Home

PT-E831H-AC431x, PT-E831HS

1. Figure 9 1 Exchange the battery 1 CONTEC PT E831H PT E831HS User s manual 111 9 Appendix 3 Draw the battery out of the holder and unplug the connector Battery Wty Bays Figure 9 2 Exchange the battery 2 4 Plug the connector of new battery and fit the battery into the holder 5 Clamp the cable 6 Mount the cover The tightening torque range is 5 to 6 kgf cm Point If the expansion board loaded in the add on unit is not recognized in the operation check the mounting state again WARNING Do not attempt to replace the battery as inappropriate battery replacement poses a risk of explosion For battery replacement contact your retailer as it must be performed as a process of repair A CAUTION Do not remove PT A6BAT during turning on Doing so may lead EPC System Monitor not be able todetect low voltage depending on the situation of the electric charge which is stored up on thecondenser that is connected with PT A6BAT in parallel CONTEC 112 PT E831H PT E831HS User s manual 10 List of Options 10 List of Options Battery Lithium ion battery PT E73BAT Screen protective sheets PT E82PSC PT A6BAT CF Card Front interface unit PT E73FRU PT E73FRUS IDE Power Supply Cable CF 1GB B CF 2GB B CF 4GB B CF 8GB B Lithium battery for RTC BIOS Lithium ion battery pack for resume function 15inch scre
2. Lamp Color No Item Button Description Normal Alarm Error Reset Exchange forecast result and the related alarm aa A6BAT 1 Exchange message exchange warning low voltage Detect new K one Forecast Reset button alarm after reset Do this operation when exchanging PT A6BAT Reset PT E73BAT s exchange forecast result and the EP73BAT 2 related alarm message exchange warning low voltage 15 exchange forecast Forecast result will be added up from 0 00 after reset None reset button Do this operation when exchanging PT E73BAT This item is masked if No use is set in area of Resume Function Reset PT E73BAT s charge discharge count result and the i PT E73BAT related alarm message exchange warning Charge discharge A 16 Count number will be added up from 0 after reset Do this None count Reset button A ae A operation when exchanging PT E73BAT This item is masked if Not use is set in area of Resume Function Reset exchange forecast result of encoder battery of servo amplifier that is connected to PT E Detect new alarm after ENC BAT Exchange p 17 reset Do this operation when exchanging encoder battery None Forecast Reset a i This item is masked if Not use is set for this item in option setting Push this button the following screen is displayed WU Temp MAlara A Event Lo 18 g None button Up to 500 cases occurred event contents or occurring times are displayed The
3. Figure 3 6 Distances between this product and its vicinity An CAUTION Do not install this product into the fully sealed space except the case in which the internal temperature is adjustable by equipment such as air conditioner Troubles such as operational malfunctions could be occurred by the temperature increase caused by long term usage CONTEC PT E831H PT E831HS User s manual 15 3 Hardware Setup CONTEC 16 PT E831H PT E831HS User s manual 4 Each Component Function 4 Each Component Function Parts Identification PT E831H PT E831HS q 0 a Ane e m A PT E831H PT E831HS Figure 4 1 Parts Identification CONTEC PT E831H PT E831HS User s manual 17 4 Each Component Function Table 4 1 Parts Function No Name Description 1 Display TFT color liquid crystal display with touch panel CF card slot You can insert a CF card in the slot Built in disk drive The built in disk drive has primary master drive and primary slave drive DC power supply Connect an IDE power supply cable for feeding the peripheral device CD ROM drive connector HDD etc that is connected with IDE Connect an IDE compatible peripheral device CD ROM HDD etc 4 IDE connector i It will be secon
4. Allows you to set the Dynamic Video Memory Technology DVMT memory size ti Move ENTER Accept ESC Abort Boot Display CRT DVI a I CRI LVDS a Boot Display Choose an active display at the time of starting tj Move ENTER Accept ESC Abort Panel Type LVDS tees E Panel Type KIE ss 1 Set panel type that the system supports Do not change the setting tJ Move ENTER Accept ESC Abort Boot After SWON Set whether or not to do system start setting Do not change the setting CONTEC PT E831H PT E831HS User s manual 95 8 BIOS Setup Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals The first screen shows three main items for user to select Once an item selected a submenu appears Details follow Phoenix AwardBlOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter Item Help gt Onboard Device Press Enter gt Superl0 Device Press Enter Menu Level gt t gt Move Enter Select PU PD Value Fi10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 8 Integrated Peripherals CONTEC 96 PT E831H PT E831HS User s manual 8 BIOS Setup OnChip IDE Device Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device On Chip Primary PCI IDE IDE Primar
5. 65 will be opened automatically when error occurring alarm occurring If not choose this item EPC System Monitor s Windows is If choose this item EPC System Monitor s start screen will be f Paar be k monitor screen refer 5 minimized when minimized and put in task bar at the moment of starting PAE A to p 65 is displayed at starting Display the screen and operate when necessary the moment of starting CONTEC PT E831H PT E831HS User s manual 69 7 Resume Function EPC System Monitor Save the current settings The settings will be available from next time starting The following message is displayed if the settings have been changed EPC System Monitor EASA EEN EL 6 OK button Setting contents is changed ELAN SID ABEL AIST Setting contents will be available after next start Push OK button Set UP screen is closed 7 CANCEL button Cancel the setting contents and close the setting window Save the current setting and restart The following message is displayed if the settings have been changed EPG System Monitor EASA EEN EL 8 Apply button Setting contents is changed RELAIS DA ELE Restart Windows for setting contents available Push OK button close Set UP screen and restart Windows 1 Using EPC System Monitor s start option set whether use resume function or not Refer to p 73 for setting method 2 WDT is abbreviation of Watch Dog Timer
6. As Windows OS is not installed in the external HDD you need to setup Windows when powering on PT E for the first time A CAUTION When customer installing Windows OS note that not only OS but also PT E dedicated drivers should be installed For installing OS commercially available CD ROM for Windows setup and PT E dedicated driver CD are necessary The customer needs to purchase CD ROM for Windows setup Contact our agent or sales office if you need PT E dedicated driver CD CONTEC PT E831H PT E831HS User s manual 33 5 Startup and Termination Write protect Executing write protect can prevent from deleting the important data preserved in the CF card and overwriting them by mistake This section describes how to execute and release write protect to a CF card A CAUTION Do not use the CF card after removing it from PT E Write protect is only available for the CF card that is installed in PT E Method of Executing Write protect 1 Click Start on taskbar Move the cursor to All programs P Accessories and click Command Prompt E Accessibility E Communications 7 Entertainment 7 System Tools mmand Prompt Click here TD Notepad Y Paint Q Windows Explorer a WordPad Administrator m Startup amp uoo Internet Explorer Figure 5 1 Command Prompt 2 The command prompt is started Input command ewfmgr C enable and th
7. When touching the picture of the button in Mouse window the button shown in dark blue is switched The button shown in dark blue becomes the active button Touch operation right after active button is switched is the operation of mouse button When left button is active When right button is active Figure 6 11 Event Selector Window Function of Touch Panel Driver Make necessary settings for touch action This section describes how to make these settings 1 Click Start on taskbar Move the cursor to All Programs P and click Operation Setting Administrator f Accessories I Startup Internet Explorer Outlook Express amp Shortcut to StartUP ET ScreenWorks Log OFF o Turn OFF Computer Click here Figure 6 12 Settings button CONTEC PT E831H PT E831HS User s manual 49 6 Setting the Touch panel Driver 2 Touch Panel Driver Properties window is displayed Click tab of setting item to set touch panel driver Pointer Device Properties x 1 gt Devices Hardware Settings Advanced Events General Windows Calibration Status About The following devices are installed Controller Whole Desktop Interlock COM DMC TSC 10 Series Serial Calibrate 2 8 4 5 6 7 Figure 6 13 Pointer Device Properties 1 Setting tabs Click tab to select setting item General Calibration Devi
8. CONTEC 70 PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor 3 Error Message If there is a setting error the corresponding error message is displayed Table 7 3 Error Message Check Ie EPC System Monitor SEPAIS Setting data error In case of selecting Timer Set setting time is out MEE Timer Set of range or not set SEDE EE PORE El RESTE A Setting data is out of range of selected operation mode or no setting EPC System Monitor REFALI Setting data error In case of setting Use for WDT WDT time is out of WDT I4RJ WDT Setting range or not set BRET REE E EEN TEE Ao Setting data is out of range or no setting Status Output Function Output monitor state of H W and alarm state to user 1 F Windows shared memory or CB CW memory CB CW memory is common memory area for screen design software HMI Designer that is made by our company and other user s application CB CW memory can be used to transfer data and communicate There are two kinds of memories Bit memory CB and Word memory CW Table 7 4 Status Output Function Output Memory User application Windows Access the shared memory with application such as VC etc and display them on Shared Default user screen Memory a Display by user screen that is created by HMI Designer CB CW Set head number of i Po i b Access CB CW memory with application such as VC etc and display them on Mome
9. Events General Windows Calibration Status About Communication Port Settings gt Com port COM1 rt uto Detect FIFO f8 X 2 As D Address fo Baud rate jo Check port 0 zi IRQ p Parity 0 4 Data bits 8 m Stop bits Calibrate Test Cancel Apply Help Figure 6 18 Hardware tab 1 Settings Shows the controller to be used 2 COM Port Set serial port that is connected with controller 3 Auto Detect If enabled when windows start up the serial port connected the controller is detected automatically 4 Information of communication port Show the information of the serial port connected with the controller CONTEC PT E831H PT E831HS User s manual 55 6 Setting the Touch panel Driver Action Settings Used to adjust the reaction time or the touch action when touching a touch panel Pointer Device Properties xl Devices Hardware Settings Advanced Events General Windows Calibration Status About EPA ARO Eee ES ROS me I Use liftoff packet 6 2 _ _ gt Top time M 3 3 E t 2 4 1 stablization po Ee A 5 PA y A AENA Defaults 7 Calibrate Test Cancel Apply Help Figure 6 19 Settings tab 1 Click time Click time is a short time interval that the driver uses in the button click logic that uses time intervals between clicks 2 Tap time Tap time is a shor
10. F5 Previous Values Figure 8 11 SuperIO Device Table 8 12 Super I O device Selections ESC Exit F1 General Help F7 Optimized Defaults Onboard Serial Port 2 Set whether or not to use Serial Port 2 Onboard Serial Port 3 Set whether or not to use Serial Port 3 Onboard Serial Port 2 Disabled Enabled t4 Move ENTER Accept ESC Abort Onboard Serial Port 3 Disabled Enabled ty Move ENTER Accept ESC Abort 102 CONTEC PT E831H PT E831HS User s manual 8 BIOS Setup PnP PCI Configuration Setup This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Resources Controlled By Auto ESCD Menu Level gt x IRQ Resources Press Enter PCI VGA Palette Snoop Disabled I gt Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 12 PnP PCI Configuration Setup Table 8 13 PCI PnP PCI Configuration Setup Selections Reset Configuration Data
11. Operating ambient Front display section is 0 to 40 C temperature other than display section is 0 to 55 C 1 2 Storage ambient temperature 20 to 60 C Operating storage 10 to 90 RH 60 or less wet bulb temperature non condensing lambient humidity Vibration resistance f Based on JIS B3502 IEC61131 2 Shock resistance No oily smoke no corrosive gas no flammable gas no so much conductive dust no Operating atmosphere direct sunshine As well as storage environment X A By noise simulation with noise voltage 1 500Vp p noise width lus and noise Noise resistance q frequency 25 to 60 Hz Protection structure IP65f equivalent front section 1 Electrical currents that are supplied to external devices including those are connected to expansion slot USB port and external DC output only PT E831HS should be 5V 2A 12V 1A or less 2 When using both 2CH Ethernets in 1000BASE T please use PT E under the environment where the operating ambient temperature is Front display section is 0 C to 40 C other than display section is 0 C to 45 C CONTEC 8 PT E831H PT E831HS User s manual 2 System Reference Display Optical Specification Table 2 3 Display Optical Specification Visual eee 80deg eee Display 80deg Visual ET Monochrome 80deg ET 80deg Surface brightness Display in white 200cd m2 250cd m 2 at center Surface brightness represents a numerical value per displ
12. Macros 6 Defaults 7 Calibrate Figure 6 20 Advanced tab 1 2 3 4 5 CONTEC Sample rate Determine the percentage of pointer device data packets that are passed on to the mouse driver This should normally be set to 100 Touchdown filter Specify the initial number of touch packets before sensing a touchdown Sound pitch Set the frequency of the beep The bigger the setting value is the higher the beep becomes It becomes maximum volume near setting value 2000 from the buzzer characteristic Sound duration Sets the length of the beep The bigger the setting value is the longer the beep becomes Check items 1 Swap X Y Normally the cursor appears in the XY coordinate position touched on the screen However the cursor can be displayed in the position opposite to the XY coordinate position touched 2 Enabled Check the checkbox to make touch operation available When doing the touch operation don t remove the checking 3 Initialize Indicates that the device s initialization macro if it exists it will be executed 4 Sound Enables or disables the Sound option that accompanies simulated button presses PT E831H PT E831HS User s manual 57 6 Setting the Touch panel Driver 5 Anchor mouse If enabled mouse cursor is fixed 6 Macro M button Define the controller macros Some controllers can accept commands to change the internal settings 7 Defaults button
