as a Class A product by VCCI Voluntary Control Council for Interference by Information Technology Equipment If you use this product in a domestic environment it may cause radio interference in which case the user may be held responsible for the cost of any required corrective action VCCI A All Rights Reserved Copyright FUJITSU LIMITE
15. ator is turned off Power Indicator glows orange Or display shows Message of POWER SAVING when pressing the MENU ENTER button Although the Power Indicator glows the Monitor does not display at all or the Monitor only displays one of the following messages OUT OF RANGE H kHz V kHZz SEE USER S MANUAL or NO SYNC SIGNAL SEE USER S MANUAL The AC cable is not connected to Connect the AC cable properly the electric outlet or to the switch device or not inserted into the socket properly The AC power is off Turn on the AC power POWER button was turned off Turn POWER button ON Power lamp green is out No image signal from server Input image signal from server Suspended state The server is in the stand by mode Press any key in keyboard or operate the touchpad which makes the server unlock the stand by mode The monitor cable is not connected Connect the monitor cable properly or not inserted into the socket properly The setting value for resolution Set the proper resolution and refresh and refresh rate in server is out of rate in the server which can be this product capability supported by this product The AC power for this product was Turn on the AC power for this turned on after the power for the product before or at the same time server was turned on when the power for server is turned on The monitor cable is not connected Connect the
16. avoid electric shocks and or short circuits Arrange the adequate area to have the plug quickly pulled out around the Console Drawer s power socket or the rack s power outlet Lay all the cables so that they will not be damaged Refer to the relevant sections in Installation when connecting and removing cables Do not connect or remove any cables during thunderstorms Do not allow foreign substances such as necklaces or paperclips or liquids inside the Console Drawer In an emergency such as damage to the housing parts or cables or liquid or a foreign object has fallen into the Console Drawer remove the power cable as soon as possible and contact your place of purchase or an authorized maintenance person e Do not disassemble or modify the Console Drawer for any purpose which may cause electric shocks or fire and so on Only licensed engineers may repair the Console Drawer Note that the corners of the open Console Drawer can be dangerous if bumped into Always be careful when the Console Drawer is open It is recommended that the Console Drawer be stowed away in the rack when it is not in use or when other nearby servers or peripheral equipments are being used Avoid using the keyboard when in poor health or for extended periods of time Always hold the connector portion and do not jerk the cables when removing them Avoid operating the Console Drawer with wet hands Do not plug or unplug connectors with wet han
17. djusts the display position vertical CLOCK Get rid of vertical striping noise FOCUS Get rid of horizontal noise and sharpens up blurred on screen lettering Switches the sRGB functions on off BLK BLACK LEVEL Sets black color offset level at any value GRADATION Changes the contrast curve to change half tone image expression TEXT MODE Sets the DOS screen resolution Be sure to set 720 x 400 when using English DOS LANGUAGE English Deutsch Italiano Francais Espanol INFORMATION Shows the currently set values for the screen resolution vertical frequency etc not all settings are shown RECALL Reinstates the factory default values e READJUSTING Recalls all the factory default values e GEOMETRY Recalls the screen resolution POSITION CLOCK and FOCUS default values e COLOR Recalls the BRIGHTNESS CONTRAST BLACK LEVEL and COLOR default values H HgOoHD S N m E m 2 ee 6 5 Resolutions and Refresh Rates Horizontal frequency Vertical frequency KHz Hz 640 x 400 VGA 400 LINE 31 5 60 VGA Standard 640 x 480 720 x 400 31 5 35 2 37 9 800 x 600 TR 48 1 48 4 1024 x 768 06 9 64 0 1280 x 1024 80 0 61 9 71 8 71 4 VESA 1152 x 900 Sun Composite 1280 x 1024 O N N A ialalsalialala a uo Oi a o o m oo o6 o 6 6 Caution LCD display Following cases are not considered as a failure mode and the device can be used normally During or soon a
