SoftForm Premier Active 2 User Manual
Contents
1. Deutsch 40 50 60 70 80 Rotor Failure Espanol Alarm event Low Pressure Italiano Portugu s Svenska Dansk Norsk 1576248 C Invacare Softform Premier Active 2 and Active Care 5 4 Control unit Menu Display LCD display screen Up arrow button OK button Silence alarm Softform Active 2 O Down arrow button 3 Green LED light Task Action Display Power up Push main switch of control unit 3 audible beeps System set up LU LCD illuminates see figure above Green light illuminates see figure above System set up displayed on LCD display After 10 minutes System OK displayed on LCD display 2 Menu option System OK 008 Cannot enter menu The menu can only be served after the system has gone through full cycle set up and System OK is displayed on the LCD display Wait until set up is complete System OK System OK can take up to 15 minutes to complete cycle 3 Power down Move control unit switch to off position See figure above 2 Disconnect from power source The LCD display and the green LED go out 1576248 C Usage Task Action Display 3 How to enter menu System OR 1 s System OK 2 Press arrow Up then Pres2. otherwise injury or damage may occur T WARNING Risk of developing pressure ulcers Bed sheets must be loosely fitted with creases smoothed out Care must always be taken to ensure that the support surface in contact with the user is kept free from crumbs and other food debris and that drip cables stents and other foreign objects do not become entrapped between the user and the pressure reducing surface of the mattress as this may result in the development of pressure ulcers WARNING Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products The introduction of certain third party products between the cushion surface and the user may reduce or impede the clinical effectiveness of this product Third party products may include but are not limited to items including under blankets plastic sheets and sheepskins etc Heated over blankets must only be used in consultation with a suitably qualified health care professional as an increase in temperature can increase the risk of developing pressure ulcers WARNING Risk of fire or explosion A cigarette can burn a hole in the bed surface and cause damage to the mattress Also patient clothing bed sheets etc may be combustible and cause a fire Failure to observe this warning can
3. 0 0 00 eee eee eee 11 5 2 CPR proc ed re us q imay usu uu eee eee u 12 5 3 Control unit Software Schematic 13 5 4 Control unit Menu Display 14 6 Transport s z u ee ae en ae 16 6 1 Safety information 16 6 2 Transport Mode een nen 16 7 Maintenance I7 7 1 Inspection multiple use 17 72 Cleaning and care een 17 8 After Use Sa oot tie N R ate oe RRR 20 8 1 Storage ns ar ra 20 8 2 Re Use porera neer eta an 20 8 3 S ee T coat aia ae a Dante sr sahen 20 9 Troubleshooting 21 9 1 Identifying and repairing defects 21 10 Technical data 23 10 1 General Dat 2 22 sys era am 23 10 2 Control unit o ooooocooooo o eee 24 10 3 Materials ana SR rl 24 10 4 Environmental Parameters 24 19 5 Spare parts unica e oa ea ee 24 Invacare Softform Premier Active 2 and Active Care General 1 1 General information Essential nursing care is pivotal in pressure ulcer prevention These mattresses will positively contribute to the outcome of a pressure ulcer prevention care plan Education clinical judgement and action based planning based on vulnerability are fundamental factors in the prevention of pressure ulcers A range of assessment scales can be used as a for
4. directive 93 42 EEC for medical products The launch date for this product is specified in the CE declaration of conformity Manufacturer 1 3 Warranty We provide a manufacturer s warranty for the product in accordance with our General Terms and Conditions of Business in the respective countries Guarantee claims can only be made through the provider from whom the appliance was obtained Standard Invacare Terms This is to certify that your Invacare Softform Mattress is warranted by Invacare Ltd for a period stated in the Table Technical Data of this user guide The Warranty of your Invacare Softform product is valid from time of shipping 1576248 C If a defect or fault is discovered the Invacare customer or Local Business Development Manager from whom the appliance was obtained must be notified immediately The manufacturer will not accept responsibility for damage caused by misuse or non observance of the instructions set out in this user guide During the period of the warranty any products that have become defective due to faulty workmanship or materials will be renewed without charge The warranty will be forfeited should any unauthorized alteration be made to the equipment Both warranty and fire retardancy Certification will become null and void if non Invacare spares are used on any Invacare Mattress products The purchaser s statutory rights under the Consumer Protection Act are not affected 1 4 St