13. 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http www contec co jp English http www contec com Chinese http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 09272011 09272011 Management No NA01509 Parts No LYNE751
14. Copyright 2011 CONTEC CO LTD ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD CONTEC CO LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC CO LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product About the handling of the battery and the storage battery in E U Signatory Note This symbol mark is for EU countries only This symbol mark is according to the directive 2006 66 EC Article 20 Information for end users and Annex II This symbol means that batteries and accumulators at their end of life should be disposed of separately from your household waste If a chemical symbol is printed beneath the symbol shown above this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration This will be indicated as follows Hg mercury 0 0005 Cd cadmium 0 002 Pb lead 0 004 These ingredients may cause serious hazardous for hum
15. Disabled Enabled Reset Configuration Data Normally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the operating system can not boot ti Move ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 103 8 BIOS Setup Resources Controlled By Auto ESCD Manual Resource Controlled by The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices If you select Auto all the interrupt request IRQ and DMA assignment fields disappear as the BIOS automatically assigns them Move ENTER Accept ESC Abort CONTEC 104 PT E831H PT E831HS User s manual 8 BIOS Setup IRQ Resources Phoenix AwardBlOS CMOS Setup Utility IRQ Resources IRQ 3 assigned to PCI Device Item Help IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device Menu Level gt IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device Legacy ISA for devices IRQ 11 assigned to PCI Device compliant with the IRQ 12 assigned to PCI Device original PC AT bus IRQ 14 assigned to PCI Device specifications PCI ISA IRQ 15 assigned to PCI Device Pnp for devices compliant with the Plug and Play standard wheth
16. E directly Doing so can malfunction or fail the PT E When disconnecting the cables connected to the PT E do not hold and pull the cable part Doing so can cause damage to the PT E and or cables or a malfunction due to poor cable connection Do not block the air vents Doing so can cause a fire When carrying the PT E always do it after powering off the PT E Also disconnect all connection cords Not doing so can cause a fire or electric shock When the equipment will be left unused for an extended period of time power off the PT E Not doing so can cause a fire due to accumulated dust Before starting the fitting of the expansion board or memory always touch any metallic area Starting the work with your body charged with static electricity can damage the electronic parts Component Life 1 Battery The internal calendar clock and CMOS RAM are backed by a Lithium primary battery The backup time at a temperature of 25 C with the power disconnected is 10 years or more 2 CF The OS installed model uses a CF card in the OS storage area Estimated failure rates 100 000 rewrite cycles 500 000 hours MTBF 3 Touch panel The operating lifetime of the touch panel is at least 1 million touches as tested by mechanical touching under 300g of force at a rate of two presses per second 4 LCD backlight Display brightness decreases over time with use The operating lifetime of the backlight is 50 000 hours the tim
17. Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 4 Onboard SATA 0 Onboard SATA 1 The IDE adapters control the external HDD Use a separate sub menu to configure each HDD Use the legend keys to navigate through this menu and exit to the main menu Use Table 8 4 to configure the hard disk Table 8 4 IDE Adapters Press Enter to auto detect the HDD on this channel If IDE HDD Auto detection Press Enter detection is successful it fills the remaining fields on this menu None Set the HDD specifications Normally specify Auto Extended IDE Drive Auto When using an old HDD that is not recognized by Auto setting Auto Display your HDD Disk drive capacity Approximated Note that this size is Capacity erdiaias usually slightly greater than the size of a formatted disk given by a disk checking program The following options are selectable only if the IDE Channel 0 2 Master Slave item is set to Manual and CHS item is set to Manual A Min 0 Y A Cylinder Max 65535 Set the number of cylinders for this HDD Head Mig D Set the number of heads for this HDD Max 255 Precom Min 0 Warning P Max 65535 Setting a value of 65535 means no HDD j 9 M in 0 kkkk Max 65535 ee a EA Min 0 Max 255 Number of sectors per track CONTEC PT E831H PT E831HS User s manual 85 8 BIOS Setup Advanced BIOS Featur
18. PT E s operation status VCore VMEM 3 3V 5V 12V 1 05V 3 3VSB 5VSB Voltage Battery Systeml Temp System2 Temp CPU Temp NAS m pan V 3 V 1 V 3 V 5 V 3 69 V C C Table 8 15 PC Health Status Vcore VMEM 3 3V 5V 12V 1 05V 3 3VSB 5VSB Display current voltage values Voltage Battery System1 Temp System1 Temp Display current system1 temperature System2 Temp System1 Temp Display current system1 temperature CPU Temp CPU Temp Display current CPU temperature CONTEC 106 PT E831H PT E831HS User s manual 8 BIOS Setup Defaults Menu Selecting Defaults from the main menu shows you two options which are described below Load Fail Safe Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Fail Safe Defaults Y N N Pressing Y loads the BIOS default values for the most stable minimal performance system operations Load Optimized Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load setup Defaults Y N N Pressing Y loads the default values that are factory settings for optimal performance system operations CONTEC PT E831H PT E831HS User s manual 107 8 BIOS Setup Supervisor User Password Setting You can set either supervisor or user password or both of then The differences between are SUPERVISOR PASSWORD ca
19. all settings click Calibration C button El Pointer Device Properties x Devices Hardware Settings Advanced Events General Windows Calibration Status About Calibration Settings For Calibration Modes Device 1 E Normal z Add Remove Calibration Points p 4 Calibration Timeout maje TF Transparent Background Check here Test Cancel Apply Help Figure 6 6 Pointer Device Properties 3 The calibration window is displayed make calibration following the procedures in p 43 44 CONTEC PT E831H PT E831HS User s manual 45 6 Setting the Touch panel Driver Test Used to check the recognition speed of system when screen is touched including touch panel operation and calibration accuracy This section describes how to do an operation test for touch panel 1 Click Start on taskbar Move the cursor to All Programs P UPDD and click Test Administrator Accessories T Startup Internet Explorer gt Event Selector C Outlook Express amp Shortcut to StartUP I ScreenWorks Log OFF a Turn OFF Computer Click here All Programs Figure 6 7 Test button 46 CONTEC PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 2 Test window is displayed Touch the screen and move touch pen to draw a line or write some characters Figure 6 8 Test window 1 Grid Press Grid button
20. and a display to this product using appropriate cables STEP3 Turn on the power After verifying that you have correctly followed steps 1 and 2 turn on the power If you find any abnormality after turning on the power turn it off and check to see if the setup has been performed properly STEP4 Set up BIOS By referring to Chapter 8 set up BIOS This setup requires a keyboard and a display Before using this product be sure to execute LOAD SETUP DEFAULTS to initialize the BIOS settings to their default values See Chapter 8 Main Menu CONTEC PT E831H PT E831HS User s manual 11 3 Hardware Setup Hardware Setup Before you start be sure that the power is turned off Remove only those screws that are explained Do not move any other screw How to Mount PT E831H PT E831HS 1 The following panel cutting is needed to mount PT E The plate thickness of the mounting panel is maximum 5 0 mm 0 20 inch The plate thickness of the mounting panel is minimum 1 6 mm Y i Unit mm Figure 3 1 Dimensions of Panel Opening PT E831H PT E831HS 2 Put PT E into the mounting hole Figure 3 2 How to Mount PT E PT E831H PT E831HS CONTEC 12 PT E831H PT E831HS User s manual 3 Hardware Setup 3 Place the mounting fittings in the holes of PT E make the latches catch theholes Mount four mount fittings on the upside and downside holes of PT E Fi
21. determined by the keyboard controller in your system When Enabled you can select a typematic rate and typematic delay Typematic Rate Chars Sec When the typematic rate setting is enabled you can select a typematic rate the rate at which character repeats when you hold down a key of 6 8 10 12 15 20 24 or 30 characters per second Typematic Delay Msec When the speed setting for the key input is enabled you can specify the interval of waiting time for the continuous key input Gate A20 Option Normal Fast tu Move ENTER Accept ESC Abort Typematic Rate Setting Disabled a Enabled t4 Move ENTER Accept ESC Abort Typematic Rate Chars Sec 6 1 1 Move ENTER Accept ESC Abort 90 CONTEC PT E831H PT E831HS User s manual 8 BIOS Setup Security Option Select whether the password is required every time the Security Option system boots or only when you enter setup If you have set a password select whether the password is required every time the System boots or only when you enter Setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt 1 Move ENTER Accept ESC Abort Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt Note To disable se
22. in this Manual Abbreviation Generic Abbreviation Generic Term OS Operating system Hard disk Hard disk drive 3 3 PT E Models Classify PT E831 models according to I F loaded on the PT E and the display features of the PT E Models of PT E831 series is shown in table 1 2 Table 1 2 PT E Models XGA W1024 x H768 dots Standard I F PT E831H Special I F PT E831HS For the LCD resolution there are about two dots upper and lower right and left are masked by the protective sheet Therefore please set the screen size in consideration of the masked range when creating a screen Standard Ethernet USB RS232C WDT RS485 RS422 Special I F SSCNET Standard I F CONTEC PT E831H PT E831HS User s manual 1 1 Introduction Features Correspond to USB I F Correspond to USB2 0 standard Resume Function By equipping a lithium ion battery pack option PT E can keep operating regardless of the occurrence of instantaneous interruption or power failure andprotect the data If battery voltage drop is detected or the power does not restore after power failure PT E will go to shutdown automatically When using resume function needs to start up EPC System Monitor refer to p 63 of Chapter 7 CF card Adopt CF card as a storage disk which is possible to build a system without hard disk it secures high reliability to the vibration and impact shock under the factory environment Ease of operation
23. is equipped with 1 port for SSCNET Table 4 10 SSCNET Connector 7654321 14131211109 8 CONTEC 32 PT E831H PT E831HS User s manual 5 Startup and Termination 5 Startup and Termination A CAUTION If switch power off or execute reset operation right after writing data always do it after exiting windows correctly Not doing so may break the data that have been written into the CF card sometimes it may get PT E not to start up normally Use same series CF cards in SLAVE and MASTER sides Any capacity is acceptable CF card supplied by our company is recommended Do not copy OS data by Explorer Doing so may get PT E not to start up normally Before Setup When PT E is started for the first time Windows Setup OS or Drivers installation etc might be necessary Table 5 1 Windows Setup Boot up Disk Drive E A i Whether OS is Preinstalled or Not Windows Setup Configuration Boot PT Ewith a CF card Windows XP Embedded is already preinstalled Option that is built in PT E OS is not installed Windows setup is required Boot PT E with an external HDD OS is not installed Windows setup is required 1 Ifyou ordered a CF card option in which Windows XP Embedded has been preinstalled you may use PT E without setting up Windows If you order a CF card in which Windows XP Embedded is not installed you need to setup Windows 2 Incase of using an external HDD as the boot up disk
24. latest event is displayed at top line Display EPC System Monitor s Set UP screen Refer to 19 Set UP button 4 None p 68 for details Product Information Display EPC system monitor s product information and 20 None button copy right information 1 PT A6BAT is a battery for saving PT E s time data and BIOS information 2 PT E73BAT is a lithium ion battery pack for using resume function 3 Dotted line region is masked if set Not use in the area of Resume function 4 ENC BAT is encoder battery of servo amplifier that is connected to PT E CONTEC PT E831H PT E831HS User s manual 67 7 Resume Function EPC System Monitor Set UP Screen Click button Set UP that is at the bottom of Start screen EPC System Monitor s Set UP Screen is displayed There is Power setting and Other setting in Set UP screen 1 Power setting Set necessary items for power management The following shows power setting screen a 2 aniet Operation Mode AR Method EPC System Monitor Set UP ER Power Zib Other ARUNA Standby C iezii Continue G RRE Timer Set 10 min GRANA t F Standby mode 0 30 min CESTA E N Continue mode 0 10 min C oF BE Battery Voltage LV AREAS Shalt EPSBATEESL TAL lo Please equip battery pack when using resume function GARDEIRI Windows HBEL NLE TO Windows will be restart when selecting Apply 6 0 8 Figure
25. minutes Standby state is released when power restoring and operation is restarted immediately from the state right before power failure Require the battery pack PT E73BAT Optional if use resume function ON OFF Switch POWER SW POWER SW is provided CONTEC PT E831H PT E831HS User s manual 23 4 Each Component Function CF Card Slot The CF card Type I II can be connected The built in disk drive has primary master drive and primary slave drive An CAUTION Do not use the CF card after removing it from PT E Doing so might cause trouble such as corrupt the files in the CF card due to improper using method Mountting a CF card 1 Remove the two screws on the back of PT E and remove the cover Built in disk drivers 5 EN Figure 4 10 Remove the cover 2 Confirm the up down sides and orientation of the CF card and insert the CF card far enough into the built in disk drive Up to two pieces of disks can be mounted CAR A Sa F P p CF Card Primary slave Liquid crystal panel side Primary master PT E back side Figure 4 11 Mounting a CF card An CAUTION The drive near the backside of PT E is the primary master drive the drive near the LCD panel side is the primary slave drive O CONTEC 24 PT E831H PT E831HS User s manual 4 Each Component Function Removing a CF card 1 Press the eject button of