18. dle and then grasp the handle and open the monitor by lifting it up 4 Turn on the power by pushing the POWER button Open the monitor completely Point Handle A _ Slide Rail PS Monitor LCD Monitor Power Button Hot key Button Reset Button Guide Rail Slide Rail Pointing Device LCD Lock L atch Lever Opening the LCD 6 2 Adjusting the Monitor The five buttons and one LED on the monitor are in order AUTO 1x MENU EXIT ENTER PA FN bow AUTO EXIT 4 vA MENU ENTER i i B Power Button Button Button Button Lamp 7 Button Power Lamp Power Button MENU ENTER Button This lights blue when the power to the monitor is on lights orange when the monitor is in energy saving mode and goes out when the power to the backlight is off Press this button to turn on the power to the monitor or if the power is already on to cut the power to the monitor s backlight Press this to open the menu select an item to be adjusted and save an adjusted setting B Button Press this to select the right hand item or increase the value lt 4 Button Press this to select the left hand item or decrease the value AUTO EXIT Button Press this to close the menu cancel the selection of an item to be adjusted cancel an adjusted setting or perform automatic adjustment 8 It is possible to directly adjust the screen brightness by pressing the Point B gt button or button
19. ds Do not place such unnecessary items as cups on the top of the Console Drawer Do not modify or repair the Console Drawer Only licensed personnel may disassemble remove or switch parts such as power supply units that bear a warning mark such as a lightning bolt mark e Only the resolutions and refresh rates specified in Adjusting the Monitor may be set Using settings other than those noted may damage the monitor Contact your place of purchase or a Fujitsu maintenance person if you have any questions To prevent interference it is necessary to adequately isolate the data cables connected to peripheral equipment To cut off the power supply unplug the power cable from the rack power outlet Follow the instructions in the appropriate section in Operation when cleaning the server Keep this manual with the Console Drawer at all times Do not use the Console Drawer as a stepladder or lean against it with it drawn out Doing so may unbalance the rack causing it to fall over Some limited life components such as the LCD etc are included in this product In cases of extended continuous use the performance of these components is easily decreased e To avoid damage to this equipment or personal injury return console drawer to its closed position when not in use 2 2 Moving Console Drawer When moving the Console Drawer to a different location use the box in NCAUTION which it was purchased or a box that protects the product from
20. e procedure in reverse order Take out four screws packed in nylon bag which is taped on the open space area of the rear top panel Make sure the rubber feet on the bottom of the 4 port KVM switch are removed 2 Insert the 4 port KVM switch into the open space area of the rear top panel making sure that the 4 port KVM switch s connectors face out from the rear of the Console Drawer 3 Fasten the 4 port KVM switch in place with the four screws taken in step 1 over the rear top panel metal __ Rubber Feet Xa X x X if FF 4 GS Neo ex i kA a4 ig fg S d Fi f Fi ri F 1 A Z r Ej F jf x SCR la f RN FA i il f it MEC S F p 4 ke Lx 1 i Se ee XJ AO a a A f i Vr JA S 1 T i m 1 BF li E f j j fey j i A pr j i j i f j T df LLL LL L IQ jq L g 4 M ee JM I ML x F Pa i fa a l i F lj j i j N i f j i P f r i li T i i i f j i if j fy fos i OUTPUT 4 4 port KVM Switch DC5V Rubber Feet Screws in i f j Note Make sure rubber feet to be removed in advance ort KVM Switch the 4 Installin 10 4 Connecting and Removing Cables 4 1 Connecting the Cables Unplug all power cables conn
21. ected to related devices from the power outlets 2 Console Drawer I F cable 3 types subject to usage One end for all cables are DVI CN The other end PS 2 I F cable D SUB 2 Mini DIN 6 pin PS 2 CNs USB I F cable D SUB USB CNs Sun I O I F cable D Sub 1 Mini DIN 8 pin CN Connect the keyboard cable mouse cable and monitor cable to their respective ports Then connect the DVI CN end to the console drawer 3 Plug the AC power cable into the Console Drawer power socket 4 Plug all the power cables into the power outlets Connecting the cables to the Console Drawer Case of PS 2 type I F Cable usage Power Socket DVI Connector E M E MM M 9 amp M dEP a f 2 MEE o Da Console Drawer I F Cable D SUB Connec Power Outlet 4 2 Removing Cables Unplug power cables connected to all the related devices from the power outlets and then remove each cable 11 9 Connecting to Multiple Servers with a 4 port KVM Switch installed in the back of the Console Drawer CA N See cautions given in Connecting and Removing the Cables when connecting and disconnecting ports Also cut the power of any affected equipment before you start working on it Refer to the 4 port KVM Switch user s manual as well as this manual for more details You can connect servers in accordance with the 4 port KVM specification 1 PS 2 type of C