5. full cycle set up and System OK displayed fl In the event of an alarm the audible sound can be muted by pressing the OK button The LCD display and Green light will flash to indicate the alarm is still evident See figure 5 4 Control unit Menu Display page 14 Once muted the system will automatically go into set up mode to check the diagnostics of the system If the fault reoccurs after the system has been through set up the pump alarm will sound again to notify the user of the fault In case of issues with troubleshooting please contact Invacare for further assistance contact details on the back page of this User Manual Ho 22 1576248 C 10 Technical data Technical data 10 1 General Data Product Warranty Firetesting Grade ref 8 Nominal Nominal Maximum user Weight of Colour density range hardness weight kg product kg m3 range N kg o E SOFTFORM Cover 4 years EN 597 1 RX 39 120 Pink 38 _ 40 105 135 PREMIER ACTIVE 2 Foam 8 years EN 597 2 RX 39 200 Blue 38 _ 40 180 _ 200 247 6 14 ACTIVE CARE Pump 2 years BS 7177 Crib 5 1 Warranty is against manufacturing defects 2 Based on the weight of a standard size mattress This can change if different sizes are ordered Warranty on air cell insert 2 years Air cell height 75 mm 1576248 C 23 Invacare Softform Premier Active 2 and Active Care 10 2 Control unit 10 4 Environ
6. or nitrous oxide Wipe all controls pump casing and hose fittings with a quaternary disinfectant solution Using a nylon brush gently clean all crevices as they can harbor microorganisms Air dry all treated surfaces Cleaning covers Removal of contaminants such as dust and organic matter l 2 Remove all covers for laundering Launder the covers with the recommended temperature at 80 C using a diluted detergent solution Instructions on label IMPORTANT Washing at higher temperatures will cause shrinkage Invacare Softform Premier Active 2 and Active Care Drying covers Hang mattress covers from a line or bar and drip dry in a clean indoor environment or Tumble dry on a low heat setting IMPORTANT Tumble dry setting must not exceed 40 C Do not tumble dry for longer than 10 minutes Dry thoroughly before re fitting to the foam Disinfecting covers Reducing the number of microorganisms Please contact your hygiene specialist in the event of contamination IMPORTANT Ensure that any residual detergent has been removed prior to disinfection Light soilage Wipe down the cover with a 0 1 Chlorine Solution 1 000 ppm 2 Rinse the cover with clean water using a single use nonabrasive cloth 3 Dry the cover thoroughly Heavy soilage Where the mattress is badly soiled we recommend cleaning with a dilute cleaning solution at 80 C in the washing ma
7. place hypodermic needles venflons scalpels or other similarly sharp objects onto the mattress Ensure that all venflons are taped down correctly with no sharp edges exposed When using patient transfer aids care should be taken not to damage the mattress All transfer aids should be checked for any sharp edges or burrs before use as these can damage the mattress Make sure that the mattresses are not jammed or damaged by sharp edges when used on beds with an adjustable frame When using the mattress on a profiling bed ensure that the knee break is used before the backrest Invacare Softform Premier Active 2 and Active Care 5 2 CPR procedure The Softform Premier Active 2 Active Care mattress has been fully tested to comply with the current CPR standard of 4 5 cm compression depth This was achieved at all stages of inflation deflation A report on these findings conducted by the Resuscitation Unit at the University Hospital of Wales Cardiff is available upon request l Hold down Red CPR button 2 Pull hose connector firmly away from the control unit 3 Switch off the control unit il Mattress will start to deflate The deflation time is 20 seconds 4 When CPR is complete reactivate the system following section 4 2 Installing the system page 10 1576248 C Usage 5 3 Control unit Software Schematic Switch on pump System Setup Es 7 m Language System OK Pressure 60mmHg Fran ais I
8. pressure reduction to users when the product is in normal use which is defined by Invacare Ltd as when the support surface is covered with a cotton cotton combination or linen bed sheet and any one of these would be the only item deployed between the support surface and the user Operator action is required to change settings only 1 6 Service life We estimate a life expectancy of five years for these products provided they are used in strict accordance with the intended use as set out in this document and all maintenance and service requirements are met The estimated life expectancy can be exceeded if the product is carefully used and properly maintained and provided technical and scientific advances do not result in technical limitations The life expectancy can also be considerably reduced by extreme or incorrect usage The fact that we estimate a life expectancy for these products does not constitute an additional warranty Invacare Softform Premier Active 2 and Active Care 2 Safety Safety information WARNING Do not use this product or any available optional equipment without first completely reading and understanding the user manual supplied Invacare product manuals are available at www invacare co uk or your local dealer If you are unable to understand the warnings cautions or instructions please contact a health care professional dealer or technical personnel before attempting to use this equipment