26. s manual 5 1 Introduction Itis a characteristic of analog touch panels that their resistance may vary with changes to the ambient environment temperature and humidity and with their own aging resulting in the deviation of the detection point If this is the case calibrate the touch panel again to re set calibration data LCD may have a few bright spots that are always on or a few black spots that are always off Color irregularity may also occur depending on the viewing angle This however is due to the structural characteristics of the LCD therefore it is not a product fault Burn in on TFT Display Burn in may occur if the same display is retained for a long time Avoid this by periodically switching the display so that the same display is not maintained for a long time Burn In Phenomenon characterized by a TFT display as a result of long time display of the same screen where a shadow like trace persists because electric charge remains in the LCD element even after the patterns are changed The CF card connector doesn t support hot plug The pulling out opening of the CF card cannot be done in the state of power supply ON Please neither pulling out opening of CF in the state of power supply ON of this product nor come in contact with CF This product may malfunction or cause a failure Do not put the PT E on any object Doing so can cause a failure Do not touch the conductive areas and electronic parts of the PT
27. supports In Auto mode the system automatically determines the best mode for the device IDE Primary Master Slave UDMA UDMA Ultra DMA is a DMA data transfer protocol that utilizes ATA commands and the ATA bus to allow DMA commands to transfer data at a maximum burst rate of 33 MB s When you select Auto in the two IDE UDMA fields the system automatically determines the optimal data transfer rate for each IDE device IDE Primary Master PIO Auto Mode Mode Mode Mode Mode Move ENTER Accept ESC Abort IDE Primary Slave PIO Auto Mode Mode Mode Mode Mode ti Move ENTER Accept ESC Abort IDE Primary Slave UDMA Disabled Move ENTER Accept ESC Abort 98 CONTEC PT E831H PT E831HS User s manual 8 BIOS Setup On Chip Serial ATA setting Table 8 10 On Chip Serial ATA setting Selection OnChip Serial ATA Disabled Enabled On Chip Serial ATA Disabled Not use serial ATA Enabled Use serial ATA External IDE Device is recognized as SATA1 ti Move ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 99 8 BIOS Setup Onboard Device Phoenix AwardBIOS CMOS Setup Utility Onboard Device USB 2 0 Controller Enabled USB Keyboard Support Enabled Menu Level gt gt Azalia AC97 Audio Select ALL Disabled Il gt Move Enter Select PU PD Value F10 Save ESC Exit
28. test window is displayed with grids Press Close button to back to the test window Figure 6 9 Test window Grid view 2 Clear Press Clear button to clear the line and characters that are drawn or written when testing 3 Close Press Close button to exit test window CONTEC PT E831H PT E831HS User s manual 47 6 Setting the Touch panel Driver Mouse Operation 1 Click and drag operation Touch panel does the basic operations including click mouse double click and drag etc as follows Click Double click Drag 2 Right click Touch the screen and lift off Touch the screen twice quickly Touch the title bar of Window or icon with a finger or a touch pen and move the finger or the touch pen while touching There is no left right button on touch panel like a mouse use Event selector enable the right click operation by touch panel Do this operation as follows 1 Click Start on taskbar Move the cursor to All Programs P UPDD and click Event selector All Programs fan ScreenWorks gt Start Administrator Accessories T Startup G UPDD Internet Explorer 5 Outlook Express Settings E Shortcut to Startup El Test puter Click here Log Off o Turn Off Computer Figure 6 10 Event Selector button 48 CONTEC PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 2 Mouse window is displayed
29. the drive from where the CF card will be removed The eject button pops out t CF Card Ra Eject button Figure 4 12 Eject button 2 Push in the eject button Push in the eject button and push out the CF card halfway Pull and remove the CF card gently with your hand _ CF Card Eject button Figure 4 13 Removing a CF card CONTEC PT E831H PT E831HS User s manual 25 4 Each Component Function Giga bit Ethernet LAN 1 2 This product is equipped with 2 ports for giga bit Network type 1000BASE T 100BASE TX 10BASE T Transmission speed 1000M 100M 10M bps Max network path length 100 m segment Controller Marvell 88E8053 Table 4 3 Giga bit Ethernet Connector 100BASE TX 1000BASE T TRD 0 TRD 0 Cm LED LEDs for display of network statuses Left LED Link LED Green ON Operation Green Blinking Right LED Operation LED 10M Off 100M Green 1000M Red LAN drivers Install the appropriate LAN driver for your OS from the CONTEC s Web site IPC SLIB 01 For information on the latest version of IPC SLIB 01 check the CONTEC s web site A CAUTION When using both 2 ch Ethernets in 1000 BASE T please use PT E under the environment where the operating ambient temperature is Front display section is 0 C to 40 C other than display section is 0 C to 45 C CONTEC 26 PT E831H PT E831HS User s manual 4 Each Component
30. with a soft cloth dampened with either water or mild detergent Do not use chemicals or a volatile solvent such as benzene or thinner to prevent pealing or discoloration of the paint This product s case may become hot To avoid being burned do not touch that section while this product is in operation or immediately after turning off the power Avoid installation in a location where people may come into contact with that section CONTEC does not provide any guarantee for the integrity of data on CF Always disconnect the power cable from the receptacle before mounting or removing the expansion board or before connecting or disconnecting any connector To prevent corruption of files always shutdown the OS before turning off this product CONTEC reserves the right to refuse to service a product modified by the user In the event of failure or abnormality foul smells or excessive heat generation unplug the power cord immediately and contact your retailer To connect with peripherals use a grounded shielded cable Do not use any sharp pointed object such as a mechanical pencil to touch the touch panel Doing so may scratch the touch panel resulting in malfunctions Do not subject the touch panel to shock as doing so may break it When the surface or frame of the touch panel has become dirty wipe it with neutral detergent Do not wipe the touch panel with thinner alcohol ammonia or a strong chlorinated solvent PT E831H PT E831HS User
31. with touch panel Mouse simulation realized high resolution touch panel resolution 1024 x 1024 implements an excellent man machine interface to perform operations without a mouse and a keyboard Dustproof drip proof structure Front panel of PT E series is IP65F equivalent for worry free use in the environment of dust mist etc User should take measures against dust and mist for the other sections of PT E series e g by putting PT E in a self made box Improved vibration resistance and shock resistance Without structurally movable parts PT E series are resistant to vibration and shock requiring no special anti vibration measures and handling precautions Compact size PT E series fan less structure makes PT E get a compact size It is easy to build PT E in the equipment Supported OS Windows XP Professional Windows XP Embedded CONTEC 2 PT E831H PT E831HS User s manual 1 Introduction Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably Web Site Japanese http www contec co jp English http www contec com Chinese http www contec com cn Latest product information CONTEC provides up to date information on products CONTEC also provides product manuals and various technical documents in the PDF Free download You can download updated driver software and differential files as well as sample programs available in sever
32. 01 5 Operating Time H 6 System Information EPC System Monitor 1Sec counter 7 System information CONTEC 72 PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor Start Quit of EPC System Monitor EPC System Monitor implements power management therefore EPC SystemMonitor s Start Quit synchronizes with Windows OS 1 Start EPC System Monitor Make a setting to start EPC System Monitor while starting Windows For example register the shortcut of executable file Epcutil exe of EPC System Monitor to Startup Moreover set the following start option if necessary There are two kinds of setting methods specify file save destination drive and do setting with 1 Specify file save destination drive Table 7 7 Specify File Save Destination Drive Description Specify file save destination drive Specify file save destination drive for saving the following files 1st that are output by EPC System monitor Epcutil exe D argument Bg i y J di System setting information file epcutil log Alarm state file UPCUtl inf event history file EpcutilLog txt 2 Do setting with The following shows EPC System Monitor s start option list Start option setting example Epcutil exe Dd EPCSys _ B100_ W100 Table 7 8 EPC System Monitor s start option list Resume fu
33. 18 PT E831H PT E831HS User s manual System Configuration PT E831H PT E831HS CF card Front Interface Unit CF OGP B Optional PT E73FRU Optional Mouse USB compatible Commercially available Nae Panel Computer E Series Keyboard USB compatible Commercially available PT E3831H PT E831HS E y ci CD ROM Drive Unit USB compatible Battery Pack Commercially available PT E73BAT Figure 4 2 System Configuration CONTEC 4 Each Component Function FDD Unit USB compatible i Commercially available SSCNET Connector Motion Controller LAN Controller Commercially available PT E831H PT E831HS User s manual 19 4 Each Component Function Component Function Operation State LED Operation state LEDs are loaded on PT E PT E s operation state LEDs light on off as the operation state changing Therefore PT E s operation state can be confirmed by the operation state LEDs Operation state LED Figure 4 3 Operation State LED Table 4 2 LED display color Operation state of PT E LED di
34. 7 Parts Identification system CO cdo 19 Comip nent FUNCHON ssie aae i ERRES AENEAS STOTE NASAle 20 Operation State LED nnen rE E E EE E EE ER 20 AC Power Input Connector ACIN usais 21 ON OFF Switchs POWER SW oriee a E A NE EE AER EN 23 CE Card Slota Giga bit Ethernet CONTEC PT E831H PT E831HS User s manual 111 LOSTE osa A O ke o ARETE ti otk EN ar ee oy oh Sse CANN Oa eae ae ee eg D1 SerialPort Interface COM2 35 aaa AA GA ERA EAE eels 27 WDIT EMG Connettore sas 30 IDE on yy s E a T E E E A AE EOE ee 31 PE Power Supply O OEO OA a a 31 PELBus Expansion Slotsins ess aera ahaa EE ATES AEEA E EN A RER 31 SSCNET Connectoren id esas LEELEE STEES AEE LEE iS E ETEN 32 5 STARTUP AND TERMINATION 33 Bd A e cn 33 Wrlite protcCb ainia datan litera 34 POR Se 39 6 SETTING THE TOUCH PANEL DRIVER 41 Calibration Settings sisas ia ena eiss stan 41 MI A cable E E E 46 Mouse Operation tie 48 Function of Touch Panel Drivers aria ta 49 7 RESUME FUNCTION EPC SYSTEM MONITOR 63 Resuine FC Nara 63 EPC Systemi Monttor cesinasosttida patios lib itia acta 64 8 BIOS SETUP 11 A A aa 77 Startins DU as 77 Using Setup Getting Help 78 In Case of Problems 78 A Final Not About Setup seess nenesie iii 78 Maim Mi aii 79 SAUS A AR A A AAA TEE O R 79 Standa CMO T Setup id 81 Main Menu Selections za enirn ainia 82 Onboard PATA Master Onboard PATA Slave ccccscssessesesseseseesee
35. 7 2 Power Setting screen 68 CONTEC PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor 2 Other setting Set items other than power The following shows other setting screen EPC System Monitor Set UP TF Power EK Other WDT RE FFA U 255 5 25 3 WOT Setting E se Mo SEA C RIRH No Use 4 O PIARES MUERTA Main Screen is displayed when alarm occurring 5 M smeta Window is minimized when starting 6 7 8 Figure 7 2 Other setting screen The following shows details about Item button on Set UP screen Table 7 2 Set UP Screen Item Button Set operation mode Standby or Continue of resume function refer 1 Operation Mode to p 63 for resume function This item is available when setting USE for Resume Function 1 Set method of resume function a Timer Set or Battery Voltage can be chosen b In case of choosing Timer Set please do time setting 2 Method A 7 c Even in method of Timer Set if low battery voltage is detected before passing the setting time system will go to shutdown d This item is available when setting USE for Resume Function Set time to output error If reset operation is not done after passing 3 WDT 2 Setting the setting time WDT error signal is output Main Screen is we N i If choose this item EPC System Monitor s start screen refer to p 4 displayed when i 4 e
36. CMD EXE lol x Confirm this item DE 00 00 00 00 00 00 00 00 00 YHa Figure 5 8 The item of State and the item of Boot Command 3 Quit command prompt Not require to restart PT E CONTEC 38 PT E831H PT E831HS User s manual 5 Startup and Termination Power OFF This section explains how to power off PT E To switch power off always quit Windows correctly following the next procedures and switch off the power supplied to PT E 1 Save data and exit all applications 2 Choose Turn Off Computer from Start menu Administrator ws My Computer Control Panel IT Run AllPrograms gt Click here Figure 5 9 Turn Off Computer button 3 The window of Turn off computer is displayed Choose Turn Off to switch off the power Turn off computer Stand By Figure 5 10 The window of Turn off computer 4 After quitting the system switch the power supplied to PT E main body CONTEC PT E831H PT E831HS User s manual 39 5 Startup and Termination Point 0 2 3 4 In case of using a CF card executing write protect to the CF card may reduce access number of times to the CF card and it also may reduce risk that corrupts data in the area where write protect has been executed In case of not using resume function if turns on the power right after switching off please wait more than 10 seconds before switching it on again In case of using re