22. fter power on O S boot up power off or O S shut down the display position may shift blink or otherwise be disturbed Any native resolution can be displayed in 1280 x 1024 full screen mode by scaling function In this case letters may be blurred and the thickness of thin lines might be uneven This is because the full screen display is made by digital interpolation of the low res output not by physical magnification This is not a display failure and the device can be used normally Although there might be some dots or pixels that are always off black or always on red green or blue this is a natural characteristic of LCDs and is within specification it is not a defect and you can use the device normally 6 7 Keyboard Operation By making use of the Function Fn key if is possible to obtain full keyboard functionality from even a reduced space keyboard key key combinations The extra command keys that are enclosed in billets e g around the perimeter of the keyboard may be accessed by pressing the associated key together with the Function key e g Help Fr Esd The command keys that are not enclosed e g lt compose gt may be accessed by simply pressing the associated key e g lt compose gt lt Windows menu key gt Fig US Keyboard F15 F16 E NumLk Insert Delete Pause 2 SerLk PrtSe SysRa Break s Fn Ctrl Fig EU layout ex UK Keyboard E Ex Ed eae KI F01 Foe F0
23. g uoa ee olia ceca eeu b auteni e eate beanies 30 10 2 WIOMMOFOISDIAY Is Sange ssi desta cauta licaee n a i tenet Leto coelo Loue te Lene cond 30 10 3 Monitor cannot be ad usled oet ebkeo rope ve SE ele brad De vbPer EEE 31 10 4 Other Irregularities in Monitor Display cc ccc ccccceccseeceeeceeece cece eeseeeseeeeeeseeeseeeaeeeseeeaess 31 OROSII TNR A c c m 32 1 Preface Congratulations on your purchase of the server rack mountable Console Drawer SERVIS DRAWER 17 inch hereinafter called Console Drawer this product or this device Using this product will greatly improve the efficiency and functionality of the workspace around your racks Space that was used in previous layouts can now be used more freely due to our compact sliding module design The 17 inch TFT monitor has a resolution of 1280 x 1024 dots with 16 770 000 colors Also it is equipped with a keyboard and 3 button pointing device 1 1 Conventions Symbols and terminology that are used in this manual are described below This symbol indicates the possibility of physical damage such as N CAUTION damage to the Console Drawer or physical injury which may result if the Console Drawer is operated incorrectly by ignoring this symbol Point This logo indicates supplemental information comments or hints e Text that is preceded by a sequence of numbers 1 2 etc means that t
24. he operations must be performed in the indicated order e References to important chapter titles and terminology are in brackets 1 2 Packing List Make sure that the items in the following list were included in the shipping package Console Drawer x 1 4 port KVM Switch Screws x 4 in a nylon bad tapped to the Console Drawer DC Cable x 1 in a nylon bag taped to the Console Drawer Operation Manual this manual x 1 We recommend keeping the box and packing material in which the Console Drawer was purchased They may be required when moving it to another location If something is missing from the package contact your place of purchase or a Fujitsu sales person Similarly as they will be needed when the 4 port KVM switch is installed the 4 port KVM switch screws and DC cable should be left taped to the Console Drawer A CAUTION Please note the safety information in Important Notices 1 Unpack the Console Drawer and check that it has not been damaged in transit 2 Remove the rubber stabilizer from the front left side of the Console Drawer 8 The rubber stabilizer is inserted to prevent the Console Drawer from oint sliding when installing or moving it Be sure to keep it after finishing the installation for when it needs to be used again Latch Lever ae Stabilizer Console Drawer Su Rubber stabilizer removal 2 Important Notices 2 This chapter contains cautions that must be taken when