9. Invacare Softform Premier Active 2 and Active Care en Mattresses User Manual KO trirkoressurecore INVACARE This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference Yes you can 2015 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Contents General sur yu ERA ee een 4 l l General information 22222220 4 1 2 Symbols in this user manual 4 E Warranty ici ii ee ee e do Rn 4 1 4 Standards and regulations 2222220 een 5 1 5 Intendeduse 2 222220 rennen en 5 1 6 Service lie ioe ra do etala at a dana ATE da i 5 2 Safety LTR ee ie 6 2 1 Safety information eee 6 2 2 EMC information a ee eee eee eee 7 2 3 Symbols on theproduct 7 3 Components S RRR cece cece eee R cece RER R KTR 8 3 1 Product description 8 3 2 Components ern 8 AES COUP tics cos rico keine nee 9 4 1 Safety Information 0 2 0 eee eee 9 4 2 Installing the system 00 0000 20 eee eee 10 5 Us ge i seo uite c a acuza oy a E A lI 5 1 Safety information
10. Phone 1800 460 460 Fax 1800 814 367 orders invacare com au www invacare com au p Invacare UK Operations Limited Pencoed Technology Park Pencoed Bridgend CF35 5AQ UK 1576248 C 2015 09 09 Making Life s Experiences Possible Yes you can
11. and fuse is good control unit does not come Send control unit back to Invacare for repair properly ER Major leak in air cell Replace leaking air cell CPR hose or tube connectors kinked or split Unkink or replace split CPR hose or tube connectors Not alternating rotor failure Send control unit back to Invacare for repair No air control unit failure Send control unit back to Invacare for repair No power Control unit off Check power source turn unit on Power cord disconnected Connect power cord and ensure the power source is on No power in the power source Check the power source has power and turn it on Power outage Wait till the power source has power Fuse blown Change fuse on power inlet connector with spare fuse or identical replacement only consult a trained engineer if you are unsure how to change a fuse Cannot enter menu System set up not complete Wait until set up is complete and System OK displayed Low pressure alarm Low Pressure displayed with audible beeps Disconnection of CPR connection hose Connect hose properly Disconnection of connector tubes to air cells in air insert Check individual air cells in insert are correctly connected to connector tubes 1576248 C 21 Invacare Softform Premier Active 2 and Active Care Low pressure alarm will only function after the system has gone through
12. andards and regulations Quality is fundamental to the company s operation working within the disciplines of ISO 9001 and ISO 13485 All Invacare Softform Mattress products feature the CE mark in compliance with the Medical Device Directive 93 42 EEC Class Invacare is continuously working towards ensuring that the company s impact on the environment locally and globally is reduced to a minimum We comply with the current environmental legislation e g WEEE and RoHS directives We only use REACH compliant materials and components The foam and cover used to manufacture the Invacare Softform range of mattresses are independently tested and certified in accordance with EN 597 1 EN 597 2 and BS 7177 Crib 5 The control unit is tested to EC Directive 2004 108 EEC and EN 55011 Manufactured to comply with EN 60601 1 For further information please contact Invacare in your country addresses see back page of this manual 1576248 C General 1 5 Intended use This pressure redistribution mattress and control unit are intended to be used in conjunction with an appropriately sized bed frame as part of an overall pressure ulcer prevention program of care lt can be used safely in static mode deflated for static pressure redistribution or in dynamic mode inflated should an alternating pressure support surface be required Any other use is prohibited This product has been designed to deliver effective
13. chine il Large spillages of blood should be absorbed and removed with paper towels first followed by as above Clean up all spillages of bodily fluids i e blood urine faeces sputum wound exudater and all other bodily secretions as soon as possible using a 1 Chlorine Solution 10 000 ppm 2 Rinse with clean water using a single use nonabrasive cloth 3 Dry the cover thoroughly IMPORTANT Polyurethane coated fabrics can absorb liquids for short periods causing a temporary change to the polyurethane characteristics The mattress cover swells temporarily and is more vulnerable to physical damage for a period after it is completely surface dried by which time it will revert to its previous state IMPORTANT 1 Chlorine Solution used on a regular basis can diminish the life of the cover if not rinsed and dried properly Do not use granules WARNING Remove contaminated foams from use CAUTION Keep clear of open heat sources gt amp 1576248 C IMPORTANT Do not use phenols alcohols bleaches or other abrasive materials Replacing covers Unzip the cover and remove it carefully from the foam core 2 Place new cover onto the foam core 3 Then close the zipper IMPORTANT Ensure that the corners of the foam core are positioned correctly into the corners of the cover Ensure that the profiled side of the foam is facing uppermost when packed into its cov