37. Defaults F7 Optimized Defaults Figure 8 6 Hard Disk Boot Priority Details screen is displayed when selecting the item of Hard Disk Boot Priority on the screen of Advanced BIOS Features Table 8 5 Hard Disk Boot Priority CHO M Set the connected HD Bootable Add in Cards Set start priority order of connecting HD CONTEC PT E831H PT E831HS User s manual 87 8 BIOS Setup Table 8 6 Advance BIOS Feature Selections CPU Li amp L2 Cache Disabled CPU L1 L2 Cache Enabled These allow you to enable speed up memory access or disable the cache function Ni Move ENTER Accept ESC Abort Quick Power On Self Test Dis abled Enabled Quick Power On Self Test Select Enabled to reduce the amount of time required to run the power on self test POST A quick POST skips certain steps We recommend that you normally disable quick POST Better to find a problem during POST than lose data during your work t Move ENTER Accept ESC Abort Third Boot Device 15120 Hard Disk First Boot Device CDROM ZIP100 The BIOS attempts to load the operating system from the USBFDD devices in the sequence selected in these items USB ZIP USB CDROM LAN Disabled t4 Move ENTER Accept ESC Abort CONTEC 88 PT E831H PT E831HS User s manual Second Boot Device The BIOS attempts to load the operating system from the devices in the sequence selected in
38. EEPROM Calibration Cancel Apply Help Remove the checking Figure 6 2 Pointer Device Properties Calibrate Test When changed settings always click Apply A button to make the changed settings available Clicking Apply A button makes the controller initialization which may make touch panel not react for several seconds 42 CONTEC PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 3 Calibration window is displayed R they appear Figure 6 3 Calibration screen Press K in order and make settings The method of setting is as follows 1 Press the tip of K with a touch pen 2 Lift the touch pen off screen 3 After lifting the touch pen off the screen a beep sounds and K appears in the next position Similarly set the position where is indicated by Perform this operation for all numbers of points that have been set at point number in Calibration Setting window Ifthe screen is not touched for the time that has been set in the calibration settings calibration window will be closed and calibration is aborted Do calibration setting again CONTEC PT E831H PT E831HS User s manual 43 6 Setting the Touch panel Driver 4 When all calibration points settings are completed a dialog box for calibration confirmation is displayed If no problem occurs on any calibration point clicks OK to finish the calibration If make
39. EpcUtilLog txt and epcutil log to the new CF card Not doing so the operating time will be reset 2 Please set optional settings in the setting range 3 During EPC System Monitor working do not remove the drive where has been specified by option setting as file save folder Doing so may cause file writing error CONTEC PT E831H PT E831HS User s manual 75 7 Resume Function EPC System Monitor CONTEC 76 PT E831H PT E831HS User s manual 8 BIOS Setup 8 BIOS Setup Introduction This chapter discusses Award s Setup program built into the FLASH ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is turned off The rest of this chapter is intended to guide you through the process of configuring your system using Setup Starting Setup The Award BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system While the BIOS is in control the Setup program can be activated in one of two ways 1 By pressing lt Del gt immediately after switching the system on or 2 By pressing the lt Del gt key
40. Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 10 Onboard Device Table 8 11 On board device Selections USB Controller Enabled Disabled USB Controller Enable or disable the USB Over Current In normal cases set it as Enabled ti Move ENTER Accept ESC Abort USB 2 0 Controller Enabled USB 2 0 Controller Disabled Enable or disable the Onboard USB 2 0 function In normal cases use it while Enable ti Move ENTER Accept ESC Abort CONTEC 100 PT E831H PT E831HS User s manual 8 BIOS Setup USB Keyboard Support Disabled Select Enabled when a USB keyboard has to be used on Enabled the OS that does not support USB USB Keyboard Support Select Disabled for the OS that supports USB such as Windows XP t Move ENTER Accept ESC Abort Azalia AC97 Audio Select AC97 Audio only All Disable Azalia AC97 Audio Select Set audio function tMove ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 101 8 BIOS Setup Super IO Device Phoenix AwardBlOS CMOS Setup Utility SuperlO Device Enabled Enabled Onboard Serial Port 2 Onboard Serial Port 3 Item Help Menu Level gt voc Move Enter Select PU PD Value F10 Save F6 Fail Safe Defaults
41. Function USB Port USB This product is equipped with 4 ports for USB 2 0 interface Table 4 4 USB Connector Function ae o AC IC paar aac Serial Port Interface COM2 3 Serial Port COM2 RS232C This product has a serial port that corresponds to RS232C Pin No Table 4 5 Serial Port Connector COM2 Connector used D sub9 pin male on the product ee INICIO INSI ION AR CONTEC PT E831H PT E831HS User s manual 27 4 Each Component Function Serial Port COM3 RS232C RS422 RS485 This product has a serial port that corresponds to the communication modes RS232C RS422 and RS485 You may set communication mode of serial port COM3 by setting switches in PT E Table 4 6 Serial Port Connector COM3 Connector used D sub9 pin male on the product 7 Function Pin No Switching Serial Port COM3 among RS232C RS422 and RS485 The serial port COM2 corresponds to RS232C COM3 corresponds to the communication modes RS232C RS422 and RS485 Using the serial communication mode setting switches No 1 to No 7 you can set communication mode for serial port COM3 The setting method is as follows 1 Remove the two screws on the back of PT E and remove the cover Built in disk drivers Figure 4 14 Remove the cover CONTEC 28 PT E831H PT E831HS User s manual 4 Each Component Function 2 According to Table 4 7 set the co
42. IPC Series PANEL PC E Series PT E831H PT E831HS User s Manual CONTEC CO LTD Check Your Package Thank you for purchasing the CONTEC product The product consists of the items listed below Check with the following list that your package is complete If you discover damaged or missing items contact your retailer If you use IPC SLIB 01 driver amp utility software set download it from the CONTEC s Web site Product Configuration List PT E831H AC431x PT E831HS AC431x Basic Typel Multi Interface Type The attachment fittings PT E71I MOUNT 1 set a S 8 pcs Face protective seal PT E82PSC Attached Panel PC Holding battery for BIOS Attached Panel PC Product guide this sheet PC Precaution List Recovery Media 1 Please confirm latest information on the CONTEC homepage though the user s manual is stored in Recovery Media The installation method is described in this document as well as the UsersManual File storing place Manuall Product Configuration Image T gt Product IPC guide Precaution List Panel PC The attachment Product guide IPC fittings Precaution List Royalty consent contract Royalty Recovery Media consent contract See the Product Configuration List to check if all the components are included for the specified number of units CONTEC PT E831H PT E831HS User s manual i Copyright
43. OM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result tJ Move ENTER Accept ESC Abort Video BIOS Cacheable Video BIOS Cacheable Disabled Enabled Selecting Enabled allows caching of the video BIOS ROM at C0000h C7FFFh resulting in better video performance However if any program writes to this memory area a system error may result ty WMove ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 93 8 BIOS Setup VGA Setting The field under the On Chip VGA Setting and their defaults settings are Table 8 8 VGA setting Selections PEG OnChip VGA Control PEG Onchip VGA Control OnChip VGA Onchip VGA Enable Onchip VGA PEG Port Enable PCI Express Graphic Auto Enable graphic controller automatically ti Move ENTER Accept ESC Abort OnChip Frame Buffer Size On Chip Frame Buffer Size When Enabled a fixed VGA frame buffer from A000h to BFFFh and a CPU to PCI write buffer are implemented tJ Move ENTER Accept ESC Abort DVMT Mode FIXED DVMT Mode DVMT BOTH Allows you to set the Dynamic Video Memory Technology DVMT mode 1 Move ENTER Accept ESC Abort CONTEC 94 PT E831H PT E831HS User s manual 8 BIOS Setup DVMT FIXED Memory Size 64MB a i DVMT FIXED Memory Size 128M9 sees
44. ON Ground lightening surge absorber EA and PT E s power cable earth wire EB separately Select the lightening surge absorber that not exceeds the maximum permissible circuit voltage of the sure absorber at the maximum power supply voltage CONTEC 22 PT E831H PT E831HS User s manual 4 Each Component Function 2 Grounding a Where possible ground the PT E independently The grounding work is class D grounding grounding resistance 100Q or less b When independent grounding is impossible use the joint grounding method marked 2 below PLE Other PTE Other PTE Other equipment equipment equipment Class D Class D grounding roundin 1 Separate ground connectio 2 Common ground connection 3 Common ground connection Option Acceptable Not permitted Figure 4 9 Grounding method c The size of grounding wires must be 2 mm or more Use wire in which green and yellow color is combined for grounding wire The grounding point should be as near as possible to PT E to minimize grounding cable length A CAUTION Do class D or higher grounding work to earth PT E In addition do not share the grounding with other equipment 3 Remark For PT E831 series if use resume function operation shifts to either mode below when power failure or voltage drop occurring 1 Continue mode Keep operating for 10 minutes 2 Standby mode Keep standby state for 30
45. Press Enter detection is successful it fills the remaining fields on this menu Set the CF Card specifications Normally specify Auto Onboard PATA Master E 3 Onboard PATA Slave When using an old CF Card that is not recognized by Auto setting Choose the access mode for this CF Card Auto Display your CF Disk drive capacity Approximated Note that this size is Capacity card tet q usually slightly greater than the size of a formatted disk given by a disk checking program The following options are selectable only if the IDE Channel 0 2 Master Slave item is set to Manual and CHS item is set to Manual A Min 0 a i Cylinder Max 65535 Set the number of cylinders for this CF card Head abn 0 Set the number of heads for this CF card Max 255 Min 0 Warning Precomp ME 65535 Setting a value of 65535 means no CF card CONTEC PT E831H PT E831HS User s manual 83 8 BIOS Setup i Min 0 E Max 65535 Bso a l Min 0 WES 955 Number of sectors per track CONTEC 84 PT E831H PT E831HS User s manual 8 BIOS Setup Onboard SATA 0 Onboard SATA 1 Phoenix AwardBIOS COMS Setup Utility Onboard SATA 0 IDE HDD Auto Detection Press Enter Extended IDE Drive Auto Menu Level gt gt Access Mode Auto To auto detect the Capacity 1024 MB HDD s size head on this channel Cylinder 1985 Head 16 Precomp 0 Landing Zone 1984 Sector 63 l gt e Move
46. Press the Default button to be the default setting Event This screen shows the pointer device events that can be generated by the device and the Button Modes mouse click actions associated with the events When an event occurs either the Primary or Secondary action will be performed depending on the Event Selector state To change the primary default the left button or secondary default the right button action also may use mouse window refer to section p 48 Pointer Device Properties a Devices Hardware Settings Advanced Events General Windows Calibration Status About Settings For 1 Primary Default Touchdown Left Bu Secondary 2 Defaults Calibrate Test Figure 6 21 Event tab 1 Primary Set mouse s primary action setting 2 Secondary Set mouse s secondary action setting 3 Defaults button Press Defaults button to return to the default setting CONTEC 58 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver Double click Used to make settings about double click Pointer Device Properties xl Devices Hardware Settings Advanced Events General Windows Calibration Status About Windows Settings Double Click Settings Mouse Click Test 1 gt Single Click Double Click 2 Time ERA i 500 Height A 50 Width Y 50 Defaults Calibrate Test Cancel Apply Help Figur
47. R button Reset the count values shown for the Com port error Overflow and Synchronize error 4 Re initialise Z button Re initialise the controller CONTEC 60 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver About Used to show version information support information and licence agreement of touch panel driver C Pointer Device Properties Devices Hardware Settings Advanced Events General Windows Calibration Status About 1 gt Universal Pointer Device Driver Company DMC Co Ltd Driver program version 03 08 50P Copyright Touch Base Ltd Build 03 08 50P 0865 G2459 ES DMC Co Ltd Interface with Touch Licence Calibrate Test Figure 6 24 About tab 1 Touch Panel Driver Show the version information of the controller to be used 2 Support P button Show the support information 3 License L button Show Licence agreement information of touch panel driver CONTEC PT E831H PT E831HS User s manual 61 6 Setting the Touch panel Driver CONTEC 62 PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor 7 Resume Function EPC System Monitor Resume Function Resume function can keep PT E operating regardless of the occurrence of instantaneous interruption or power failure and protect data by equipping a lithium ion battery pack option on PT E With EPC System Monitor it is possi
48. Setup If set to Setup prompting only occurs when trying to enter Setup CONTEC 108 PT E831H PT E831HS User s manual 8 BIOS Setup Exit Selecting Save amp Exit Setup Pressing lt Enter gt on this item asks for confirmation Save to CMOS and EXIT Y N Y Pressing Y stores the selections made in the menus in CMOS a special section of memory that stays on after you turn your system off The next time you boot your computer the BIOS configures your system according to the Setup selections stored in CMOS After saving the values the system is restarted again Exit Without Saving Pressing lt Enter gt on this item asks for confirmation Quit without saving Y N Y This allows you to exit Setup without storing in CMOS any change The previous selections remain in effect This exits the Setup utility and restarts your computer CONTEC PT E831H PT E831HS User s manual 109 8 BIOS Setup CONTEC 110 PT E831H PT E831HS User s manual 9 Appendix 9 Appendix Battery Specification This product uses the following battery Name PT A6BAT Type Lithium primary battery Model ER 17 33 Maker Maxell Nominal voltage 3 6V Nominal capacity 1600mAh Lithium content 0 5g Battery PT A6BAT exchange method 1 Switch off the power supplied to PT E In case of using a resume battery remove it 2 Remove two screws on the back of PT E and then remove the cover