25. monitor cable properly or not inserted into the socket properly 10 2 Monitor display is strange Symptom Predicted cause Solution O Grid screen that flickers Adjust the focus Vertical stripes are Monitor adjustment is not Adjust clock and then focus visible proper Display is larger or Position is not proper Adjust clock and then position Use of a non standard display Change the server settings to use resolution mode the standard display resolution mode smaller than the monitor screen sometimes no images Power cable is incorrectly Connect the power cable correctly are displayed on connected or not plugged in and make sure the plug is fully monitor fully inserted Letter weights are Focus or clock adjustment is Adjust clock and then focus different across the not proper monitor Resolution of lower than 1280 Letter weights may also be x 1024 has been set intentionally different if digital magnification is used The appropriate monitor resolution is 1280 x 1024 settings in the Monitor Properties 10 3 Monitor cannot be adjusted Symptom Predicted cause Solution OV 0 Automatic adjustment by Automatic adjustment was Make the monitor image as bright AUTO EXIT button does performed with an extremely as possible then press the not work and following dark monitor AUTO EXIT button to redo the messages are background image automatic adjustment displayed AUTO ADJUST
26. onsole Drawer I F cable is required Connect each cable for keyboard mouse and monitor from the Console Drawer to the console port of 4 port KVM switch 2 Use option cables to connect each server s keyboard mouse and monitor port VGA accordingly subject to the available configuration of the 4 port KVM Switch and each server port In details please refer to the 4 port KVM Switch manual The back of the Console Drawer DVI Cable AC Adaptor for 4 Port KVM Switch or DC Cable Attach DC cable to the back of the Console Drawer Due Keyboard MN oz IH ll oH Special KVM Server Cable Server 1 Server 3 p ud cal tll 2 il Erj e WINN e Server 4 l l Server 2 l Connecting the cables to a 4 port KVM Switch O Operation Pull the Console Drawer slowly toward you until the slide rails lock If the slide rails are not locked the Console Drawer can move unexpectedly If they do not lock the weight of the Console Drawer or any person leaning on the Console Drawer may cause it to move suddenly and it may cause injury or damage to the product Be careful not to pinch your fingers when pulling or pushing on the slide module or opening and closing the LCD etc N CAUTION CAUTION Do not apply any significant force while the Console Drawer is pulled N out or while the Console Drawer is used as there is a risk that the Console Drawer may be forced from the g
27. operating the Console Drawer and information related to safety Carefully read this chapter to use the Console Drawer correctly 2 1 Safety N CAUTION Precautions This device conforms to the safety regulations related to information processing equipment such as electronic office machines that are used in an office environment If you have any questions please contact your place of purchase or a Fujitsu sales person To prevent extreme bumping shaking vibration while moving the Console Drawer please use the original shipping container or a similar box in addition make sure if it fits well to the product for protection During installation and before using the Console Drawer carefully read Installation and the section about environmental conditions in Technical Specifications to use the Console Drawer correctly e Moving the Console Drawer from a cold environment to the installation location may Cause condensation to occur Before using the Console Drawer allow it to dry out completely and to reach the ambient temperature of the installation location Make sure that the local power supply voltage is within the acceptable range of the Console Drawer Make sure that the rated voltage meets the specifications of this device Refer to Technical Specifications and the model plate on this device The Console Drawer s power cable is specially certified Do not connect it to anything other than a rack power outlet in order to
28. s or damage CAUTION Turn off the power and unplug the power cable from the power socket Wipe the Console Drawer and monitor with a clean dry soft cloth If the dirt is excessive wipe it off with a damp dry soft cloth that has been thoroughly wrung out after dipping in water Remove dust with a soft bristle brush Clean the keyboard and pointing device with a damp dry cloth 26 8 Technical Specifications Model e Power Specifications Rated voltage range Frequency Rated current e Size Guide Rail Main part 1 Slide rail contracted 2 Slide rail extended 3 2 the LCD are fully opened e Weight e Required Environmental Conditions Operating Temperature e Monitor Panel monitor Resolution Pitch Refresh rate Colors Max Video Signal e Keyboard Layout Number of keys e Pointing Device Model Resolution e Button Number of buttons e Input Device Interface FD 1100MT 100V AC 240V AC 90 60Hz 100V 0 8 A 30mm W x 610 to 855mm infinitely adjustable D x 44 0mm H W x D x H 486 mm x 685 mm x 43 mm 486 mm x 1215 mm x 43 mm 486 mm x 1215 mm x 365 mm 14 0 Kg 0 235 C Water condensation must not occur 17 TFT color LCD Max horizontal 1280 dots x vertical 1024 lines 0 264 x 0 264mm Max 5Hz 16 770 000 dithered Analog RGB Separate Composite Sync US layout EU layout Japanese layout 83 84 87 otatic Touch Pad 22
