1.Operating elements and connections
Contents
1. technology TFT active matrix Display size Diagonally measured 7 0 inch Color system NTSC and PAL Dual System Sync horizontal 15625 Hz vertical 50 Hz Number of pixels 800 W x RGB x 480 H Dimension 231 0x 164 0 x 91 86 mm Audio level 1V 10k Power supply 12 24V 340mA Weight 2500 g Page 6 of 6 5 Operation 1 Contents 1 Switch on the device with the Main power switch 6 2 Select the right Video input 5 7 0 Monitor x 1 Power supply x 1 pc 3 Adjust the Brightness control inorder to obtain an image Sun Shield x 1 Bracket x pe Screws for Sun Shield M3x6 x 2 pcs as clear and sharp as possible Plastics Bolts x 2 pcs 4 Adjust the Volume for the headphones to desired level with the volume control Optional Washer A O17mmT 3 x 2pcs 5 You may push the reverse image function button 4 if the monitor is connected to a Rear View Camera 6 Please push OSD Control Menu 1 bottom to select the Brightness Contrast and 3 Display Mode that you wish to change then use L to get desired picture Plastics Bolts 1 4 xl2mmx 2 CAUTION When using headphones do not adjust a high vol Permanent high volumes may damage person s hearing The human ear gets accustomed to high volumes which do not seem to be that high after some time Therefore do not further increase a high volume after getting used to it 6 Application range Fig 1 Accessories The LCD color monitors offer a sharp2. Copyright 92009 by this company No Part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or any means whether Electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of this company SAFETY INSTRUCTION 1 Never push objects of any kind or spill liquid of any kind into these products 2 Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other risk Refer all servicing to qualified service personnel if any misuse mentioned above happened or any accident dropping miss operations occurred Page 1 of 6 7 Security notes The unit is only suitable for indoor use The heat being generated in the unit has to be removed via air circulation Therefore the circulation vents at the housings must not be covered with any objects Do not insert or drop anything into the air vents as this could result in a short circuit If the unit is used for purposes other than originally intended if it is connected in the wrong way or not repaired by authorized skilled personnel there is no liability for possible damage To cleaning only use a dry soft cloth by no means chemicals or water If the unit is to be put out of operation definitively bring it to a local recycling plant for disposal 8 Technical Data LCD
3. and high contrast display They can be universally applied e g in surveillance systems in reverse monitoring car systems or for multimedia applications Moreover an additional Audio input enables sound transmission via headphone Page 2 of 6 Page 5 of 6 2 Installation Sun Shield 5 Connect the Audio Out Put 12 To attach the Sun Shield onto the metal housing of Monitor use two M3x 6 6 Connect the SDI Input 14 to your SDI signal source screws to fasten it 7 Connect the SDI Output 15 or 16 to another Display you wish to use Bracket 8 Connect the TALLY 17 to your center control equipment Use the Plastics Bolts to fasten the Bracket Please put the washers in A B C 4 Connections And Operating elements order on both side to bracket into the Holes on the side of Monitor See attached 8 9 9 20 IN IN drawing No gt a gt gt a aA Mile a AA NS 7 Pia a OF a AO A 01 DA j 64 i 06107 Na DAN TING AN J Fig 3 Connectors and Controls 1 OSD Menu 2 Increase default to Brightness 3 Decrease default to Brightness 4 Left Right Up Down Reverse 5 Video Input selector 6 Main Power 7 LED Power Indicator 8 Video I Input Fig 2 Bracket Installation l E S l 9 Video II Input 10 Video Out Put The model in a metal case is suitable for mounting into furniture walls etc l 11 Audio Input 12 Audio Out Put Insert four screws into th
4. e mounting holes at the front panel and mount the 13 DC 12V Power Input 14 SDI Input device to desired location f 15 SDI Output 16 SDI Output 3 Connection 17 TALLY Connector 18 Green LED on 1 Connect the Video source to Video input I or II Sor 9 19 Red LED Of 20 Yellow Stand b 2 Connect the Audio input 11 Optional a wi y 3 Selector the correct video Input 5 Source 4 Connect an electronically regulated 12V power supply 13 Central positive Page 4 of 6 Page 3 of 6 ASC Y ma r NNN EN ee hy y l oo A a i N Model No LSD 7725 7 SDI LCD Monitor User s Manual Version 1 2
Download Pdf Manuals
Related Search