49. Temperature ae E s mite Low 4 CPU FIA CPU Temperature o 42 Z Operating Time 1 2 USBta 2 8h PVE ii i o USB Fuse Blown Y Condenser IAEA oca 9 13 FR SIRF Bl Entero _ 2 Eme Forecast 14 FEEF ATA Low Voltage Exchange Forecast s 649 1 5 IEA a Count o 0 count 1 1 6 PRED KEP BRT FEME FASEB th l e Charging Charge end Charge prohibit Charge circuit reset l Sa O O O O o I SS St al Se Exchange Forecast 1586 1 7 18 19 20 Figure 7 1 Monitor Screen Start screen The following shows details about Item button on Set UP screen Table 7 1 Monitor Screen Item Button Description Lamp Color Item Button Description Normal Alarm Error When detecting an alarm the corresponding alarm message is displayed When more than one alarm occurring messages are Alarm None switch displayed every 5 seconds Confirm occurring time and detected data etc on Event LOG screen Display internal board temperature 2 System Temperature r Green Red Give an alarm when system temperature is over 100 C Display CPU internal temperature 3 CPU Temperature i Green Red Give an alarm when CPU temperature is over 100 C Display operating time current time from starting PT E 4 Operating Time E 7 pi E None the first time Detect USB 1 to 4 fuse blowout and display current state 5 USB fuse blown f Green Red Give an alarm when detecting USB fuse blowout i Displ
50. a in the windows When using EEPROM calibration the position position of the arrow of the calibration point becomes a fixation About calibration setting method refer to following Save to Windows Refer to p 41 Save to EEPROM Refer to p 44 Calibration Pattern Show the calibration point pattern to be set in 3 and 5 Used to confirm the number of points and point position that have been set in 3 and 5 PT E831H PT E831HS User s manual 53 6 Setting the Touch panel Driver Devices Used to add modify and delete controllers El Pointer Device Properties xl Devices Hardware Settings Advanced Events General Windows Calibration Status About The following devices are installed device segment Priority id Port Controller 0l Device 1 Whole Desktop __Interlock COM1 DMC TSC 10 Series 2 Modify 3 Remove lt 4 Calibrate Test OK Cancel Apply Help Figure 6 17 Devices tab 1 Device list Show the information of the controller to be used 2 Add D button Add a controller 3 Modify M button Change name or operation object of controller 4 Remove R button Delete a controller CONTEC 54 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver Hardware Used to set touch panel driver s communication setting Pointer Device Properties xi Devices Hardware Settings Advanced
51. a mistake in point except the calibration points doing nothing but waiting 10 seconds After 10 seconds passed the calibration data are canceled and they are not saved in the Windows Check calibration x Touch the OK button below to check calibration If no touch is received within 10 seconds the crigna settings will be restored Figure 6 4 Check calibration window Calibration Settings When Using EEPROM Calibration Calibration setting that uses EEPROM calibration saves the calibration data in EEPROM within PT E Because the calibration data are saved in EEPROM the calibration setting condition is identical for the same PT E Don t need to do calibration again even though exchange start up disk 1 Click Start on taskbar Move the cursor to All Programs P UPDD and click Operation Setting Administrator M Accessories f Startup 8 Internet Explorer 3 Outlook Express amp Shortcut to Start UP All Programs fam ScreenWorks Log Off o Turn OFF Computer Click here Start Figure 6 5 Settings button CONTEC 44 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 2 Touch Panel Driver Properties window is displayed Click Calibration N tab and check EEPROM Calibration Make calibration setting according to need Refer to p 52 Click Apply A button when change the settings so that the changed settings are available After completing
52. ailable Windows XP package PT E s specified drivers touch panel driver display driver and etc and EPC System Monitor are necessary Call our sales offices please EPC System Monitor Function EPC System Monitor has the following functions a 2 6 4 65 6 PT E s power supply management Control operation when power failure occurring refer to p 62 for Resume function and going to shutdown Hardware state monitor Monitors operating time system temperature CPU temperature battery state and control voltage etc WDT Watch Dog Timer function After starting EPC System Monitor Windows application regularly executes WDT reset if reset operation is not executed after passing the setting time system is regarded as abnormality and WDT error signal is output Alarm detection Detect alarm of system temperature CPU temperature battery state and control voltage power supply voltage for internal circuit etc Event log Output hardware monitor state change or occurred alarm information to a history file State output PT E main body hardware s monitor state or alarm information can be used by other applications CONTEC 64 PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor Monitor Screen Start screen ie EPC System Monitor 2 Clicking button EY can gt not close the screen Alarm fuste 2useD use Fuse Blown USB2 10 VATA Ji System
53. al languages Note For product information Contact your retailer if you have any technical question about a CONTEC product or need its price delivery time or estimate information Limited One Year Warranty CONTEC products are warranted by CONTEC CO LTD to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office from which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original products The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization number RMA from the CONTEC group office where you purchased before returning any product No product will be accepted by CONTEC group without the RMA number Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incid
54. an and the global environment Please refer to the user s manual for the annulment of detaching a detailed battery specification and the battery and the batteries Trademarks Intel Intel Atom Intel Core and Celeron are registered trademarks of Intel Corporation MS Microsoft and Windows are trademarks of Microsoft Corporation Other brand and product names are trademarks of their respective holder CONTEC ii PT E831H PT E831HS User s manual Table of Contents Check Your Package ori TA Aaa i CI a2 ss cheeses ea Aad ie aS Ah RU E a gh ag ii About the handling of the battery and the storage battery in EU eee eee es eseeeeeeeeeseseeeeneeees ii ON NON ii Trad eMark SS von wes e O o ed ii Table of Contents aoan Aaa iii 1 INTRODUCTION 1 ABOut the Product rsidia citando E eases ste 1 PEE Models scott 1 Features ssc oses O RN 2 Supported OS o issn a E A RE T R E R TE R E 2 CUSLOMET SUPPORT A N AOE A INER 3 Web Sitenka nanan A E strane R atlantica 3 Limited One Year Warranty aaa 3 How to Obtain e 3 A O TONER AN 3 Safety Precautions A eve uee tere Me Ghana 4 Safety Information 4 Caution On the AA veiastss AEE EN I EE SAET IESS 4 2 SYSTEM REFERENCE 7 PEC A 7 Physical DIAS es ero e eo ad ad 10 3 HARDWARE SETUP 1 1 1 Before Using the Product for the First Time will Hardware Setups iiaea n e 12 How to Mount eed ND Installation Requirements Ai 1 4 4 EACH COMPONENT FUNCTION 17 1
55. ay The expected brightness through a touch panel is about 80 lower than the above value Contrast ratio CR Brightness at screen center with white displayed Brightness at screen center with black displayed Z Measurement direction T Bees G 180 Module Right be 90 Y Figure 2 1 Definition of viewable range A CAUTION The above optical specification data shows optical characteristics of the liquid crystal in the display the data does not represent the actual view on the display or its viewing angles CONTEC PT E831H PT E831HS User s manual 9 2 System Reference Physical Dimensions PT E831H PT E831HS en a a a ab 0 0 008 0 0 40 gt a a 4 q x A c_ E ES 10 E e 5 q Y JE di s _vY_ 22 12 SS 45 28 395 e te 85 Unit mm Figure 2 2 Physical Dimensions CONTEC 10 PT E831H PT E831HS User s manual 3 Hardware Setup 3 Hardware Setup Before Using the Product for the First Time Follow the next steps to set up this product STEP1 By referring to the information in this chapter install connect and set this product STEP2 Connect cables Connect the cable of necessary external devices such as keyboard
56. ay forecast result of condenser longevity based on Condenser Longevity 4 6 F i Operating Time and System Temperature Give an alarm Green Red orecas when forecast result is over 98 CONTEC PT E831H PT E831HS User s manual 65 7 Resume Function EPC System Monitor Lamp Color No Item Button Description Normal Alarm Error Low Check low voltage signal of PT A6BAT and display the G reen T AGBAT Voltage current state Exchange A Give an alarm when low voltage is detected Green Re Forecast Check low voltage signal of PT E73BAT and display the OW current state Give an alarm if PT E73BAT is not loaded Green Re Voltage on Exchange Display forecast result of PT E73BAT longevity Give an j Green Re Forecast _ alarm when forecast result is over 98 Charge Display charge discharge count number Give an alarm Discharge when charge discharge count number is over 300 times Green Re Count since started the first time Charging Light during charging normally Orange Blinking Charge A e F Light when charge is over normally Green None en 3 EP73BAT Light when PT E73BAT can not be charged due to the Charge ollowing causes Lamp color at moment of lighting Red Ns None Blinking prohibit 1 PT E73BAT is not loaded on 2 Adapter is abnormal Light at the moment of the following case Lamp color at moment of lighting Blue 1 PT E EPC System Mon
57. ble to choose Continue mode or Standby mode when power failure occurring and do time setting Moreover when battery voltage drop is detected or power supply is not restored after power failure PT E will go to shutdown automatically 1 Continue mode a When power failure is detected PT E keeps on operating but backlight becomes OFF In Continue mode screen operation is unavailable b If power supply restores before passing the setting time 0 to 10 minutes or power supply restores before detecting battery voltage drop backlight will become ON and operation goes on If power supply does not restore goes to shutdown 1 c If battery voltage drop is detected before passing setting time PT E goes to shutdown 1 1 You can set whether execute shutdown process or not Refer to p 73 2 Standby mode a When power failure is detected backlight becomes OFF PT E goes to standby state b If power supply restores before passing the setting time 0 to 30 minutes or power supply restores before detecting battery voltage drop standby state is released and PT E restarts operation from the state right before power failure If power supply does not restore PT E goes to shutdown c If battery voltage drop is detected before passing setting time PT E goes to shutdown Point 1 For using resume function you must equip a lithium ion battery pack with PT E 2 Before using resume function always fully charges the lithium i
58. ce Hardware Action Setting Advanced Setting Event Double Click States Information Calibration C button Make calibration settings 2 About calibration setting refer to p 41 3 Test T button Make a touch operation testing About testing refer to p 46 4 OK button Save the setting data and exit Touch Panel Driver Properties window CONTEC 50 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 5 Cancel button Cancel the setting data and exit Touch Panel Driver Properties window 6 Apply A button Make the changed settings available 7 Help button Show online help of touch panel driver General Used to set basic operations for touch panel El Pointer Device Properties x Devices Hardware Settings Advanced Events General Windows Calibration Status About l General Settings 1 T Show icons in system tray 2 Check calibration 3 Y Calibration Beeps 4 gt Clone 5 gt gt Dump settings Calibrate Test Cancel Apply Help Figure 6 14 General tab 1 Show icons in system tray Use this setting to enable or disable register the icon on the taskbar If show icons in system tray check the checkbox 2 Check calibration If set it a Calibration confirmation dialog box is displayed at the end of calibration 3 Calibration Beeps If set it sound is used to indicate a calibra
59. completed Confirm that the item of Boot Command becomes DISABLE WINDOWS SYSTEM32 CMD EXE E ioj xj Confirm this item 5F 46 OA O 00 00 00 00 00 00 00 00 00 00 Der j Figure 5 6 The item of Boot Command 4 Quit command prompt and then restart PT E 5 Write protect is released after restarting PT E CONTEC PT E831H PT E831HS User s manual 37 5 Startup and Termination Method of Confirming the State of Write protect This section describes how to confirm present state of CF card and how to confirm whether write protect already been executed or not 1 Click Start on taskbar Move the cursor to All programs P gt Accessories and click Command Prompt E Accessibility E Communications 7 Entertainment m System Tools L_ Calculator Click here Command Prompt Administrator D Notepad Y Paint J My Computer amp Windows Explorer Gm Accessories A WordPad m Startup E uoo Internet Explorer Figure 5 7 Command Prompt 2 Command prompt is started Input command ewfmgr C Show as follows after pressing Enter key Confirm the item of State State DISABLED The state that write protect is released ENABLED The state that write protect is executed When confirming the state of the CF card the item of Boot Command shows as NO_CMD executing releasing write protect cannot be switched INDOWS SYSTEM32
60. curity select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not type anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely Summary Screen Show Enable d Summary Screen Show Disabled Set whether or not to display configuration screen after BIOS starting N Move ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 91 8 BIOS Setup Advanced Chipset Features Setup Phoenix AwardBIOS COMS Setup Utility Advanced Chipset Features 3 3 Menu Level gt Enabled Disabled DRAM Timing Selectable CAS Latency Time DRAM RAS to CAS Delay System BIOS Cacheable Video BIOS Cacheable xx VGA Setting PEG Onchip VGA Control On Chip Frame buffer size DVMT Mode DVMT FIXED Memory Size Boot Display Panel Type Boot After SWON Move F5 Previous Values Enter Select PU PD Value F6 Fail Safe Defaults Onchip VGA 8MB DVMT 64MB CRT LVDS LVDS Non Boot F10 Save ESC Exit Fl General Help F7 Optimized Defaults Figure 8 7 Advanced Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset This chipset manages bus speeds and access to system memory resources such as DRAM and the external cache It must be stated that these items should never
