POOL PUMPS - Advantage Manufacturing
Contents
1. Close the manual air relief valve WINTERIZING 1 If the air temperature drops below 35 F the water in the pump can freeze and cause damage Freeze damage is not warrantable 2 To prevent freeze damage follow the procedures listed below a Shut off electrical power for the pump at the house circuit breaker b Drain the water out of the pump case by removing the two drain plugs from the case Store the plugs in the pump basket c Cover the motor to protect it from severe rain snow and ice d Do not wrap the motor in plastic It will cause condensation and rust on the inside of the motor CARE OF ELECTRIC MOTOR 1 Protect from heat a Shade the motor from the sun b Any enclosure must be well ventilated to prevent overheating c Provide ample cross ventilation 2 Protect against dirt a Protect from any foreign matter or splashing water b Do not store or spill pool chemicals near the motor c Avoid sweeping or stirring up dust near the motor while it is operating d If a motor has been damaged by it voids the warranty 3 Protect against moisture a Protect from splashing pool water b Protect from the weather c Protect from lawn sprinklers d If a motor has become wet let it dry before operating Do not allow the pump to operate if it has been flooded e If a motor has been damaged by water it voids the motor warranty NOTE DO NOT wrap motor with plastic of other air tight materials The motor2. and wipe off the ceramic and carbon faces with a clean cloth Remount the seal plate to the motor 4 Screw the impeller onto the motor shaft Figure 4 Face Plate Pump Impeller Seal Motor Shaft Hex Diffuser Assembly 5 Screw in the impeller lock screw counter clockwise to tighten 6 Remount the diffuser onto the seal plate 7 Grease the O ring with Teflon or silicone 8 Assemble the motor sub assembly to the strainer pot pump body Do not tighten down any of the bolts until all 6 bolts are in place and finger tight 9 Fill the pump with water 10 Reinstall the pump lid by turning clockwise until hand tight Do not over tighten with tools PARTS LIST FOR QUIETFLO PUMP Item PartNo Part Description 1 58921 Trap Lid 2 58922 Trap Lid O Ring 3 58923 Basket 4 58924 Pump Housing 5 58925 Diffuser Plate 6 58926 Diffuser O Ring 7 58927 Diffuser Assembly 8 58928 Diffuser Bolt 9 58929 Left Hand Screw 10 58930 Gasket Left Hand Screw 11 58931 Champion Impeller 1 2HP 11A 58932 Champion Impeller 3 4HP 11B 58933 Champion Impeller 1HP 11C 58934 Champion Impeller 1 5HP 11D 58935 Champion Impeller 2HP 11E 58936 Champion Impeller 3HP 12 58937 Pump Seal Set 13 58938 Seal Plate Gasket Item Part No Part Description 14 58939 Seal Plate 15 58940 3 8 Washer 16 58941 3 8 16 X 1 1 4 Bolt 17 58942 3 8 16 X 7 8 18 58943 1 2SQ Motor 1 2HP 18A 58944 3 4SQ Motor 3 4
3. in whole or in part by buyers breach of any provision term or condition of purchase BINDING EFFECT All sales transactions are binding on APP and the buyer and their respective directors officers employees agents subcontractors successors and permitted assigns GOVERNING LAW All transactions will be interpreted and enforced under the laws of the State of California including without limitation the Uniform Commercial Code as adopted by the California without recourse to the conflict of laws provision thereof In no event will the provisions of the UN Convention of the International Sale of Goods apply to any purchases APP and buyer agree that any action or proceeding arising out of or in connection with any sale of product or service will be brought exclusively to a court of competent jurisdiction in the County of Orange State of California THE LIMIT OF LIABILITY FOR ANY CLAIMS SHALL NOT EXCEED THE AMOUNT PAID OR PREPAID ON ACCOUNT BY BUYER FOR THE GOODS GIVING RISE TO SUCH CLAIMS BUYER SHALL BE DEEMED TO ASSUME ALL LIABILITY FOR ANY AND ALL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR MISUSE OF THE GOODS BY BUYER ITS EMPLOYEES CUSTOMERS AND OTHERS SELLER SHALL NOT BE LIABLE FOR AND BUYER AGREES TO INDEMNIFY DEFEND AND HOLD SELLER HARMLESS FROM ANY CLAIMS BASED ON SELLER S COMPLIANCE WITH BUYER S DESIGNS SPECIFICATIONS OR INSTRUCTIONS OR MODIFICATION OF ANY GOODS BY PARTIES OTHER THAN SELLER OR USE IN COMBINA