29. ts affiliates Fujitsu warrants all Product against defects in materials and workmanship for a limited period not to exceed one 1 year from the date of 4 delivery to Fujitsu authorized distributor or authorized system integrator Authorized Company Check with Fujitsu for such Authorized Company Fujitsu s liability under this warranty is limited at Fujitsu s sole discretion to repairing or replacing any component with new or like new components or parts or replacing with a refurbished or alternative product or issuing credit for the purchase price if paid for such Product that was defective at the time delivered to Purchaser provided that Fujitsu will not be liable under this warranty unless i Fujitsu is promptly notified in writing upon the discovery of defects by Purchaser ii the defective unit is returned to Authorized Company transportation charges prepaid by Purchaser iii the defective unit is received for adjustment no later than one year following the date on which such Products were delivered by Fujitsu to Authorized Company and iv Fujitsu s examination of such units shall disclose to its satisfaction that such defects have not been caused by misuse neglect improper installation repair alteration accident improper storage or other action or inaction beyond reasonable practice for such Product This warranty shall be administered and returned to the party from whom Purchaser purchased Product which is an
30. uide rails damage the guide rails or the rack may topple over and cause personal injury or damage to the systems Do not apply force to the monitor screen and not scratch it with any objects or not bring magnetic objects near the Console Drawer They can cause failure or damage to these products CAUTION Note that the corners of the open Console Drawer can be dangerous N if bumped into Always Be careful of whatever operations are done close to the Console Drawer while the Console Drawer is pulled out because it is easy to be injured by hitting the Console Drawer accidentally It is recommended that the Console Drawer be stowed away in the rack when it is not in use or when other nearby servers or peripheral equipments are being used 6 1 Operating the Console Drawer Remove the rubber stabilizer when it is not already removed 2 Push down the latch lever in left side of front end of the Console Drawer and pull out the Console Drawer by the handle until the slide lock clicks into place 5 Before pulling it out make sure that the two screws on the front of the oint Console Drawer are tightly fixed to the rack 13 Guide Rail Cable Duct Slide Rail Console Drawer Latch Lever Guide Rail Slide Rail LCD Lock Latch Lever e e Z N PA Rubber Stabilizer Z 7 7E NC Pulling out the slide module 14 3 Push up on the LCD lock behind the han
31. wer seeseesseeseeseseeeeen enne nnne nnne nnne nnns 13 6 2 Adistrg thie MIOFIOE aos oceooova oc iao Sid pu eov E Nate Doo Noo vog a oO Mao Ud pa var vaa ed 15 OZ PIOUS UG TS MONOT go t 16 6 3 Basic Adjustment Procedure uoscoccundeciexodecadisios nddquad datas qac indadadexmdedodexiu eti odes eds inea sados 17 04 Man Men Nems cstekeistotetetstoteburScotstasratutsi statt tacstatttecseatu te statt tecstal R ratiooe son 18 6 5 Resolutions and Refresh Ral6s iibi ebbe tbe Ev e obe obe ebd rb ebore tdeo bise bdea boobs bats 19 Sre cTienta BE o op d 19 6 7 Keyboard OPSTAO Miscarii E Em 20 6 9 Polnting Device OQperalOi eisien a E EEE A 22 0 9 Hot key and Reset BUNONS ooi oio aro ovo E evo e a or iiao b etos e ea A O A 23 DVO MIS ore roodo CR ERE ETT OTT 23 OT SIOWIg CoHsole DEIAWOLF ucdeidctoncanicOSotuedciont qoncosec nei eonien tendido decidere coccdenenccoteot Toc duode niduies 24 7 Cleaning the Console Drawer esses 25 8 Technical Specifications seeeseeeeeeeeee 2f 9 Optional Accessories Sold separately 29 9T phlional CADES inse a ias txonetiatieodic tat ixcnc tat dodc Umi ode adeunt e etie etd 29 92 Optional elei c e E 29 10 TFOUDIESIOOUING eretcumehmas Got ct emi etvadbnc tem edv Kent Sole si Un be 30 10 1 Noummage displayed on MONIO aote Sese eau aod ea e
Download Pdf Manuals
Related Search