61. dary master drive 3 o eremita USB connector 1 2 USB connector 3 4 LAN connector LAN comnector2 PCI bus expansion slot_ Reset button Watchdog timer can be set from 0 1sec to 25 5sec and the signal can be output 5 WDT EMG connector Moreover an emergency stop signal can be input SSCNET ti ieee Connect a SSCNET compatible device motion controller etc PT E831HS only RS 232C connector COM2 Connect a RS 232C compatible device RS 232C connector COMB can be switched among RS232C RS422 and RS485 COM3 USB connector 1 2 E A 7 Connect USB compatible devices such as keyboard mouse printer etc USB connector 3 4 LAN connector 1 3 Connect with network LAN connector 2 PCI bus expansion slot Connect an add on unit and use PCI bus expansion board Reset button Restart PT E Display PT E S operation status 7 eje A Red blinking During starting up shutting down or EPC System Monitor is not Operation status LED started Red EPC System Monitor starting up Green blinking Standby Power supply input E PPIP Connect power supply cable terminal i Lithium ion battery pack EP73BAT Battery pack Optional Do not need the battery pack if not use resume function Switch COM3 s communication mode among RS232C RS422 and RS485 Switch No 1 to No 7 ON OFF switch Switch power on off Upside ON downside OFF Setting switch 9 CONTEC
62. e 6 22 Double click tab 1 Double Click Settings a Time Change the time period within which windows will register two clicks as a double click b Height Specify the number of pixels vertically within which windows will recognize two clicks as a double click c Width Specify the number of pixels horizontally within which windows will recognize two clicks as a double click d Default button Press the Default button to return the default setting 2 Mouse Click Test Used to test single and double click responses which is set in section 1 You can click to test single or double click response When touching is recognized as a single or double click the icon changes from to to CONTEC PT E831H PT E831HS User s manual 59 6 Setting the Touch panel Driver Status Used to show the controller status along with system resource usage and to re initialize the controller El Pointer Device Properties Devices Hardware Settings Advanced Events General Windows Calibration Status About Pointer Devices Status _ device init state comms error overflows syncerrors 0 0 0 Pool usage Now HWM Reset Ju 2 IES Refresh Reinitialize 4 Calibrate Test Cancel Apply Help 3 Figure 6 23 Status tab 1 Status Show the status information of the controller 2 Reset X button Reset the default status 3 Refresh
63. e until the brightness is lowered to 50 of the initial value at atemperature of 25 C CONTEC 6 PT E831H PT E831HS User s manual 2 System Reference 2 System Reference Specification Table 2 1 Functional Specification lt 1 2 gt Model PT E831H PT E831HS Windows XP Embedded SP2 recommend Windows XP Professional OS Resume function Continue Standby mode can be selected when power failure is detected Continue mode System keeps operating for 10 minutes during the power failure Resume Function 1 Backlight becomesOFF Standby mode System keeps the standby status for 30 minutes Standby status is released as powersupply restoring and the system restarts operating immediately from the status right before power failure Battery pack Lithium ion battery pack EP73BAT Optional Not require the battery pack if not use resume function URED 2 ch D sub9pin male Serial Port 1 ch is compatible with RS232C 1 ch is allowed to switch among RS232C RS422 and RS485 Ethernet 10BASE T 100BASE TX 2 ch 4 1000BASE T External PCI bus expansion slot Expands PCI bus with an add on unit t Interface 2 slo 2 CF card slot CF Type I ID CF1 is finished mounting CF 1 GB 1 partition 5 SSCNET None th pi ea 1ch WDT EMG Watchdog Timer can be set from 0 1 sec to 25 5 sec and the signal can be output D sub9 pin female aa 1 For the model PT E831HS if it is usi
64. eeseeeeseeeseeeeseeseneeaeeeaeeeeaeeeeaeees 83 Onboard SATA 0 Onboard SATA 1 oe eceecscecseeseseeseseeseeeseeeseeeesceceaeeecseeecseeseaeeaeaeeaceeeaeeeeaeeeeaeees 85 Advanced BIOS Features Setup ii A AAA Sige 86 Hard Disk Boot PA oi 87 Advanced Chipset Features Setup oocicoconnnnnnnonnnnnnononanonncnonnnnnononnononnnnnnnnonononnnnn ron svatos teniseri veeres isa sees 92 VGA Seta oiata AE EEI 94 Integrated Peripherals iii as 96 OnChip IDE DICE iia cantares asa 97 On Chip Serial ATA SA done 99 Onboard Deidad it tie aiii 100 CONTEC lv PT E831H PT E831HS User s manual Super OMDevice reassess a a do 102 PnbP PCI Configuration Setup iia iii 103 RAR ads 105 PESAS oo A E E aia viene OE DAM a ia Supervisor User Password Setting EXIT O o e gee ele UREA e 9 APPENDIX 111 Battery Specification inayat ceca eras eae eh Se a sp ces a a yale Le ae ats 111 10 LIST OF OPTIONS 113 CONTEC PT E831H PT E831HS User s manual v CONTEC PT E831H PT E831HS User s manual 1 Introduction 1 Introduction About the Product This product is a fanless PANEL PC for embedded use based on Intel R Celeron M ULV processor Usable worry free in factory automation fields PT E is PC AT compatible controller for built in use it is compatible with Windows XP Windows XP Embedded Unless otherwise specified this manual uses the following abbreviations and generic terms to describe PT E Table 1 1 Abbreviation
65. en press Enter key WINDOWS SYSTEM32 CMD EXE loj xj 5 Figure 5 2 Executing command CONTEC 34 PT E831H PT E831HS User s manual 5 Startup and Termination 3 Show as follows as soon as the processing of write protect is completed Confirm that the item of Boot Command becomes ENABLE Confirm this item Figure 5 3 The item of Boot Command 4 Quit command prompt and then restart PT E 5 Write protect is executed after restarting PT E As for the method of confirming the state of write protect refer to next page CONTEC PT E831H PT E831HS User s manual 35 Sa Startup and Termination Method of Releasing Write protect This section describes how to release write protect 1 Click Start on taskbar Move the cursor to All programs P Accessories and click Command Prompt E Accessibility E Communications 7 Entertainment 7 System Tools Calculator Click here Command Prompt Administrator TD Notepad Y Paint 8 My Computer amp Windows Explorer A WordPad Startup 3 uoo Internet Explorer Figure 5 4 Command Prompt 2 The command prompt is started Input command ewfmgr C disable and then press Enter key Figure 5 5 Releasing Command 36 CONTEC PT E831H PT E831HS User s manual 5 Startup and Termination 3 Show as follows as soon as the releasing of write protect is
66. en protective sheet 1GB CompactFlash for Fix Disk 2GB CompactFlash for Fix Disk 4GB CompactFlash for Fix Disk 8GB CompactFlash for Fix Disk CF card slot x1 USBx1 Use 2 USB ports on PT E USBx1 Use 1 USB port on PT E PT E71IDE PWCBL PT E can supply 5V 12V DC power The usable currents are 5V 2A 12V 1A CONTEC PT E831H PT E831HS User s manual 113 10 List of Options A CAUTION 1 When connecting external devices expansion slot USB port or external DC output to PT E operating ambient temperature changes depending on the currents supplied to the external devices Follow the limitations shown in the Figure below 2 If currents supplied to external devices are DC5V 2A and DC12V 1A please use PT E under the operating ambient temperature 50 degrees 3 Ifuse PT E in the environment of operating ambient temperature 55 degrees currents supplied to the external devices should be under DCSV 2A and DC12V 0 5A DC12V load current limitation at the moment of using DCSV 2A Operating ambient temperature degree 55 n N PA E AA A Covered by warranty 0 5 1 0 12VDC load current A Check the CONTEC s Web site for the latest information on these options CONTEC 114 PT E831H PT E831HS User s manual Revision History Date Details os Revision PT E Series User s Manual PT E831H AC431x PT E831HS AC431x CONTEC CO LTD September 2011 Edition 3
67. ental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device CONTEC PT E831H PT E831HS User s manual 3 1 Introduction Safety Precautions Understand the following definitions and precautions to use the product safely Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources Understand the meanings of these labels to operate the equipment safely A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or in property damage Caution on the PT E Series Handling Precautions A WARNING Always check that the power supply is turned off before connecting or disconnecting power cables Procedures that could result in serious injury or loss of human life should never be performed from a touch panel Use system design methods that can guard against input errors Do not modify the product Always turn off the power before inserting or removing circuit boards or cables This product
68. entical start up disk once made the setting at the beginning not need to do calibration setting later However when exchange a start up disk and if a touch position is shifted do calibration setting again 1 Click Start on taskbar Move the cursor to All programs P UPDD and click Operation Setting Administrator Accessories Startup gt G UPDD Internet Explorer S Outlook Express amp Shortcut to StartUP All Programs fan cts gt Log OFF o Turn OFF Computer Click here Figure 6 1 Settings button CONTEC PT E831H PT E831HS User s manual 41 6 Setting the Touch panel Driver 2 Touch Panel Driver Properties window is displayed An CAUTION Click Calibration N tab Remove the checking of EEPROM Calibration Make calibration setting according to need Refer to next page Click Apply A button when change the settings so that the changed settings are available After completing all settings click Calibration C button Pointer Device Properties x Devices Hardware Settings Advanced Events General Windows Calibration Status About Calibration Settings For 3 7 Calibration Modes Device 1 z Normal v Add Remove Calibration Pattern Calibration Points x x x p 4 Calibration Timeout E alel x x x Start in at Coz 5 10 x x x x TF Transparent Background
69. er designed for PCI or ISA bus architecture t gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 13 IRQ n Resources When resources are controlled manually assign each system interrupt as on of the following type depending on the type of device using the interrupt Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific interrupt Such as IRQ4 for serial port 1 PCI ISA PnP Devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture The Choice Legacy ISA and PCI ISA PnP Table 8 14 IRQ n Resources Selections PCI VGA Palette Snoop PCI VGA Palette Snoop Disabled This item is designed to overcome some problems that can be Enabled caused by some non standard VGA cards This product includes a built in VGA system that does not require palette snooping so you must leave this item disabled Leave this field at Disabled Move ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 105 8 BIOS Setup PC Health Status Phoenix AwardBIOS COMS Setup Utility PC Health Status Menu Level gt gt e Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 14 PC Health Status PC Health Status displays
70. ergency Stop Wiring Example This section describes how to wire for Emergency stop EMG input connector Emergency stop switch EMER_COM2 ojo WDT_COM 24VDC EMER_COM1 Figure 4 16 Emergency Stop Wiring Example An CAUTION 1 Need wiring above when releasing the emergency stop for servo amplifier 2 When wiring for emergency stop always connect or disconnect to EMG connector after turning off the power supplied to PT E CONTEC 30 PT E831H PT E831HS User s manual 4 Each Component Function IDE Connector This product is equipped with a Connector for external HDD unit Use IDE connection cable and IDE power supply cable to fit the HDD unit N CAUTION Las Only one HDD unit can be connected to PT E For the HDD unit that is connected with IDE connection cable set the setting pin MASTER SLAVE as follows IDE connector l MASTER IDE connection cable must be 80 pin cable HDD unit might not work normally if use 40 pin cable DC Power Supply Connector This product is equipped with a Connector for IDE power supply cable PT 71IDE PWCBL Table 4 9 DC Power Supply Connector DC Power Supply Connector Vacant PCI Bus Expansion Slot This product is equipped with a Slot for Connecting an add on unit and use PCI bus expansion board CONTEC PT E831H PT E831HS User s manual 31 4 Each Component Function SSCNET Connector PT E831HS
71. es Setup This section allows you to configure your system for basic operation You have the opportunity to select the system s default speed boot up sequence keyboard operation shadowing and security Phoenix AwardBIOS COMS Setup Utility Advanced BIOS Featires Hard Disk Boot Priority Press Enter CPU L1 L2 Cache Enabled Quick Power On Self Test Enabled Menu Level gt First Boot Device Hard Disk Second Boot Device CDROM Select Har Disk boot Third Boot Device USB FDD Device Priolty Boot Other Device Enabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disa Typematic Rate Chars Sec 6 Typematic Delay Msec 250 Security Option Setu Summary Screen Show Di sal l l gt e Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 5 Advanced BIOS Features Setup CONTEC 86 PT E831H PT E831HS User s manual 8 BIOS Setup Hard Disk Boot Priority Phoenix AwardBIOS CMOS Setup Utility Hard Disk Boot Priority 1 ChO M TOSIHBA THNCF512MDG cea 2 Bootable Add in Cards Item Hel Menu Level gt gt Use lt gt or lt gt to select a device then press lt gt to move it up or lt gt to move it down the list Press lt ESC gt to exit this menu Move PU PD Change Priority F10 Save ESC Exit F5 Previous Values F6 Fail Safe
72. gure 3 3 setting the mounting fittings PT E831H PT E831HS 4 Tighten the screws of mounting fittings to fix PT E The tightening torque range is 6 3 to 8 4 kgf cm mies AER ares S oo Figure 3 4 Fixing PT E PT E831H PT E831HS CONTEC PT E831H PT E831HS User s manual 13 3 Hardware Setup Installation Requirements Be sure that the ambient temperature is within the range specified in the installation environment requirement by making space between the product and device that generates heat or exhaust air Installed angle which is recommended 30 Basically mount main body of PT E in vertical direction PT E must be mounted with a tilt of 30 or less from vertical when mounting it diagonally 30 or less if if A 80 130 AS 1 y 1 Pa ae Figure 3 5 Installed angle which is recommended Ax CAUTION Do not mount the main body of PT E upward or downward CONTEC 14 PT E831H PT E831HS User s manual 3 Hardware Setup Mounting Clearance of PT E le ef F y Thickness 1 6 to 5 Other pee or Unit mm control panel
