USER`S MANUAL - MARUSON Technology
Contents
1. cord lose Check input power AC Fuse burnout Replace fuse if problem remains call for service than the rating Backup time is less Battery is not fully charger failure Recharge the battery for at least 6 hours re test the backup time If problem remains call for service 15 Function SPECIFICATIONS 2500VA 3000VA Modem Phone RJ 11 RJ 45 Protection Lightning Surge 480joules Protection AVR Auto Voltage Boost Buck Regulation DC Start Function Yes Auto Restart UPS Yes Over Under Voltage Yes Protection Environment Safety Standard CE EN50091 1 EN62040 1 1 EMC Standard FCC Part 15 Class B CE EN50091 2 EN55011 EN61000 3 2 EN61000 3 3 Operating Temperature 0 40 C 32 104 F Relative Humidity 0 95 non condensing Audible Noise lt 40dB at 1M Dimension 19 2U 18 31 in 19 2U 465 Physical D W H in mm Net Weight 57 32lbs 26kg 60 63lbs 27 5kg Specifications may change at any time without notice trade marks belong to their respected owners 14 SYSTEM CONCEPT The purpose to present this chapter is to give you more precise conception about how UPS works 1 Block Diagram OUTPUT N F Fig 1 shows how UPS works 2 Normal Operation There are two main loops when AC Utility normal the AC output loop and the battery c2. in CCCV battery charger and battery over drain protection No load auto shutdown Dip switch setup Load level and Battery level display Buzzer alarm auto reset Dip switch setup Auto restart when AC recovery Cold start function Dip switch setup Tel Modem Fax Internet surge suppression Bundle software Automatically save your valuable files before auto shutdown 2 TROUBLE SHOOTING If the UPS failed to operate properly please review the following checks firstly If the problem remains please consult sales agent for service Is the Master power switched on Is the UPS plugged into a correctly working outlet Is the line voltage within the rating specified Is the fuse on the rear panel blown Is the UPS over loaded Is battery not fully charged Dead battery Charger failure Please provide the following information when call for service 1 Model number serial number 2 Date of the problem occurred date of purchase 3 Full description of the problem including load LCD and alarm status installation condition working environment etc Trouble Shooting Chart Problem Possible Cause Caution To Take UPS not on No light and no alarm Front panel switch in off position Turn on switch Rear panel fuse burnout Replace fuse restart UPS Power cord lose Check input power every few seconds light and alarm beeps No Line on
3. MARUSON UPS SYSTEMS USER S MANUAL 1 Edition Maruson Technology Corp Uninterruptible Power System MARUSON TECHNOLOGY CORP m a Info Marus Web www MarusonUSA com Power Solutions for AM Your Needs Maruson Technology Corp all rights reserved Maruson is a registered USA company PRO Rack 01 NOTES The following parts will be sent together in the box UPS ale 2 USB cable 3 RS 232 cable 4 RJ11 cable 5 Power Management Software 6 Ears amp screws for tower or rack mounting IMPORTANT SAFETY INSTRUCTIONS Thank you for selecting this uninterruptible power system UPS It provides you with better protection for connected equipment Please read this manual This manual provides safety installation and operating instructions than will help you derive the fullest performance and service life that the UPS has to offer Please save this manual It includes important instructions for the safe use of this UPS and for obtaining factory service should the proper operation of the UPS come into question Please save or recycle the packaging materials The UPS s shipping materials were designing with great care to provide protection from transportation related damage There materials are invaluable if you ever have to return the UPS for service Damage sustained during transit is not covered under the warranty CONTENTS PAGE AON wae neteneencinehandanteuc sn cten
4. T OVERLOAD it over 100 To simulate AC failure Simply by disconnecting the AC power can help to insure whether UPS is in good condition or not It is designed to alarm every 3 seconds and with BACK UP LCD light on when simulation starts If the CUT OFF LCD is on it means UPS fault or BATTERY fault Then you have to contact your local service center 5 When battery approaches low level alarm will beep every second until auto shut down 6 The 4 conditions UPS will automatically shut down a Battery low b Short circuit c Overload d UPS fault COMPUTER INTERFACE The computer interface DB9 port on the back of the UPS may be connected to a host computer This port allows the computer to monitor the status of the UPS and control the operation of the UPS The iMate provides complete On Screen power management to the UPS and computer systems Its major functions normally include some or all the following Real time UPS status on screen All history records in memory Auto orderly shutdown for computer amp UPS Multi server support Auto file save even without filename preset Scheduled switch on off daily or weekly Pin out information PIN Description PIN1 Battery low normally open active close Output PIN2 N C PIN3 Common Ground PIN4 Remote shut down keep this pin high Input 5 12V for 3S will turn off the UPS 5 N C PIN6 N C PIN7 Must keep in high state Input PIN8 Line fa