4. lt gt Q ADVANTAGE ADVANTAGE MANUFACTURING POOL PUMPS QUIETFLO OWNER S MANUAL INSTALLATION OPERATION amp PARTS To prevent potential injury and to avoid unnecessary service calls read this manual carefully and completely AN CAUTION We highly recommend a qualified professional install and service this product AN WARNING This manual contains important safety information that must be furnished to the end user of this product FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY SAVE THIS INSTRUCTION MANUAL gt 624 South B Street e Tustin CA 92780 gt Toll Free 800 636 8866 e Tel 714 505 1166 e Fax 714 505 1160 ADVANTAGE advantageman com MANUFACTURING C PRODUCT REGISTRATION Q MANUFACTURING Retain For Your Records ee DATE OF INSTALLATION INITIAL PRESSURE GAUGE READING CLEAN FILTER PUMP MODEL HORSEPOWER IMPORTANT SAFETY INSTRUCTIONS Before installing or servicing this electrical equipment turn power supply OFF Basic safety precautions should always be followed including the following Failure to follow instructions may result in injury AN This is the safety alert symbol When you see this symbol on your pump manual look for one of the following signal words and be alert to the potential for personal injury AN WARNING vwarns about hazards that could cause serious personal injury death or major property damage and if ignored presents a potential haz
5. HP 18B 58945 1SQ Motor 1HP 18C 58946 1 5SQ Motor 1 5HP 18D 58947 2SQ Motor 2HP 18E 58948 3SQ Motor 3HP 19 58949 Motor Support Strip 20 58950 Motor Support Base 21 58951 Hex Screw 1 4 X 1 1 4 22 58952 Drain Plug O ring 23 58953 3 8 Drain Plug 1 YEAR LIMITED WARRANTY CLAIMS All claims must be made within ten 10 calendar days after receipt of the merchandise If any shipment is Here received in a damaged condition your claim must be filed with the delivering carrier and noted on the freight bill before you accept the merchandise RETURNS All returns are subject to our written approval and must be accompanied by a Return Goods Authorization number obtained from APP prior to shipment Unauthorized returns will not be accepted Freight must be prepaid Material returned for credit if in original condition and resalable is subject to a 20 handling charge TAXES Any Federal or State Excise or Sales Tax for which APP may be liable on any sale will be charged to and paid by the buyer Buyer is responsible for furnishing a resale certificate PRICES Prices and Products are subject to change without notice LIMITED WARRANTY To Buyer as original purchaser of the Goods APP warrants its products free from defects in materials and workmanship for a period of one year from the date of purchase Parts which fail or become defective during the warranty period except as a result of freezing negligence improp
6. S EMPLOYEES OFFICERS OR DIRECTORS AGENTS SUCCESSORS OR ASSIGNS BE LIABLE TO ANYONE UNDER ANY PRODUCT ORDER SCHEDULE OR TERMS AND CONDITIONS HEREIN UNDER ANY CONTRACT STRICT LIABILITY TORT INCLUDING NEGLIGENCE OR OTHER LEGAL OR EQUITABLE THEORY WHETHER OR NOT FORESEEABLE OR FORESEEN FOR 1 BUSINESS INTERRUPTION COSTS COST OF REWORK RETESTING PROCUREMENT OF SUBSTITUTE GOODS REMOVAL AND RE INSTALLATION OF GOODS OR 2 ANY SPECIAL INCIDENTAL EXEMPLARY INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS LITIGATION COSTS LOSS OF EQUIPMENT PRODUCTION OR PROFIT GOODWILL LOSS OF REVENUE OR LOSS OF UNITS COST OF RENTING REPLACEMENTS AND OTHER ADDITIONAL EXPENSES EVEN IF THE AP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THERE IS A TOTAL AND FUND A MENTAL BREACH OF THIS AGREEMENT OR WHETHER ANY REMEDY PROVIDED HEREIN FAILS OF ITS ESSENTIAL PURPOSE APP S LIABILITY AND BUYER S SOLE REMEDY WHETHER IN CONTRACT UNDER WARRANTY IN TORT INCLUDING NEGLIGENCE IN STRICT LIABILITY OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY BUYER AND SHIPMENT COSTS INDEMNIFICATION Buyer will defend and indemnify APP and its directors employees agents customers end users successors and assigns from and against all actual and alleged claims liabilities suits damages losses and expenses including attorney s fees and legal costs arising from or caused
7. TION WITH OTHER PRODUCTS EACH PARTY RECOGNIZES AND AGREES THAT THE WARRANTY DISCLAIMERS AND LIABILITY AND REMEDY LIMITATIONS HEREIN ARE MATERIAL BARGAINED FOR BASES OF ANY ORDER OR CONTRACT AND THAT THEY HAVE BEEN TAKEN INTO ACCOUNT AND REFLECTED IN DETERMINING THE CONSIDERATION TO BE GIVEN BY EACH PARTY UNDER ANY ORDER OR CONTRACT AND IN THE DECISION BY EACH PARTY TO ENTER INTO SUCH ORDER OR CONTRACT Copyright Notices Polaris is a registered trademark of Zodiac Pool Care Inc Letro is a registered trademark of Letro Products Sta Rite is a registered trademark of Sta rite Industries Hayward is a registered trademark of Hayward Manufacturing Co Inc WhisperFlo is a registered trademark of Pentair Pool and Spa Inc Noryl is a registered trademark of GE Plastics Northstar is a trademark of Hayward Manufacturing Co Inc Cal Spas is a registered trademark of California Acrylic Industries Inc Aquaflo is the registered trademark of LSP Products Group Inc Vico is a registered trademark of Vico Industries Waterway is a registered trademark of Waterway Plastics Advantage Manufacturing is trademark of Advantage Manufacturing Federal Copyright Advantage Manufacturing 2007