73. is not intended for use in aerospace space nuclear power medical equipment or other applications that require a very high level of reliability Do not use the product in such applications If using this product in applications where safety is critical such as in railways automotive or disaster prevention or security systems please contact your retailer Do not attempt to replace the battery as inappropriate battery replacement poses a risk of explosion When disposing of a used battery follow the disposal procedures stipulated under the relevant laws and municipal ordinances Always power off the PT E before installing or removing it to or from an enclosure Not doing so can cause a failure fire or electric shock Always start wiring after powering off the PT E Not doing so can cause an electric shock or product damage Earth the equipment securely A failure to do so can cause an electric shock Before starting cleaning the PT E and or peripheral devices always power off the PT E and or peripheral devices Not doing so can cause a failure or electric shock Do not allow dust and foreign matter to enter the PT E and peripheral devices Doing so can cause a fire or electric shock CONTEC PT E831H PT E831HS User s manual 1 Introduction Do not allow your hands and foreign matter to enter the openings of the PT E and peripheral devices Doing so can cause injury or electric shock Always start the fitting of the e
74. itor start restart 30 seconds Charge ater circuit 2 Power restore from power failure None reset 3 Regularly 1Hr reset in the state of Charge prohibit 4 Regularly 60 days reset in the state of Charge end 5 Error occurred during charging Charge prohibit lamp blinking for 10 seconds or more during charging Display forecast result of encoder battery of servo amplifier that is connected to PT E Give an alarm when forecast ENC BAT 4 result is over 98 9 e F E Green Red Exchange Forecast This item is available when setting Execute for the item in Option setting refer to p 73 It is masked when setting Not Execute in Option setting 10 Alarm Reset button Reset all alarms shown in 1 Detect new alarm after reset None Monitor control voltage of circuit on motherboard and 11 Control Voltage Low i Green Red display the current state y Reset operating time Forecast result will be added up from Operating Time Reset j d 12 bati OHr after reset Do this operation when only exchanging None utton PT E main body Goes on using CF card Reset condenser longevity forecast result and the related a3 Condenser Longevity alarm message longevity warning Forecast result will be N one Forecast Reset button added up from 0 00 after reset Do this operation when only exchanging PT E main body Goes on using CF card CONTEC 66 PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor
75. ll CMOS value changes and exit setup CONTEC 80 PT E831H PT E831HS User s manual 8 BIOS Setup Standard CMOS Setup Phoenix AwardBIOS COMS Setup Utility Standard CMOS Features hase ada Pri May 11 2007 Time hh mm ss 14 5 31 Menu Level gt gt Onboard PATA Master None Onboard PATA Slave None Change the day month Onboard SATA 0 None year and century gt Onboard SATA 1 None Video EGA VGA Halt On No Errors Base Memory 640K Extended Memory 252928K Total Memory 253952K Figure 8 2 Standard CMOS Setup The items in Standard CMOS Setup Menu are divided into 11 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item CONTEC PT E831H PT E831HS User s manual 81 8 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Table 8 2 Main Menu Selections Set the system date Note that the Day Date Month DD YYYY automatically changes when you set the ate HH MM SS Set the system time lt gt J Onboard PATA Master Options are in its sub menu Press Enter fo enter the subimenuios etailed options lt gt 3 Onboard PATA Slave Options are in its sub menu Press Enee to enter the gub menud etailed options S gt Onboard SATA 0 Options are in its sub menu Press Enter to enla
76. mmunication mode to be used with the serial communication mode setting switches No 1 to No 7 eS Z a OZ N Gi SA Serial communication mode O OS A setting switches No 1 to No 7 EN Ol a Figure 4 15 Serial communication mode setting switches Table 4 7 Switch Setting of Communication Mode of Serial Port COM3 Communication Mode Switch Setting RS232C Default bee alle UU al An UL RS422 uncu DIP ON RS485 re RS485 ore fons so RS485 High baud rate DP ON OFF orr orr orr ox orr ox orr orr FF ON OFF OFF OFF ON ON OFF OF An CAUTION 1 Switch No 3 8 and 9 are set by maker They are unavailable for user PT E might not work normally if set them ON Do not set them ON please 2 Switch setting other than the patterns in Table 4 7 may lead to communication failure Do not set switches to pattern other than Table 4 7 CONTEC PT E831H PT E831HS User s manual 29 4 Each Component Function WDT EMG Connector This product is equipped with a Connector for WDT EMG Watchdog Timer can be set from 0 1sec to 25 5 sec and the signal can be output Table 4 8 WDT EMG Connector Connector used on D sub9 pin female the product WDT_NO Input 30VDC 2A or less WDT_NC Input 30VDC 2A or less El EMER_COM2 Ground for emergency stop input Se WDT_COM WDT_Common Em
77. n enter and change the options of the setup menus USER PASSWORD just can only enter but do not have the right to change the options of the setup menus When you select this unction the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press lt Enter gt You may also press lt Esc gt to abort the selection and not enter a password To disable a password just press lt Enter gt when you are prompted to enter the password A message will confirm the password will be disabled Once the password is disabled the system will boot and you can enter Setup freely PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup This prevents an unauthorized person from changing any part of your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time your system is rebooted This would prevent unauthorized use of your computer You determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password will be required both at boot and at entry to
78. nction setting Set whether or not to use resume function Y Use N Not Use Exit setting in continue mode Set whether or not to execute shutdown in continue mode ISN IS Y Execute N Not execute Encoder BAT exchange forecast setting Set whether or not to execute encoder BAT exchange forecast Not Execute IEU U Execute N Not Execute E Operation state output memory BIT setting B100 16 points from CB100 Set operation state output memory BIT Windows IB Not set Windows shared memory or Shared memory Set Set head number of shared memory CB are output If setting number is improper works by CBO CONTEC PT E831H PT E831HS User s manual 73 7 Resume Function EPC System Monitor Default Operation state output memory WORD setting Set operation state output memory WORD Not set Windows shared memory or Set Set head number of shared memory CW If setting number is improper works by CWO Example W100 8 points from CW100 are output Windows Shared memory IL Write event history information setting Set timing of writing event history information Y Write when event occurring N Not write n Write every setting time and at the time of exiting n 1 to 24 Unit hour If setting time is improper works based the following Works by n 1
79. need to be altered The default settings have been chosen because they provide the best operating conditions for your system The only time you might consider making any changes would be if you discovered that data was being lost while using your system Table 8 7 Advance Chipset Feature Selections DRAM Timing Selectable Manual By SPD DRAM Timing Selectable The value in this field depends on performance parameters of the installed memory chips DRAM Do not change the value from the factory setting unlees you install new memory that has a different performance rating than the original DRAMs t Move ENTER Accept ESC Abort CONTEC 92 PT E831H PT E831HS User s manual 8 BIOS Setup CAS Latency Time CAS Latency Time When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing Do not reset this field from the default value specified by the system designer ti Move ENTER Accept ESC Abort DRAM RAS to CAS Delay DRAM RAS to CASH delay This field lets you insert a timing delay between the CAS and RAS strobe signals used when DRAM is written to read from or refreshed Fast gives faster performance and Slow gives more stable performance This field applies only when synchronous DRAM is installed in the system Disabled System BIOS Cacheable Enabled Selecting Enabled allows caching of the system BIOS R
80. ng SSCNET communication then Standby mode is unavailable 2 Electrical currents that are supplied to external devices including those are connected to expansion slot USB port and external DC output only PT E831HS should be 5V 2A 12V 1A or less 3 For the LCD resolution there are about two dots upper and lower right and left are masked by the protective sheet Therefore please set the screen size in consideration of the masked range when creating a screen 4 When using both 2CH Ethernets in 1000BASE T please use PT E under the environment where the operating ambient temperature is Front display section is 0 C to 40 C other than display section is 0 C to 45 C 5 The capacity of CF is a value when 1GB is calculated by 1 billion bytes The capacity that can be recognized from OS CONTEC PT E831H PT E831HS User s manual 7 2 System Reference might be displayed fewer than an actual value Table 2 1 Functional Specification lt 2 2 gt PT E831H PT E831HS Resistive film analog type Input power supply Voltage AC100 to 240V 50 60Hz Terminal input Fie wiresize prora Touch Panel 65A or less 264VAC maximum load Cooling method Nature cooling no fan External dimensions 395 W x 310 H x 85 D 15 55 x 12 20 x 3 35 mm inch a 135VA maximum load 90VA no load only PT E main body Table 2 2 Installation Environment Requirements Model PT E831H PT E831HS
81. on battery pack Continuously charge the battery pack for eight hours and confirm Charge end by EPC System Monitor 3 For using resume function you must start software EPC System Monitor and do necessary settings Refer to next page 4 Use EPC System Monitor to set operation time of Continue mode or Standby mode Refer to p 68 An CAUTION Incase of connecting external devices if you are using resume function the currents supplied to the external devices should be under DCSV 1A Ifconnects external devices that supplying current more than DCSV 1A over current detection of lithium ion battery will work so that Continue mode and Standby mode can not work normally In this case recommend using an external UPS If lithium ion battery is not full charged PT E might go to shutdown operation even within the specified time If lithium ion battery is in the state of discharge under 6 7V resume function will not work CONTEC PT E831H PT E831HS User s manual 63 7 Resume Function EPC System Monitor EPC System Monitor Software EPC system monitor may watch system temperature in PT E it supports PT E s power supply unit and lithium ion battery pack on preservation and maintenance 1 2 Our company supplies Windows XP Embedded pre installed CF card in which EPC System Monitor has been installed User needs to do necessary settings Refer to p 68 and p 73 When using commercially av
82. ons Save amp Exit Setup PPC Health Status Exit Without Saving Esc Quit t Select Item F10 Save Exit Setup Time Date Hard Disk Type Figure 8 1 Main Manu Setup Items The main menu includes the following main setup categories Recall that some systems may not include all entries Standard CMOS Features Use this menu for basic system configuration Advanced BIOS Features Use this menu to set the Advanced Features available on your system Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system s performance Integrated Peripherals Use this menu to specify your settings for integrated peripherals PnP PCI Configuration This entry appears if your system supports PnP PCI Load Fail Safe Defaults Use this menu to load the BIOS default values for the minimal stable performance for your system to operate CONTEC PT E831H PT E831HS User s manual 79 8 BIOS Setup Load Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations While Award has designed the custom BIOS to maximize performance the factory has the right to change these defaults to meet their needs Supervisor User Password Use this menu to set User and Supervisor Passwords Save amp Exit Setup Save CMOS value changes to CMOS and exit setup Exit Without Save Abandon a
83. ration modes Add calibration modes the information that is set in 3 to 7 can be saved more than one time Click Add A button to show the following dialog box Input the name of calibration mode Click Remove R button to delete the calibration mode Gl Add Style x Enter name onee Figure 6 16 Add Style dialog box 3 Calibration points Specify the number of calibration points to be set The default is 4 points For revising a position difference correctly increase the number of the calibration points The setting range 2 to 25 points CONTEC 52 PT E831H PT E831HS User s manual 4 5 6 7 8 CONTEC 6 Setting the Touch panel Driver Timeout Indicate the calibration timeout value if the calibration point is not touched within the specified period Defined it in seconds The default is 10 seconds The setting range 10 to 60 seconds Starting Set the position of the calibration point On 4 corners of the screen it is 0 The bigger the setting value is the nearer the screen center position calibration point becomes The default is set to 5 Transparent Background If it is enabled specify that the calibration points are shown on the Windows desktop without a white background EEPROM Calibration Set where the calibration setting data are saved If enabled save the calibration setting data in EEPROM If disabled save the calibration dat
84. ry CB CW user screen Output data to Windows shared memory occupies 16 byte as bit data and 8 word as word data CONTEC PT E831H PT E831HS User s manual 71 7 Resume Function EPC System Monitor Bit data are shown as below Table 7 5 Output Bit data Output Memory Output Data Windows CB CW Memory Item shared memory CB Head number Content 0 Condenser Longevity alarm 0 Normal 1 PT E73BAT Exchange alarm Alarm 2 PT A6BAT Exchange alarm 3 Encoder battery exchange alarm 0 Fixed Power 4 Power outage outage Charge is 5 PT E73BAT Charge finished finished 6 PT E73BAT Charging Charging Charge is 7 PT E73BAT Charge Prohibit prohibited 8 Epcutil log file process error occurred setting 0 Normal 9 EpcutilLog txt file process error occurred event Alarm 10 UPCUtl inf file process error occurred alarm 11 PT E73BAT Low Voltage 12 PT A6BAT Low Voltage 13 CPU Over Temperature T Alarm 14 System Over Temperature 15 Control voltage low Word data are shown as below Table 7 6 Output Word data Output Memory Output Data Windows CB CW Memory Item shared memory CW head number 0 System Temperature degree 1 Condenser Longevity Forecast 0 01 2 PT E73BAT Exchange Forecast 0 01 3 PT A6BAT Exchange Forecast 0 01 4 Encoder battery Exchange Forecast 0