5. age Batt Mode 110 115 120VAC or 220 230 240 10 Frequency 50Hz or 60Hz 1Hz auto sensing Output Waveform Simulated Sinewave Transfer Time lt 6ms Typical Outlets Battery Surge only Nema 5 15R 6 3 Battery Type Optional 12V 7AHx2pcs 4pcs 12V 9AHx2pcs 4pcs Recharge Time 5Hrs to 90 after complete discharge User s Replacement Yes hot swappable W O Turning off the UPS Battery Battery Protection Over discharge protection amp Short circuit protection by fuse Advanced Battery Management Advanced Battery Management Battery Back up Time It depends on connecting loads and external battery packs External Battery Bank Optional N A LCD display for AC normal Backup AVR protection Load and Indicator LCD Battery level Overload and UPS cut off Alarm Buzzer on for Back up mode Battery low Overload AC fuse and Electronic circuit Line mode Electronic circuit Output Short Protection Function Back up mode Communication Port RS 232 amp USB Shutdown Software for Windows 95 98 NT 2000 ME XP Vista Remark Battery with 4pcs is for long backup 11 BATTERY FACTS The battery is the only periodically serviceable parts in the UPS An expected life is approx 3 5 years However frequent long discharges or ambient temperatures above 80 F will shorten battery life Therefore it is recommended to replace the batteries every 3 years after initiating the unit Recharging the batteries every 3 month
6. anasonic 1 800 SAV LEAD YUASA 877 288 7722 e LONG 202 719 4978 10 INSTALLATION AND OPERATION Upon receipt of the UPS inspect the shipping carton for damage If there is any obvious damage immediately report it to the selling dealer or the delivering carrier If there is no damage to the shipping carton unpack the unit and inspect the unit for damage The UPS is designed for installation in a protected environment within a temperature range from 32 F to 104 F and relative humidity of 0 90 without condensation Do not block inlets and outlets Install the system in a location free from excessive dust and chemical fumes Check the identification label to verify the UPS voltage and power rating match the available line voltage and load requirements Installation 1 Check if the main switch on the UPS front panel is in the off position and insure that the voltage of the AC utility source corresponds to the nameplate on the UPS rear panel 2 Plug the power cable into the grounded socket If indicators of LINE ON amp CUT OFF LCD light on it mean AC power is normal although UPS is under CUT OFF status it still will automatically start to charge by itself 3 Push the main switch then the Load Level LCD will light on for 2 seconds and CUT OFF LCD will light off The UPS will then get ready and start to work normally 4 Connect your PC with UPS and then turn on PC Be sure to check the Load Level LCD indicator and DO NO
7. at any time without notice All trade marks belong to their respected owners 12 OVERVIEW Front Panel 1 Master Power Switch Turn on off the UPS 2 Line On AC Normal 3 AVR Protection LCD When AVR is working under protection mode the light will turn on 4 Back Up Battery in back up 5 Over Load If the UPS is overloaded the light will turn on and the alarm will sound continuously 6 UPS Cut Off Overload or Cut off 7 Battery Level A bar graph showing how much of the UPS battery is being used 8 Load Level A bar graph showing how much of the UPS power is being used 9 Hot swap battery 10 UPS Test Switch When UPS is working under AC mode it also activates UPS s self test by press the bottom Rear Panel 1 Outlets 2 AC Input 3 AC Fuse 4 Tel Modem Spike Projection Port Telecom transfer ports provide users to extend the applications Communication Interface Port This socket combines relay contact signals and RS 232 signals Option on 9 connector UPS Function Set up Communication Interface Port USB Port Surge Protection Only External Battery Connector Picture Front Panel AE BS Gael LAN 0 25 50 75 100 SPECIFICATIONS Capacity VA 1250VA 1750VA Voltage 110 115 120VAC or 220 230 240VAC Input Frequency 57Hz 63Hz or 47Hz 53Hz auto sensing Input Plug 5 15P Volt
8. eehende isi CsenaanGe tener 1 INTRODUCTION SYSTEM DESCRIPTION ti rccoeonchsorbebaugnalvgscenestihiiincenees 2 Pea PT Ee eat te lth ek T 2 SYSTEM CONCEPT BLOCK 3 AC UTILITY RAM FB 4 OVERVIEW PRON PANEL oe ee ee eae eat 5 READ PANEER tis elected reed 5 PICTOR mere ea edee as eRe oe 6 INSTALLATION AND 8 GOMPUTERAUNTEREAG Bice 9 OCP PY are 10 SPECIFICATIONS areas en 11 gt TROUBLE SHOOTING ese 13 NOTES NOTES CAUTION The UPS contains voltage that is potentially hazardous All repairs should be performed by qualified service personal The UPS has its own internal energy source battery The output receptacles may be alive even when the UPS is not connected to an AC supply The UPS is suitable for computers and electronic equipment with substantially rectifier or capacitive loads not suitable for electronic equipment with significant inductive loads such as motors amp fluorescent lamps Be sure to operate within the power rating of the UPS Below 1 2 or 1 3 of rated power is recommended for longer backup time amp longer battery life Do not place the UPS near e