14. er 1576248 C Maintenance Invacare Softform Premier Active 2 and Active Care 8 After Use 8 1 Storage IMPORTANT Store mattresses in a dry environment Store mattresses within a protective cover Store items on clean dry off flooring free from sharp edges to avoid any possible damage Never store other items on top of a mattress Do not store mattresses next to radiators or other heating devices Protect mattresses from direct sunlight Refer to the storage and shipping conditions in section 10 4 Environmental Parameters page 24 8 2 Re Use A cleaning record must be kept as part of cleaning the system The product is suitable for repeated use The number of times it can be used depends on how often and in which way the product is used Before reuse clean the product thoroughly 7 2 Cleaning and care page 17 8 3 Disposal The disposal and recycling of used devices and packaging must comply with the applicable local legal regulations Ensure that the mattress is cleaned prior to disposal to avoid any risk of contamination 20 1576248 C 9 Troubleshooting 9 1 Identifying and repairing defects There are audio and visual alarms present on the control unit Troubleshooting Problem Alarm Cause Solution Mattress not inflating not alternating Mattress CPR hose disconnected Connect CPR hose connector lock it in place Has power
15. mal method of assessing risk from pressure ulcer development and should be used in conjunction with an informal assessment informed nursing judgement Informal assessment is considered to be of greater importance and clinical value This user manual contains important information about the handling of the product In order to ensure safety when using the product read the user manual carefully and follow the safety instructions For further information contact Invacare in your country addresses see back page of this user manual To access valuable information and useful links for Pressure Area Care training and education refer to www thinkpressurecare co uk Softform Premier Active 2 Mattress a novel step up step down approach British Journal of Nursing 2006 Vol 15 No II 1 2 Symbols in this user manual In this User Manual warnings are indicated by symbols The warning symbols are accompanied by a heading that indicates the severity of the danger avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided could result in product damage minor injury or both IMPORTANT Indicates a hazardous situation which if not avoided could result in damage to the product WARNING Indicates a potentially hazardous situation which if not gt Gives useful tips recommendations and information for efficient trouble free use n This product complies with the
16. mental Parameters Main Supply 220 240 V 50 Hz Operating conditions Rated Input Current LA Ambient temperature 5 40 C Supply Fuse LA Relative humidity 15 93 non condensing Noise Level lt 32 dB Atmospheric pressure 70 106 kPa Classification Class Il Type BF Storage and shipping conditions Cycle Time 10 min A B min Ambient temperature 25 70 C Size 237 mm x 205 mm x 80 mm Relative humidity 10 100 non condensing Weight 1 75 kg Atmospheric pressure 50 106 kPa Air Flow 4 l min 10 5 are parts Operating Pressure 60 mmHg 8 kPa Sp P il For spare parts components list please contact your nearest Power 23 VA Invacare dealer in your country specified on back of this Control unit fuse TI AL 250 V User manual 10 3 Materials Foam Polyurethane Combustion Modified High Resilience Foam Cover Polyurethane transfer coating on weft knitted fabric Air Cells Polyurethane coated nylon Glide Membrane Polyurethane Film Control unit and mattress components are Latex free 1576248 C 24 Notes Notes Notes Invacare distributors United Kingdom Invacare Limited Pencoed Technology Park Pencoed Bridgend CF35 5AQ Tel 44 0 1656 776 222 Fax 44 0 1656 776 220 uk invacare com www invacare co uk Australia Invacare Australia PTY Ltd Lenton Place North Rocks NSW 2151 Australia