85. se Connect an isolating transformer if noise generated is excessive nos panair e BIE me i i equipment Isolating transformer Isolating transformer Figure 4 6 Isolating transformer CONTEC PT E831H PT E831HS User s manual 21 4 Each Component Function c The PT E I O equipment and power equipment should be wired separately as shown below Main power PT E power Main power PT E power supply supply supply supply 100VAC lt gt Cs PTE 200VAC S5 5 PT E T O power T O power TI supply supply T2 o I O wquipment ll T O wquipment Main circuit equipment o y Main circuit equipment Figure 4 7 T O equipment and Power equipment d When increasing power cable length twist cable as tightly as possible and connect it within the shortest distance e When increasing power cable length use cable as thick 2mm2 as possible to decrease voltage drop A CAUTION Do not bundle or run the power cable with the main circuit high voltage large current cables and T O signal cables Where possible run it at least 100 mm 3 94 inches away from them Normally use wire of 0 75 to 2 mm2 for power supply cable f As a measure against any potential surges due to lightening connect a surge absorber as shown below zt PTE Es Surge absorber for lightening protection Figure 4 8 Ground lightening surge absorber A CAUTI
86. splay color During starting or shutdown or EPC System Monitor is not Red blinking started or EPC System Monitor process error occurring During EPC System Monitor running Red lihgting During resume function working Green blinking CONTEC 20 PT E831H PT E831HS User s manual 4 Each Component Function AC Power Input Connector AC IN Power Supply Wiring Secure the cable terminals with screws in the FG N and L positions of the power supply terminals at the back of PT E Connect LG and FG terminals and directly earth them using an earth cable of 2mm2 or more PT E831H PT E831HS can use power supply voltage of 100VAC to 240VAC Do not connect PT E with an improper power supply voltage Doing so can cause a breakdown a gt INPUT ARQO e Q if ril ovp Figure 4 4 AC Power Connector Wiring Precautions This section gives the wiring guidelines for using PT E The following are the instructions for wiring the power cable 1 Power supply wiring a Connect a constant voltage transformer if voltage fluctuations are outside the specified range Constant voltage transformer LI PTE Figure 4 5 Constant voltage transformer b Across the terminals and across ground use power supplies that generate little noi
87. sume function PT E s operation state will be shifted to Continue Mode or Standby Mode after switching off power of PT E Within the setting time that has been set in EPC System Monitor PT E operates in either Continue Mode or Standby Mode PT E s operation state can be confirmed by operation state LED on the back of PT E Refer to p 20 Do not remove CF card during the operation state LED lighting on Doing so can lose data or damage the CF card Do not operate the power ON OFF switch near the CF card slot during operation state LED lighting on or blinking Doing so can lose data or damage the CF card CONTEC 40 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver 6 Setting the Touch panel Driver PT E is incorporated with the touch panel driver that allows you to operate it by touching screen Default settings are made by factory before shipment Use Touch Panel Driver Property application to make calibration settings if necessary Calibration Settings Calibration settings are used to adjust the recognized position when screen is touched There are two kinds of methods to do calibration setting One is a setting that doesn t use EEPROM calibration another is a setting that uses EEPROM calibration in the calibration setting Calibration Settings When Not Using EEPROM Calibration The setting that doesn t use EEPROM calibration saves the calibration data in the Windows When using the id
88. t time interval that the driver uses in the button click logic that uses time intervals between taps 3 Lift off time The Lift off Time value specifies the time interval required to register a stylus lift Lift off time is defined in units of 20ms This value is only used to perform a pen up if the Use Lift off packet is disabled otherwise Pen ups are generated as soon as the stylus leaves the pointer device display 4 Stabilization Stabilization causes small movements to be ignored 5 Averaging Apply a filter to produce smoother drawing Averaging takes the average of the last N co ordinates This is a very basic approach to filtering that can improve drawing and not affect drawing speed Use lift off pocket If enabled when click the screen it assumes separated immediately when separating a finger When input characters don t check the checkbox Default U button Press the Default U button to return to the default setting 6 a CONTEC 56 PT E831H PT E831HS User s manual 6 Setting the Touch panel Driver Advanced Used to do advanced settings including touch action beep etc Q Pointer Device Properties Devices Hardware Settings Advanced Events General Windows Calibration Status About Settings For Device 1 X TF Swap x IV Enabled IV Initialize 5 Touchdown filter Y Sound Sample rate J7 Anchor mouse Sound pitch Sound duration
89. thegub menu of etailed options ioe P lt Enter gt to enter the sub f Onboard SATA 0 Options are in its sub menu POSS or LO Une sup TER etailed options Select the default video device All Errors Select the situation in which you want the Halt On No Errors BIOS to stop the POST process and notify All but Keyboard you Base Memory N A Displays the amount of conventional memory detected during boot up Extended Memory N A Displays the amount of extended memory detected during boot up system CONTEC 82 PT E831H PT E831HS User s manual 8 BIOS Setup Onboard PATA Master Onboard PATA Slave Phoenix AwardBIOS COMS Setup Utility Onboard PATA Master IDE HDD Auto Detection Press Enter Onboard PATA Master Auto Menu Level gt gt Access Mode Auto To auto detect the Capacity 1024 MB HDD s size head on this channel Cylinder 1985 Head 16 Precomp 0 Landing Zone 1984 Sector 63 ll gt e Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 3 Onboard PATA Master Onboard PATA Slave Setup The IDE adapters control the CF card Use a separate sub menu to configure each CF card Use the legend keys to navigate through this menu and exit to the main menu Use Table 8 3 to configure the hard disk Table 8 3 IDE adapters Press Enter to auto detect the CF card on this channel If IDE HDD Auto detection
90. these items Third Boot Device The BIOS attempts to load the operating system from the devices in the sequence selected in these items Boot Other Device The BIOS attempts to load the operating system from the devices in the sequence selected in these items Boot Up NumLock Status Toggle between On or Off to control the state of the NumLock key when the system boots When toggled On the numeric keypad generates numbers instead of controlling cursor operations CONTEC 8 BIOS Setup Third Boot Device 15120 Hard Disk CDROM ZIP100 USB 4 DD USB ZIP USB CDROM LAN Third Boot Device LS120 Hard Disk CDROM ZIP100 USB DD USB ZIP USB CDROM LAN Disabled ty Move ENTER Accept ESC Abort Boot Other Device Dis abled Enabled ti Move ENTER Accept ESC Abort Boot Up NumLock Status ti Move ENTER Accept ESC Abort PT E831H PT E831HS User s manual 89 8 BIOS Setup Gate A20 option Gate A20 refers to the way the system addresses memory above 1 MB extended memory When set to Fast the system chipset controls Gate A20 When set to Normal a pin in the keyboard controller controls Gate A20 Setting Gate A20 to Fast improves system speed particularly with OS 2 and Windows Typematic Rate Setting When Disabled the following two items Typematic Rate and Typematic Delay are irrelevant Keystrokes repeat at a rate
91. tion point has been accepted 4 Clone Copy the current UPDD configuration setting into file upddclon reg which be used for automatic setup in subsequent installation Click Clone O button to create the file upddclon reg that is in folder C Program Files UPDD upddclon reg Double click the file to register the setting environment 5 Dump settings Use this function to dump driver and system settings to a text file UPDDset txt Click Dump setting M button to create a file UPDDset txt The file is in folder C Program Files UPDD UPDDset ttt CONTEC PT E831H PT E831HS User s manual 51 6 Setting the Touch panel Driver Calibration Used to make settings for calibration Pointer Device Properties xl Devices Hardware Settings Advanced Events General Windows Calibration Status About l Calibration Settings For Calibration dex 1 gt Device 1 Normal Remove Calibration Pattern Calibration Points A d Calibration Timeout A Start in at coz 65 C 10 bi Transparent Background 7 py EEPROM Calibration Figure 6 15 Calibration tab 1 Calibration Settings Specifies the device that these calibration setting apply to About the information of the controller you are using can be confirmed by Device in p 54 2 Calibration Modes Shows the calibration mode in use A device may have a number of different calib
92. when n lt 1 works by n 24 when n gt 24 Write when LN event occurring D Specify file save folder Specify folder by full path to save the following files that are output by EPC System Monitor System setting information file epcutil log Alarm state file UPCUtL inf Event history file EpcUtilLog txt Number of character Max 240 characters half size character Characters to be prohibited 3 2 lt gt Dd EPCSys Bas Work based default setting if no option setting is done 74 CONTEC PT E831H PT E831HS User s manual 7 Resume Function EPC System Monitor 2 Quit of EPC System Monitor Quit of EPC System Monitor only works when quitting Windows OS Shutdown request from Windows OS EPC System Monitor screen s quitting button doesn t work set EPC System Monitor Alarm USBka 2 Hf USB2 USB Fuse Blown USB2 FRB oo BEET System Temperature o Control Voltage Low sa o Le i CPUs CPU Temperature e USBta 2 8R VIAGRA o USB Fuse Blown Condenser Longevity Forecast o TEEF o MATH Low Voltage Exchange Forecast TER KRFA 9 Low e Exchange Forecast 649 E o TE Charge Discharee Count Bf e PI i Ep EEH tyh Gaia Gag ay ey pa Charee circuit reset 00 00 SURF ial Exchange Forecast 169 Figure 7 3 Quitting button Point 1 When exchanging CF card please copy EPC System Monitor related files such as
93. when the following message appears briefly at the bottom of the screen during the POST Power On Self Test Press DEL to enter SETUP If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON If USB Keyboard Support is set to Enabled restart can be initiated by pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys simultaneously If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press F1 to continue DEL to enter SETUP CONTEC PT E831H PT E831HS User s manual TT 8 BIOS Setup Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the PageUp and PageDown keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program using the keyboard y Ss o 9 a lt a e 5 ya n o e E Function Move to the previous item Move to the next item Move to the item on the left menu bar Move to the item on the right menu bar Main Menu Quit without saving changes Esc Submenus Exit Current page to the next higher level menu Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDn key Decrease the numeric value or make changes ke
94. xpansion board or memory after dismounting the PT E from the enclosure and placing it on a level surface Fitting it with the PT E mounted on the enclosure can cause injury due to a drop Do not touch the edges and projections of the electrical circuit boards and parts in the PT E Doing so can cause injury Before installing the cover always connect the internal cables securely Insecure connections can cause a fire due to a short circuit Always change the battery after powering off the PT E Not doing so can cause an electric shock A CAUTION CONTEC Do not use or store this product in a location exposed to high or low temperature that exceeds range of specification or susceptible to rapid temperature changes Example Exposure to direct sun In the vicinity of a heat source Do not use this product in extremely humid or dusty locations It is extremely dangerous to use this product with its interior penetrated by water or any other fluid or conductive dust If this product must be used in such an environment install it on a dust proof control panel for example Avoid using or storing this product in locations subject to shock or vibration that exceeds range of specification Do not use this product in the vicinity of devices that generate strong magnetic force or noise Such products will cause this product to malfunction Do not use or store this product in the presence of chemicals To clean this product wipe it gently
95. y Increase the numeric value or make changes key Decrease the numeric value or make changes Main Menu Quit and not save changes into CMOS Esc key Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu F1 key General help on Setup navigation keys F5 key Load previous values from CMOS F6 key Load the fail safe defaults from BIOS default table F7 key Load the optimized defaults F10 key Save all the CMOS changes and exit Getting Help In Case of Problems If after making and saving system changes with Setup you discover that your computer no longer is able to boot the AwardBIOS supports an override to the CMOS settings which resets your system to its defaults CONTEC 8 PT E831H PT E831HS User s manual PR 8 BIOS Setup Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu Note that a brief description of each highlighted selection appears at the bottom of the screen Phoenix AwardBIOS COMS Setup Utility Standard CMOS Features Load Fail Safe Defaults gt Advanced BIOS Features Load Optimized Defaults gt Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password gt PnP PCI Configurati
96. y Master PIO Menu Level gt gt IDE Primary Slave PIO IDE Primary Master UDMA If your IDE hard drive IDE Primary Slave UDMA supports block mode select Enabled for xk On chip Serial ATA Set automatic detection of On Chip Serial ATA the optimal number of block read writes per sector the drive can support li gt e Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 8 9 On Chip IDE Device Table 8 9 On Chip IDE Device Selections IDE HDD Block Mode IDE HDD Block mode Disabled Enabled Block mode is also called block transfer multiple commands or multiple sectors read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support ti Move ENTER Accept ESC Abort On Chip Primary PCI IDE Disabled Enabled On Chip Primary PCI IDE The integrated peripheral controller contains an IDE interface with support for 2 IDE channels Select Enabled to activate each channel separately 14 WMove ENTER Accept ESC Abort CONTEC PT E831H PT E831HS User s manual 97 8 BIOS Setup IDE Primary Master Slave PIO The two IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for the one IDE device that the onboard IDE interface

PT-E831H-AC431x, PT-E831HS

Contents

Download Pdf Manuals

Related Search

Related Contents