8. and filter and for proper operation of the system clean pump strain and skimmer baskets regularly PUMP STRAINER BASKET CLEANING PROCEDURES 1 Turn off motor 2 Relieve pressure in the system 3 Turn the lid in a counter clockwise direction until it stops 4 Lift lid and remove basket 5 Put the debris from the basket into the trash and rinse out the basket If the basket is cracked it should be replaced 6 Replace the basket and fill the pump pot and volute up to the inlet port with water 7 Clean the cover a ring and sealing surface of the pump pot Grease the O ring with Teflon or silicone 8 Reinstall the lid See Figure 2 a Make sure the lid a ring is properly placed Seat the lid then turn clockwise until hand tight Do not over tighten with tools See Figure 3 9 Turn the power ON at the house circuit breaker Reset the pool time clock to the correct time AN WARNING THIS FILTER OPERATES UNDER HIGH PRESSURE WHEN ANY PART OF THE CIRCULATION SYSTEM e g LOCK RING PUMP FILTER VALVES ETC IS SERVICED AIR CAN ENTER THE SYSTEM AND BECOME PRESSURIZED PRESSURIZED AIR CAN CAUSE THE LID TO BLOW OFF WHICH CAN RESULT IN SEVERE INJURY DEATH OR PROPERTY DAMAGE TO AVOID THIS POTENTIAL HAZARD FOLLOW THESE INSTRUCTIONS 10 Open the manual air relief valve on top of the filter 11 Stand clear of the filter Start the pump 12 Bleed air from the filter until a steady stream of water comes out
9. ard AN CAUTION warns about hazards that will cause or can cause minor or moderate personal injury and or property damage and if ignored presents a potential hazard It can also make consumers aware of actions that are unpredictable and unsafe The NOTICE label indicates special instructions that are important but not related to hazards AN WARNING Read and follow all instructions in this owner s manual and on equipment Failure to follow A Z e e e e instructions can cause severe injury and or death a II S Q NOTE When pump is mounted permanently within 5 ft of the inside walls of a swimming pool you must use a NO 8 AWG or larger conductor to connect to bonding conductor lug A WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times A CAUTION For hot tubs and spa pumps do not install within an outer enclosure or beneath the skirt of a hot tub or spa unless so marked GENERAL INFORMATION WIRING AN WARNING Risk of electrical shock or electrocution This pool pump must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances Improper installation will create an electrical hazard which could result in death or damage to property Always disconnect power to the pool pump at the circuit breaker before servic
10. er installation use or care shall be repaired or replaced at our option within ninety 90 calendar days of the receipt of the defective product barring unforeseen delays To obtain warranty replacements or repair defective components or parts should be returned transportation paid to the place of purchase No returns may be made directly to the factory without the express written authorization of APP Pump housing strainers which become defective during the warranty period except as a result of freezing negligence improper installation use or care or as the result of use in association with an automatic valving system shall be repaired or replaced at APP s option without charge All other conditions and terms of the standard warranty apply APP shall not be responsible for cartage removal and or re installation labor or any other cost incurred in obtaining warranty replacements The foregoing warranty does not apply to components manufactured by others For such products the warranty established by the respective manufacturers will apply LIMITATION ON IMPLIED WARRANTIES Implied warranties including any warranty or merchantability imposed on the sale of the goods under state law are limited to one year duration for the goods or any parts LIMITATIONS OF LIABILITY THE ESSENTIAL PURPOSE OF THIS PROVISION IS TO LIMIT APP S LIABILITY HEREUNDER EXCEPT FOR BODILY INJURY OR DEATH OF A PERSON UNDER NO CIRCUMSTANCES WILL APP IT