9. harging loop The AC output gets power from AC utility input and pass through AVR to support power to load In the same time the AC utility input is converted by AC DC CHA and support charging power to charge batteries OUTPUT 7 4 Fig 2 shows how UPS works when AC Utility normal 3 SYSTEM CONCEPT 3 AC Utility Failure If AC utility fails the UPS quickly detects the problem and activates the inverter The inverter The DC AC inverter changes DC power from the batteries into AC and provides continuous uninterruptible power to load OUTPUT AVR INV Fig 3 shows how the UPS works when AC Utility Failure Capacity SPECIFICATIONS VA 2500VA 3000VA Input Voltage 110 115 120VAC or 220 230 240VAC Frequency 57Hz 63Hz or 47Hz 53Hz auto sensing Input Plug 5 20P L5 30P Voltage Batt Mode 110 115 120VAC 220 230 240 10 Frequency 50Hz or 60Hz 1Hz auto sensing Waveform Simulated Sinewave Transfer Time lt 6ms Typical Outlets Battery Surge only Nema 5 15R 20R 6 2 Nema 5 15R 20R 6 2 Nema 5 15R 1pc for surge Nema 5 15R 1pc for surge L5 30R 1pc for battery Battery Battery Type Optional 12V 7AHx4pcs 12V 9AHx4pcs Recharge Time 5Hrs to 90 after complete discharge User s Replacement Yes hot swappable W O Turning off the UPS Battery Pro
10. il normally open active close Output PINS N C D SUB 9 Pin Female Connector 1 Low Battery Contacts Z 8 Mains Failure Normally o o 3 Open 4 UPS Shut Down
11. s is necessary because it may cause the batteries to over drain WARNING Only a qualified technician should replace the battery Batteries have high short circuited current capacity mistakes in connecting or disconnecting can cause connections to arc or weld and could cause severe burns STORAGE The UPS should only be stored if the battery is fully charged Avoid storage temperatures above 80 F as battery life is significantly shortened Every 90 days remove the unit from storage and plug it in for 24 hours to recharge the batteries Batteries may be damaged if left in storage and not recharge every 90 days IMPORTANT NOTICE Please use same type and same rating of batteries for replacement Do not replace it with the battery that exceeds specified rating Rear Panel PRO 2500XRT PRO 1250 1750ART w o external battery connecter 9 4 BET PRO 3000XRT 94 Your UPS contain Non Spill Sealed Lead Batteries On the battery you will find the battery name Please refer to the chart on the right for recycling information Other brand s of battery please contact Maruson Technology If outside of USA or Canada please contact your local authorized distributor If you have any question regarding to our product please contact us at 1 888 MARUSON or e mail us at Custsrv MarusonUSA com Battery Name Recycling inside the USA CSB Battery 1 800 RE USE PB 7387372 P
12. tection Over discharge protection amp Short circuit protection by fuse Advanced Battery Management Advanced Battery Management Battery Back up Time It depends on connecting loads and external battery packs External Battery Bank Optional 12V 7AHx4pcsx2sets 12V 9AHx4pcsx2sets Indicator LCD LCD display for AC normal Backup AVR protection Load and Battery level Overload and UPS cut off Function Buzzer on for Back up mode Battery low Overload Output Short Protection AC fuse and Electronic circuit Line mode Electronic circuit Back up mode Communication Port RS 232 amp USB Shutdown Software for Windows 95 98 NT 2000 ME XP Vista 13 SPECIFICATIONS 1250VA 1750VA Modem Phone Protection RJ 11 RuJ 45 Lightning Surge 480joules Protection AVR Auto Voltage Function Regulation Boost Buck DC Start Function Yes Auto Restart UPS Yes Over Under Voltage Protection Yes Safety Standard CE EN50091 1 EN62040 1 1 EMC Standard Environment FCC Part 15 Class B CE EN50091 2 EN55011 EN61000 3 2 EN61000 3 3 Operating Temperature 0 40 C 32 104F Relative Humidity 0 95 non condensing Audible Noise lt 40dB at 1M Dimension 19 2U 18 31 19 2U 465 mm Physical D W H in mm Net Weight 34 17lbs 15 5kg 55 12lbs 25kg Specifications may change
13. xcessive humidity under sunshine or close to heat emitting sources If the UPS is out of order please detach power cord and consult your dealer right away Do not remove cover if there is no serviceable part inside The unit should be supplied by grounded source Do not operate the unit without ground source The socket outlet should be installed near the equipment and be easily accessible Do not plug the UPS power cord into itself That will result in a safety hazard Installation should be performed by a qualified technician or electrician in accordance with local electrical codes INTRODUCTION System Description The product is line interactive UPS with the newest technology and powerful function The Line Interactive UPS is with AVR function allows input voltage range from 75 to 125 including on line voltage boost up amp buck down Ideal protection equipment for critical connected loads In addition This UPS provides advanced single telephone line or modem surge suppression through the modular connectors on the back panel The Line Interactive UPS and iMate monitoring software makes our computer operate intelligent and provides you with the ability of perfect protection of your critical devices Features VV VV VV VV VV V V Line interactive design User friendly LCD display Provide boost and buck AVR to stabilize input voltage Provides lightning surge overload and short circuit protection Built
Download Pdf Manuals
Related Search