17. ree prong wall outlet using the five meter power lead provided with the product Position the device ensuring that access to the connections on the device are not obscured and has ease of access WARNING If this equipment is modified appropriate inspection and testing must be conducted to ensure continued safe use of the equipment Do not modify this equipment without authorization of the manufacturer Setup WARNING Risk of entrapment Patient entrapment with the bed side rails may cause injury or death A thorough patient assessment should be completed and monitored and the equipment should be used as specified and maintained to reduce the risk of entrapment Variations in bed rail dimensions and mattress thickness size and density could increase the risk of entrapment Mattress must fit bed frame and side rails to prevent patient entrapment Follow the bed manufacturer s instructions After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Rails with dimensions different from the original equipment supplied or specified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury Invacare Softform Premier Active 2 and Active Care A WARNING This mattress is recommended to be installed on medical bed frames with bed sides or assist rails It is preferred that the rails to be in the raised position
18. result in a severe fire property damage and cause physical injury or death Do not use in oxygen rich environments A small electrical spark inside pump may cause explosion Do not smoke 1576248 C 2 2 EMC information IMPORTANT The information contained in this document is subject to change without notice Check all parts for shipping damage and test before using In case of damage do not use Contact Invacare Carrier for further instructions There is no known risk of adverse effects on the Active 2 Active Care control unit caused by other electromagnetic devices present at the time of treatment Similarly there is no known risk of the Active 2 Active Care control unit causing adverse effects on other electromagnetic devices 2 3 Symbols on the product Safety Type BF applied part Date of manufacture gt WEEE conform Keep dry Do not pierce or cut Oo Line dry Do not dry clean C CE conform User weight limit 80 Recommended 80 C Do not put near flame Do not iron Do not bleach Tumble dry low heat Class Il medical equipment Sax Refer to user manual 1576248 C Invacare Softform Premier Active 2 and Active Care 3 Components 3 1 Product description The Softform Premier Active 2 Active Care mattress system acts as a static pressure reducing suppo
19. rmation IMPORTANT Take care when handling mattresses to ensure no damage to the cover It is recommended that two people life carry mattresses Avoid contact with jewellery nails abrasive surfaces etc Do not drag mattresses Avoid contact with wall door frames door catches or locks etc Do not transport in roll cages unless completely protected from the sharp edges of the cage Refer to the storage and shipping conditions in section 10 4 Environmental Parameters page 24 6 2 Transport Mode If it is necessary to move the bed or mattress simply Turn off power supply 2 Disconnect control unit power lead if necessary the air hose 3 When system is ready to reactivate following section 4 2 Installing the system page 10 Air supply hose should be stored by attaching to the fastener at foot of the mattress For Active Care mattress the air hose is located inside the mattress To access the hose Unzip the mattress take out hose and connect to the pump ensure that zip is closed once connection is made 16 1576248 C 7 Maintenance 7 1 Inspection multiple use It is recommended that the mattress is checked foam air insert and cover for strike through this may include fluid ingress stains rips or damage after the release of each patient after ending of the period of use or on a minimum monthly basis depending on which occurs first by a suitably qualified and competen
20. rt mattress for patients at high risk that can by facilitating the air pump introduce effective alternating pressure if the patients condition requires alternating pressure therapy The water resistant cover provides a vapor permeable multi stretch surface to promote patient comfort and to maximise the effectiveness of the foam core The mattress is the only part intended to come into physical contact with the patient the only applied part with temperature of maximum 41 1 C 3 2 Components The following components are included within the scope of delivery U shape non castellated base layer Alternating air cell insert Castellated insert D Micro processor controlled control unit O Twin air connector hose Multi stretch vapour permeable cover Toughed PU coated base User Manual Power lead supplied not shown 1576248 C d Setup 4 1 Safety information A 1576248 C WARNING Electrical shock hazard Do not remove control unit cover Refer to qualified service personnel Before performing any maintenance to the control unit disconnect the power lead from the wall outlet Do not insert items into any openings of the control unit Doing so may cause fire or electric shock by shorting the internal components The control unit must be kept away from all heat sources and radiators during operation Connect the equipment to a two or th