11. ing the pump Failure to do so could result in death or serious injury to serviceman pool users or others due to electric shock 1 Make sure all electrical breakers and Chart 1 switches are turned off before wiring motor SUPPLY WIRE SIZES AWG 2 Make sure that the wiring voltage ve NN matches the motor voltage 230v or 115 Volts 230Volts 115v If they do not match the motor 50 Ft 100 Ft 150 Ft 50 Ft 100 Ft will burn up 14 14 12 14 14 3 Choose a wire size from Chart 1 When in doubt use a heavier gauge larger 14 12 10 14 14 diameter wire Heavier gauge will 12 12 10 14 14 allow the motor to run cooler and more efficient 12 10 8 14 14 10 14 14 4 Cut wires to the appropriate length so they don t overlap or touch when 10 14 12 connected to the terminal board 12 12 5 Make sure all electrical connections are clean and tight External Internal 6 Permanently ground the motor using Bonding Grounding the internal green ground terminal located on the inside of the motor canopy or access plate see Figure 1 Use the correct wire size and type specified by National Electrical Code Make sure the ground wire is connected to an electrical service ground 7 Bond the motor to the pool structure in accordance with the National Electrical Code Use a solid NO 8 AWG or larger copper conductor Run a wire from the brass external bonding clamp see Figure 1 to the pool bo
12. may be covered during a storm for winter storage etc but never when operating or expecting operation SERVICE AN WARNING Risk of electrical shock or electrocution This pool pump must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances Improper installation will create an electrical hazard which could result in death or damage to property Always disconnect power to the pool pump at the circuit breaker before servicing the pump Failure to do so could result in death or serious injury to serviceman pool users or others due to electric shock A WARNING DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot Pumps operated in these circumstances may experience a build up of vapor pressure and may contain scalding hot water Opening the pump may cause serious personal injury In order to avoid the possibility of personal injury make sure the suction and discharge valves are open and strainer pot temperature is cool to touch then with extreme caution PUMP DISASSEMBLY 1 All moving parts are located in the rear sub assembly of this pump Tools required a 1 2 inch open end wrench b 9 16 inch open end wrench c Flat and Phillips head screwdrivers 2 To remove and repair the motor sub assembly perform the following procedures a Turn off the pu
13. mp circuit breaker at the main panel b Drain the pump by removing the drain plugs c Remove the 6 bolts that hold the main pump body strainer pot volute to the rear sub assembly d GENTLY pull the two pump halves apart removing the rear sub assembly e Remove the diffuser A CAUTION Be sure not to scratch or mar the polished seal faces Seal will leak if faces are damaged f Hold the impeller securely in place and remove the impeller lock screw by using a Phillips head screwdriver The screw is a left handed thread and loosens in aclockwise direction g Remove the shaft cap located at the back of the motor and hold the shaft secure with a flat head screwdriver Century or 7 16 inch open end wrench Franklin h To unscrew the impeller from the shaft twist the impeller counter clockwise i Remove the four bolts from the seal plate to the motor using a 9 16 inch wrench j Place the seal plate face down on a flat surface and tap out the carbon spring seal k Clean the seal plate seal housing and motor shaft PUMP REASSEMBLY SEAL REPLACEMENT SEE FIGURE 4 fe When installing the replacement ceramic carbon seal use silicone sealant on the metal portion before pressing into the seal plate 2 Before installing the ceramic section of 3 the seal into the impeller be sure the impeller is clean Use a light density soap and water to clean the seal Press the seal into the impeller with your thumbs
14. nding structure 8 Connect the pump permanently to a circuit Make sure no other lights or appliances are on the same circuit NOTE I the pump is installed below the water level of the pool close return and suction lines prior to opening hair and lint pot on pump Make sure to re open valves prior to operating 3 THE PUMP STRAINER BASKET This unit sometimes referred to as the Hair and Lint Pot is the unit in front of the volute Inside the chamber is the basket which must be kept clean of leaves and debris at all times View basket through the See Through Lid to inspect for leaves and debris Regardless of the length of time between filter clean ing it is most important to visually inspect the hair and lint pot basket at least once a week A dirty basket will reduce the efficiency of the filter and heater and also put an abnormal stress on the pump motor which would result in a costly repair bill MAINTENANCE AN WARNING DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot Pumps operated in these circumstances may experience a build up of vapor pressure and may contain scalding hot water Opening the pump may cause serious personal injury In order to avoid the possibility of personal injury make sure the suction and discharge valves are open and strainer pot temperature is cool to touch then with extreme caution AN CAUTION To prevent damage to the pump
Download Pdf Manuals
Related Search