21. s arrow Down then Press OK 3 second time limit between each function System OK with I underneath on LCD display System OK with 2 underneath on LCD display Pressure displayed on LCD display Pump display will revert back to System OK if no selection made within 15 seconds 4 Pressure adjustment en Pressure m Pressure 60mmHg Press OK button to select Pressure Arrow Up to selected pressure Arrow Down to selected pressure Press OK button Default set at 60mmHg There is a pressure transducer in the pump which limits the pressure 60 70 80 60 850 340 Desired pressure on LCD display is taken over and displayed under System OK 5 Language adjustment Press arrow Up Press arrow Down System OK with I underneath on LCD display System OK with 2 underneath on LCD display Press OK Pressure displayed Language Press arrow up or down Language displayed Press OK Language selected Navigate to desired language using zor Y Languages in local language are displayed individually A buttons English is default language For available languages see rg section 5 3 Control unit Software Schematic page 13 Press OK Selected language on display is taken over for the whole menu display 1576248 C 15 Invacare Softform Premier Active 2 and Active Care 6 Transport 6 1 Safety info
22. t person Check mattress multiple use Unzip the cover completely Check for any staining on the white underside of the cover Check for any staining on the interior foam Replace any stained items and dispose of as per local authority procedure Remove mains power and check audible sounder operates 6 Visually inspect mains cord for signs of damage or wear amp ON 7 2 Cleaning and care IMPORTANT All cleaning agents and disinfectants used must be effective compatible with one another and must protect the materials they are used to clean For further information on decontamination in health care environments please refer to The National Institute for Clinical Excellence guidelines on Infection Control www nice org uk CG139 and your local infection control policy Cleaning Handle The exterior of the Handle can be periodically wiped using a cloth dampened with disinfectant 1576248 C Maintenance Cleaning control unit 2 3 WARNING Electrical shock hazard Ensure the control unit is disconnected from the mains electricity supply before cleaning Do not spray disinfectant directly on to the control unit or immerse the control unit in any type of liquid This could result in a severe electrical hazard as this equipment has no protection against ingress of water This equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen
23. whenever the patient is on the bed Health care professionals assigned to each case should make the final decision as to whether side assist rails are warranted after assessing patient risk of entrapment Controls on the footboard may be obstructed by the control unit on a few bed frames lt may be necessary to relocate the control unit Before placing the patient on the bed check that air hoses and power cord are clear of moving bed components Operate all bed frame motorized functions through their full range of motion to be certain that there is no pulling interference or pinching Take care when positioning hoses and cables to eliminate the risk of tripping hazards or strangulation 4 2 Installing the system Place the pump unit at the end of the bed using the built in pump hooks Placing the pump on the floor will not affect the performance but may expose it to accidental damage 2 Detach the Softform Premier Active 2 Active Care twin hose from the end of the mattress 3 Connect it to the control unit An automatic click will signify a secure connection 4 Connect the mains power lead to the control unit and a suitable power supply 5 Switch on mains power 6 Switch on control unit switch System will pressurize see chart 5 3 Control unit Software Schematic page 13 shown by a green light and three audible beeps Correct pressure shown by a green light and t
24. wo audible beeps il Refer to section 5 4 Control unit Menu Display page 14 for shutdown procedure 1576248 C 5 Usage 5 1 Safety information Remove all packaging before use 2 Place the mattress directly on the frame of the bed The mattress is designed for beds with adjustable Iying surface A 1576248 C WARNING It is very important for the patient to reposition themselves or to be repositioned on a regular basis This must be based on the clinical judgement of a qualified health care professional This relieves pressure which helps prevent both tissue compression and potential ulcer formation Always consult a qualified health care professional before using the product Monitor the patient frequently CAUTION Make sure that the printed side of the mattress cover always faces upwards Make sure that the distance between the surface of the mattress and the top of the side rail is at least 220 mm Usage IMPORTANT If holes are present in the mattress cover there is a danger that liquids may ingress and contamination may occur Medical equipment including infusion pumps and monitors should be attached to appropriate bed accessories For home use common causes of damage include cigarette burns and the claws of pets that puncture sheets allowing fluid ingress and staining IMPORTANT Risk of damage to the mattress cover To prevent accidental damage do not
Download Pdf Manuals
Related Search